1 66 1100 077-2
Quick Reference
LCU
5352
Guide
S
C1
2 66 1100 077-2
Copyrights
The information in this document is subject to change at the sole discretion of ASSA ABLOY
without notice.
Any use, operation or repair in contravention of this document is at your own risk. ASSA ABLOY
does not assume any responsibility for incidental or consequential damages arising from the use
of this manual.
All information and drawings in this document are the property of ASSA ABLOY. Unauthorized use
and reproduction is prohibited.
Table of contents
EXPLODED VIEW ............................................................................................................ 3
INSTALLATION .............................................................................................................. 3
FCC STATEMENTS .......................................................................................................... 4
ISED (IC) STATEMENTS .................................................................................................. 4
REVISION HISTORY ......................................................................................................... 5
3 66 1100 077-2
Exploded view
Installation
LCU 5352SC1 is intended for limited use, i.e. for mounting in applicable ASSA ABLOY Global Solutions
products only. See below a mounting example in a VingCard Essence (v2) lock, ANSI (DA) variant with
cylinder, where LCU 5352SC1 is position 11. For additional mounting details, see the respective user manual
for the concerned product.
4 66 1100 077-2
Name/Model
Gain
Impedance
Chip antenna
-0.5 dBi
50 ohm
FCC statements
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.
Exposure statement:
This portable device with its antenna complies with FCC RF exposure limits for general population/
The antenna used for this device must not be co-located or operating in conjunction with any other antenna or transmitter.
Use only the supplied antenna.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environmen t. This transmitter
must not be co-located or operating in conjunction with any other antennas or transmitters. Changes or modifications
not expressly approved by the party responsible for compliance could void
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
The concerned LCU must be labeled to say 'FCC ID: Y7V-LCU5352SC1'.
The concerned end product must be labeled to say 'Contains FCC ID: Y7V-LCU5352SC1'.
the user's authority to operate the equipment.
uncontrolled exposure.
ISED (IC) statements
This device complies with Industry Canada licence-exempt RSS standard CAN ICES-3 (B)/ NMB-3(B) B. Operation is subject
to the following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may cause undesired operation of the device.
Le présent appareil est conform aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est
autorisée aux deux conditions suivantes:
(1) l'appareil ne doit pas produire de brouillage, et
(2) l’utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en
compromettre le fonctionnement.
Exposure statement:
This portable device with its antenna complies with FCC RF exposure limits for general population/ uncontrolled exposure.
The antenna used for this device must not be co-located or operating in conjunction with any other antenna or transmitter.
Use only the supplied antenna.
Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum
(or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users,
the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more
than that necessary for successful communication.
This radio transmitter IC9514A-LCU5352SC1 has been approved by Industry Canada to operate with the antenna type
listed below with the indicated maximum permissible gain and required antenna impedance. Antenna types not included
in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device.
The term "IC" before the equipment certification number only signifies that the Industry
Le terme "IC" devant le numéro de certification signifie seulement que les specifications techniques Industrie Canada ont
été respectées.
The concerned LCU must be labeled to say 'IC9514A-LCU5352SC1'.
The concerned end product must be labeled to say 'Contains IC9514A-LCU5352SC1'.
Canada technical specifications were met.
5 66 1100 077-2
Date
Change
By
January 22, 2019
Initial release
KG
October 29, 2019
Clarified that
LCU 5352SC1 is intended for
limited use, i.e. for mounting in applicable
ASSA ABLOY Global Solutions products only
Added mounting example
KG
November 6, 2019
Added ‘The concerned end product must be
labeled to say…’ for FCC and ISED respectively
KG
Revision history
Loading...