ASSALOY PRXTRMH1 Users manual
FCC ID: U4A-PRXTRMH1 IC ID: 6982A-PRXTRMH1 Report No. M060902_Cert_Rx
EMC Technologies Report Number: M060902_Cert_Rx
APPENDIX G
USER MANUAL
EMC Technologies Pty Ltd – 176 Harrick Road, Keilor Park VIC 3042 Australia
www.emctech.com.au
Installation Instructions For
Harmony Series
H1 Mortise Lock
© SARGENT Manufacturing Company 2007
A7877A
03/07
Table of Contents
1
Warning
2
General Description.....................................................1
3
Specifications............................................................1
4
Features ..................................................................1
5
Parts Breakdown .......................................................2-3
6
Installation Instructions ..............................................4-11
7
Operational Check......................................................12
Page
1
Warning
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this
device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates, uses and can radiate radio frequency energy and if not installed
and used in accordance with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that the interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or r
•
• Increase the separation between the equipment and receiver
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected
Consult the dealer or an experienced TV technician for help
•
This Class B digital apparatus complies with Canadian ICES-003.
Cet appar
elocate the r
eil numérique de la classe B est confor
Warning: Changes or modifications to this unit not expressly approved by the party
responsible for compliance could void the user's authority to operate the equipment.
eceiving antenna
me avec la norme NMB-003 du Canada.
Harmony Series H1 Mortise Lock
Harmony Series
H1
Wiegand
Access Control
System
(By Others)
Power
12VDC or 24VDC
2
General Description
The SARGENT Harmony Series H1 Mortise Lock is designed to interface with an existing weigand access
control system.
Specifications
3
• Latch - Stainless steel 3⁄4" projection one-piece
• Deadbolt - One-piece hardened stainless steel
• Guardbolt - Stainless steel, non-handed
• Handed - Easily field reversible without
opening case
• Case - 12 gauge heavy duty wrought steel
Features
4
• Complete monitoring of door from locks
•
Wires directly to Access Control System
• 12 or 24 VDC Fail Safe/Fail Secure
• Outside lever controlled by any prox credentials
• Inside lever provides REX signal and retracts latch
and deadbolt
• Locks furnished for 1-3/4" doors. Can be
furnished for other door sizes upon request.
Consult factory
• U.L. Listed (3 hr.)
• HID 125khz proximity credentials
•
All HID Bit formats
A7877A © SARGENT Manufacturing Company 2007
For installation assistance, contact SARGENT at 800-810-WIRE (9473)
1
1
2
3
4
5
6
7
8
9
10
11
10
12
13
14
8
6
5
1
5
16/17
18/19
2
0
21
22
23
24/25/26
27
28
29
29
28
27
3
0
31
32
33
34
Harmony Series H1 Mortise Lock
5
Parts Breakdown
© SARGENT Manufacturing Company 2007 A7877A
2
For installation assistance, contact SARGENT at 800-810-WIRE (9473)
Loading...