5300 Series Grade 2
Cylindrical Knob Lockset
Installation Instructions
Mark Door
1
Mark horizontal line across the edge
of the door at the height you want to
install knob. Fold template over
edge of door, centering on horizontal
line. Mark centers of holes.
-IMPORTANT-
4
Adjust for Door Thickness
To adjust lock rotate outside rose and
position as indicated in accord with the
door thickness. To adjust for any door
thickness between 1-3/8" and 1-3/4"
set the rose plate at a suitable
intermediate position.
1/8" (3.2mm)
1-3/8" (35mm)
1-3/4" (44mm)5/16" (8.0mm)
Lock Case
Install Latch Unit
2
Bore 2-1/8" hole through door, and hole
into edge of door at points marked on
the door. Cut out for latch front 5/32"
deep and install latch unit.
Notches required
on Hard Laminate
& Metal Doors
Install Lock
5
With lock case in place, insert lock
assembly into 2-1/8" (54mm) hole,
making sure that lock case hooks the
retainer legs and retractor engages the
bolt tail. Do Not Force.
Caution: If deadlocking latch unit is
installed, do not attempt to mount
lock unit with door closed, as
deadlocking plunger bar will interfere.
Retractor
Retainer Leg
Remove Inside Knob
3
4
If knob retainer is not visible, turn inside
knob counterclockwise approximately
45°. Use small nail or wire to depress
retainer and slide knob off.
NOTE: For 5316 Lockset only. To
remove inside knob, follow instructions
in Step 9 under heading "All 5300
Series Locksets".
Install Inside Rose Plate and Rose
6
Slip on rose plate and locate screw
holes on vertical centerline. Insert
machine screws and tighten
alternately to obtain secure attachment.
Place rose over rose plate aligning
notch in rose with tab on rose plate and
snap rose down flush with door.
Vertical
Rose
Rose Plate
Tab
Outside Rose
Install Inside Knob
7
Align lug on knob with narrow slot on
side of spindle and push knob all the
way in until retainer clicks into slot on
knob.
NOTE: For 5305 lock only.
Refer to Step 9 before installing
inside knob. When installing knob
make sure button is pushed in and
turned clockwise to lock outside knob.
An ASSA ABLOY Group brand
Bolt Tail
Lock Case
Install Strike
8
Mark height line for strike on jamb.
Mark vertical centerline on jamb. This
centerline must be same distance from
door stop as latch unit centerline is from
edge of door which will hit stop. Cut
mortise in jamb for strike and box (if
used). Insert box and strike and tighten
screws securely.
(497) (371)
Notch
-IMPORTANT-
9
All locks are set for a right hand door.
If the lock is properly installed, the cuts
on the key will be facing up when the
key is inserted into the knob.
Right Way Wrong Way
80-9150-0033-010 (08-12)
To Change Lock Hand or Remove Cylinder for Rekeying
All 5300 Series Locksets
Except Locks described below.
Outside knob must be in unlocked position.
Insert key halfway into cylinder. Rotate knob
counter-clockwise until knob retainer lines up
with hole in trim cap. Depress retainer with a
nail or pointed tool and slide knob off. Turn
knob and cylinder 180°. Reinstall using key to
align cylinder in lock. Do not insert key more
than halfway when reinstalling knob. Push
knob in until retainer snaps into place.
5305 Lockset
Outside knob must be in unlocked position.
With inside knob removed, turn button to
unlock outside knob. Insert key halfway into
cylinder. Rotate knob counter-clockwise until
knob retainer lines up with hole in trim cap.
Depress retainer with a nail or pointed tool and
slide knob off. Turn knob and cylinder 180°.
Reinstall using key to align cylinder in lock. Do
not insert key more than halfway when
reinstalling knob. Push knob in until retainer
snaps into place.
5316 Lockset
8
(Outside knob only) Insert key and rotate to the
unlocked position. Turn knob counter-clockwise
until knob retainer lines up with hole in trim cap.
Depress retainer with a nail or pointed tool.
(Caution: At this point slide knob out not more
than 1/8", rotate key counter-clockwise and
withdraw halfway out of cylinder.) Slide knob
off. Turn knob and cylinder 180°. Reinstall using
key to align cylinder in lock. Do not insert key
more than halfway when reinstalling knob.
Push knob in until retainer snaps into place.
5320 Lockset
Insert key into cylinder and rotate 90°
clockwise. Depress retainer with a nail or
pointed tool and slide knob off. Turn knob and
cylinder 180°. To reinstall knob you must use
key to align cylinder in spindle, then rotate 90°
clockwise and push knob in until retainer snaps
into place.
Any retrofit or other field modification to a fire rated opening can potentially impact the fire rating of the opening, and Yale Locks & Hardware makes no representations or warranties
concerning what such impact may be in any specific situation. When retrofitting any portion of an existing fire rated opening, or specifying and installing a new fire-rated opening,
please consult with a code specialist or local code official (Authority Having Jurisdiction) to ensure compliance with all applicable codes and ratings.
Yale® is a registered trademark of Yale Security Inc., an ASSA ABLOY Group company. Other products' brand names may be trademarks or registered trademarks of their
respective owners and are mentioned for reference purposes only. These materials are protected under U.S. copyright laws. All contents current at time of publication.
An ASSA ABLOY Group brand
Product Support Tel 800.438.1951 • www.yalelocks.com
Yale Locks & Hardware is a division of Yale Security Inc., an ASSA ABLOY Group company.
Yale Security Inc. reserves the right to change availability of any item in this catalog, its design, construction, and/or its materials.
All rights reserved. Reproduction in whole or in part without the express written permission of Yale Security Inc. is prohibited.
Copyright © 1989, 2012, Yale Security Inc., an ASSA ABLOY Group company.
2
80-9150-0033-010 (08-12)
Loading...