ASRock Rack X570D4U-2L2T Service Manual

X570D4U-2L2T

X570D4U

User Manual

Version 1.0

Published July 2020

Copyright©2020 ASRock Rack INC. All rights reserved.

X570D4U-2L2T / X570D4U

Chapter 1 Introduction

ank you for purchasing ASRock Rack X570D4U-2L2T/ X570D4U motherboard,

a reliable motherboard produced under ASRock Rack’s consistently stringent quality

control. It delivers excellent performance with robust design conforming to ASRock

Rack’s commitment to quality and endurance.

Becau se the motherboard specications and the BIOS soware might be updated, the con­tent of thi s manual will be subject to change without notice. In case any modications of
this manual occ ur, the updated version will be available on ASRock Rack website without
further notice. You may nd the lates t memor y and CPU support lists on ASRock Rack
website a s well. ASRock Rack’s Website: www.ASRockRack.com

If you require technical support related to this motherboard , please visit our website for
specic information about the model you are using.
http://www.asrockrack.com/support/

1.1 Package Contents

ASRock Rack X570D4U-2L2T / X570D4U Motherboard

•

(micro-ATX Form Factor: 9.6-in x 9.6-in, 24.4 cm x 24.4 cm)

Quick Installation Guide

•

1 x I/O Shield

•

1 x SATA3 Cable (60cm)

•

2 x Screws for M.2 Sockets

•

If any items are miss ing or appear dam aged, contact your authorized dealer.

English

English

1.2 Specications

X570D4U-2L2T / X570D4U

MB Physical Status

Form Factor micro -ATX
Dimension 9.6'' x 9.6'' (24.4 cm x 24.4 cm)
Processor System

CPU 3rd generation AMD Ryzen™ and 2nd generation AMD Ryzen™

with Radeon™ Vega7 Graphics Processors
Socket AM4 PGA 1331
Chipset AMD X570
System Memory
Capacity - 4 x 288-pin DDR4 DIMM slots

- Support up to 128GB DDR4 ECC/UDIMM

Type - Dual Channel DDR4 memory technology

- Support DDR4 ECC/UDIMM

*Conditionally supports ECC error reporting function.

DIMM Size Per

DIMM
DIMM Frequency - ECC/UDIMM: up to 3200MHz

Vol t a ge 1.2V
Expansion Slot
PCIe 3.0/4.0 x 16 Matisse:

PCIe 3.0/4.0 x 8 Matisse:

PCIe 3.0/4.0 x 1 Matisse:

Storage
SATA Controller 8 x SATA3 6.0 Gb/s (SATA0-7, SATA_0 supports SATA DOM),

M.2 Slot 2 (M2_1: 2242/2260/2280/22110, supports SATA3 (6.0 Gb/s) or

- ECC/UDIMM: 32GB, 16GB, 8GB

PCIE6: Gen4 x16 link, auto switch to x8 link if Slot 4 is

occupied (Physical x16, EE x16/x8, shared with Slot 4)

Picasso:

PCIE6: Gen3 x8 link (Physical x16, EE x8)

PCIE4: Gen4 x8 link (Physical x8, EE x0/x8, shared with Slot 6)

Picasso:

PCIE4: N/A (not supported)

PCIE5: Gen4 x1 link

Picasso:

PCIE5: Gen3 x1 link

support R AID 0, 1, 10

PCIE4.0(x4)(Matisse) / PCIE3.0(Picasso)(x4) ;

M2_ 2: 2242/2260/2280, supports SATA3 (6.0 Gb/s) or

PCIE4.0(x4)(Matisse) / PCIE3.0(Picasso)(x4)

2 3

Ethernet
Interface X570D4U-2L2T:

10000/1000 /100 /10 Mbps

X570D4U:

100 0 /10 0 /10 Mbps

LAN Controller X570D4U-2L2T:

- 2 x RJ45 10G base-T by Intel® X550-AT2

- 2x RJ45 1G base-T by Intel® I210-AT

- 1 x RJ45 Dedicated IPMI LAN port by RTL8211E

- Supports Wake-On-LAN

- Supports Energy Ecient Ethernet 802.3az

- Supports Dual LAN with Teaming function

- Supports PXE

- LAN3 supports NCSI

X570D4U:

- 2x RJ45 1G base-T by Intel® I210-AT

- 1 x RJ45 Dedicated IPMI LAN port by RTL8211E

- Supports Wake-On-LAN

- Supports Energy Ecient Ethernet 802.3az

- Supports Dual LAN with Teaming function

- Supports PXE

- LAN1 supports NCSI
Management
BMC Controller ASPEED AST2500
IPMI Dedicated

GLAN
Features Watch Dog
Graphics
Controller ASPEED AST2500
VRAM DDR4 16MB
Rear Panel I/O
VGA Port 1 x D-Sub
Serial Port 1 x COM port
USB 3.1 (Gen 2)

Port
HDMI 1 (only supported for Picasso(APU))

1 x Realtek RTL8211E for dedicated management GLAN

2

X570D4U-2L2T / X570D4U

English

LAN Port X570D4U-2L2T:

- 2 x RJ45 1 Gigabit Ethernet LAN ports

- 2 x RJ45 10 Gigabit Ethernet LAN ports

- 1 x RJ45 Dedicated IPMI LAN port

- LAN Ports with LED (ACT/LINK LED and SPEED LED)

X570D4U:

- 2 x RJ45 1 Gigabit Ethernet LAN ports

- 1 x RJ45 Dedicated IPMI LAN port

- LAN Ports with LED (ACT/LINK LED and SPEED LED)
UID 1
Internal Connector
Auxiliary Panel

Header
Front Panel 1 (RST, PWRBTN, HDDLED, PWRLED)
TPM Header 1 (17-pin LPC TPM header, supports TPM 1.2/2.0)
SPI TPM Header 1 (13-pin SPI TPM header, supports TPM 2.0)
IPMB Header 1
Fan Header 3 (6-pin), 3 (4-pin)
ATX Power 1 x (24-pin) + 1 x (4-pin)
USB 3.1 Gen1

Header
M.2 2
SATA DOM 1
BMC _SMB1 1
PSU_SMB1 1
SPEAK ER 1
TR1 1
Front VGA 1
Front LAN LED X570D4U-2L2T: 1

1 (includes chassis intrusion, location button & LED, front

LAN LED, system fault, and BMC alert)

1 (supports 2 USB 3.1 Gen1 ports)

X570D4U: N/A
80 debug port LED 1
Buzzer 1
Clear CMOS 1 (short pad)
OH/FanFail LED 6
System BIOS
BI O S Ty pe 32MB AMI UEFI Legal BIOS
BIOS Features - Plug and Play (PnP)

English

- ACPI 2.0 Compliance Wake Up Events

- SMBIOS 2.8 Support

- ASRock Rack Instant Flash

4 5

X570D4U-2L2T / X570D4U

Hardware Monitor
Temperature - CPU/FCH/DDR/LAN* Temperature Sensing

- MB/Card Side Temperature Sensing

*LAN Temperature Sen sing is suppor ted for X570D4U-2L2T only.

Fan - Fan Tachometer

- Quiet Fan (Allow Chassis Fan Speed Auto-Adjust by CPU

Temperature)

- Fan Multi-Speed Control

Vol t a ge Voltage Monitoring: 3VSB, 5VSB, VCPU, VSOC, VCCM, APU

VDDP, PM VDD CLDO, PM VDDCR S5, PM VDDCR, BAT,

3V, 5V, 12V
Support OS
OS Microso® Windows®:

Windows 10 (64 bit)

Linux®:

- UBuntu 18.04 (64 bit)

- RedHat Enterprise Linux Server 8.1 (64bit)

* Please refer to our website for the latest OS support list.

* e Linux s ystem doesn’t support Raid mode .

* Suppor ts UEFI BOOT only.

Environment
Temperature Operation temperature: 10°C ~ 35°C / Non operation

temperature: -40°C ~ 70°C

NOTE: Please refer to our website for th e latest specications.

is motherboard suppor ts Wake from on Board LAN. To use this func tion, please make
sure that the “Wake on Magic Packet from power o state” is enabled in Device Manager
> Intel® Ethernet Connec tion > Power Manage ment. And the “PCI Devices Power On” is
enabled in UEFI SETUP UT ILITY > Advanced > ACPI Conguration. Aer that, onboard
LAN3&4 c an wake up S5 under OS.

If you install Intel® LAN utility or Marvell S ATA utility, this motherboard may fail Win­dows® Hardware Quality Lab (WHQL) certi cation tests. If you install the drivers only, it
will pa ss the WHQL tests.

English

1.3 Unique Features

ASRock Rack Instant Flash is a BIOS ash utility embedded in Flash ROM. is con-

venient BIOS update tool allows you to update system BIOS without entering operat-

ing systems rst like MS-DOS or Windows®. With this utility, you can press the <F6>

key during the POST or the <F2> key to enter into the BIOS setup menu to access

ASRock Rack Instant Flash. Just launch this tool and save the new BIOS le to your

USB ash drive, oppy disk or hard drive, then you can update your BIOS only in a

few clicks without preparing an additional oppy diskette or other complicated ash

utility. Please be noted that the USB ash drive or hard drive must use FAT32/16/12

le system.

English

6 7

X570D4U-2L2T / X570D4U

24.4cm (9.6 in)

24. 4cm (9. 6 in)

ATXPWR1

VGA1

COM1

DDR4_A2 (64 bit, 288-pin module)

DDR4_A1 (64 bit, 288-pin module)

DDR4_B2 (64 bit, 288-pin module)

DDR4_B1 (64 bit, 288-pin module)

ATX12V3

USB 3. 1

Gen1

T: USB3_ 2

B: USB 3_1

IPMI _LAN

UID1

USB3_3_4

PCIE5

PCIE6

PCIE4

M2_2

M2_1

NUT42_2

NUT80_2

X57 0D4U- 2L2T /

X57 0D4U

BMC
ROM

Socket

AM4 PGA 1331

1

PSU_SMB1

FAN3

NUT42_1

NUT60_1

NUT80_1

NUT110_1

CLRCMOS1

1

AUX_PANEL1

HDLED RESET

PLED PWRBTN

PANEL1

1

Dr.

Debug

TPM1

1

SPEAKER1

1

CHASSIS_ID1

1

1

IPMB_1

BMC_SMB_1

BUZZER1

RoHS

231 4

8

7

9

10
11
12

13

14

16

17

18

19

20

15

21222325

2930

313233

LAN3

LAN4

LAN 2

LAN 1

HDMI1

1

LED_LAN_3_4

1

FRNT_V GA1

BAT1

FAN4

FAN5

FAN6

SATA_0

SATA_1

X550

SATA_2

SATA_3

SATA_4

SATA_5

SATA_7

SATA_6

FAN1

1

FAN2

Super

I/O

1

TPM_BIOS_PH1

1

SATAPWR1

BIOS
ROM

T 1

R

1

1

CHASSIS_ID2

1

CHASSIS_ID3

5

6

AMD
X570

24262728

34

35

36

ASPEED

2500

NUT60_2

(X570D4U-2L2T only)

(X570D4U-2L2T only)

(X570D4U-2L2T only)

(X570D4U-2L2T only)

1.4 Motherboard Layout

English

English

No. Description

1 ATX 12V Power Connector (ATX12V3)

2 2 x 288-pin DDR4 DIMM Slots (DDR4_ A1, DDR4_B1, Blue)*

3 PSU SMBus Header (PSU_SMB1)

4 ATX Power Connector (ATXPWR1)

5 System Fan Connector (4-pin) (FAN3)

6 System Fan Connector (6-pin) (FAN4)

7 System Fan Connector (6-pin) (FAN5)

8 2 x 288-pin DDR4 DIMM Slots (DDR4_ A2, DDR4_B2, White)*

9 System Fan Connector (6-pin) (FAN6)

10 SATA DOM Power Connector (SATAPWR1)

11 AM4 PGA 1331 Socket

12 M.2 Socket (M2_2) (Type 2242 / 2260 / 2280)

13 SATA3 DOM Connector (SATA_0), Red

14 USB 3.1 Gen1 Header (USB3_3_4)

15 SATA3 Connector (SATA_1)

16 M.2 Socket (M2_1) (Type 2242 / 2260 / 2280 / 22110)

17 SATA3 Connector (SATA_3)(Upper), SATA3 Connector (SATA_2)(Lower)

18 TPM-SPI Header (TPM_BIOS_PH1)

19 SATA3 Connector (SATA_5)(Upper), SATA3 Connector (SATA_4)(Lower)

20 SATA3 Connector (SATA_7)

21 SATA3 Connector (SATA_6)

22 ermal Sensor Header (TR1)

23 System Panel Header (PANEL1)

24 Auxiliary Panel Header (AUX_PANEL1)

25 Clear CMOS Pad (CLRMOS1)

26 System Fan Connector (4-pin) (FAN1)

27 System Fan Connector (4-pin) (FAN2)

28 TPM Header (TPM1)

29 Chassis ID1 Jumper (CHASSIS_ID1)

30 Speaker Header (SPEAKER1)

31 BMC SMBus Header (BMC_SMB_1)

32 Intelligent Platform Management Bus Header (IPMB_1)

33 Chassis ID2 Jumper (CHASSIS_ID2)

(Reser ved for BOM option)

(Reser ved for BOM option)

8 9

X570D4U-2L2T / X570D4U

No. Description

34 Chassis ID3 Jumper (CHASSIS _ID3)

35 Front LAN LED Connector (LED_LAN_3_4)

36 Front VGA Header (FRNT_VGA1)

*For DIMM in stallation and conguration in struction s, please see p. 21 (Installation of Memory Modules
(DIMM)) for more detail s.

(Reser ved for BOM option)

(X570D4U-2L 2T only)

English

1.5 Onboard LED Indicators

ATXPWR1

DDR4_A2 (64 bit, 288-pin module)

DDR4_A1 (64 bit, 288-pin module)

DDR4_B2 (64 bit, 288-pin module)

DDR4_B1 (64 bit, 288-pin module)

ATX12V3

PCIE4

ASPEED

2500

X57 0D 4U- 2L 2T

BMC
ROM

Socket

AM4 PGA 1331

FAN3

1

1

1

1

IPMB_1

BMC_SMB_1

RoHS

1

FAN4

FAN5

FAN6

FAN1

1

FAN2

BIOS
ROM

1

CHASSIS_ID2

1

CHASSIS_ID3

AMD
X570

2

3

4

1

5

6

7

8

English

10 11

X570D4U-2L2T / X570D4U

No. Item Status Description

1 SB_PWR1 Green STB PWR ready

2 FAN _LE D3 Amber FAN3 f aile d

3 FAN _LE D4 Amber FAN 4 f a ile d

4 FAN _LE D5 Amber FAN5 f aile d

5 FAN _LE D6 Amber FAN6 failed

6 FAN _LE D1 Amber FAN1 f aile d

7 FAN _LE D2 Amber FAN2 f aile d

8 BMC _LED1 Green BMC heartbeat LED

English

1.6 I/O Panel

2

6 9

4

English

1

No. Description No. Description

1 VGA Por t (VGA1) 6 LAN RJ-45 Port (IPMI_LAN1)*

2 Serial Port (COM1) 7 HDMI Port

3 1G LAN RJ-45 Port (LAN1) 8

4 1G LAN RJ-45 Port (LAN2) 9

5 USB 3.1 Gen2 Ports (USB3_1_2) 10 UID Switch (UID1)

*ere are two LED next to the LAN port. Please refer to the table below for the LAN port

LED indications.

Dedicated IPMI LAN Port LED Indications

Activity / Link LED Speed LED

Status Description Status Description

O No Link O 10M bps connection or no

Blinking Yellow Data Activity Yel low 100M bps connection
On Link Green 1Gbps connection

3

5

10G LAN RJ-45 Port (LAN3)**

(X570D4U-2L 2T only)

10G LAN RJ-45 Port (LAN4)**

(X570D4U-2L 2T only)

ACT/LINK LED

SPEED LED

LAN Por t

7

8

link

10

12 13

X570D4U-2L2T / X570D4U

**ere are two LEDs on each LAN port. Please refer to the table below for the LAN port

LED indications.

ACT/LINK LE D

SPEED LE D

ACT/LINK LE D

LAN Port

10G LAN Port (LAN3, LAN4) LED Indications

SPEED LE D

(X570D4U-2L 2T only)

Activity / Link LED Speed LED

Status Description Status Description

O No Link O 10M/10 0M bps

connection or no link
Blinking Yellow Data Activity Orange 1Gbps connection

On Link Green 10Gbps connection

ACT/LINK LE D

ACT/LINK LE D

LAN Port

SPEED LE D

SPEED LE D

1G LAN Port (LAN1, LAN2) LED Indications

Activity / Link LED Speed LED

Status Description Status Description

O No Link O 10Mbps connection or

no link
Blinking Orange Data Activity Yellow 100Mbps connection
On Link Green 1Gbps connection

English

1.7 Block Diagram

X570D4U-2L2T:

SLOT 6 x16

SLOT 4 x8

SLOT 5 x1

English

PCIe4.0 x4/SATAI II

2xUSB3.1 Gen1

2xUSB2.0

X570

2xUSB3.1 Gen2

PCIe4.0 x1

Upstream Li nk

PCIe4.0x4

AMD

PCIe2.0 x1

LPC/eSPI

USB2.0

NCT6796D-R

Sw itch

32MB

BIOS

LPC

PCIeUSB

SPI

AST2500

ASPEED

MAC

UAR T

MAC

VGA

RGMII

8x SAT AIII

BXB-C

PCIe3.0x4

PCIe2.0x1

PCIe2.0x1

X550

-AT2

i210

i210

2xUSB2.0

PCIe4.0 x4/SATAIII

AMD AM4 Socket

TDP: max. 105W

PGA 1331

NCSI

PCIe4.0x8

MUX

Processor

HDMI

PCIe4.0x8

AMD Ryzen™

DDR4

DDR4

A

B

8211E

Share NIC

IPMI

RTL

D-Sub

COM port

14 15

X570D4U:

X570D4U-2L2T / X570D4U

COM port

D-Sub

RTL

8211E

IPMI

Share NIC

NCSI

B

A

DDR4

DDR4

Processor

AMD Ryzen™

PCIe4.0x8

HDMI

PCIe4.0x8

PGA 1331

TDP: max. 105W

AMD AM4 Socket

MUX

PCIe4.0 x4/SATAIII

RGMII

VGA

PCIeUSB

MAC

UAR T

MAC

ASPEED

AST2500

BIOS

LPC

32MB

LPC/eSPI

Upstream Li nk

PCIe4.0x4

2xUSB3.1 Gen1

2xUSB2.0

SPI

Sw itch

2xUSB3.1 Gen2

2xUSB2.0

i210

i210

NCT6796D-R

USB2.0

PCIe2.0 x1

X570

AMD

PCIe4.0 x1

PCIe4.0 x4/SATAI II

PCIe2.0x1

PCIe2.0x1

BXB-C

8x SAT AIII

SLOT 5 x1

SLOT 4 x8

SLOT 6 x16

English

Chapter 2 Installation

This is a micro-ATX form factor (9.6” x 9.6”, 24.4 cm x 24.4 cm) motherboard. Before

you install the motherboard, study the cong uration of your chassis to ensure that t he

motherboard ts into it.

Make sure to unplug the power cord before installing or removing the mothe rboard . Failure
to do so may cause physical injuries to you and d amages to motherboard components.

2.1 Screw Holes

Place screws into the holes indicated by circles to secure the motherboard to the chassis.

Attention! Before installing this motherboard, be sure to unscrew and remove the standos
at the marked location, under the motherboard, from the chassis, in ord er to avoid electri­cal shor t circuit and damage to your motherboard.

Do not over-tighten the screws! Doing so may damage the motherboard.

2.2 Pre-installation Precautions

Take note of the following precautions before you install motherboard components or

change any motherboard settings.

1. Unplug the power cord from the wall socket before touching any components.

2. To avoid damaging the motherboard ’s components due to static electricity, NEVER

place your motherboard directly on the carpet or the like. Also remember to use a

grounded wrist strap or touch a safety grounded object before you handle the compo-

nents.

3. Hold components by the edges and do not touch the ICs.

4. Whenever you uninstall any component, place it on a grounded anti-static pad or in

the bag that comes with the component.

5. When placing screws into the screw holes to secure the motherboard to the chassis,

please do not over-tighten the screws! Doing so may damage the motherboard.

English

Before you install or remove any component, ensure that the power is switched o or the
power cord is detached f rom the power supply. Failure to do so may cau se severe damage to
the motherboard, peripherals, and/or components.

16 17

2.3 Installing the CPU

Unplug all power cables be fore ins talling the CPU.

1

X570D4U-2L2T / X570D4U

o

90

2

English

3

English

18 19

X570D4U-2L2T / X570D4U

2.4 Installing the CPU Fan and Heatsink

Aer you install the CPU into this motherboard, it is necessary to install a larger

heatsink and cooling fan to dissipate heat. You also need to spray thermal grease

between the CPU and the heatsink to improve heat dissipation. Make sure that the

CPU and the heatsink are securely fastened and in good contact with each other.

Please be aware of the maximum dimen sions of the heatsink to be used is 116 * 83.65mm.

Please turn o the power or remove the power cord before changing a CPU or heat sink.

Installing the CPU Box Cooler SR1

1

English

2

3

English

20 21

X570D4U-2L2T / X570D4U

4

English

2.5 Installing Memory Modules (DIMM)

is motherboard provides four 288-pin DDR4 (Double Data Rate 4) DIMM slots,

and supports Dual Channel Memory Technology.

1. For dual channel conguration, you always need to install ide ntical (the same

brand, speed , size and chip-type) DDR4 DIMM pairs.

2. It is unable to activate Dual C hannel Memory Technology with only one or three
memory module installed.

3. It is not allowed to install a DDR , DDR2 or DDR3 memor y module into a DDR4
slot; otherwise, this mothe rboard and DIMM may be damaged.

DDR4 UDIMM Maximum Frequency Support

Ryzen Series CPUs

UDIMM Memory Slot Picasso Ridge Matisse Ridge

A2 A1 B2 B1 Freq (Mhz) Freq (Mhz)

- SR - - 2666 320 0

- DR - - 2400 3200

- SR - SR 2666 320 0

- DR - DR 2400 3200

SR SR SR SR 2133 2933

DR DR DR DR 1866 2666

English

22 23

X570D4U-2L2T / X570D4U

1

2

3

e DIMM only ts in one correc t orientation . It will cause pe rmanent damage to the
motherboard and the DIMM if you force the DIMM into the slot at incorrect orientation.

English

2.6 Expansion Slots (PCI Express Slots)

ere are 3 PCI Express slots on this motherboard.

PCIE slot:

Matisse:

PCIE4 (PCIE 4.0 x8 slot, from CPU) is used for PCI Express x8 lane width cards.

PCIE5 (PCIE 4.0 x1 slot, from Premium) is used for PCI Express x1 lane width cards.

PCIE6 (PCIE 4.0 x16 slot, from CPU) is used for PCI Express x16 lane width cards.

Slot Generation Mechanical Electrical Source

PCIE6 4.0 x16 x16 CPU

PCIE5 4.0 x1 x1 Premium

PCIE4 4.0 x8 x8 CPU

PCIe Slot Congurations

PCIE4 PCIE6

Single PCIE Card N/A x16

Two PCIE Cards x8 x8

Picasso:

PCIE4 is not supported.

PCIE5 (PCIE 3.0 x1 slot, from Premium) is used for PCI Express x1 lane width cards.

PCIE6 (PCIE 3.0 x16 slot, from CPU) is used for PCI Express x8 lane width cards.

Slot Generation Mechanical Electrical Source

PCIE6 3.0 x16 x8 CPU

English

PCIE5 3.0 x1 x1 Premium

PCIE4 N/A x8 N/A N/A

24 25

X570D4U-2L2T / X570D4U

Installing an expansion card

Step 1. Before installing an expansion card, please make sure that the power

supply is switched o or the power cord is unplugged. Please read the

documentation of the expansion card and make necessary hardware

settings for the card before you start the installation.

Step 2. Remove the system unit cover (if your motherboard is already installed

in a chassis).

Step 3. Remove the bracket facing the slot that you intend to use. Keep the

screws for later use.

Step 4. Align the card connector with the slot and press rmly until the card is

completely seated on the slot.

Step 5. Fasten the card to the chassis with screws.

Step 6. Replace the system cover.

English

2.7 Jumpers Setup

e illustration shows how jumpers are setup. When the jumper cap is placed on

the pins, the jumper is “Short”. If no jumper cap is placed on the pins, the jumper

is “Open”. e illustration shows a 3-pin jumper whose pin1 and pin2 are “Short”

when a jumper cap is placed on these 2 pins.

Reserved for BOM options:

Chassis ID1 Jumper

(3-p in CH ASSI S _ I D1)

(see p.7, No. 29)

Chassis ID2 Jumper

(3-pin CHAS SIS_ID2)

(see p.7, No. 33)

Chassis ID3 Jumper

(3-pin CHAS SIS_ID3)

(see p.7, No. 34)

Board Level SKU (Default) Reserved for system level

use

Reserved for BOM options:

Chassis ID1 Jumper

(3-p in CH ASSI S _ I D1)

(see p.7, No. 29)

Chassis ID2 Jumper

(3-pin CHAS SIS_ID2)

(see p.7, No. 33)

English

Chassis ID3 Jumper

(3-pin CHAS SIS_ID3)

(see p.7, No. 34)

Reserved for system level

use

Reserved for system level

use

26 27

Reserved for BOM options:

Chassis ID1 Jumper

(3-p in CH ASSI S _ I D1)

(see p.7, No. 29)

Chassis ID2 Jumper

(3-pin CHAS SIS_ID2)

(see p.7, No. 33)

Chassis ID3 Jumper

(3-pin CHAS SIS_ID3)

(see p.7, No. 34)

Reserved for BOM options:

Chassis ID1 Jumper

(3-p in CH ASSI S _ I D1)

(see p.7, No. 29)

Chassis ID2 Jumper

(3-pin CHAS SIS_ID2)

(see p.7, No. 33)

Chassis ID3 Jumper

(3-pin CHAS SIS_ID3)

(see p.7, No. 34)

Reserved for system level

use

Reserved for system level

use

X570D4U-2L2T / X570D4U

Reserved for system level

use

Reserved for system level

use

English

2.8 Onboard Headers and Connectors

Onboard headers and connectors are NOT jumpers. Do NOT place jumper caps over th ese
heade rs and connectors. Placing jumper caps o ver the headers and connectors will cause
permanent damage to the motherboard.

System Panel Header

(9-pi n PANEL1)

(see p.7, No. 23)

PWRBTN (Power Switch):

Connec t to the power switch on the chassi s front panel. You may congure the way to tur n
o your system using the power switch.

RESET (Reset Switch):
Connec t to the reset switch on the chassi s front panel. Press the reset sw itch to restart the
computer if the computer f reezes and fails to per form a normal restar t.

PLED (Syste m Power LED):
Connec t to the power status indicator on th e chassis front panel . e LED is on when the
system is operating. e LED is o when the syste m is in S4 sleep state or powered o (S5).

HDLED (Ha rd Drive Activity LED):
Connec t to the hard drive ac tivity LED on the chassis front panel. e LED is on when the
hard drive is reading or wr iting data.

e front panel de sign may dier by chass is. A front panel module m ainly consist s of power
switch, reset switch , power LED, hard dr ive activity LED, speaker and etc. When connect­ing your ch assi s front panel module to thi s header, make sure the wire a ssignments and the
pin assignments are matched correctly.

1

PLED+

PLED-

HDLED-

HDLED+

PWRBTN#

GND

GND

RESET#

GND

Co n nec t t h e power sw i tch,

reset switch and system status

indicator on the chassis to this

he ade r acco rdin g to the pi n

assignments. Particularly note

the positive and negative pins

before connecting the cables.

English

28 29

X570D4U-2L2T / X570D4U

Auxiliary Panel Header

(18-pin AUX_PANEL1)

(see p.7, No. 24)

A. Front panel SMBus connecting pin (6-1 pin FPSMB)
is hea der allows you to connect SMBus (Sys tem Management Bus) equipment. It can
be used for communication between peripheral e quipment in the system, which has slower
transmission rates, and power management equipment .

B. Internet status indicator (2-pin LAN3_ LED, LAN4_ LED)
ese two 2-pin headers allow you to use the Gigabit internet indicator cabl e to connect
to the LAN status indicator. When this indicator ickers , it means that the internet is prop­erly connected.

C. Cha ssis intrusion pin (2-pin CHASSIS)
is hea der is provided for hos t computer chassis with chassis int rusion detection design s.
In addition, it mu st also work with e xternal detection equipment, such as a chassis intru­sion detection sensor or a microswitch . When this function is activated, if any chassis
component movement occ urs, the sensor will immediately detect it and send a signal to this
heade r, and the system will then record this chass is intr usion event. e default setting is
set to the CASEOPEN and GND pin; this function is o.

D. Locator LED (4-pin LOCATOR)
is hea der is for the loc ator switch and LED on the front panel.

E. Syste m Fault LED (2-pin LOCATOR)
is hea der is for the Fault LED on the system.

A

B

is header supports multiple

functions on the front panel,

SMB _Aler t

SMB _CLK

1

+5V SB

CAS EOPEN

C

LAN 3_LIN K

+3V SB

GND

SMB _DATA

GND

LOC ATORBTN #

LOC ATORLED 1-

LOC ATORLED 1+

D

including the front panel SMB,

LED _PWR

LED _PWR

LAN 4_LIN K

internet status indicator and

chassis intrusion pin.

GND

E

Sys tem F ault LED+

Sys tem F ault LED-

Serial ATA3 DOM

Connector

(SATA_0)

(see p.7, No. 13)

SATA_0

e SATA3 DOM

connector supports

both a SATA DOM

(Disk-On-Module) and

a SATA data cable for

internal storage device.

English

Serial ATA3 Connectors

ID

Ver ti c a l:

(SATA_0:

see p.7, No. 13)

(SATA_1:

see p.7, No. 15)

(SATA_6:

see p.7, No. 21)

(SATA_7:

see p.7, No. 20)

Right Angle:

(SATA_2:

see p.7, No. 17)(Lower)

(SATA_3:

see p.7, No. 17)(Upper)

(SATA_4:

see p.7, No. 19)(Lower)

(SATA_5:

see p.7, No. 19)(Upper)

SATA_0

SATA_1

SATA_6

SATA_7

SATA_3

SATA_5

ese connectors

support SATA data

cables for internal

storage devices with up

to 6.0 Gb/s data transfer

rate.

SATA_2

SATA_4

USB 3.1 Gen1 Header

(19-pin USB3_3_4)

(see p.7, No. 14)

IntA_P_SSRX +

IntA_P_SSRX -

Vbu s

Vbu s

IntA_P_SSRX -

IntA_P_SSRX +

IntA_P_SSTX+

IntA_P_SSTX-

GN D

GN D

IntA_P_SSTX-

IntA_P_SSTX+

IntA_P_D +

IntA_P_D -

GN D

GN D

IntA_P_D -

IntA_P_D +

ere is one USB 3.1 Gen1

header on this motherboard.

is USB 3.1 Gen1 header

can support two USB 3.1 Gen1

ports.

1

English

30 31

X570D4U-2L2T / X570D4U

NC

48

System Fan Connectors

(4-p in FAN1)

(see p.7, No. 26)

(4- pi n FAN2)

(see p.7, No. 27)

(4- pi n FAN3)

(see p.7, No. 5)

(6-pin FAN4)

(see p.7, No. 6)

(6-pin FAN5)

(see p.7, No. 7)

(6-pin FAN6)

(see p.7, No. 9)

ATX Power Connector

(24-p in ATXPWR1)

(see p.7, No. 4)

ATX 12V Power

Connectors

(8-pin ATX12V3)

(see p.7, No. 1)

FAN_SPEED_CONTROL

FAN_VOLTAGE

FAN_SPEED_CONTROL

FAN_VOLTAGE

GND

3V

3V

5V

13

3V

-12V

GND

PSON#

FAN_SPEED

GND

1234

SENSOR

FAN_SPEED

GND

123456

PWROK_PS

GND

GND

5V

GND

GND

GND

N/A

GND

15

5VSB

12V

Please connect fan cables to the

fan connectors and match the

black wire to the ground pin.

All fans support Fan Control.

12V

is motherboard provides a

12V

3V

24-pin ATX power connector.

121

To use a 20-pin ATX power

supply, please plug it along Pin

24

5V5V5V

GND

1 and Pin 13.

is motherboard provides

one 8-pin ATX 12V power

connector.

TPM Header

(17-pi n TPM1)

(see p.7, No. 28)

SMB _D ATA_M AI N

SMB _C LK _MA IN

GND

S_P WR DW N#

LAD 1_ L

LAD 2_ L

GND

is connector supports

SER IR Q#

Trusted Platform Module

(TPM) system, which can

securely store keys, digital

certicates, passwords, and

1

LAD 3_ L

CK_ 33 M_ TPM

+3V

TPM _R ST #

LFR AM E# _L

LAD 0_ L

data. A TPM system also helps

GNDF_C LK RU N#

+3V SB

enhance network security,

protects digital identities, and

English

ensures platform integrity.

PSU SMBus Header

ALERT

IPMB_SDA

(5-pin PSU_SMB1)

(see p.7, No. 3)

SMBCLK

1

SMBDATA

GND

+3V

PSU SMBus monitors the

status of the power supply, fan

and system temperature.

Intelligent Platform

Management Bus Header

(4-pin IPMB_1)

(see p.7, No. 32)

Baseboard Management

Controller SMBus Header

(5-pin BMC_SMB_1)

(see p.7, No. 31)

Chassis Speaker Header

(4-p in SPEAKER1)

(see p.7, No. 30)

SATA DOM Power

Connector

(3-p in SATAPW R1)

(see p.7, No. 10)

GND
No Connect

Power

BMC_SMBCLK

GND

BMC_SMBDATA

DUMMY

1

+5V

GND

+5V

IPMB_SCL

BMC_SMB_PRESENT_1_N

SPEAKER

DUMMY

N/C

This 4-pin connector is used

to provide a cabled base-board

or front panel connection for

value added features and 3rd-

party add-in cards, such as

Emergency Management cards,

that provide management

features using the IPMB.

e header is used for the

SMBUS devices.

Please connect the chassis

speaker to this header.

Please connect the power cable

on the SATA DOM to this

connector.

English

SPI TPM Header

(13-pin TPM_BIOS_PH1)

(see p.7, No. 18)

SPI_DQ2

SPI_CS0

SPI_MISO

RSMRST#

SPI_TPM_CS#

GND

1

SPI_DQ3

+3.3V

TPM_Present

CLK

SPI_MOSI

RST#

TPM_PIRQ

is connector supports SPI

Trusted Platform Module

(TPM) system, which can

securely store keys, digital

certicates, passwords, and

data. A TPM system also helps

enhance network security,

protects digital identities, and

ensures platform integrity.

32 33

X570D4U-2L2T / X570D4U

1

LAN4_LINK

ermal Sensor Header

(3-pin TR1)

(see p.7, No. 22)

Front VGA Header

(15 -pi n FR NT_VGA 1)

(see p.7, No. 36)

Front LAN LED

Connector

(LED_LAN_3_4)

(see p.7, No. 35)

(X570D4U-2L 2T only)

Clear CMOS Pad

(CLRCMO S1)

(see p.7, No. 25)

Red

Blu e

GND

GND

+5V

H_S YNC

DDC _CL K

TR1 TR1

1

GND

LED_PWR

1

LAN3_LINK

LED_PWR

Gre en

GND

GND

GND

DDC _DA TA

V_S YNC

Please connect the thermal

sensor cable to either pin 1-2

or pin 2-3 and the other end to

the device which you wish to

monitor its temperature.

Please connect either end

of VGA_2X8 cable to VGA

header.

is 4-pin connector is used

for the front LAN status

indicator.

is allows you to clear the

data in CMOS. To clear CMOS,

take out the CMOS battery and

short the Clear CMOS Pad.

English

2.9 Dr. Debug

Dr. Debug is used to provide code information, which makes troubleshooting even

easier. Please see the diagrams below for reading the Dr. Debug codes.

Code Description

0x10 PEI_CORE _STARTED

0x11 PEI_CAR_CPU_INIT

0x15 PEI_CAR_NB_INIT

0x19 PEI_CAR_SB_INIT

0x 31 PEI_MEMORY_INSTALLED

0x32 PEI_CPU_INIT

0x33 PEI_CPU_CACHE_INIT

0x34 PEI_CPU_AP_INIT

0x35 PEI_CPU_BSP_SELECT

0x36 PEI_CPU_SMM_INIT

0x37 PEI_MEM_NB_INIT

0x3B PEI_MEM_SB_INIT

0x4F PEI_DXE_IPL_STARTED

English

0x60 DXE_CORE_STARTED

0x61 DXE_NVRAM_INIT

0x62 DXE_SBRU N_I NIT

34 35

0x63 DXE _CPU_ INIT

0x68 DXE_NB_HB_INIT

0x69 DXE_NB_INIT

0x6A DXE_NB_SMM_INIT

0x70 DXE_SB_INIT

0x71 DXE_SB_SMM_INIT

0x72 DXE_SB_DEVICES_INIT

0x78 DXE_ACPI_INIT

0x79 DXE_CSM_I NIT

X570D4U-2L2T / X570D4U

0x90 DXE_BDS_STARTED

0x91 DXE_BDS_CONNECT_DRIVERS

0x92 DXE_PCI_BUS_BEGIN

0x93 DXE_PCI_BUS_HPC_INIT

0x94 DXE_PCI_BUS_ENUM

0x95 DXE_PCI_BUS_REQUEST_RESOURCES

0x96 DXE_PCI_BUS_ASSIGN_RESOURCES

0x97 DXE_CON_OUT_CONNECT

0x98 DXE_CON_IN_CONNECT

English

0x99 DXE_SIO_I NIT

0x 9A DXE_USB_BEGIN

0x9B DX E_USB_R ESET

0x9C DXE_USB_DETECT

0x9D DXE_USB_ENABLE

0xA0 DXE_IDE_BEGIN

0xA1 DXE_IDE_RESET

0xA2 DXE _IDE_DETECT

0xA3 DXE_IDE_ENABLE

0xA4 DXE_SCSI_BEGIN

0xA5 DXE_SCSI_RESE T

0xA6 DXE_SCSI_DETECT

0xA7 DXE_SCSI_ENA BL E

0xA8 DXE_SET UP_VER IFY ING_PASSWORD

0xA9 DXE_SETUP_START

0xAB DXE_SETUP_INPUT_WAIT

English

0xAD DX E _REA DY_TO _BOOT

0xAE DXE_LEGACY_BOOT

36 37

X570D4U-2L2T / X570D4U

0xAF DX E _EX IT_BOOT_ SERVICES

0xB0 RT_SET_VIRTUAL_ADDRESS_MAP_BEGIN

0x B1 RT_SET_VIRTUAL_ADDRESS_MAP_END

0xB2 DX E _LEGACY_OPROM _INIT

0xB3 DXE _R ESET_SYSTEM

0xB4 DXE _USB_HOTPLUG

0xB5 DXE_PCI_BUS_HOTPLUG

0xB6 DXE_NVRAM_CLEANUP

0xB7 DXE_CONFIGUR ATION_RESET

0xF0 PE I _REC OV ERY_ AUTO

0xF1 PEI_RECOVERY_USER

0xF2 PEI_ RECOVERY_STA RTED

0xF3 PEI_RECOVERY_CAPSULE_FOUND

0xF4 PEI_RECOVERY_CAPSULE_LOADED

0xE0 PEI_S3_STARTED

0xE1 PEI_S3_BOOT_SCRIPT

0xE2 PEI_S3_VIDEO_REPOST

English

0xE3 PE I_ S3 _OS _WAK E

0x50 PEI_MEMORY_INVALID_TYPE

0x53 PEI_MEMORY_NOT_DETECTED

0x55 PEI_MEMORY_NOT_INSTALLED

0x57 PEI_CPU_MISMATCH

0x58 PEI_CPU_SELF_TEST_FAILED

0x59 PEI_CPU_NO_MICROCODE

0x5A PEI_CPU_ERROR

0x5B PEI_ RESET_NOT_ AVAILA BLE

0xD0 DXE_CPU_ERROR

0x D1 DXE_NB_ERROR

0xD2 DXE_SB_ERROR

0xD3 DXE_ARCH_PROTOCOL_NOT_AVAILABLE

0xD4 DXE_PCI_BUS_OUT_OF_RESOURCES

0xD5 DXE_L EGACY_OPROM _NO_SPACE

0xD6 DXE_NO_CON_OUT

English

0xD7 DXE_NO_CON_IN

38 39

0xD8 DX E _IN VALID_PASSWORD

0xD9 DXE_BOOT_OPTION_LOAD_ERROR

0x DA DXE_BOOT_OPTION_FAILED

0xDB DXE_FLASH_UPDATE_FAILED

0xDC DXE_R ESET_ NOT_AVAILABL E

0xE8 PEI_MEMORY_S3_RESUME_FAILED

0xE9 PEI_S3_RESUME_PPI_NOT_FOUND

0xEA PEI_ S3_BOOT_ SCRIPT_ ERROR

0xEB PEI_S3_OS_WAKE_ERROR

X570D4U-2L2T / X570D4U

English

2.10 Unit Identication purpose LED/Switch

With the UID button, You are able to locate the server you’re working on from behind

a rack of servers.

Unit Identication

purpose LED/Switch

(U ID1)

When the UID button on the

front or rear panel is pressed,

the front/rear UID blue LED

indicator will be truned on.

Press the UID button again to

turn o the indicator.

2.11 Driver Installation Guide

To install the drivers to your system, please insert the support CD to your optical

drive rst. en, the drivers compatible to your system can be auto-detected and listed

on the support CD driver page. Please follow the order from top to bottom to install

those required drivers. erefore, the drivers you install can work properly.

English

40 41

X570D4U-2L2T / X570D4U

2.12 M.2_SSD (NGFF) Module Installation Guide (M2_1)

The M.2, also known as the Next Generation Form Factor (NGFF), is a small size and

versatile card edge connector that a ims to replace mPCIe and mSATA. The M.2_ SSD

(NGFF) Socket 3 can accommodate either a M.2 SATA3 6.0 Gb/s module or a M.2 PCI

Express module up to Gen4 x4 (64Gb/s) (Matisse) or Gen3 x4 (32Gb/s) (Picasso).

Installingg the M.2_SSD (NGFF) Module

Step 1

Prepare a M.2_SSD (NGFF) module

and the screw.

4

3

Step 2

Depending on the PCB type and

length of your M.2_SSD (NGFF)

module, nd the corresponding nut

2

1

A

BCD

location to be used.

No. 1 2 3 4

Nut Location A B C D

PCB Length 4.2cm 6cm 8cm 10cm

Module Type Typ e 22 42 Ty pe2260 Ty pe 22 80 Typ e 22110

English

Step 3

Move the stando based on the

module type and length.

e stando is placed at the nut

A

BCD

location C by default. Skip Step 3

and 4 and go straight to Step 5 if you

are going to use the default nut.

Otherwise, release the stando by

hand.

Step 4

Peel o the yellow protective lm on

the nut to be used. Hand tighten the

A

BCD

stando into the desired nut location

on the motherboard.

Step 5

Align and gently insert the M.2

(NGFF) SSD module into the M.2

ABCD

slot. Please be aware that the M.2

(NGFF) SSD module only ts in one

orientation.

ABCD

o

20

Step 6

Tighten the screw with a screwdriver

to secure the module into place.

CD

NUT1NUT2

Please do not overtighten the screw

as this might damage the module.

English

For the latest updates of M.2_SSD (NFGG) module support list, please visit our website for

details: http://www.asrockrack.com

42 43

X570D4U-2L2T / X570D4U

2.13 M.2_SSD (NGFF) Module Installation Guide (M2_2)

The M.2, also known as the Next Generation Form Factor (NGFF), is a small size and

versatile card edge connector that a ims to replace mPCIe and mSATA. The M.2_ SSD

(NGFF) Socket 3 can accommodate either a M.2 SATA3 6.0 Gb/s module or a M.2 PCI

Express module up to Gen4 x4 (64Gb/s) (Matisse) or Gen3 x4 (32Gb/s) (Picasso).

Installingg the M.2_SSD (NGFF) Module

Step 1

Prepare a M.2_SSD (NGFF) module

and the screw.

3

2

1

1

ABC

No. 1 2 3

Nut Location A B C

PCB Length 4.2cm 6cm 8cm

Module Type Typ e 22 42 Ty pe2260 Ty pe 22 80

Step 2

Depending on the PCB type and

length of your M.2_SSD (NGFF)

module, nd the corresponding nut

location to be used.

English

Step 3

Move the stando based on the

module type and length.

e stando is placed at the nut

location C by default. Skip Step 3

A

BC

and 4 and go straight to Step 5 if you

are going to use the default nut.

Otherwise, release the stando by

hand.

Step 4

Peel o the yellow protective lm on

A

BC

the nut to be used. Hand tighten the

stando into the desired nut location

on the motherboard.

Step 5

Align and gently insert the M.2

(NGFF) SSD module into the M.2

slot. Please be aware that the M.2

ABC

(NGFF) SSD module only ts in one

orientation.

ABC

o

20

Step 6

Tighten the screw with a screwdriver

to secure the module into place.

C

English

NUT1NUT2

Please do not overtighten the screw

as this might damage the module.

For the latest updates of M.2_SSD (NFGG) module support list, please visit our website for

details: http://www.asrockrack.com

44 45