X570D4I-2T
User Manual
Version 1.0
Published February 2020
Copyright©2020 ASRock Rack INC. All rights reserved.
X570D4I-2T
Chapter 1 Introduction
ank you for purchasing ASRock Rack X570D4I-2T motherboard, a reliable
motherboard produced under ASRock Rack’s consistently stringent quality control.
It delivers excellent performance with robust design conforming to ASRock Rack’s
commitment to quality and endurance.
In this manual, chapter 1 and 2 contains introduction of the motherboard and step-
by-step guide to the hardware installation. Chapter 3 and 4 contains the conguration
guide to BIOS setup and information of the Support CD.
Becau se the motherboard specications and the BIOS soware might be updated, the content of thi s manual will be subject to change without notice. In case any modications of
this manual occ ur, the updated version will be available on ASRock Rack website without
further notice. You may nd the lates t memor y and CPU support lists on ASRock Rack
website a s well. ASRock Rack’s Website: www.ASRockRack.com
If you require technical support related to this motherboard , please visit our website for
specic information about the model you are using.
http://www.asrockrack.com/support/
1.1 Package Contents
ASRock Rack X570D4I-2T Motherboard
•
(Mini ITX Form Factor: 6.7-in x 6.7-in, 17.02 cm x17.02 cm)
1 x SATA Power Cable (80cm)
•
1 x ATX 4P to 24P Power Cable
•
1 x I/O Shield
•
1 x Screw for M.2 Socket
•
Quick Installation Guide
•
If any items are miss ing or appear dam aged, contact your authorized dealer.
English
English
1.2 Specications
X570D4I-2T
MB Physical Status
Form Factor Mini ITX
Dimension 6.7'' x 6.7'' (17.02cm x17.02 cm)
Processor System
CPU AMD Ryzen™ 3rd Generation Series Processors*
*We recommend using the CPU HS listed in the Cooler QVL section on our
ASRock Rack website.
Chipset AMD X570
System Memory
Capacity 4 x DDR4 DIMM slots
Type - Dual Channel memory technolog y, 2DPC
- 4 x 260-pin DDR4 ECC/SO-DIMM slots
DIMM Size Per
DIMM
DIMM
Frequency
Vol t a ge 1.2V
Expansion Slot
PCIe 4.0/3.0 x16 1 slot
Storage
SATA
Controller
M.2 1 M.2 M-key(NGFF 2280) (1 SATA 6Gb/s or PCIe4.0/3.0 x4)
Ethernet
Interface 10000/1000 /100 Mbps
LAN - 2 x RJ45 10G base-T by Intel® X550-AT2
Graphics
Controller ASPEED AST2500
VRAM 16MB DDR4
Rear Panel I/O
VGA Port 1 x D-Sub
USB 3.0 Port 2
LAN Port - RJ45: 2x 10GLAN(by Intel® X550-AT2)
ECC/SO-DIMM: 32GB, 16GB, 8GB, 4GB
ECC/SO-DIMM: 2933/2666/2400/2133/1866 MHz
AMD X570: 2x OCULINK (support 4x SATA or PCIEx4 from
OCU1, 4x SATA or PCIEx4 from OCU2)
- 1 x RJ45 Dedicated IPMI LAN port by RTL8211E
- Supports Wake-On-LAN
- Supports Energy Ecient Ethernet 802.3az
- Supports Dual LAN with Teaming function
- Supports PXE
- LAN1 supports NCSI
- LAN Ports with LED (ACT/LINK LED and SPEED LED)
2 3
X570D4I-2T
Management
LAN Port
UID 1
Internal Connector
ITX_AUX_
PANEL1
PANEL1 1
TR1 1
TPM Header 1
Fan Header 3x (4-pin)
ATX power DC-IN1x (8-pin)
4 to 24P Power 1x (4-pi n)
SATA Power 1x (4 -pin)
OCuLink 2
USB 3.0 Header 1 (supports 2 USB3.0)
ClearCMOS 1 (short pad)
COM Header 1
IPMB 1
PWR SMB 1
BMC_SMB 1
NCSI1 1
OH/FanFail
LED
System BIOS
BI O S Ty pe 256Mb AMI UEFI Legal BIOS
BIOS Features - Plug and Play (PnP)
Hardware Monitor
Temperature - CPU/PCH/DDR/LAN/Storage Temperature Sensing
Fan - CPU/Rear/Front Fan Tachometer
1
1
3
- ACPI 2.0 Compliance Wake Up Events
- SMBIOS 2.8.0 Support
- ASRock Rack Instant Flash
- MB/Card side/TR1 Temperature Sensing
- CPU Quiet Fan (Allow Chassis Fan Speed Auto-Adjust by
CPU Temperature)
- CPU/Rear/Front Fan Multi-Speed Control
English
Vol t a ge Voltage Monitoring: 3VSB, 5VSB, VCPU, VSOC, VCCM, APU
VDDP, PM VDD CLDO, PM VDDCR S5, PM VDDCR, BAT,
3V, 5V, 12V
Support OS
OS Microso® Windows®
- Server 2016 (64 bit)
- Server 2019 (64 bit)
Linux®
- RedHat Enterprise Linux Server 6.10 (64 bit) / 7.5 (64 bit)
- SUSE Enterprise Linux Server 11 SP4 (64 bit) / 12 SP3 (64 bit)
- Ubuntu 16.04 (64 bit)/ 18.04 (64 bit)
Virtual
- VMWare® ESXi 6.5 u1
- Win hyper-V Server 2016
* Please refer to our website for the latest OS support list.
Environment
Temperature Operation temperature: 10°C ~ 35°C / Non operation
temperature: -40°C ~ 70°C
is motherboard suppor ts Wake from on Board LAN. To use this func tion, please make
NOTE: Please refer to our website for the latest specications.
sure that the “Wake on Magic Packet from power o state” is enabled in Device Manager
> Intel® Ethernet Connec tion > Power Manage ment. And the “PCI Devices Power On” is
enabled in UEFI SETUP UT ILITY > Advanced > ACPI Conguration. Aer that, onboard
LAN1&2 can wake up S5 under OS.
If you install Intel® LAN utility or Marvell S ATA utility, this motherboard may fail Windows® Hardware Quality Lab (WHQL) certi cation tests. If you install the drivers only, it
will pa ss the WHQL tests.
English
4 5
1.3 Unique Features
ASRock Rack Instant Flash is a BIOS ash utility embedded in Flash ROM. is con-
venient BIOS update tool allows you to update system BIOS without entering operat-
ing systems rst like MS-DOS or Windows®. With this utility, you can press the <F6>
key during the POST or the <F2> key to enter into the BIOS setup menu to access
ASRock Rack Instant Flash. Just launch this tool and save the new BIOS le to your
USB ash drive, oppy disk or hard drive, then you can update your BIOS only in a
few clicks without preparing an additional oppy diskette or other complicated ash
utility. Please be noted that the USB ash drive or hard drive must use FAT32/16/12
le system.
X570D4I-2T
English
1.4 Motherboard Layout
PCIE7
17.0cm (6.7 in)
17. 0cm (6. 7 in)
VGA1
USB 3.0
T: USB_1
B: USB_2
USB3_3_4
X570D4I-2T
CLRMOS1
3
ATX12V2
COM1
1
OCU2
C 1
M2_1
T
CMOS Battery
BMC
1
2
19
17
16
7
5
24
20
21
TPM1
1
T 1
R
1
1
PWM_CFG1
23
22
1
PSU_SMB1
1
24
UID1
IPMI_LAN
DDR4_A2 (64 bit, 260-pin module)
DDR4_A1 (64 bit, 260-pin module)
DDR4_B2 (64 bit, 260-pin module)
DDR4_B1 (64 bit, 260-pin module)
ATX4PIN1
SATAPWR1
1
OCU1
1
BMC_SMB_1
IPMB_1
LAN1
LAN2
(NCSI)
X550
1
NCSI1
FAN2
4
ITX_AUX_PANEL1
1
AMD
X570
FAN1
FAN3
HDLED RESET
PLED PWRBTN
PANEL1
1
1
SPEAKER1
1
CHASSIS_ID1
BIOS
ROM
6
8
11
9
10
14
12
13
15
18
English
6 7
No. Description
1 2 x 260-pin DDR4 SO-DIMM Slots (DDR4_A2, DDR4_B2)
2 2 x 260-pin DDR4 SO-DIMM Slots (DDR4_A1, DDR4_B1)
3 4 to 24P Power Connector (ATX4PIN1)
4 ATX 12V Power Connector (ATX12V2)
5 PSU SMBus (PSU_SMB1)
6 ermal Sensor Header (TR1)
7 TPM Header (TPM1)
8 System Fan Connector (FAN1)
9 OCuLink x4 Connector (OCU1)
10 USB 3.0 Header (USB3_3_4)
11 OCuLink x4 Connector (OCU2)
12 System Fan Connector (FAN2)
13 System Fan Connector (FAN3)
14 SATA Power Connector (SATAPWR1)
15 System Panel Header (PANEL1)
16 Speaker Header (SPEAKER1)
17 Auxiliar y Panel Header (ITX_AUX_PANEL1)
18 Clear CMOS Pad (CLRMOS1)
19 Chassis ID Jumper (CHASSIS_ID1)
20 PWM Conguration Header (PWM_CFG1)
21 BMC SMBus Header (BMC_SMB_1)
22 Intelligent Platform Management Bus header (IPMB_1)
23 COM Port Header (COM1)
24 M.2 Socket (M2_1) (Type 2280)
25 NCSI Header (NCSI1)
X570D4I-2T
English
1.5 Onboard LED Indicators
X570D4I-2T
1
DDR4_A2 (64 bit, 260-pin module)
DDR4_A1 (64 bit, 260-pin module)
DDR4_B2 (64 bit, 260-pin module)
DDR4_B1 (64 bit, 260-pin module)
1
1
AMD
X570
HDLED RESET
PLED PWRBTN
1
1
1
1
3
4
2
5
No. Item Status Description
1 SB_PWR1_LED Green STB PWR ready
2 LED_ FAN1 Amber FAN1 failed
3 LED_ FAN2 Amber FAN2 failed
4 LED_ FAN3 Amber FAN3 failed
5 BMC_LE D1 Green BMC heartbeat LED
English
8 9
1.6 I/O Panel
2
4
X570D4I-2T
1
No. Description No. Description
1 USB 3.0 Ports (USB3_1_2) 4 10G LAN RJ-45 Port (LAN2)**
2 LAN RJ-45 Port (IPMI_LAN)* 5 VGA Por t ( VGA1)
3 10G LAN RJ-45 Port (LAN1)** 6 UID Switch (UID1)
LAN Port LED Indications
*ere are two LEDs on each LAN port. Please refer to the table below for the LAN port
LED indications.
ACT/LINK LED
SPEED LED
LAN Por t
Dedicated IPMI LAN Port LED Indications
Activity / Link LED Speed LED
Status Description Status Description
O No Link O 10Mbps connection or
Blinking Yellow Data Activity Yel low 100Mbps connection
On Link Green 1Gbps connection
5
63
no link
English
**ere are two LEDs on each LAN port. Please refer to the table below for the LAN port
LED indications.
ACT/LINK LE D
ACT/LINK LE D
LAN Port
SPEED LE D
SPEED LE D
10G LAN Port (LAN1, LAN2) LED Indications
Activity / Link LED Speed LED
Status Description Status Description
O No Link O 10M/100Mbps
connection or no link
Blinking Yellow Data Activity Orange 1Gbps connection
On Link Green 10Gbps connection
English
10 11
1.7 Block Diagram
X570D4I-2T
D-Sub
RTL
COM2 He ader
8211E
SO-DIMM
IPMI
B
A
DDR4
AMD Ryzen™
2xUSB3.1 Gen 2
2xUSB2.0
DDR4
Processor
PGA 1331
3nd Generation
AMD AM4 Socket
PCIe4.0x16
NCSI
TDP: max. 105W
PCIe4.0 x4/SATAIII
RGMII
VGA
PCIeUSB
MAC
UAR T
MAC
ASPEED
AST2500
BIOS
LPC
-AT2
X550
32MB
NCT6796D-R
LPC/eSPI
Upstream Li nk
PCIe4.0x4
2xUSB3.1 Gen1
2xUSB2.0
4x SAT AIII/PCIe4.0 x4
PCIe3.0x4
USB2.0
PCIe2.0 x1
X570
AMD
BXB-C
4x SAT AIII/PCIe4.0 x4
SPI
Swit ch
SLOT 7 x16
English
Chapter 2 Installation
This is a mini ITX form factor (6.7'' x 6.7'', 17.02 cm x 17.02 cm) motherboard. Before
you install the motherboard, study the cong uration of your chassis to ensure that t he
motherboard ts into it.
Make sure to unplug the power cord before installing or removing the mothe rboard . Failure
to do so may cause physical injuries to you and d amages to motherboard components.
2.1 Screw Holes
Place screws into the holes indicated by circles to secure the motherboard to the chassis.
Do not over-tighten the screws! Doing so may damage the motherboard.
2.2 Pre-installation Precautions
Take note of the following precautions before you insta ll motherboard components or
change any motherboard settings.
1. Unplug the power cord from the wall socket before touching any components.
2. To avoid damaging the motherboard ’s components due to static electricity, NEVER
place your motherboard directly on the carpet or the like. Also remember to use a
grounded wrist strap or touch a safety grounded object before you handle the compo-
nents.
3. Hold components by the edges and do not touch the ICs.
4. Whenever you uninstall any component, place it on a grounded anti-static pad or in
the bag that comes with the component.
5. When placing screws into the screw holes to secure the motherboard to the chassis,
please do not over-tighten the screws! Doing so may damage the motherboard.
Before you install or remove any component, ensure that the power is switched o or the
power cord is detached f rom the power supply. Failure to do so may cau se severe damage to
the motherboard, peripherals, and/or components.
English
12 13
2.3 Installing the CPU
Unplug all power cables be fore ins talling the CPU.
1
90
X570D4I-2T
o
2
English
3
2.4 Installing the CPU Fan and Heatsink
English
14 15
2.5 Installation of Memory Modules (DIMM)
is motherboard provides four 260-pin DDR4 (Double Data Rate 4) DIMM slots.
A single memory module should be installed in the A1 or B1 socket.
Two memory modules should be installed in the A1+B1, A1+A2, or B1+B2 sockets.
Priority A1 A2 B1 B2
1 DIMM
1
2
1
2 DIMMS
2
3
4 DIMMS
1. It is not allowed to install a DDR, DDR2 or DDR 3 memory modul e into a DDR4 slot;
otherwise, this motherboard and DIMM may be dam aged.
2. e DIMM only ts in one correct orientation. It will cause permanent damage to the
motherboard and the DIMM if you force the DIMM into the slot at incorrect orientation.
1
Populated
Populated
Populated Populated
Populated Populated
Populated Populated
Populated Populated Populated Populated
X570D4I-2T
English
1
2
3
English
16 17
2.6 Expansion Slot (PCI Express Slot)
ere is a PCI Express slot on this motherboard.
X570D4I-2T
PCIE slot:
PCIE7 (PCIe 3.0/4.0 x16 slot) is used for PCI Express x16 lane width cards.
Slot Generation Mechanical Electrical Source
PCIE 7 3.0/4.0 x16 x16 CPU
Installing an expansion card
Step 1. Before installing an expansion card, please make sure that the power
supply is switched o or the power cord is unplugged. Please read the
documentation of the expansion card and make necessary hardware
settings for the card before you start the installation.
Step 2. Remove the system unit cover (if your motherboard is already installed
in a chassis).
Step 3. Remove the bracket facing the slot that you intend to use. Keep the
screws for later use.
Step 4. Align the card connector with the slot and press rmly until the card is
completely seated on the slot.
Step 5. Fasten the card to the chassis with screws.
Step 6. Replace the system cover.
English
2.7 Jumper Setup
e illustration shows how jumpers are setup. When the jumper cap is placed on
the pins, the jumper is “Short”. If no jumper cap is placed on the pins, the jumper
is “Open”. e illustration shows a 3-pin jumper whose pin1 and pin2 are “Short”
when a jumper cap is placed on these 2 pins.
CHASSIS ID Jumper
(3-pin CHAS SIS _ID1)
(see p.6, No. 19)
Board Level SKU (Default) Reserved for system level
use
English
18 19
2.8 Onboard Headers and Connectors
Onboard headers and connectors are NOT jumpers. Do NOT place jumper caps over th ese
heade rs and connectors. Placing jumper caps o ver the headers and connectors will cause
permanent damage to the motherboard.
X570D4I-2T
System Panel Header
(9-pi n PANEL1)
(see p.6, No. 15)
PWRBTN (Power Switch):
Connec t to the power switch on the chassi s front panel. You may congure the way to tur n
o your system using the power switch.
RESET (Reset Switch):
Connec t to the reset switch on the chassi s front panel. Press the reset sw itch to restart the
computer if the computer f reezes and fails to per form a normal restar t.
PLED (Syste m Power LED):
Connec t to the power status indicator on th e chassis front panel . e LED is on when the
system is operating. e LED is o when the syste m is in S4 sleep state or powered o (S5).
HDLED (Ha rd Drive Activity LED):
Connec t to the hard drive ac tivity LED on the chassis front panel. e LED is on when the
hard drive is reading or wr iting data.
e front panel de sign may dier by chass is. A front panel module m ainly consist s of power
switch, reset switch , power LED, hard dr ive activity LED, speaker and etc. When connecting your ch assi s front panel module to thi s header, make sure the wire a ssignments and the
pin assignments are matched correctly.
1
PLED+
PLED-
HDLED-
HDLED+
PWRBTN#
GND
GND
RESET#
GND
Co n nec t t h e power sw i tch,
reset switch and system status
indicator on the chassis to this
he ade r acco rdin g to the pi n
assignments. Particularly note
the positive and negative pins
before connecting the cables.
Auxiliary Panel Header
(9-pin
ITX_AUX_PANEL1)
(see p.6, No. 17)
LAN1_ACT#
LED_PWR
LED_PWR
1
SYSTEM_FAULT_LED_N
GND
CASEOPEN#
LAN2_ACT#
SYSTEM_FAULT_LED_P
is header supports multiple
functions on the front panel,
including front panel SMB,
internet status indicator.
English
4 to 24P Power Connector
GND
FAN_VOLTAGE_CONTROL
FAN_SPEED
FAN_SPEED_CONTROL
(4-pin ATX4PIN1)
(see p.6, No. 3)
ATX_PG+5VSB
3
1
is motherboard provides
a 4-pin 4 to 24P power
4
2
GNDPSON#
connector.
SATA Power Connector
(4-pin SATAPWR1)
(see p.6, No. 14)
USB 3.0 Header
(19-pin USB3_3_4)
(see p.6, No. 10)
System Fan Connectors
(4-p in FAN1)
(see p.6, No. 8)
(4- pi n FAN2)
(see p.6, No. 12)
(4- pi n FAN3)
(see p.6, No. 13)
1
GND
+12V
IntA_PA_D+
IntA_PA_D-
Dummy
IntA_PB_D+
1 2
3 4
IntA_PA_SSTX+
IntA_PA_SSTX-
GND
GND
IntA_PB_D-
IntA_PB_SSTX+
GND
+5V
IntA_PA_SSRX+
IntA_PA_SSRX-
Vbus
GND
IntA_PB_SSTX-
GND
IntA_PB_SSRX+
IntA_PB_SSRX-
Please use a SATA power cable
to connect this SATA Power
Connector and your SATA
HDD for supplying power
from the motherboard, when
using DC _IN mode without
SATA power supply.
Be sid es two d efa ult U SB 3.0
por ts on the I/O panel, there
is one USB 3.0 header on this
mot her board . T his USB 3. 0
VbusVbus
header can support t wo USB
3.0 ports.
Please connect fan cables to the
fan con nector and match t he
black wire to the ground pin.
All fans support Fan Control.
ATX 12V Power
Connector
(8-pin ATX12V2)
(see p.6, No. 4)
GND
1
5
4
8
12V
is motherboard provides
one 8-pin ATX 12V power
connector.
English
20 21
TPM Header
GND
1
(13 -pi n TPM1)
(see p.6, No. 7)
+3V
+3V
+3V
GND
GND
LAD2
LAD3
LAD0
LAD1
RST
LFRAME
GND33M
is connector supports
Trusted Platform Module
1
(TPM) system, which can
securely store keys, digital
certicates, passwords, and
data. A TPM system also helps
enhance network security,
protects digital identities, and
ensures platform integrity.
X570D4I-2T
ermal Sensor Header
(3-pin TR1)
(see p.6, No. 6)
PWM Conguration
Header
(3-p in PW M _CF G1)
(see p.6, No. 20)
OCuLink Connectors
(OCU1)
(see p.6, No.9)
(OCU2)
(see p.6, No. 11)
Serial Port Header
(9-p in COM1)
(see p.6, No. 23)
DDCD#1
TTXD1
1
SMB_DATA_VSB
1
GND
RRTS#1
RRI#1
TR1 TR1
GND
SMB_CLK_VSB
OCU1
OCU2
DDSR#1
CCTS#
Please connect the thermal
sensor cable to either pin 1-2
or pin 2-3 and the other end to
the device which you wish to
monitor its temperature.
is header is used for PWM
congurations.
Please connect PCIE SSDs or
OCulink-to-SATA x4 cable to
the connectors.
is COM header supports a
RRXD1
DDTR#1
serial port module.
Clear CMOS Pad
(CLRMO S1)
(see p.6, No. 18)
CLRMOS1 allows you to clear
the data in CMOS. To clear
CMOS, take out the CMOS
battery and short the Clear
CMOS Pad.
English
Chassis Speaker Header
1
IPMB_SDA
(4-p in SPEAKER1)
(see p.6, No. 16)
DUMMY
1
+5V
SPEAKER
DUMMY
Please connect the chassis
speaker to this header.
PSU SMBus
(P SU_ SMB1)
(see p.6, No. 5)
Intelligent Platform
Management Bus Header
(4-pin IPMB_1)
(see p.6, No. 22)
Baseboard Management
Controller SMBus Header
(5-pin BMC_SMB_1)
(see p.6, No. 21)
NCSI Header
(9-pin NCSI1)
(see p.6, No. 25)
SMBCLK
SMBDATA
ALERT
GND
+3VSB
IPMB_SCL
GND
No Connect
BMC_SMB_PRESENT_1_N
Power
BMC_SMBCLK7
GND
GND
RXD1
RXD0
CRS_DV
BMC_SMBDATA7
CLK_IN
GND
TXD1
TXD0
TX Enable
1
PSU SMBus monitors the
status of the power supply, fan
and system temperature.
This 4-pin connector is used
to provide a cabled base-board
or front panel connection for
value added features and 3rd-
party add-in cards, such as
Emergency Management cards,
that provide management
features using the IPMB.
e header is used for the SM
BUS devices.
e onboard NCSI header is
used for external connections.
English
22 23
X570D4I-2T
2.9 Unit Identication purpose LED/Switch
With the UID button, You are able to locate the server you’re working on from behind
a rack of servers.
Unit Identication
purpose LED/Switch
(U ID1)
When the UID button on the
front or rear panel is pressed,
the front/rear UID blue LED
indicator will be turned on.
Press the UID button again to
turn o the indicator.
2.10 Driver Installation Guide
To install the drivers to your system, please insert the support CD to your optical
drive rst. en, the drivers compatible to your system can be auto-detected and listed
on the support CD driver page. Please follow the order from top to bottom to install
those required drivers. erefore, the drivers you install can work properly.
English
2.11 Dual LAN and Teaming Operation Guide
Dual LAN with Teaming enabled on this motherboard allows two single
connections to act as one single connection for twice the transmission bandwidth,
making data transmission more eective and improving the quality of transmission
of distant images. Fault tolerance on the dual LAN network prevents network
downtime by transferring the workload from a failed port to a working port.
e speed of transmission is subject to the actual network environment or status e ven with
Teaming enabled.
Before setting up Teaming, please make sure whether your Switch (or Router)
supports Teaming (IEEE 802.3ad Link Aggregation). You can specify a preferred
adapter in Intel PROSet. Under normal conditions, the Primary adapter handles all
non-TCP/IP trac. e Secondary adapter will receive fallback trac if the primary
fails. If the Preferred Primary adapter fails, but is later restored to an active status,
control is automatically switched back to the Preferred Primary adapter.
Step 1
From Device Manager, open the properties of a team.
Step 2
Click the Settings tab.
Step 3
Click the Modif y Team button.
Step 4
Select the adapter you want to be the primary adapter and click the Set Primary
button.
If you do not specify a preferred primary adapter, the soware will choose an
adapter of the highest capability (model and speed) to act as the default primary. If
a failover occurs, another adapter becomes the primary. e adapter will, however,
rejoin the team as a non-primary.
English
24 25
X570D4I-2T
2.12 M.2_SSD (NGFF) Module Installation Guide (M2_1)
The M.2, also known as the Next Generation Form Factor (NGFF), is a small size and
versatile ca rd edge connector that aims to replace mPCIe and mSATA. T his M.2 _SSD
(NGFF) Socket 3 can accommodate a SATA3 6.0 Gb/s module or a PCI Express module up
to Gen4 x4 (64 Gb/s) only.
Installing the M.2_SSD (NGFF) Module
Step 1
Prepare a M.2_SSD (NGFF) module
and the screw.
Step 2
Gently insert the M.2 (NGFF) SSD
module into the M.2 slot. Please
o
20
be aware that the M.2 (NGFF) SSD
module only ts in one orientation.
Step 3
Tighten the screw with a screwdriver
to secure the module into place.
Please do not overtighten the screw as
NUT1NUT2
this might damage the module.
M.2_SSD (NGFF) Module Support List
For the latest updates of M.2_SSD (NFGG) module support list, please visit our website for
details: http://www.asrockrack.com
English
Loading...