No part of this documentation may be reproduced, transcribed, transmitted, or
translated in any language, in any form or by any means, except duplication of
documentation by the purchaser for backup purpose, without written consent of
ASRock Inc.
Products and corporate names appearing in this documentation may or may not
be registered trademarks or copyrights of their respective companies, and are used
only for identication or explanation and to the owners’ benet, without intent to
infringe.
Disclaimer:
Specications and information contained in this documentation are furnished for
informational use only and subject to change without notice, and should not be
constructed as a commitment by ASRock. ASRock assumes no responsibility for
any errors or omissions that may appear in this documentation.
With respect to the contents of this documentation, ASRock does not provide
warranty of any kind, either expressed or implied, including but not limited to
the implied warranties or conditions of merchantability or tness for a particular
purpose.
In no event shall ASRock, its directors, ocers, employees, or agents be liable for
any indirect, special, incidental, or consequential damages (including damages for
loss of prots, loss of business, loss of data, interruption of business and the like),
even if ASRock has been advised of the possibility of such damages arising from any
defect or error in the documentation or product.
is device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
CALIFORNIA, USA ONLY
e Lithium battery adopted on this motherboard contains Perchlorate, a toxic substance
controlled in Perchlorate Best Management Practices (BMP) regulations passed by the
California Legislature. When you discard the Lithium battery in California, USA, please
follow the related regulations in advance.
“Perchlorate Material-special handling may apply, see www.dtsc.ca.gov/hazardouswaste/
perchlorate”
ASRock Website: http://www.asrock.com
Page 2
e terms HDMI™ and HDMI High-Denition Multimedia Interface, and the HDMI
logo are trademarks or registered trademarks of HDMI Licensing LLC in the United
States and other countries.
** If you use a 2- channel speaker, plea se connect the speake r’s plug into “Front Speaker Jack”. See the table below
for connection d etails in accordance w ith the type of speaker you use.
English
Audio Output
Channels
Front Speaker
(No. 9)
Rear Speaker
(No. 7)
Central / Bass
(No. 6)
2V------
4VV----
6VVV--
8VVVV
To enable Multi-Streaming, you need to connect a front panel audio cable to the front
panel audio header. Aer restarting your computer, you will nd the “Mixer” tool on your
system. Please select “Mixe r ToolBox” , click “Enable playback multi-streaming”, and
click “ok”. Choose “2CH”, “4CH”, “6CH”, or “8CH” and then you are allowed to select
“Realtek HDA Primary output” to u se the Rear Speaker, Central/Bass, and Front Speaker,
or select “Realtek HDA Audio 2nd output” to use the front panel audio.
*** e eSATA connector supports SATA3 with cables within 1 meters.
Line In
(No. 8)
4PB
Page 7
Chapter 1 Introduction
ank you for purchasing ASRock Z87M OC Formula motherboard, a reliable
motherboard produced under ASRock’s consistently stringent quality control.
It delivers excellent performance with robust design conforming to ASRock’s
commitment to quality and endurance.
Becau se the motherboard specications and the BIOS soware might be updated, the
content of this documentation will be subject to change without notice. In case any modications of this documentation occur, the updated version will be available on ASRock’s
website w ithout further notice. If you require technical support related to this motherboard, please visit our website for specic information about the model you are using. You
may nd the l atest VGA cards and CPU suppor t list on ASRock’s website a s well. ASRock
website http://www.asrock.com.
1.1 Package Contents
ASRock Z87M OC Formula Motherboard (Micro ATX Form Factor)
2 x PCI Express 3.0 x16 slots (PCIE1/PCIE3: single at x16
•
(PCIE1); dual at x8 (PCIE1) / x8 (PCIE3))
1 x PCI Express 2.0 x4 slot
•
1 x PCI Express 2.0 x1 slot
•
1 x half mini-PCI Express slot
•
1 x mSATA/mini-PCI Express slot
•
* mSATA/mini-PCI Express slot is shared with the SATA3_4
port.
Supports AMD Quad CrossFireXTM and CrossFireXTM
•
Supports NVIDIA® Quad SLITM and SLI
•
TM
Z87M OC Formula
Graphics
Intel® HD Graphics Built-in Visuals and the VGA outputs can
•
be supported only with processors which are GPU integrated.
Supports Intel® HD Graphics Built-in Visuals : Intel® Quick
•
Sync Video with AVC, MVC (S3D) and MPEG-2 Full
HW Encode1, Intel® InTruTM 3D, Intel® Clear Video HD
Technology, Intel® InsiderTM, Intel® HD Graphics 4400/4600
Pixel Shader 5.0, DirectX 11.1
•
Max. shared memory 1792MB
•
Dual VGA Output: support HDMI and DisplayPort ports by
•
independent display controllers
Supports HDMI Technology with max. resolution up to 4K x
•
2K (4096x2304) @ 24Hz
Supports DisplayPort with max. resolution up to 4K x 2K
•
(4096x2304) @ 24Hz
Supports Auto Lip Sync, Deep Color (12bpc), xvYCC and
•
HBR (High Bit Rate Audio) with HDMI (Compliant HDMI
monitor is required)
Supports HDCP function with HDMI and DisplayPort ports
•
Supports Full HD 1080p Blu-ray (BD) playback with HDMI
•
and DisplayPort ports
English
Page 10
Audio
LAN
Rear Panel
I/O
7.1 CH HD Audio with Content Protection (Realtek ALC1150
•
Aud io Codec)
Premium Blu-ray audio support
•
Supports Purity Sound ™
•
- 115dB SNR DAC with dierential amplier
- TI® NE5532 Premium Headset Amplier (supports up to
600 Ohms headsets)
- Direct Drive Technology
- EMI shielding cover
- PCB isolate shielding
Supports DTS Connect
•
Gigabit LAN 10/100/1000 Mb/s
•
Giga PHY Intel® I217V
•
Supports Intell® Remote Wake Technology
•
Supports Wake-On-LAN
•
Supports Energy Ecient Ethernet 802.3az
•
Supports PXE
•
1 x PS/2 Mouse/Keyboard Port
•
1 x HDMI-Out Port
•
1 x HDMI-In Port
•
1 x DisplayPort
•
1 x Optical SPDIF Out Port
•
1 x eSATA Connector
•
2 x USB 2.0 Ports
•
4 x USB 3.0 Ports (Intel® Z87) (ASMedia Hub)
•
2 x USB 3.0 Ports (Intel® Z87)
•
1 x RJ-45 LAN Port with LED (ACT/LINK LED and SPEED
•
LED)
1 x Clear CMOS Button
•
HD Audio Jack: Rear Speaker / Central / Bass / Line in / Front
•
Speaker / Microphone
English
89
Page 11
Storage
Connector
Z87M OC Formula
6 x SATA3 6.0 Gb/s connectors, support RAID (RAID 0,
•
RAID 1, RAID 5, RAID 10, Intel Rapid Storage Technology
12 and Intel Smart Response Technology), NCQ, AHCI and
Hot Plug
1 x eSATA connector, support RAID (RAID 0, RAID 1,
•
RAID 5, RAID 10, Intel Rapid Storage Technology 12 and
Intel Smart Response Technology), NCQ, AHCI and Hot Plug
* eSATA Connector is shared with the SATA3_1 port.
1 x IR header
•
1 x COM port header
•
1 x Power LED header
•
2 x CPU Fan connectors (1 x 4-pin, 1 x 3-pin)
•
3 x Chassis Fan connectors (1 x 4-pin, 2 x 3-pin)
•
1 x Power Fan connector (3-pin)
•
1 x 24 pin ATX power connector
•
1 x 8 pin 12V power connectors
•
(Hi-Density Power Connector)
1 x Front panel audio connector
•
2 x USB 2.0 headers (support 4 USB 2.0 ports)
•
1 x Vertical Type A USB 2.0
•
1 x USB 3.0 header (supports 2 USB 3.0 ports)
•
1 x Power Switch with LED
•
1 x Reset Switch with LED
•
1 x Clear CMOS Button
•
1 x Post Status Checker (PSC)
•
1 x Slow Mode Switch
•
1 x LN2 Mode Switch
•
1 x BIOS Selection Switch
•
BIOS
Feature
2 x 64Mb AMI UEFI Legal BIOS with Multilingual GUI sup-
•
port (1 x Main BIOS and 1 x Backup BIOS)
Supports Secure Backup UEFI Technology
•
ACPI 1.1 Compliance Wake Up Events
•
SMBIOS 2.3.1 Support
•
CPU, DRAM, PCH 1.05V, PCH 1.5V Voltage Multi-adjust-
Please realize that the re is a certain risk involved with overclocking, including adjusting
the setting in the BIOS, applying Untied Overclocking Technology, or using third-party
overclocking tools. O verclocking may aect your system’s stability, or even cause damage to
the components and devices of your system. It should be done at your ow n risk and expense.
We are not responsible for possible damage caused by overclocking.
•
FCC, CE, WHQL
•
ErP/EuP Ready (ErP/EuP ready power supply is required)
•
Due to limitation , the actual memory size may be less than 4GB for the re servation for system usage under Windows® 32-bit operating systems. Windows® 64-bit operating systems
do not have such limitations. You can use ASRock XFast RAM to utilize the memory that
Windows® cannot use.
English
1011
Page 13
Z87M OC Formula
1.3 Unique Features
ASRock Formula Drive
Formula Drive is ASRock’s multi purpose soware suite with a new interface, more
new features and improved utilities, including XFast RAM, Dehumidier, Good
Night LED, FAN-Tastic Tuning, OC Tweaker and a whole lot more.
ASRock Instant Flash
ASRock Instant Flash is a BIOS ash utility embedded in Flash ROM. is convenient BIOS update tool allows you to update the system BIOS in a few clicks without
preparing an additional oppy diskette or other complicated ash utility. Just save
the new BIOS le to your USB storage and launch this tool by pressing <F6> or
<F2> during POST to enter the BIOS setup menu to access ASRock Instant Flash.
Please be noted that the USB ash drive or hard drive must use FAT32/16/12 le
system.
ASRock APP Charger
Simply by installing the ASRock APP Charger makes your iPhone/iPad/iPod Touch
charge up to 40% faster than before on your computer. ASRock APP Charger allows
you to quickly charge many Apple devices simultaneously and even supports
continuous charging when your PC enters into Standby mode (S1), Suspend to RAM
(S3), hibernation mode (S4) or power o (S5).
ASRock XFast USB
ASRock XFast USB can boost the performance of your USB storage devices. e
performance may depend on the properties of the device.
ASRock XFast LAN
ASRock XFast LAN provides faster internet access, which includes the benets
listed below. LAN Application Prioritization: You can congure your application’s
priority ideally and add new programs to the list. Lower Latency in Game: Aer
setting online game’s priority higher, it can lower the latency in games. Trac
Shaping: You can watch Youtube HD videos and download simultaneously. RealTime Analysis of Your Data: With the status window, you can easily recognize
which data streams you are currently transferring.
English
Page 14
ASRock XFast RAM
ASRock XFast RAM is included in Formula Drive. It fully utilizes the memory
space that cannot be used under Windows® 32-bit operating systems. ASRock
XFast RAM shortens the loading time of previously visited websites, making web
surng faster than ever. And it also boosts the speed of Adobe Photoshop 5 times
faster. Another advantage of ASRock XFast RAM is that it reduces the frequency of
accessing your SSDs or HDDs in order to extend their lifespan.
ASRock Crashless BIOS
ASRock Crashless BIOS allows users to update their BIOS without fear of failing. If
power loss occurs during the BIOS updating process, ASRock Crashless BIOS will
automatically nish the BIOS update procedure aer regaining power. Please note
that BIOS les need to be placed in the root directory of your USB disk. Only USB 2.0
ports support this feature.
ASRock OMG (Online Management Guard)
Administrators are able to establish an internet curfew or restrict internet access
at specied times via OMG. You may schedule the starting and ending hours of
internet access granted to other users. In order to prevent users from bypassing
OMG, guest accounts without permission to modify the system time are required.
ASRock Internet Flash
ASRock Internet Flash downloads and updates the latest UEFI rmware version
from our servers for you without entering Windows® OS. Please setup network
conguration before using Internet Flash.
ASRock UEFI System Browser
ASRock System Browser shows the overview of your current PC and the devices
connected.
ASRock Dehumidier Function
Users may prevent motherboard damages due to dampness by enabling
“Dehumidier Function”. When enabling Dehumidier Function, the computer
will power on automatically to dehumidify the system aer entering S4/S5 state.
ASRock Easy RAID Installer
English
ASRock Easy RAID Installer can help you to copy the RAID driver from the
support CD to your USB storage device. Aer copying the RAID driver to your
USB storage device, please change “SATA Mode” to “RAID”, then you can start
installing the OS in RAID mode.
1213
Page 15
Z87M OC Formula
ASRock Easy Driver Installer
For users that don’t have an optical disk drive to install the drivers from our support
CD, Easy Driver Installer is a handy tool in the UEFI that installs the LAN driver
to your system via an USB storage device, then downloads and installs the other
required drivers automatically.
ASRock Interactive UEFI
ASRock Interactive UEFI is a blend of system conguration tools, cool sound eects
and stunning visuals. e unprecedented UEFI provides a more attractive interface
and more amusment.
ASRock Fast Boot
With ASRock’s exclusive Fast Boot technology, it takes less than 1.5 seconds to
logon to Windows 8 from a cold boot. No more waiting! e speedy boot will
completely change your user experience and behavior.
ASRock Restart to UEFI
Windows® 8 brings the ultimate boot up experience. e lightning boot up speed
makes it hard to access the UEFI setup. ASRock Restart to UEFI allows users to
enter the UEFI automatically when turning on the PC. By enabling this function,
the PC will enter the UEFI directly aer you restart.
NickShih’s OC Prole
Have you ever wondered how the global OC champion overclocks his
motherboards? Now you’ve got a chance to learn a few tricks from the champion
with NickShih’s OC Prole. It doesn’t matter whether you’re using a K-Series or
No-K Series CPU, NickShih’s OC Prole will automatically detect your CPU and
oer you dierent levels of overclocking. Have a taste of Nick’s secret recipe for
overclocking this motherboard instantly.
Fine-Tuning V-Controller
Fine-Tuning V-Controller is a new collection of voltage ne tuning options in
ASRock UEFI Setup Utility. It provides more than enough voltage conguration
options for overclockers who wish to pursuit extremes.
Timing Congurator
Timing Congurator is a fast and easy tool that provides users with an abundant
collection of subtle DRAM settings for professional tweaking. You won’t even
have to waste time on entering into the UEFI or restarting the system, Timing
Congurator is an independent application that runs under Windows® OS and your
changes will take eect immediately.
English
Page 16
ASRock Good Night LED
ASRock Good Night LED technology oers you a better sleeping environment by
extinguishing the unessential LEDs. By enabling Good Night LED in the BIOS, the
Power/HDD LEDs will be switched o when the system is powered on. Good night
LED will automatically switch o the Power and Keyboard LEDs when the system
enters into Standby/Hibernation mode as well.
ASRock USB Key
In a world where time is money, why waste precious time everyday typing
usernames to log in to Windows? Why should we even bother memorizing those
foot long passwords? Just plug in the USB Key and let your computer log in to
windows automatically!
ASRock Home Cloud
is motherboard supports remote wake with the onboard Intel LAN, so you can connect
with your PC from anywhere in the world. You will be able to power your PC on or turn it
o, monitor and take control of it remotely with another smartphone, tablet or computer.
ASRock FAN-Tastic Tuning
ASRock FAN-Tastic Tuning is included in Formula Drive. Congure up to ve different fan speeds using the graph. e fans will automatically shi to the next speed
level when the assigned temperature is met.
ASRock Distortion-Free Slot
ASRock's new pin design for the memory slots may appear to be the same as former
designs, but actually eectively reduces distortion and promotes performance,
because we strive for perfection even in the most trivial details.
English
1415
Page 17
Z87M OC Formula
Chapter 2 Installation
is is an Micro ATX form factor motherboard. Before you install the motherboard,
study the conguration of your chassis to ensure that the motherboard ts into it.
Pre-installation Precautions
Take note of the following precautions before you install motherboard components
or change any motherboard settings.
Make sure to unplug the power cord before installing or removing the motherboard.
•
Failure to do so may cause physical injuries to you and damages to motherboard
components.
In order to avoid damage from static electricity to the motherboard’s components,
•
NEVER place your motherboard directly on a carpet. Also remember to use a grounded
wrist strap or touch a safety grounded object before you handle the components.
Hold components by the edges and do not touch the ICs.
•
Whenever you uninstall any components, place them on a grounded anti-static pad or
•
in the bag that comes with the components.
When placing screws to secure the motherboard to the chassis, please do not over-
•
tighten the screws! Doing so may damage the motherboard.
English
Page 18
2.1 Installing the CPU
1. Before you insert the 1150-Pin CPU into the socket, please check if the P nP cap is on the
socket, if the CPU surface is unclean, or if there are any bent pins in the sock et. Do not
force to in sert the CPU into the socket if above situation is found . Otherwise, the CPU
will be seriously damaged.
2. Unplug all power cables before in stalling the CPU.
1
A
B
2
English
1617
Page 19
Z87M OC Formula
3
5
4
English
Page 20
Please save and replace the cover if the processor i s removed. e cover must be placed if
you wish to return the motherboard for aer service.
English
1819
Page 21
2.2 Installing the CPU Fan and Heatsink
12
Z87M OC Formula
FAN
CPU_
English
Page 22
2.3 Installing Memory Modules (DIMM)
is motherboard provides four 240-pin DDR3 (Double Data Rate 3) DIMM slots,
and supports Dual Channel Memory Technology.
1. For dual channel conguration , you always need to in stall identical (the same brand,
speed , size and chip-type) DDR3 DIMM pairs.
2. It is unable to activate Dual Channel Memor y Technolog y with only one or three memory
module installed.
3. It is not allowed to install a DDR or DDR2 memory module into a DDR3 slot; other wise,
this motherboard and DIMM may be damaged.
e DIMM only ts in one correct orientation. It will cause permanent damage to the
motherboard and the DIMM if you force the DIMM into the slot at incorrect orientation.
English
2021
Page 23
Z87M OC Formula
1
2
3
English
Page 24
2.4 Expansion Slots (PCI and PCI Express Slots)
ere are 4 PCI Express slots, 1 mini-PCI Express slot, and 1 mSATA/mini-PCI
Express slot on this motherboard.
Before installing an ex pansion card, please make sure that the power supply is switched o
or the power cord is unplugged. Please re ad the documentation of the expansion card and
make necessary hardware settings for the card before you start the installation.
PCIe slots:
PCIE1 (PCIe 3.0 x16 slot) is used for PCI Express x16 lane width graphics cards.
PCIE2 (PCIe 2.0 x1 slot) is used for PCI Express x1 lane width cards.
PCIE3 (PCIe 3.0 x16 slot) is used for PCI Express x8 lane width graphics cards.
PCIE4 (PCIe 3.0 x16 slot) is used for PCI Express x4 lane width graphics cards.
MINI_PCIE1 (mini-PCIe slot) is used for WiFi module.
MINI_PCIE2 (mSATA/mini-PCIe slot) is used for mSATA or mini-PCIe module.
*** e mSATA/mini-PCIe slot is shared w ith SATA3_4 connector.
PCIe Slot Congurations
PCIE1PCIE3
Single Graphics Cardx16x8
Two Graphics Cards in
CrossFireXTM or SLITM Mode
For a better thermal environment, please connect a chassis fan to the motherboard’s chassis
fan connector (CHA_FAN1 or CH A_FAN2) when using multiple graphics card s.
N/Ax8
English
2223
Page 25
2.5 Jumpers Setup
e illustration shows how jumpers are setup. When the jumper cap is placed on
the pins, the jumper is “Short”. If no jumper cap is placed on the pins, the jumper
is “Open”. e illustration shows a 3-pin jumper whose pin1 and pin2 are “Short”
when a jumper cap is placed on these 2 pins.
Clear CMOS Jumper
(CLRCMO S1)
(see p.1, No. 22)
CLRCMOS1 allows you to clear the data in CMOS. To clear and reset the system
parameters to default setup, please turn o the computer and unplug the power
cord from the power supply. Aer waiting for 15 seconds, use a jumper cap to
short pin2 and pin3 on CLRCMOS1 for 5 seconds. However, please do not clear
the CMOS right aer you update the BIOS. If you need to clear the CMOS when
you just nish updating the BIOS, you must boot up the system rst, and then shut
it down before you do the clear-CMOS action. Please be noted that the password,
date, time, and user default prole will be cleared only if the CMOS battery is
removed.
Clear CMOSDefault
Z87M OC Formula
e Clear CMOS Button has the same function as the Clear CMOS jumper.
English
Page 26
2.6 Onboard Headers and Connectors
1
Onboard headers and connectors are NOT jumpers. Do NOT place jumper caps over these
heade rs and connectors. Placing jumper caps over the headers and connectors will cause
permanent damage to the motherboard.
System Panel Header
(9-pi n PANEL1)
(see p.1, No. 17)
PWRBTN (Power Switch):
Connec t to the power switch on the chassi s front panel. You may congure the way to tur n
o your system using the power switch.
RESET (Reset Switch):
Connec t to the reset switch on the chassi s front panel. Press the reset sw itch to restart the
computer if the computer f reezes and fails to per form a normal restar t.
PLED (Syste m Power LED):
Connec t to the power status indicator on the chassis front panel. e LED i s on when the
system is operating. e LED keeps blinking when the system is in S1/S3 sleep state. e
LED is o when the system is in S4 slee p state or powered o (S5).
HDLED (Ha rd Drive Activity LED):
Connec t to the hard drive activity LED on the chassis front panel. e LED is on when the
hard drive is reading or wr iting data.
e front panel design may dier by chassis. A front panel module mainly consists of powe r
switch, reset switch , power LED, hard dr ive activity LED, speaker and etc. When connecting your chassi s front panel module to thi s header, make sure the wire a ssignments and the
pin assignments are matched correctly.
PLED+
PLED-
HDLED-
HDLED+
PWRBTN#
GND
RESET#
GND
GND
Connect the power
switch, reset switch and
system status indicator on
the chassis to this header
according to the pin
assignments below. Note
the positive and negative
pins before connecting
the cables.
English
2425
Page 27
Z87M OC Formula
1
PLED+
PLED+
PLED-
DUMMY
GND
GND
P+
P-
USB_PWR
P+
P-
USB_PWR
1
1
Power LED Header
(3-pin PLED1)
(see p.12, No. 16)
Serial ATA3 Connectors
(SATA3_0_1:
see p.1, No. 12)
(SATA1_2_3:
see p.1, No. 13)
(SATA3_4_5:
see p.1, No. 14)
USB 2.0 Headers
(9-pin USB2_3)
(see p.1, No. 23)
(9-pin USB4_5)
(see p.1, No. 24)
SATA3_0_1SATA3_4_5SATA3_2_3
Please connect the chassis
power LED to this header
to
indicate the system’s
power status.
ese six SATA3
connectors support SATA
data cables for internal
storage devices with up to
6.0 Gb/s data transfer rate.
Besides two USB 2.0 ports
on the I/O panel, there
are two headers and one
port on this motherboard.
Each USB 2.0 header can
support two ports.
(USB6)
(see p.1, No. 9)
USB 3.0 Headers
(19-pin USB3_6_7)
(see p.1, No. 10)
Vbus
IntA_PA_SSRX-
IntA_PA_SSRX+
GND
IntA_PA_SSTX-
IntA_PA_SSTX+
GND
IntA_PA_D-
IntA_PA_D+
VbusVbus
IntA_PB_SSRX-
IntA_PB_SSRX+
GND
IntA_PB_SSTX-
IntA_PB_SSTX+
GND
IntA_PB_D-
IntA_PB_D+
Dummy
Besides six USB 3.0 ports
on the I/O panel, there
are one header on this
motherboard. Each USB
3.0 header can support
two ports.
English
Page 28
Front Panel Audio Header
J_SENSE
OUT2_L
1
MIC_RET
PRESENCE#
GND
OUT2_R
MIC2_R
MIC2_L
OUT_RET
1
SPEAKER
GND
OL
(9-pin HD_ AUDIO1)
(see p.1, No. 29)
1. High Denition Audio supports Jack Sensing, but the panel wire on the chassis must support HDA to function correctly. Please follow the instructions in our manual and chassis
manual to install your system.
2. If you use an AC’97 audio panel , please install it to the front panel audio header by the
steps below:
A. Connect Mic_IN (MIC) to MIC2_ L.
B. Conne ct Audio_R (RIN) to OUT2_R and Audio_ L (LIN) to OUT2_ L.
C. Connect Ground (GND) to Ground (GND).
D. MIC_ RET and OUT_RET are for the HD audio panel only. You don’t need to connect
them for the AC’97 audio panel .
E. To activate the front mic, go to the “FrontMic” Tab in the Realtek Control panel and
adjust “Recording Volume”.
is header is for
connecting audio devices
to the front audio panel.
Chassis Speaker Header
(4-pin SPEAKER1)
(see p.1, No. 15)
Chassis and Power Fan
Connectors
(4-pin CHA_FAN1)
(see p.1, No. 27)
DUMMY
+5V
+12V
CHA_FAN_SPEED
FAN_SPEED_CONTR
DUMMY
Please connect the chassis
speaker to this header.
Please connect fan cables
to the fan connectors and
match the black wire to
the ground pin.
(3-pi n CHA_FAN2)
(see p.1, No. 26)
(3-pi n CHA_FAN3)
English
(see p.1, No. 11)
(3-pin PW R_ FA N1)
(see p.1, No. 30)
2627
Page 29
Z87M OC Formula
CPU_FAN_SPEED
N_SPEED
FA
4
8 5
1
RRI#1
DUMMY
1
CPU Fan Connectors
(4-pin CPU_FAN1)
(see p.1, No. 3)
(3-pin CPU_FAN2)
(see p.1, No. 2)
ATX Power Connector
(24-pin ATXPWR1)
(see p.1, No. 8)
ATX 12V Power
Connector
(8-pin ATX12V1)
(see p.1, No. 1)
4 3 2 1
+12V
N_SPEED_CONTROL
CPU_FA
GND
+12V
12
1
is motherboard provides a 4-Pin CPU fan
GN D
(Quiet Fan) connector.
If you plan to connect a
3-Pin CPU fan, please
connect it to Pin 1-3.
24
is motherboard provides a 24-pin ATX power
connector. To use a 20-pin
ATX power supply, please
plug it along Pin 1 and Pin
13
13.
is motherboard provides an 8-pin ATX 12V
1
power connector. To use a
4-pin ATX power supply,
please plug it along Pin 1
and Pin 5.
Infrared Module Header
(5-pin IR 1)
(see p.1, No. 28)
Serial Port Header
(9-pin COM1)
(see p.1, No. 25)
IRTX
IRRX
RRXD1
DDTR#1
TTXD1
DDCD#1
+5VSB
GND
DDSR#1
CCTS#1
RRTS#1
GND
is header supports an optional
wireless transmitting and
receiving infrared module.
is COM1 header
supports a serial port
module.
English
Page 30
2.7 Smart Switches
AB
e motherboard has three smart switches: Power Switch, Reset Switch and Clear
CMOS Button, allowing users to quickly turn on/o the system, reset the system or
clear the CMOS values.
Power Switch
(PWRBTN)
(see p.1, No. 18)
Reset Switch
(RSTBTN)
(see p.1, No. 19)
Clear CMOS Button
(CLRCBTN)
(see p.1, No. 20)
is function i s workable only when you power o your computer and unplug the powe r
supp ly.
Slow Mode Switch
(SLOWMODE1)
(see p.1 No. 6)
BIOS Selection
Switch
(BIOS_SEL1)
(see p.1 No. 21)
Power
Reset
OFF
ON
Power Switch allows users
to quickly turn on/o the
system.
Reset Switch allows
users to quickly reset the
system.
Clear CMOS Button
allows users to quickly
clear the CMOS values.
If Slow Mode is on, the
processor runs at lowest
frequency.
BIOS Selection Switch
allows the system to boot
from either BIOS A or
BIOS B.
English
is motherboard h as two BIOS chips, a p rimary BIOS (BIOS_A) and a backup BIOS (BIOS_
B), which enhances the safety and stability of your system. Normally, the system will work
on the primary BIOS. However, if the primary BIOS is corrupted or damaged, ju st ip the
BIOS Selection Sw itch to “B”, then the backup BIOS will take over on the next system boot.
Aer that, use “Secure Backup U EFI” in the UEFI Setup Utility to duplicate a working copy
of the BIOS les to the primary BIOS to ensure normal system operation. For safety issues,
users are not able to update the backup BIOS manu ally. Users may refer to the BIOS LEDs
(BIOS_ A_LED or BIOS_B_ LED) to identify which BIOS i s currently activated .
2829
Page 31
LN2 Mode Switch
(LN2MODE1)
(see p.1, No. 7)
OFF
ON
Z87M OC Formula
e LN2 mode aids in
eliminating the cold-boot bug
issues in processors during
extreme overclocking with
Liquid Nitrogen.
English
Page 32
1 Einleitung
Vielen Dank, dass Sie sich für das Z87M OC Formula von ASRock entschieden
haben – ein zuverlässiges Motherboard, das konsequent unter der strengen
Qualitätskontrolle von ASRock hergestellt wurde. Es liefert ausgezeichnete Leistung
mit robustem Design, das ASRocks Streben nach Qualität und Beständigkeit erfüllt.
Da die technischen Daten des Motherboards sowie die BIOS-Soware aktualisiert werden
können, kann der Inhalt dieser Dokumentation ohne Ankündigung geändert werden. Falls
diese Dokumentation irgendwelchen Änderungen unterliegt, wird die aktualisierte Version
ohne weitere Hinweise auf der ASRock-Webseite zur Verfügung gestellt. Sollten Sie technische
Hilfe in Bezug auf dieses Motherboard benötigen, erhalten Sie auf unserer Webseite spezischen
Informationen über das von Ihnen verwendete Modell. Auch nden Sie eine aktuelle Liste
unterstützter VGA-Karten und Prozessoren auf der ASRock-Webseite: ASRock-Website
http://www.asrock.com.
• 2 x PCI-Express 3.0-x16-Steckplätze (PCIE1/PCIE3:einzeln bei
x16 (PCIE1); doppelt bei x8 (PCIE1) / x8 (PCIE3))
• 1 x PCI-Express 2.0-x4-Steckplatz
• 1 x PCI-Express 2.0-x1-Steckplatz
• 1 x Mini-PCI-Express-Steckplatz (halbe Größe)
• 1 x mSATA/Mini-PCI-Express-Steckplatz
* mSATA/Mini-PCI-Express-Steckplatz mit SATA3_4-Port
geteilt
• Unterstützt AMD Quad CrossFireXTM und CrossFireXTM
• Unterstützt NVIDIA® Quad SLITM und SLI
• Integrierte Intel® HD Graphics-Visualisierung und VGA-
Ausgänge können nur mit Prozessoren unterstützt werden, die
GPU-integriert sind.
• Unterstützt integrierte Intel® HD Graphics-Visualisierung:
Intel® Quick Sync Video mit AVC, MVC (S3D) und MPEG-2
Full HW Encode1, Intel® InTruTM 3D, Intel® Clear Video HD
Technology, Intel® InsiderTM, Intel® HD Graphics 4400/4600
• Pixel Shader 5.0, DirectX 11.1
• Max. geteilter Speicher: 1792 MB
• VGA-Zweifachausgang:unterstützt HDMI- und DisplayPort-
Ports durch unabhängige Monitor-Controller
• Unterstützt HDMI-Technologie mit maximaler Auösung von
4K x 2K (4096 x 2304) bei 24 Hz
• Unterstützt DisplayPort mit maximaler Auösung von 4K x 2K
(4096 x 2304) bei 24 Hz
• Unterstützt Auto-Lippensynchronizität, hohe Farbtiefe (12
bpc), xvYCC und HBR (Audio mit hoher Bitrate) mit HDMI
(konformer HDMI-Monitor erforderlich)
• Unterstützt HDCP-Funktion bei HDMI- und DisplayPortPorts
• Unterstützt Blu-ray- (BD) Wiedergabe (Full HD/1080p) bei
HDMI- und DisplayPort-Ports
TM
Page 35
Z87M OC Formula
Audio
LAN
Rückblende,
E/A
• 7.1-Kanal-HD-Audio mit Inhaltsschutz (Realtek ALC1150Audiocodec)
• Erstklassige Blu-ray-Audiounterstützung
• Unterstützt Purity Sound™
- 115-dB-SRV-DAC mit Dierentialverstärker
- TI® NE5532 erstklassiger Headset-Verstärker (unterstützt
Headsets mit bis zu 600 Ohm)
- Direct Drive Technology
- Abdeckung mit EMV-Abschirmung
- PCB-isolierte Abschirmung
• Unterstützt DTS Connect
• Gigabit LAN 10/100/1000 Mb/s
• Giga PHY Intel® I217V
• Unterstützt Intel® Remote Wake Technology
• Unterstützt Wake-On-LAN
• Unterstützt energieezientes Ethernet 802.3az
• Unterstützt PXE
• 1 x PS/2-Maus-/Tastaturanschluss
• 1 x HDMI-Ausgang
• 1 x HDMI-Eingang
• 1 x DisplayPort
• 1 x Optischer SPDIF-Ausgang
• 1 x eSATA-Anschluss
• 2 x USB 2.0-Ports
• 4 x USB 3.0-Ports (Intel® Z87) (ASMedia-Hub)
• 2 x USB 3.0-Ports (Intel® Z87)
• 1 x RJ-45-LAN-Port mit LED (Aktivität/Verbindung-LED und
* Detaillierte Produktinformationen nden Sie auf unserer Webseite: http://www.asrock.com
Bitte beachten Sie, dass mit einer Übertaktung, zu der die Anpassung von BIOSEinstellungen, die Anwendung der Untied Overclocking Technology oder die Nutzung von
Übertaktungswerkzeugen von Drittanbietern zählen, bestimmte Risiken verbunden sind. Eine
Übertaktung kann sich auf die Stabilität Ihres Systems auswirken und sogar Komponenten und
Geräte Ihres Systems beschädigen. Sie sollte auf eigene Gefahr und eigene Kosten durchgeführt
werden. Wir übernehmen keine Verantwortung für mögliche Schäden, die durch eine
Übertaktung verursacht wurden.
Aufgrund von Beschränkungen kann die Größe des tatsächlich für die Systemnutzung
reservierten Speichers unter Windows®-Betriebssystemen mit 32 Bit weniger als 4 GB betragen.
Windows®-Betriebssysteme mit 64 Bit haben keine derartigen Beschränkungen. Mit ASRock
XFast RAM können Sie den Speicher einsetzen, den Windows® nicht nutzen kann.
Deutsch
35
Page 38
1.3 Jumpereinstellung
Die Abbildung zeigt, wie die Jumper eingestellt werden. Wenn die Jumper-Kappe auf
den Kontakten angebracht ist, ist der Jumper „kurzgeschlossen“. Wenn keine JumperKappe auf den Kontakten angebracht ist, ist der Jumper „oen“. Die Abbildung zeigt
einen 3-poligen Jumper, dessen Kontakt 1 und Kontakt 2 „kurzgeschlossen“ sind,
wenn eine Jumper-Kappe auf diesen 2 Kontakten angebracht ist.
CMOS-löschen-Jumper
(CLRCMOS1)
(siehe S. 1, Nr. 22)
CLRCMOS1 ermöglicht Ihnen die Löschung der Daten im CMOS. Zum Löschen
und Rücksetzen der Systemparameter auf die Standardeinrichtung schalten Sie
den Computer bitte ab und ziehen das Netzkabel aus der Steckdose. Warten Sie 15
Sekunde, schließen Sie dann Kontakt 2 und Kontakt 3 an CLRCMOS1 5 Sekunden
lang mit einer Jumper-Kappe kurz. Löschen Sie den CMOS jedoch nicht direkt nach
der BIOS-Aktualisierung. Falls Sie den CMOS direkt nach Abschluss der BIOSAktualisierung löschen müssen, starten Sie das System zunächst; fahren Sie es dann
vor der CMOS-Löschung herunter. Bitte beachten Sie, dass Kennwort, Datum, Zeit
und Benutzerstandardprol nur gelöscht werden, wenn die CMOS-Batterie entfernt
wird.
CMOS löschenStandard
Deutsch
36
Die CMOS-löschen-Taste hat dieselbe Funktion wie der CMOS-löschen-Jumper.
Page 39
1.4 Integrierte Stiftleisten und Anschlüsse
Integrierte Stileisten und Anschlüsse sind KEINE Jumper. Bringen Sie KEINE Jumper-Kappen
an diesen Stileisten und Anschlüssen an. Durch Anbringen von Jumper-Kappen an diesen
Stileisten und Anschlüssen können Sie das Motherboard dauerha beschädigen.
Z87M OC Formula
Systemblende-Stileiste
(9-polig, PANEL1)
(siehe S. 1, Nr. 17)
PWRBTN (Ein-/Austaste):
Mit der Ein-/Austaste an der Frontblende des Gehäuses verbinden. Sie können die Abschaltung
Ihres Systems über die Ein-/Austaste kongurieren.
RESET (Reset-Taste):
Mit der Reset-Taste an der Frontblende des Gehäuses verbinden. Starten Sie den Computer
über die Reset-Taste neu, wenn er abstürzt oder sich nicht normal neu starten lässt.
PLED (Systembetriebs-LED):
Mit der Betriebsstatusanzeige an der Frontblende des Gehäuses verbinden. Die LED leuchtet,
wenn das System läu. Die LED blinkt, wenn sich das System im S1/S3-Ruhezustand bendet.
Die LED ist aus, wenn sich das System im S4-Ruhezustand bendet oder ausgeschaltet ist (S5).
HDLED (Festplattenaktivitäts-LED):
Mit der Festplattenaktivitäts-LED an der Frontblende des Gehäuses verbinden. Die LED
leuchtet, wenn die Festplatte Daten liest oder schreibt.
Das Design der Frontblende kann je nach Gehäuse variieren. Ein Frontblendenmodul
besteht hauptsächlich aus Ein-/Austaste, Reset-Taste, Betrieb-LED, Festplattenaktivität-LED,
Lautsprecher etc. Stellen Sie beim Anschließen Ihres Frontblendenmoduls an diese Stileiste
sicher, dass Kabel- und Pinbelegung richtig abgestimmt sind.
1
PLED+
PLED-
HDLED-
HDLED+
PWRBTN#
GND
RESET#
GND
GND
Verbinden Sie
Netzschalter, Reset-Taste
und Systemstatusanzeige
am Gehäuse entsprechend
der nachstehenden
Pinbelegung mit dieser
Stileiste. Beachten Sie vor
Anschließen der Kabel die
positiven und negativen
Kontakte.
37
Deutsch
Page 40
Betrieb-LED-Stileiste
1
PLED+
PLED+
PLED-
DUMMY
GND
GND
P+
P-
USB_PWR
P+
P-
USB_PWR
1
1
(3-polig, PLED1)
(siehe S. 12, Nr. 16)
Bitte verbinden Sie
die Betrieb-LED des
Gehäuses zur
Anzeige des
Systembetriebsstatus mit
dieser Stileiste.
Deutsch
Serial-ATA-III-Anschlüsse
(SATA3_0_1:
siehe S. 1, Nr. 12)
(SATA1_2_3:
siehe S. 1, Nr. 13)
(SATA3_4_5:
siehe S. 1, Nr. 14)
USB 2.0-Stileisten
(9-polig, USB2_3)
(siehe S. 1, Nr. 23)
(9-polig, USB4_5)
(siehe S. 1, Nr. 24)
(USB6)
(siehe S. 1, Nr. 9)
USB 3.0-Stileisten
(19-polig, USB3_6_7)
(siehe S. 11, Nr. 10)
SATA3_0_1SATA3_4_5SATA3_2_3
Vbus
IntA_PA_SSRX-
IntA_PA_SSRX+
IntA_PA_SSTX-
IntA_PA_SSTX+
IntA_PA_D-
IntA_PA_D+
Diese sechs SATA-IIIAnschlüsse unterstützen
SATA-Datenkabel für
interne Speichergeräte mit
einer Datenübertragungsge
schwindigkeit bis 6,0 Gb/s.
Neben zwei USB 2.0-Ports
an der E/A-Blende
benden sich zwei
Stileisten und ein Port an
diesem Motherboard. Jede
USB 2.0-Stileiste kann
zwei Ports unterstützen.
VbusVbus
IntA_PB_SSRX-
IntA_PB_SSRX+
GND
IntA_PB_SSTX-
GND
IntA_PB_SSTX+
GND
IntA_PB_D-
GND
IntA_PB_D+
Dummy
Neben sechs USB 3.0-Ports
an der E/A-Blende bendet
sich eine Stileiste an
diesem Motherboard. Jede
USB 3.0-Stileiste kann
zwei Ports unterstützen.
38
Page 41
Z87M OC Formula
J_SENSE
OUT2_L
1
MIC_RET
PRESENCE#
GND
OUT2_R
MIC2_R
MIC2_L
OUT_RET
1
DUMMY
SPEAKER
GND
OL
Audiostileiste
(Frontblende)
(9-polig, HD_AUDIO1)
(siehe S. 1, Nr. 29)
1. High Denition Audio unterstützt Anschlusserkennung, der Draht am Gehäuse muss dazu
jedoch HDA unterstützt. Bitte befolgen Sie zum Installieren Ihres Systems die Anweisungen
in unserer Anleitung und der Anleitung zum Gehäuse.
2. Bei Nutzung eines AC’97-Audiopanels dieses bitte anhand folgender Schritte an der
Audiostileiste der Frontblende installieren:
A. Mic_IN (Mikrofon) mit MIC2_L verbinden.
B. Audio_R (RIN) mit OUT2_R und Audio_L (LIN) mit OUT2_L verbinden.
C. Erde (GND) mit Erde (GND) verbinden.
D. MIC_RET und OUT_RET sind nur für das HD-Audiopanel vorgesehen. Sie müssen sie
nicht für das AC’97-Audiopanel verbinden.
E. Rufen Sie zum Aktivieren des vorderen Mikrofons das „FrontMic (Vorderes
Mikrofon)“-Register in der Realtek-Systemsteuerung auf und passen „Recording Volume
(Aufnahmelautstärke)“ an.
Gehäuselautsprecherstileiste
+5V
(4-polig, SPEAKER1)
DUMMY
Diese Stileiste dient
dem Anschließen von
Audiogeräten an der
Frontblende.
Bitte verbinden Sie den
Gehäuselautsprecher mit
dieser Stileiste.
(siehe S. 1, Nr. 15)
Gehäuse- und
Netzteillüeranschlüsse
(4-polig, CHA_FAN1)
(siehe S. 1, Nr. 27)
(3-polig, CHA_FAN2)
(siehe S. 1, Nr. 26)
(3-polig, CHA_FAN3)
(siehe S. 1, Nr. 11)
(3-polig, PWR_FAN1)
(siehe S. 1, Nr. 30)
+12V
CHA_FAN_SPEED
FAN_SPEED_CONTR
Bitte verbinden Sie die
Lüerkabel mit den
Lüeranschlüssen; der
schwarze Draht gehört
zum Erdungskontakt.
Deutsch
39
Page 42
CPU-Lüeranschlüsse
CPU_FAN_SPEED
N_SPEED
FA
4 1
8 5
RRI#1
1
(4-polig, CPU_FAN1)
(siehe S. 1, Nr. 3)
(3-polig, CPU_FAN2)
(siehe S. 1, Nr. 2)
4 3 2 1
+12V
N_SPEED_CONTROL
CPU_FA
GND
+12V
GN D
Dieses Motherboard bietet
einen 4-poligen CPULüeranschluss (lautloser
Lüer). Falls Sie einen
3-poligen CPU-Lüer
anschließen möchten,
verbinden Sie ihn bitte mit
Kontakt 1 bis 3.
Deutsch
ATX-Netzanschluss
(24-polig, ATXPWR1)
(siehe S. 1, Nr. 8)
ATX-12-V-Netzanschluss
(8-polig, ATX12V1)
(siehe S. 1, Nr. 1)
Infrarotmodul-Stileiste
(5-polig, IR1)
(siehe S. 1, Nr. 28)
Serieller-Port-Stileiste
(9-polig, COM1)
(siehe S. 1, Nr. 25)
1
IRTX
IRRX
RRXD1
DDTR#1
TTXD1
DDCD#1
+5VSB
GND
DDSR#1
GND
DUMMY
CCTS#1
RRTS#1
Dieses Motherboard
bietet einen 24-poligen
ATX-Netzanschluss.
Bitte schließen Sie es zur
Nutzung eines 20-poligen
ATX-Netzteils entlang
Kontakt 1 und Kontakt 13
an.
Dieses Motherboard bietet
einen 8-poligen ATX-12V-Netzanschluss. Bitte
schließen Sie es zur Nutzung
eines 4-poligen ATXNetzteils entlang Kontakt 1
und Kontakt 5 an.
Diese Stileiste unterstützt
ein optionales kabelloses
Infrarotmodul zum Übertragen
und Empfangen.
Diese COM1-Stileiste
unterstützt ein Modul für
serielle Ports.
40
Page 43
Z87M OC Formula
AB
1.5 Intelligente Schalter
Das Motherboard hat drei intelligente Schalter: Ein-/Ausschalter, Reset-Schalter
und CMOS-löschen-Taste, wodurch Benutzer das System schnell ein-/abschalten,
zurücksetzen bzw. die CMOS-Werte löschen können.
Ein-/Ausschalter
(PWRBTN)
(siehe S. 1, Nr. 18)
Reset-Schalter
(RSTBTN)
(siehe S. 1, Nr. 19)
CMOS-löschen-Taste
(CLRCBTN)
(siehe S. 1, Nr. 20)
Diese Funktion ist nur verfügbar, wenn Sie Ihren Computer abschalten und die Stromversorgung unterbrechen.
Langsamer-ModusSchalter(SLOWMODE1)
(siehe S. 1, Nr. 6)
Power
Reset
OFF
ON
Mit dem Ein-/Ausschalter
kann der Benutzer das
System schnell ein-/
abschalten.
Der Reset-Taste
ermöglicht das schnelle
Rücksetzen des Systems.
Mit der CMOS-löschenTaste können Benutzer
die CMOS-Werte schnell
löschen.
Wenn der langsame
Modus eingeschaltet ist,
arbeitet der Prozessor bei
niedrigster Frequenz.
BIOSAuswahlschalter(BIOS_
SEL1)(siehe S. 1, Nr. 21)
Dieses Motherboard verfügt über zwei BIOS-Chips, ein primäres BIOS (BIOS_A) und ein
Ausfall-BIOS (BIOS_B), die Sicherheit und Stabilität Ihres Systems steigern. Normalerweise
läu das System über das primäre BIOS. Falls das primäre BIOS jedoch beschädigt ist oder
ausfällt, stellen Sie den BIOS-Auswahlschalter einfach auf „B“ um; dann übernimmt das
Ausfall-BIOS beim nächsten Systemstart. Duplizieren Sie dann mit „Secure Backup UEFI“
im UEFI-Einrichtungsprogramm zur Gewährleistung eines normalen Systembetriebs eine
Arbeitskopie der BIOS-Dateien am primären BIOS. Aus Sicherheitsgründen können Benutzer
das Ausfall-BIOS nicht manuell aktualisieren. Sie können das aktuell aktivierte BIOS anhand
der BIOS-LEDs (BIOS_A_LED oder BIOS_B_LED) bestimmen.
Der BIOSAuswahlschalter
ermöglicht dem System,
von BIOS A oder BIOS B
zu starten.
Deutsch
41
Page 44
LN2-Modusschalter
(LN2MODE1)
(siehe S. 1, Nr. 7)
OFF
ON
Der LN2-Modus hil bei
der Eliminierung von
Kaltstartfehlern in Prozessoren
bei extremer Übertaktung mit
üssigem Sticksto.
Deutsch
42
Page 45
Z87M OC Formula
1 Introduction
Nous vous remercions d’avoir acheté cette carte mère ASRock Z87M OC Formula, une
carte mère able fabriquée conformément au contrôle de qualité rigoureux et constant
appliqué par ASRock. Fidèle à son engagement de qualité et de durabilité, ASRock
vous garantit une carte mère de conception robuste aux performances élevées.
Les spécications de la carte mère et du logiciel BIOS pouvant être mises à jour, le contenu
de ce document est soumis à modication sans préavis. En cas de modications du présent
document, la version mise à jour sera disponible sur le site Internet ASRock sans notication
préalable. Si vous avez besoin d’une assistance technique pour votre carte mère, veuillez visiter
notre site Internet pour plus de détails sur le modèle que vous utilisez. La liste la plus récente
des cartes VGA et des processeurs pris en charge est également disponible sur le site Internet de
ASRock. Site Internet ASRock http://www.asrock.com.
1.1 Contenu de l’emballage
• Carte mère ASRock Z87M OC Formula (facteur de forme Micro ATX)
• Guide d’installation rapide ASRock Z87M OC Formula
• CD d’assistance ASRock Z87M OC Formula
• 4 x câbles de données Serial ATA (SATA) (Optionnel)
• Prend en charge Intel® Extreme Memory Prole (XMP)1.3/1.2
• Fente anti-distorsion
• 2 x fentes PCI Express 3.0 x 16 (PCIE1/PCIE3 : simple à x16
(PCIE1) ; double à x8 (PCIE1) / x8 (PCIE3))
• 1 x fente PCI Express 2.0 x4
• 1 x fente PCI Express 2.0 x1
• 1 x fente mini-PCI Express half
• 1 x fente mSATA/ mini-PCI Express
* fente mSATA/mini-PCI Express partagée avec le port
SATA3_4
• Prend en charge AMD Quad CrossFireXTM et CrossFireXTM
• Prend en charge NVIDIA® Quad SLITM et SLI
• La technologie Intel® HD Graphics Built-in Visuals et les sorties
VGA sont uniquement prises en charge par les processeurs
intégrant un contrôleur graphique.
• Prend en charge la technologie Intel® HD Graphics Built-in
Visuals : Intel® Quick Sync Video avec AVC, MVC (S3D) et
MPEG-2 Full HW Encode1, Intel® InTruTM 3D, technologie
Intel® Clear Video HD, Intel® InsiderTM, Intel® HD Graphics
4400/4600
• Pixel Shader 5.0, DirectX 11.1
• Mémoire partagée max. 1792Mo
• Double sortie VGA:prend en charge les ports HDMI et
DisplayPort via contrôleurs d’achage indépendants
• Prend en charge la technologie HDMI avec résolution
maximale de 4K × 2K (4096x2304) @ 24Hz
• Prend en charge la technologie DisplayPort avec résolution
maximale de 4K × 2K (4096x2304) @ 24Hz
• Prend en charge les technologies Auto Lip Sync, Deep Color
(12bpc), xvYCC et HBR (High Bit Rate Audio) avec HDMI (un
écran compatible HDMI est requis)
• Prend en charge la fonction HDCP via ports HDMI et
DisplayPort
• Prend en charge la lecture Blu-ray (BD) Full HD 1080p via
ports HDMI et DisplayPort
TM
Français
45
45
Page 48
Audio
• Audio 7.1 CH HD avec protection du contenu (codec audio
Realtek ALC1150)
• Compatible audio Blu-ray Premium
• Prend en charge Purity Sound™
- 115dB SNR DAC avec amplicateur diérentiel
- Amplicateur de casque
- TI® NE5532 Premium (prend en charge les casques jusqu’à
600 Ohms)
- Technologie Direct Drive
- Capot à blindage CEM
- Blindage isolant PCB
• Prend en charge DTS Connect
Français
Réseau
Connectique
du panneau
arrière
• Gigabit LAN 10/100/1000 Mb/s
• Giga PHY Intel® I217V
• Prend en charge la technologie Intel® Remote Wake
• Prend en charge la fonction Wake-On-LAN
• Prend en charge la fonction d’économie d’énergie Ethernet
802.3az
• Prend en charge PXE
• 1 x port souris/clavier PS/2
• 1 x port de sortie HDMI
• 1 x port d’entrée HDMI
• 1 x DisplayPort
• 1 x port sortie optique SPDIF
• 1 x connecteur eSATA
• 2 x ports USB 2.0
• 4 x ports USB 3.0 (Intel® Z87) (concentrateur ASMedia)
• 2 x ports USB 3.0 (Intel® Z87)
• 1 x port RJ-45 LAN avec LED (LED ACT/LIEN et LED
VITESSE)
• 1 x bouton Clear CMOS
• Connecteurs jack audio HD : Haut-parleur arrière / central /
basses / entrée ligne / haut-parleur avant / microphone
• 1 x connecteur eSATA, compatibles RAID (RAID 0, RAID 1,
RAID 5, RAID 10, technologies Intel Rapid Storage 12 et Intel
Smart Response), fonctions NCQ, AHCI et «Hot Plug»
* le connecteur eSATA est partagé avec le port SATA3_1)
• 1 x embase IR
• 1 x embase pour port COM
• 1 x embase LED d’alimentation
• 2 x connecteurs pour ventilateur de processeur (1 x 4 broches,
1 x 3 broches)
• 3 x connecteurs pour ventilateur de châssis (1 x 4 broches, 2 x 3
broches)
• 1 x connecteur pour ventilateur d’alimentation (3 broches)
• 1 x connecteur d’alimentation ATX 24 broches
• 1 x connecteur d’alimentation 12V 8 broches
(Connecteur d’alimentation haute densité)
• 1 x connecteur audio panneau frontal
• 2 x embases USB 2.0 (pour 4 ports USB 2.0)
• 1 x port USB 2.0 type A vertical
• 1 x embase USB 3.0 (pour 2 ports USB 3.0)
• 1 x bouton de mise en marche avec témoin LED
• 1 x bouton de réinitialisation avec témoin LED
• 1 x bouton Clear CMOS
• 1 x Post Status Checker (PSC)
• 1 x interrupteur mode lent
• 1 x interrupteur mode LN2
• 1 x bouton de sélection du BIOS
Caractéristiques du BIOS
• 2 x BIOS UEFI AMI 64Mo avec prise en charge interface
graphique multilingue (1 x BIOS principal et 1 x BIOS de
sauvegarde)
• Prend en charge la technologie de sauvegarde sécurisée UEFI
• Compatible ACPI 1.1 Wake Up Events
• Prend en charge SMBIOS 2.3.1
• Réglage de la tension CPU, DRAM, PCH 1,05V, PCH 1,5V
47
47
Français
Page 50
CD inclus
• Utilitaires, logiciel AntiVirus (version d’évaluation), version
d’essai CyberLink MediaEspresso 6.5, navigateur Google
Chrome et barre d’outils, Start8, MeshCentral, Splashtop
Streamer
Français
Surveillance
• Détection de la température du processeur/châssis
* Pour des informations détaillées de nos produits, veuillez visiter notre site: http://www.asrock.com
Il est important de signaler que l'overcloking présente certains risques, incluant des
modications du BIOS, l’application d’une technologie d’overclocking déliée et l'utilisation
d'outils d'overclocking développés par des tiers. La stabilité de votre système peut être aectée
par ces pratiques, voire provoquer des dommages aux composants et aux périphériques du
système. L’overclocking se fait à vos risques et périls. Nous ne pourrons en aucun cas être tenus
pour responsables des dommages éventuels provoqués par l’overclocking.
48
En raison de limitations dues au système d'exploitation, la capacité de mémoire utilisée sous
Windows® 32-bit peut être inférieure à 4 Go. Cette limitation ne concerne pas les systèmes
d'exploitation Windows® 64-bit. Vous pouvez utiliser ASRock XFast RAM pour utiliser la
mémoire dont Windows® ne peut se servir.
Page 51
Z87M OC Formula
1.3 Conguration des cavaliers (Jumpers)
L’illustration ci-dessous vous renseigne sur la conguration des cavaliers (jumpers).
Lorsque le capuchon du cavalier est installé sur les broches, le cavalier est ‘court-circuité’.
Si le capuchon du cavalier n’est pas installé sur les broches, le cavalier est ‘ouvert’.
L’illustration représente un cavalier à 3 broches dont les broches 1 et 2 sont «courtcircuitées» si un capuchon de cavalier est posé sur ces 2 broches.
Cavalier Clear CMOS
(CLRCMOS1)
(voir p.1, No. 22)
CLRCMOS1 vous permet d’eacer les donnés de la CMOS. Pour eacer les
paramètres du système et rétablir les valeurs par défaut, veuillez éteindre votre
ordinateur et débrancher son cordon d’alimentation. Patientez 15 secondes, puis
utilisez un capuchon de cavalier pour court-circuiter la broche 2 et la broche 3 sur
CLRCMOS1 pendant 5 secondes. Toutefois, n’eacez pas la CMOS immédiatement
après avoir mis à jour le BIOS. Si vous avez besoin d’eacer les données CMOS
après une mise à jour du BIOS, vous devez tout d’abord redémarrer le système,
puis l’éteindre avant de procéder à l’eacement de la CMOS. Veuillez noter que les
paramètres mot de passe, date, heure et prol de l’utilisateur seront uniquement
eacés en cas de retrait de la pile de la CMOS.
Fonction Clear CMOSPar défaut
Le bouton Clear CMOS possède la même fonction que le cavalier (jumper) Clear CMOS.
49
49
Français
Page 52
1.4 Embases et connecteurs de la carte mère
1
Les embases et connecteurs situés sur la carte NE SONT PAS des cavaliers. Ne placez JAMAIS
de capuchons de cavaliers sur ces embases ou connecteurs. Placer un capuchon de cavalier sur
ces embases ou connecteurs endommagera irrémédiablement votre carte mère.
Français
Embase du panneau système
(PANNEAU1 à 9 broches)
(voir p.1, No. 17)
PWRBTN (bouton d’alimentation):
pour brancher le bouton d’alimentation du panneau frontal du châssis. Vous pouvez congurer
la façon dont votre système doit s’arrêter à l’aide du bouton de mise en marche.
RESET (bouton de réinitiélisation):
pour brancher le bouton de réinitialisation du panneau frontal du châssis. Appuyez
sur le bouton de réinitialisation pour redémarrer l’ordinateur en cas de plantage ou de
dysfonctionnement au démarrage.
PLED (LED d’alimentation du système) :
pour brancher le témoin d’état de l’alimentation du panneau frontal du châssis. Le LED est
allumé lorsque le système fonctionne. Le LED clignote lorsque le système se trouve en mode
veille S1/S3. Le LED est éteint lorsque le système se trouve en mode veille S4 ou hors tension (S5).
HDLED (LED d’activité du disque dur) :
pour brancher le témoin LED d’activité du disque dur du panneau frontal du châssis. Le LED
est allumé lorsque le disque dur lit ou écrit des données.
La conception du panneau frontal peut varier en fonction du châssis. Un module de panneau
frontal est principalement composé d'un bouton de mise en marche, bouton de réinitialisation,
LED d’alimentation, LED d’activité du disque dur, haut-parleur etc. Lorsque vous reliez le
module du panneau frontal de votre châssis sur cette embase, veillez à parfaitement faire
correspondre les ls et les broches.
PLED+
PLED-
HDLED-
HDLED+
PWRBTN#
GND
RESET#
GND
GND
Branchez le bouton de
mise en marche, le bouton
de réinitialisation et le
témoin d’état du système
présents sur le châssis
sur cette embase en
respectant la conguration
des broches illustrée
ci-dessous. Repérez
les broches positive et
négative avant de brancher
les câbles.
50
Page 53
Z87M OC Formula
1
PLED+
PLED+
PLED-
DUMMY
GND
GND
P+
P-
USB_PWR
P+
P-
USB_PWR
1
1
Embase LED
d’alimentation
(PLED1 à 3 broches)
(voir p.12, No. 16)
Embases USB 2.0
(USB2_3 à 9 broches)
(voir p.1, No. 23)
(USB4_5 à 9 broches)
(voir p.1, No. 24)
(USB6)
(voir p.1, No. 9)
Veuillez brancher le
LED d’alimentation du
châssis sur cette embase
pour indiquer l’état
d’alimentation du système.
Ces six connecteurs
SATA3 sont compatibles
avec les câbles de données
SATA pour les appareils de
stockage internes avec un
taux de transfert maximal
de 6,0 Go/s.
SATA3_0_1SATA3_4_5SATA3_2_3
En plus des deux ports
USB 2.0 sur le panneau E/S,
cette carte mère est dotée
de deux embases et d’un
port. Chaque embase USB
2.0 peut prendre en charge
deux ports.
Embases USB 3.0
(USB3_6_7 à 19 broches)
(voir p.11, No. 10)
Vbus
IntA_PA_SSRX-
IntA_PA_SSRX+
GND
IntA_PA_SSTX-
IntA_PA_SSTX+
GND
IntA_PA_D-
IntA_PA_D+
VbusVbus
IntA_PB_SSRX-
IntA_PB_SSRX+
GND
IntA_PB_SSTX-
IntA_PB_SSTX+
GND
IntA_PB_D-
IntA_PB_D+
Dummy
En plus des six ports
USB 3.0 sur le panneau
E/S, cette carte mère
est dotée d’une embase
supplémentaire. Chaque
embase USB 3.0 peut
prendre en charge deux
ports.
51
51
Français
Page 54
Embase audio du panneau
J_SENSE
OUT2_L
1
MIC_RET
PRESENCE#
GND
OUT2_R
MIC2_R
MIC2_L
OUT_RET
1
SPEAKER
GND
OL
frontal
(HD_AUDIO1 à 9
broches)
Cette embase sert au
branchement des appareils
audio au panneau audio
frontal.
(voir p.1, No. 29)
1. L’audio haute dénition prend en charge la technologie Jack Sensing (détection de la che),
mais le panneau grillagé du châssis doit être compatible avec la HDA pour fonctionner
correctement. Veuillez suivre les instructions gurant dans notre manuel et dans le manuel
du châssis pour installer votre système.
2. Si vous utilisez un panneau audio AC’97, veuillez le brancher sur l’embase audio du panneau
frontal en procédant comme suit :
A. branchez Mic_IN (MIC) sur MIC2_L.
B. branchez Audio_R (RIN) sur OUT2_R et Audio_L (LIN) sur OUT2_L.
C. branchez la mise à terre (GND) sur mise à terre (GND).
D. MIC_RET et OUT_RET sont exclusivement réservés au panneau audio HD. Il est inutile
de les brancher avec le panneau audio AC’97.
E. Pour activer le micro frontal, sélectionnez l’onglet «FrontMic» du panneau de contrôle
Realtek et réglez le paramètre «Volume d’enregistrement».
Français
52
Embase du haut-parleur
du châssis
(SPEAKER1 à 4 broches)
(voir p.1, No. 15)
Connecteurs du châssis
et de l’alimentation du
ventilateur
(CHA_FAN1 à 4 broches)
(voir p.1, No. 27)
(CHA_FAN2 à 3 broches)
(voir p.1, No. 26)
(CHA_FAN3 à 3 broches)
(voir p.1, No. 11)
(PWR_FAN1 à 3 broches)
(voir p.1, No. 30)
DUMMY
+5V
+12V
CHA_FAN_SPEED
FAN_SPEED_CONTR
DUMMY
Veuillez brancher le hautparleur du châssis sur cette
embase.
Veuillez brancher les câbles
du ventilateur sur les
connecteurs du ventilateur,
puis reliez le l noir à la
broche de mise à terre.
Page 55
Z87M OC Formula
CPU_FAN_SPEED
N_SPEED
FA
4
8
1
RRI#1
DUMMY
1
Connecteurs du
ventilateur du processeur
(CPU_FAN1 à 4 broches)
(voir p.1, No. 3)
Cette carte mère est dotée
d’un connecteur pour
ventilateur de processeur
(Quiet Fan) à 4 broches.
Si vous envisagez de
connecter un ventilateur
de processeur à 3 broches,
veuillez le brancher sur la
Broche 1-3.
Cette carte mère est
dotée d’un connecteur
d’alimentation ATX à 24
broches. Pour utiliser une
alimentation ATX à 20
broches, veuillez eectuer
les branchements sur la
Broche 1 et la Broche 13.
Cette carte mère est
dotée d’un connecteur
d’alimentation ATX 12V
à 8 broches. Pour utiliser
une alimentation ATX à 4
broches, veuillez eectuer
les branchements sur la
Broche 1 et la Broche 5.
Embase pour module
infrarouge
(IR1 à 5 broches)
(voir p.1, No. 28)
Embase pour port série
(COM1 à 9 broches)
(voir p.1, No. 25)
IRTX
IRRX
RRXD1
DDTR#1
TTXD1
DDCD#1
+5VSB
GND
DDSR#1
GND
CCTS#1
RRTS#1
Cette embase prend en charge un
module sans-l d’émission et de
réception infrarouge optionnel.
Cette embase COM1 prend
en charge un module de
port série.
53
53
Français
Page 56
1.5 Boutons intelligents
AB
La carte mère est équipée de trois boutons intelligents: Bouton de mise en marche,
bouton de réinitialisation et bouton d’eacement CMOS permettant aux utilisateurs
d’allumer/éteindre le système, de réinitialiser le système ou d’eacer les valeurs CMOS
en toute simplicité.
Français
Bouton de mise en marche
(PWRBTN)
(voir p.1, No. 18)
Bouton de réinitialisation
(RSTBTN)
(voir p.1, No. 19)
Bouton Clear CMOS
(CLRCBTN)
(voir p.1, No. 20)
Cette fonction est uniquement disponible lorsque l’ordinateur est éteint et son cordon
d’alimentation débranché.
Le bouton de mise en
marche permet aux
utilisateurs d’allumer le
système rapidement.
Le bouton de
réinitialisation permet aux
utilisateurs de réinitialiser
le système rapidement.
Le bouton d’eacement
Clear CMOS permet
aux utilisateurs d’eacer
les valeurs CMOS
rapidement.
Si le mode Lent est activé,
le processeur fonctionne à
une fréquence moindre.
Le sélecteur du BIOS
permet au système de
démarrer depuis le BIOS
A ou le BIOS B.
Cette carte mère est dotée de deux BIOS – un BIOS principal (BIOS_A), et un BIOS de
sauvegarde (BIOS_B) – ce qui permet d’optimiser la protection et la stabilité du système. En
règle générale, le système utilise le BIOS principal. Toutefois, si le BIOS principal venait à
être corrompu ou endommagé, placez simplement le sélecteur en position «B» et le BIOS de
secours prendra automatiquement le relais au redémarrage du système. Après cela, utilisez
«Secure Backup UEFI» depuis l’utilitaire de conguration UEFI pour copier les chiers BIOS
vers le BIOS principal et rétablir le fonctionnement normal du système. Par souci de sécurité
du système, l’utilisateur ne peut pas mettre à jour le BIOS de secours manuellement. Pour
identier le BIOS actif, l’utilisateur peut consulter les témoins LED du BIOS (LED_BIOS_A ou
LED_BIOS_B).
Le mode LN2 aide à éliminer
le bogue associé au démarrage
à froid des processeurs en cas
d’overclocking extrême au
nitrogène liquide.
55
55
Français
Page 58
1 Introduzione
Grazie per aver acquistato la scheda madre ASRock Z87M OC Formula, una scheda
madre adabile prodotta secondo il severo e continuo controllo di qualità ASRock.
La scheda madre ore eccellenti prestazioni con un design robusto che si adatta
all'impegno di ASRock di orire sempre qualità e durata.
Dato che le speciche della scheda madre e del soware BIOS possono essere aggiornate, il
contenuto di questa documentazione sarà soggetto a variazioni senza preavviso. Nel caso di
eventuali modiche della presente documentazione, la versione aggiornata sarà disponibile sul
sito Web di ASRock senza ulteriore preavviso. Per il supporto tecnico correlato a questa scheda
madre, visitare il nostro sito Web per informazioni speciche relative al modello attualmente in
uso. È possibile trovare l'elenco di schede VGA più recenti e di supporto di CPU anche sul sito
Web di ASRock. Sito Web di ASRock http://www.asrock.com.
1.1 Contenuto della confezione
• Scheda madre ASRock Z87M OC Formula (formato Micro ATX)
• Guida rapida di installazione di ASRock Z87M OC Formula
• CD di assistenza ASRock Z87M OC Formula
• 4 x cavi dati Serial ATA (SATA) (opzionali)
• 10 x Supporti OC
• Composto termico GELID Solution GC-Extreme
• 1 vite per modulo WiFi
• 1 vite mSATA
Italiano
56
Page 59
1.2 Speciche
Z87M OC Formula
Piattaforma
Stile superiore
Kit OC
Formula
CPU
• Fattore di forma Micro ATX
• Design condensatore Premium Gold (condensatori a
conduttore in polimero di alta qualità realizzati al 100% in
Giappone)
• Home Cloud
• Purity Sound
• Ingresso HDMI
Kit alimentazione OC Formula
• 12 Power Phase Design
• Alimentazione Digi
• Dual-Stack MOSFET (DSM)
• MFC (Multiple Filter Cap) (Filtra rumori diversi con 3
condensatori diversi: condensatore solido DIP, POSCAP e
MLCC)
• Bobina in lega di alta qualità (Riduce le perdite principali del
70% rispetto alle bobine in polvere di acciaio)
Kit connettore OC Formula
• Connettore alimentazione ad alta densità (8 pin)
• 15μGold Finger (attacchi CPU, attacchi per memorie e PCIE
• 2 alloggi PCI Express 3.0 x16 (PCIE1/PCIE3:singolo in
modalità x16 (PCIE1); doppio in modalità x8 (PCIE1) / x8
(PCIE3))
• 1 slot PCI Express 2.0 x4
• 1 alloggio PCI Express 2.0 x1
• 1 slot half mini-PCI Express
• 1 slot mSATA/mini-PCI Express
* Lo slot mSATA/mini-PCI Express è condiviso con la porta
SATA3_4.
• Supporta AMD Quad CrossFireXTM e CrossFireXTM
• Supporta NVIDIA® Quad SLITMe SLI
• La videograca integrata della scheda video HD Intel® e le
uscite VGA possono essere supportate soltanto con processori
con GPU integrata.
• Supporta la videograca integrata della scheda video HD Intel®:
Intel® Quick Sync Video con AVC, MVC (S3D) e MPEG-2
Full HW Encode1, Intel® InTruTM 3D, tecnologia Intel® Clear
Video HD, Intel® InsiderTM, Intel® HD Graphics 4400/4600
• Pixel Shader 5.0, DirectX 11.1
• Memoria condivisa max. 1792 MB
• Doppia uscita VGA:supporto di porte HDMI e DisplayPort
tramite controller display indipendenti
• Supporta tecnologia HDMI con risoluzione max. no a 4K x
2K (4096x2304) a 24 Hz
• Supporta DisplayPort con risoluzione max. no a 4K x 2K
(4096x2304) a 24 Hz
• Supporta Auto Lip Sync, Deep Color (12 bpc), xvYCC e HBR
(High Bit Rate Audio) con HDMI (è necessario un monitor
conforme ad HDMI)
• Supporto della funzione HDCP con le porte HDMI e
DisplayPort
• Supporto di riproduzione Full HD 1080p Blu-ray (BD) con le
porte HDMI e DisplayPort
TM
58
Page 61
Z87M OC Formula
Audio
LAN
I/O pannello
posteriore
• Audio HD a 7.1 canali con Content Protection (codec audio
Realtek ALC1150)
• 1 x porta LAN RJ-45 con LED (ACT/LINK LED e SPEED
LED)
• 1 x pulsante per azzerare la CMOS
• Jack audio HD: altoparlante posteriore/centrale/basso/ingresso
linea/altoparlante anteriore/microfono
Italiano
59
59
Page 62
Archiviazione
• 6 connettori SATA3 6,0 Gb/s, con supporto funzioni RAID
(RAID 0, RAID 1, RAID 5, RAID 10, Intel Rapid Storage
Technology 12 ed Intel Smart Response Technology), NCQ,
AHCI e Hot Plug
• 1 connettore eSATA, con supporto funzioni RAID (RAID 0,
RAID 1, RAID 5, RAID 10, Intel Rapid Storage Technology 12
e Intel Smart Response Technology), NCQ, AHCI e Hot Plug
* Il connettore eSATA è condiviso con la porta SATA3_1.
Italiano
Connettore
Funzione BIOS
• 1 x header IR
• 1 x header porta COM
• 1 x header LED di alimentazione
• 2 x connettori ventola CPU (1 x 4 pin, 1 x 3 pin)
• 3 x connettori ventola chassis (1 x 4 pin, 2 x 3 pin)
• 1 x connettore ventola alimentazione (3 pin)
• 1 x connettore alimentazione ATX a 24 pin
• 1 x connettori alimentazione da 12 V a 8 pin
(Connettore di alimentazione ad alta densità)
• 1 x connettore audio pannello anteriore
• 2 x header USB 2.0 (supporto 4 porte USB 2.0)
• 1 x USB 2.0 verticale tipo A
• 1 x header USB 3.0 (supporta 2 porte USB 3.0)
• 1 x interruttore d’alimentazione con LED
• 1 x interruttore di ripristino con LED
• 1 x pulsante per azzerare la CMOS
• 1 x Post Status Checker (PSC)
• 1 x interruttore modalità lenta
• 1 x interruttore modalità LN2
• 1 x interruttore di selezione BIOS
• 2 x 64Mb AMI UEFI Legal BIOS con supporto interfaccia
• Driver, Utilità, soware antivirus (versione di prova), versione
di prova di CyberLink MediaEspresso 6.5, browser e barra degli
strumenti Google Chrome, Start8, MeshCentral, Splashtop
Streamer
* Per informazioni dettagliate sul prodotto, visitare il nostro sito Web: http://www.asrock.com
Prestare attenzione al potenziale rischio previsto nella pratica di overclocking, inclusa la
regolazione delle impostazioni nel BIOS, l'applicazione di tecnologia di Untied Overclocking o
l'utilizzo di strumenti di overclocking di terze parti. L'overclocking può inuenzare la stabilità
del sistema o perno provocare danni ai componenti e ai dispositivi del sistema. Occorre
eseguirlo a proprio rischio e spese. Non ci riterremo responsabili per possibili danni provocati da
overclocking.
A causa della limitazione, l'eettiva dimensione della memoria può essere inferiore a 4 GB
per riservare l'uso del sistema ai sistemi operativi di Windows® a 32 bit. I sistemi operativi
Windows® a 64 bit non possiedono tali limitazioni. È possibile utilizzare la RAM XFast di
ASRock per utilizzare la memoria che Windows® non può utilizzare.
61
61
Italiano
Page 64
Italiano
1.3 Impostazione jumper
L'illustrazione mostra in che modo vengono impostati i jumper. Quando il cappuccio
del jumper è posizionato sui pin, il jumper è "cortocircuitato". Se sui pin non è
posizionato alcun cappuccio del jumper, il jumper è "aperto". L'illustrazione mostra
un jumper a 3 pin i cui pin1 e pin2 sono "cortocircuitati" quando un cappuccio del
jumper è posizionato su questi 2 pin.
Jumper per azzerare la
CMOS
(CLRCMOS1)
(vedere pag. 1, n. 22)
CLRCMOS1 consente di azzerare i dati presenti nella CMOS. Per azzerare e
reimpostare i parametri del sistema alla congurazione predenita, spegnere il
computer e scollegare il cavo di alimentazione dalla rete. Dopo aver atteso 15
secondi, utilizzare un cappuccio del jumper per cortocircuitare il pin2 e il pin3
su CLRCMOS1 per 5 secondi. Tuttavia, non azzerare la CMOS subito dopo aver
aggiornato il BIOS. Se è necessario azzerare la CMOS dopo l'aggiornamento del
BIOS, è necessario riavviare prima il sistema e in seguito spegnerlo prima di eseguire
l'operazione di azzeramento della CMOS. La password, la data, l'ora e il prolo
predenito dell'utente saranno azzerati solo se viene rimossa la batteria della CMOS.
Azzerare la CMOSpredenito
62
Il pulsante per azzerare la CMOS ha la stessa funzione del jumper per azzerare la CMOS.
Page 65
1.4 Header e connettori sulla scheda
Gli header e i connettori sulla scheda NON sono jumper. NON posizionare cappucci del jumper
su questi header e connettori. Il posizionamento di cappucci del jumper su header e connettori
provocherà danni permanenti alla scheda madre.
Z87M OC Formula
Header sul pannello del
sistema
(PANEL1 a 9 pin)
(vedere pag. 1, n. 17)
PWRBTN (interruttore di alimentazione):
collegare all'interruttore dell'alimentazione sul pannello anteriore dello chassis. È possibile
congurare il modo in cui spegnere il sistema utilizzando l'interruttore dell'alimentazione.
RESET (interruttore di reset):
collegare all'interruttore di reset sul pannello anteriore dello chassis. Premere l'interruttore
di reset per riavviare il computer se il computer si blocca e non riesce ad eseguire un normale
riavvio.
PLED (LED alimentazione del sistema):
collegare all'indicatore di stato dell'alimentazione sul pannello anteriore dello chassis. Il LED
è acceso quando il sistema è in funzione. Il LED continua a lampeggiare quando il sistema si
trova nello stato di sospensione S1/S3. Il LED è spento quando il sistema si trova nello stato di
sospensione S4 o quando è spento (S5).
HDLED (LED di attività disco rigido):
collegare al LED di attività disco rigido sul pannello anteriore dello chassis. Il LED è acceso
quando il disco rigido sta leggendo o scrivendo dati.
Il design del pannello anteriore può cambiare a seconda dello chassis. Un modulo di pannello
anteriore è composto principalmente da interruttore di alimentazione, interruttore di reset,
LED di alimentazione, LED di attività disco rigido, altoparlante, ecc. Quando si collega il
modulo del pannello anteriore dello chassis a questo header, accertarsi che le assegnazioni del
lo e le assegnazioni del pin corrispondano correttamente.
1
PLED+
PLED-
HDLED-
HDLED+
PWRBTN#
GND
RESET#
GND
GND
Collegare l'interruttore
dell'alimentazione,
l'interruttore di reset e
l'indicatore dello stato del
sistema sullo chassis su
questo header secondo
la seguente assegnazione
dei pin. Annotare i pin
positivi e negativi prima di
collegare i cavi.
Italiano
63
63
Page 66
Header LED di
1
PLED+
PLED+
PLED-
DUMMY
GND
GND
P+
P-
USB_PWR
P+
P-
USB_PWR
1
1
alimentazione
(PLED1 a 3 pin)
(vedere pag. 12, n. 16)
Collegare il LED di
alimentazione chassis a
questo header per
indicare
lo stato di alimentazione
del sistema.
Italiano
Connettori Serial ATA3
(SATA3_0_1:
consultare pag.1, N. 12)
(SATA1_2_3:
vedere pag. 1, n. 13)
(SATA3_4_5:
vedere pag. 1, n. 14)
Header USB 2.0
(USB2_3 a 9 pin)
(vedere pag. 1, n. 23)
(USB4_5 a 9 pin)
(vedere pag. 1, n. 24)
(USB6)
(vedere pag. 1, n. 9)
Header USB 3,0
(USB3_6_7 a 19 pin)
(vedere pag. 11, N. 10)
SATA3_0_1SATA3_4_5SATA3_2_3
Vbus
IntA_PA_SSRX-
IntA_PA_SSRX+
IntA_PA_SSTX-
IntA_PA_SSTX+
IntA_PA_D-
IntA_PA_D+
Questi sei connettori
SATA3 supportano cavi
dati SATA per dispositivi
di archiviazione interna,
con una velocità di
trasferimento dati no a 6,0
Gb/s.
Oltre alle due porte USB
2.0 nel pannello I/O, la
scheda madre dispone di
due connettori e una porta.
Ciascun header USB 2.0
può supportare due porte.
VbusVbus
IntA_PB_SSRX-
IntA_PB_SSRX+
GND
IntA_PB_SSTX-
GND
IntA_PB_SSTX+
GND
IntA_PB_D-
GND
IntA_PB_D+
Dummy
Oltre alle sei porte USB
3.0 nel pannello I/O, la
scheda madre dispone di
un connettore. Ciascun
header USB 3.0 può
supportare due porte.
64
Page 67
Z87M OC Formula
J_SENSE
OUT2_L
1
MIC_RET
PRESENCE#
GND
OUT2_R
MIC2_R
MIC2_L
OUT_RET
1
DUMMY
SPEAKER
GND
OL
Header audio pannello
anteriore
(AUDIO1_HD a 9 pin)
(vedere pag. 1, n. 29)
1. L'audio ad alta denizione supporta le funzioni Jack sensing, ma il lo del pannello sullo
chassis deve supportare HDA per funzionare correttamente. Seguire le istruzioni presenti nel
nostro manuale e nel manuale dello chassis per installare il sistema.
2. Se si utilizza un pannello audio AC’97, installarlo sull'header audio del pannello anteriore
seguendo le fasi di seguito:
A. Collegare Mic_IN (MIC) a MIC2_L.
B. Collegare Audio_R (RIN) a OUT2_R e Audio_L (LIN) a OUT2_L.
C. Collegare Ground (GND) a Ground (GND).
D. MIC_RET e OUT_RET servono soltanto per il pannello audio HD. Non è necessario
collegarli per il pannello audio AC’97.
E. Per attivare il microfono anteriore, andare alla scheda “FrontMic” nel pannello di controllo
Realtek e regolare il “Volume di registrazione”.
Header altoparlante chassis
+5V
(SPEAKER1 a 4 pin)
DUMMY
Questo header serve a
collegare i dispositivi
audio al pannello audio
anteriore.
Collegare l'altoparlante
dello chassis a questo
header.
(vedere pag. 1, n. 15)
Connettori ventola dello
chassis e di alimentazione
(CHA_FAN1 a 4 pin)
(vedere pag. 1, n. 27)
(CHA_FAN2 a 3 pin)
(vedere pag. 1, n. 26)
(CHA_FAN3 a 3 pin)
(vedere pag. 1, n. 11)
(PWR_FAN1 a 3 pin)
(vedere pag. 1, n. 30)
+12V
CHA_FAN_SPEED
FAN_SPEED_CONTR
Collegare i cavi della
ventola ai connettori della
ventola e far corrispondere
il lo nero al pin di terra.
65
65
Italiano
Page 68
Connettori della ventola
CPU_FAN_SPEED
N_SPEED
FA
4 1
8 5
RRI#1
1
della CPU
(CPU_FAN1 a 4 pin)
(vedere pag. 1, n. 3)
(CPU_FAN2 a 3 pin)
(vedere pag. 1, n. 2)
4 3 2 1
+12V
N_SPEED_CONTROL
CPU_FA
GND
+12V
GN D
Questa scheda madre è
dotata di un connettore
per la ventola della CPU
(Ventola silenziosa) a 4 pin.
Se si decide di collegare
una ventola della CPU a 3
pin, collegarla al pin 1-3.
Italiano
Connettore di
alimentazione ATX
(ATXPWR1 a 24 pin)
(vedere pag. 1, n. 8)
Connettore di
alimentazione ATX da 12 V
(ATX12V1 a 8 pin)
(vedere pag. 1, n. 1)
Header modulo infrarossi
(IR1 a 5 pin)
(vedere pag. 1, n. 28)
Header porta seriale
(COM1 a 9 pin)
(vedere pag. 1, n. 25)
1
IRTX
IRRX
RRXD1
DDTR#1
TTXD1
DDCD#1
+5VSB
GND
DDSR#1
GND
DUMMY
CCTS#1
RRTS#1
Questa scheda madre è
dotata di un connettore
di alimentazione ATX
a 24 pin. Per utilizzare
un'alimentazione ATX a
20 pin, collegarla lungo il
pin1 e il pin 13.
Questa scheda madre è
dotata di un connettore
di alimentazione ATX da
12 V a 8 pin. Per utilizzare
un'alimentazione ATX a
4 pin, collegarla lungo il
pin1 e il pin 5.
Questo header supporta un
modulo infrarossi di trasmissione
e ricezione wireless opzionale.
Questo header COM1
supporta un modulo di
porta seriale.
66
Page 69
Z87M OC Formula
AB
1.5 Interruttori intuitivi
La scheda madre è dotata di tre interruttori intuitivi: Interruttore di alimentazione,
interruttore di reset e pulsante per azzerare la CMOS che consentono all'utente di
accendere/spegnere rapidamente il sistema, ripristinarlo e azzerare i valori della
CMOS.
Interruttore d’alimentazione
(PWRBTN)
(vedere pag. 1, n. 18)
Interruttore di ripristino
(RSTBTN)
(vedere pag. 1, n. 19)
Tasto Cancella CMOS
(CLRCBTN)
(vedere pag. 1, n. 20)
Questa funzione è operativa solo quando si spegne il computer e si scollega l'alimentatore.
Interruttore modalità
lenta(SLOWMODE1)
(vedere pag. 1 n. 6)
Interruttore selezione
BIOS(BIOS_SEL1)
(vedere pag. 1, n. 21)
Power
Reset
OFF
ON
L’interruttore
d’alimentazione consente
di accendere/spegnere
rapidamente il sistema.
L’interruttore di ripristino
consente di ripristinare
rapidamente il sistema.
Il tasto Cancella CMOS
consente agli utenti di
cancellare rapidamente i
valori CMOS.
Se la modalità Lenta
è attiva, il processore
funziona alla frequenza
più bassa.
L'interruttore di selezione
BIOS consente di riavviare
il sistema dal BIOS A o dal
BIOS B.
Italiano
Questa scheda madre è dotata di due chip BIOS, un BIOS principale (BIOS_A) e un BIOS di
backup (BIOS_B), che migliorano la sicurezza e la stabilità del sistema. Il sistema funziona
normalmente sul BIOS principale. Tuttavia, se il BIOS principale è corrotto o danneggiato,
basta semplicemente posizionare l'interruttore di selezione su "B" e il BIOS secondario si
occuperà dell'avvio successivo del sistema. Quindi, usare "Secure Backup UEFI" in UEFI Setup
Utility per duplicare una copia dei le BIOS sul BIOS primario per garantire il funzionamento
normale del sistema. Per questioni di sicurezza, gli utenti non sono in grado di aggiornare il
BIOS di backup manualmente. Gli utenti possono fare riferimento ai LED BIOS (BIOS_A_LED
o BIOS_B_LED) per identicare quale BIOS è attualmente attivato.
67
67
Page 70
Interruttore modalità LN2
(LN2MODE1)
(vedere pag. 1, n. 7)
OFF
ON
La modalità LN2 aiuta ad
eliminare i problemi di bug
dovuti all'accensione a freddo
nei processori, durante
l'overclock estremo ad azoto
liquido.
Italiano
68
Page 71
Z87M OC Formula
1 Introducción
Gracias por adquirir la placa base ASRock Z87M OC Formula, una placa base able
fabricada siguiendo el sistemáticamente estricto control de calidad de ASRock. Ofrece
un rendimiento excelente con un diseño resistente de acuerdo con el compromiso de
calidad y resistencia de ASRock.
Ya que las especicaciones de la placa base y el soware del BIOS podrán ser actualizados, el
contenido que aparece en esta documentación estará sujeto a modicaciones sin previo aviso.
Si esta documentación sufre alguna modicación, la versión actualizada estará disponible
en el sitio web de ASRock sin previo aviso. Si necesita asistencia técnica relacionada con esta
placa base, visite nuestro sitio web para obtener información especíca sobre el modelo que esté
utilizando. Podrá encontrar las últimas tarjetas VGA, así como la lista de compatibilidad de la
CPU, en el sitio web de ASRock. Sitio web de ASRock http://www.asrock.com.
1.1 Contenido del paquete
• Placa base ASRock Z87M OC Formula (factor de forma Micro-ATX)
• Guía de instalación de la placa base ASRock Z87M OC Formula
• CD de soporte de la placa base ASRock Z87M OC Formula
• 4 cables de datos Serie ATA (SATA) (Opcional)
• 10 soportes OC
• Pasta Térmica GELID GC-Extreme
• 1 x Tornillo del módulo WiFi
• 1 x Tornillo mSATA
69
69
Español
Page 72
1.2 Especicaciones
Español
Plataforma
A-Style
Kit de OC
Formula
• Factor de forma Micro ATX
• Diseño de los Condensadores: Premium Gold (Condensadores
de polímero conductor, de alta calidad, 100% fabricados en
Japón)
• Home Cloud
• Purity Sound
• Entrada HDMI
Kit de alimentación de OC Formula
• Diseño de 12 fases de alimentación
• Digi Power
• MOSFET de doble pila (DSM)
• Multiple Filter Cap (MFC) (diferentes ruidos de ltros
mediante 3 condensadores diferentes: condensador sólido DIP,
POSCAP y MLCC)
• Premium Alloy Choke (reduce el 70% de pérdida de energía en
el núcleo en comparación con Iron Powder Choke)
Kit de conectores de OC Formula
• Conector de alimentación de alta densidad (8 pines)
• 15μGold Finger (sockets de CPU, sockets de memoria y ranuras
PCIE x16)
• Ranura sin distorsión
Kit de refrigeración de OC Formula
• Circuito impreso (PCB) de 8 capas
• 4 unidades de 2oz de cobre
• Compuesto térmico GC-Extreme de GELID Solutions
TM
70
CPU
Conjunto de
chips
• Compatible con 4.ª Generación de Intel® CoreTM i7 / i5 / i3 /
Xeon® / Pentium® / Celeron® en Paquete LGA1150
• Compatible con la tecnología de Intel® Turbo Boost 2.0
• Compatible con CPU serie K desbloqueada de Intel®
• Compatible con overclocking de rango completo BCLK de
• Capacidad máxima de la memoria del sistema: 32GB
• Compatible con Extreme Memory Prole (XMP)1.3/1.2 de
Intel®
• Ranura sin distorsión
• 2 ranuras PCI Express 3.0 x16 (PCIE1/PCIE3:Una a x16
(PCIE1); dos a x8 (PCIE1) / x8 (PCIE3)
• 1 x Ranura PCI Express 2.0 x4
• 1 ranura PCI Express 2.0 x1
• 1 x Ranura mini-PCI Express media
• 1 x Ranura mSATA/mini-PCI Express
* La ranura mSATA/mini-PCI Express se comparte con el
puerto SATA3_4.
• Compatible con AMD Quad CrossFireXTM y CrossFireXTM
• Compatible con NVIDIA® Quad SLITM y SLI
• La Tecnología visual integrada de grácos HD de Intel® y las
salidas de VGA son compatibles únicamente con procesadores
con GPU integrado.
• Compatible con la Tecnología visual integrada de grácos HD
de Intel®: Intel® Quick Sync Video con AVC, MVC (S3D) y
MPEG-2 Full HW Encode1, Intel® InTruTM 3D, Intel® Clear
Video HD Technology, Intel® InsiderTM, Intel® HD Graphics
4400/4600
• Pixel Shader 5.0, DirectX 11.1
• Memoria compartida máxima: 1792MB
• Salida VGA dual:compatible con puertos HDMI y DisplayPort
mediante controladores de pantalla independientes
• Admite la tecnología HDMI con una resolución máxima de 4K
x 2K (4096x2304) a 24 Hz
• Admite la tecnología DisplayPort con una resolución máxima
de 4K x 2K (4096x2304) a 24 Hz
• Compatible con Auto Lip Sync, Deep Color (12bpc), xvYCC y
HBR (audio de alta velocidad de bits) con HDMI (requiere un
monitor compatible con HDMI)
• Compatible con función HDCP con puertos HDMI y
DisplayPort
• Compatible con reproducción Blu-ray (BD) Full HD de 1080p
con puertos HDMI y DisplayPort
TM
71
71
Español
Page 74
Audio
• 7.1 Audio CH HD con Protección de contenido (Realtek
ALC1150 Audio Codec)
• Compatible con audio Blu-ray Premium
• Compatible con Purity Sound™
- 115dB SNR DAC con amplicador diferencial
- Amplicador de auriculares de alta calidad TI® NE5532
(admite auriculares de hasta 600 ohmios)
- Tecnología Direct Drive
- Cubierta protectora de EMI (interferencias electromagnéticas)
- Protección de aislamiento PCB (circuito impreso)
• Compatible con DTS Connect
Español
LAN
Panel trasero
I/O
• LAN Gigabit 10/100/1000 Mb/s
• Giga PHY Intel® I217V
• Compatible con la Tecnología Remote Wake de Intel®
• Compatible con Wake-On-LAN
• Compatible con Ethernet de consumo eciente de energía
802.3az
• Compatible con PXE
• 1 puerto de ratón/teclado PS/2
• 1 puerto de salida HDMI
• 1 puerto de entrada HDMI
• 1 DisplayPort
• 1 puerto de salida SPDIF óptica
• 1 conector eSATA
• 2 puertos USB 2.0
• 4 x Puertos USB 3.0 (Intel® Z87) (concentrador ASMedia)
• 2 x Puertos USB 3.0 (Intel® Z87)
• 1 puerto LAN RJ-45 con LED (ACT/LINK LED y SPEED LED)
• 1 botón de borrado CMOS
• Conector de audio HD: Altavoz trasero / Central / Graves /
Entrada de línea / Altavoz frontal / Micrófono
72
Page 75
Z87M OC Formula
Almacenamiento
Conectores
• 6 x Conectores SATA3 de 6 Gb/s, compatibilidad con RAID
(RAID 0, RAID 1, RAID 5, RAID 10, Intel Rapid Storage
Technology 12 e Intel Smart Response Technology), NCQ,
AHCI y conexión en caliente
• 1 x Conector eSATA, compatibilidad con RAID (RAID 0,
RAID 1, RAID 5, RAID 10, Intel Rapid Storage Technology 12
e Intel Smart Response Technology), NCQ, AHCI y conexión
en caliente
* El conector eSATA se comparte con el puerto SATA3_1.
• 1 cabezal IR
• 1 cabezal de puerto COM
• 1 cabezal de indicador LED de alimentación
• 2 conectores de ventilador de la CPU (1 de 4 pines y 1 de 3
pines)
• 3 conectores de ventilador del chasis (1 de 4 pines y 2 de 3
pines)
• 1 conector de ventilador de alimentación (de 3 pines)
• 1 conector de alimentación ATX de 24 pines
• 1 conectores de alimentación de 12V de 8 pines(Conector de
alimentación de alta densidad)
• 1 conector de audio del panel frontal
• 2 cabezales USB 2.0 (compatibles con 4 puertos USB 2.0)
• 1 USB 2.0 vertical de tipo A
• 1 cabezal USB 3.0 (compatible con 2 puertos USB 3.0)
• 1 interruptor de alimentación con indicador LED
• 1 interruptor de reseteo con indicador LED
• 1 botón de borrado CMOS
• 1 mensaje comprobador de estado (Post Status Checker, PSC)
• 1 interruptor del Modo Lento
• 1 interruptor del Modo LN2
• 1 interruptor de selección de BIOS
Español
Función del
BIOS
• 2 BIOS Legal UEFI AMI de 64Mb compatibles con interfaz
gráca de usuario multilingüe (1 BIOS Principal y 1 BIOS de
copia de seguridad)
• Compatible con tecnología UEFI de copia de seguridad segura
• Eventos de reactivación conformes con ACPI 1.1
• Compatible con SMBIOS 2.3.1
• Multiajuste de voltaje de CPU, DRAM, PCH 1,05V, PCH 1,5V
73
73
Page 76
CD de soporte
• Controladores, Utilidades, Soware AntiVirus (Versión de
prueba), Versión de prueba de CyberLink MediaEspresso 6.5,
Explorador y Barra de herramientas de Google Chrome, Start8,
MeshCentral y Splashtop Streamer
Español
Monitor del
• Método de sensor de temperatura de la CPU/Chasis
• Tacómetro del ventilador de alimentación/CPU/Chasis
• Ventilador silencioso de la CPU/Chasis (permite ajustar
automáticamente la velocidad del ventilador del chasis
mediante la temperatura de la CPU)
• Control multivelocidad del ventilador de la CPU/Chasis
• Control del voltaje: +12V, +5V, +3,3V, CPU Vcore
SO
• Compatible con Microso® Windows® 8 / 8 de 64 bits / 7 / 7 de
64 bits
Certicaciones
• FCC, CE, WHQL
• Compatible con ErP/EuP (requiere toma de alimentación
compatible con ErP/EuP)
* Para obtener más información acerca del producto, visite nuestro sitio web: http://www.asrock.com
Tenga en cuenta que existen ciertos riesgos relacionados con el overclocking (sobreaceleración),
incluyendo el ajuste de la conguración del BIOS, aplicando la Tecnología overcloking no
vinculada o utilizando las herramientas de overclocking de tercera parte. El overclocking
podría afectar la estabilidad de su sistema o incluso dañar los componentes y dispositivos de
su sistema. Si lo realiza, todos los riesgos y gastos derivados del overclocking serán de su entera
responsabilidad. No nos hacemos responsables de posibles daños producidos por el overclocking.
74
Debido a las limitaciones, el tamaño real de la memoria podrá ser inferior a 4GB para reservar
espacio para el uso del sistema en sistemas operativos Windows® de 32 bits. Los sitemas
operativos Windows® de 64 bits no tienen estas limitaciones. Podrá utilizar XFast RAM de
ASRock para usar la memoria que Windows® no puede utilizar.
Page 77
Z87M OC Formula
1.3 Instalación de los puentes
La instalación muestra cómo deben instalarse los puentes. Cuando la tapa de puente
se coloca en los pines, el puente queda “Corto”. Si no coloca la tapa de puente en los
pines, el puente queda “Abierto”. La ilustración muestra un puente de 3 pines cuyo pin
1 y pin 2 son “Cortos” cuando se coloca una tapa de puente en estos 2 pines.
Puente de borrado de
CMOS
(CLRCMOS1)
(consulte la pág.1, N.º 22)
CLRCMOS1 le permite borrar los datos del CMOS. Para borrar y restablecer los
parámetros del sistema a los valores predeterminados de instalación, apague el
ordenador y desenchufe el cable de alimentación de la toma de alimentación.
Después de esperar 15 segundos, utilice un tapa de puente para acortar el pin2 y
el pin3 en el CLRCMOS1 durante 5 segundos. Sin embargo, no borre el CMOS
justo después de que haya actualizado el BIOS. Si necesita borrar el CMOS cuando
acabe de actualizar el BIOS, deberá arrancar el sistema primero y, a continuación,
deberá apagarlo antes de que realice el borrado del CMOS. Tenga en cuenta que la
contraseña, la fecha, la hora y el perl de usuario predeterminado serán eliminados
únicamente si se retira la pila del CMOS.
Borrado de CMOSPredeterminado
Español
El botón de borrado CMOS tiene la misma función que el puente de borrado de CMOS.
75
75
Page 78
1.4 Conectores y cabezales incorporados
1
Los cabezales y conectores incorporados NO son puentes. NO coloque tapas de puente sobre
estos cabezales y conectores. Si coloca tapas de puente sobre los cabezales y conectores dañará
de forma permanente la placa base.
Español
Cabezal del panel del sistema
(PANEL1 de 9 pines)
(consulte la pág.1, N.º 17)
PWRBTN (Interruptor de alimentación):
Conéctelo al interruptor de alimentación del panel frontal del chasis. Deberá congurar la
forma en la que su sistema se apagará mediante el interruptor de alimentación.
RESET (Interruptor de reseteo):
Conéctelo al interruptor de reseteo del panel frontal del chasis. Pulse el interruptor de reseteo
para resetear el ordenador si éste está bloqueado y no se puede reiniciar de forma normal.
PLED (Indicador LED de la alimentación del sistema):
Conéctelo al indicador de estado de la alimentación del panel frontal del chasis. El indicador
LED permanece encendido cuando el sistema está funcionando. El indicador LED parpadea
cuando el sistema se encuentra en estado de suspensión S1/S3. El indicador LED se apaga
cuando el sistema se encuentra en estado de suspensión S4 o está apagado (S5).
HDLED (Indicador LED de actividad en el disco duro):
Conéctelo al indicador LED de actividad en el disco duro del panel frontal del chasis. El
indicador LED permanece encendido cuando el disco duro está leyendo o escribiendo datos.
El diseño del panel frontal puede ser diferente dependiendo del chasis. Un módulo de panel
frontal consta principalmente de: interruptor de alimentación, interruptor de reseteo, indicador
LED de alimentación, indicador LED de actividad en el disco duro, altavoz, etc. Cuando
conecte su módulo del panel frontal del chasis a este cabezal, asegúrese de que las asignaciones
de los cables y los pines coinciden correctamente.
PLED+
PLED-
HDLED-
HDLED+
PWRBTN#
GND
RESET#
GND
GND
Conecte el interruptor de
alimentación, restablezca el
interruptor y el indicador
del estado del sistema del
chasis a los valores de este
cabezal, según los valores
asignados a los pines como
se indica a continuación.
Cerciórese de cuáles son
los pines positivos y los
negativos antes de conectar
los cables.
76
Page 79
Z87M OC Formula
1
PLED+
PLED+
PLED-
DUMMY
GND
GND
P+
P-
USB_PWR
P+
P-
USB_PWR
1
1
Cabezal de indicador LED
de alimentación
(PLED1 de 3 pines)
(consulte la pág. 12, N.º
16)
Conectores Serie ATA3
(SATA3_0_1:
consulte la página 1, nº 12)
(SATA1_2_3:
consulte la pág.1, N.º 13)
(SATA3_4_5:
consulte la pág.1, N.º 14)
Cabezales USB 2.0
(USB2_3 de 9 pines)
(consulte la pág.1, N.º 23)
(USB4_5 de 9 pines)
(consulte la pág.1, N.º 24)
(USB6)
(consulte la pág.1, N.º 9)
SATA3_0_1SATA3_4_5SATA3_2_3
Conecte el indicador LED
de alimentación del chasis
a este cabezal para
indicar
el estado de alimentación
del sistema.
Estos seis conectores
SATA3 son compatibles
con cables de datos SATA
para dispositivos de
almacenamiento interno
con una velocidad de
transferencia de datos de
hasta 6,0 Gb/s.
Además de dos puertos
USB 2.0 en el panel de E/S,
esta placa base cuenta con
dos bases de conexiones y
un puerto. Cada cabezal
USB 2.0 admite dos
puertos.
Español
Cabezales USB 3.0
(USB3_6_7 de 19 pines)
(consulte la pág.11, N.º 10)
Vbus
IntA_PA_SSRX-
IntA_PA_SSRX+
GND
IntA_PA_SSTX-
IntA_PA_SSTX+
GND
IntA_PA_D-
IntA_PA_D+
VbusVbus
IntA_PB_SSRX-
IntA_PB_SSRX+
GND
IntA_PB_SSTX-
IntA_PB_SSTX+
GND
IntA_PB_D-
IntA_PB_D+
Dummy
Además de seis puertos
USB 3.0 en el panel de E/S,
esta placa base cuenta con
una base de conexiones.
Cada cabezal USB 3.0
admite dos puertos.
77
77
Page 80
Cabezal de audio del panel
J_SENSE
OUT2_L
1
MIC_RET
PRESENCE#
GND
OUT2_R
MIC2_R
MIC2_L
OUT_RET
1
SPEAKER
GND
OL
frontal
(HD_AUDIO1 de 9 pines)
(consulte la pág.1, N.º 29)
1. El Audio de Alta Denición (HDA, en inglés) es compatible con el método de sensor de
conectores, sin embargo, el cable del panel del chasis deberá ser compatible con HDA para
que pueda funcionar correctamente. Siga las instrucciones que se indican en nuestro manual
y en el manual del chasis para instalar su sistema.
2. Si utiliza un panel de audio AC’97, colóquelo en el cabezal de audio del panel frontal
siguiendo los pasos que se describen a continuación:
A. Conecte Mic_IN (MIC) a MIC2_L.
B. Conecte Audio_R (RIN) a OUT2_R y Audio_L (LIN) a OUT2_L.
C. Conecte Ground (Conexión a tierra) (GND) a Ground (GND).
D. MIC_RET y OUT_RET se utilizan únicamente con el panel de audio HD. No es necesario
que los conecte en el panel de audio AC’97.
E. Para activar el micrófono frontal, vaya a la cha “micrófono frontal” (FrontMic) en el
panel de control de Realtek y ajuste el “Volumen de grabación” (Recording Volume).
Este cabezal se utiliza para
conectar dispositivos de
audio al panel de audio
frontal.
Español
78
Cabezal de altavoces del
chasis
(SPEAKER1 de 4 pines)
(consulte la pág.1, N.º 15)
Conectores del ventilador
de alimentación y del
chasis
(CHA_FAN1 de 4 pines)
(consulte la pág.1, N.º 27)
(CHA_FAN2 de 3 pines)
(consulte la pág.1, N.º 26)
(CHA_FAN3 de 3 pines)
(consulte la pág.1, N.º 11)
(PWR_FAN1 de 3 pines)
(consulte la pág.1, N.º 30)
DUMMY
+5V
+12V
CHA_FAN_SPEED
FAN_SPEED_CONTR
DUMMY
Conecte el altavoz del
chasis a este cabezal.
Conecte los cables del
ventilador a los conectores
del ventilador y haga
coincidir el cable negro
con el pin de conexión a
tierra.
Page 81
Z87M OC Formula
CPU_FAN_SPEED
N_SPEED
FA
4
8
1
RRI#1
DUMMY
1
Conectores del ventilador
de la CPU
(CPU_FAN1 de 4 pines)
(consulte la pág.1, N.º 3)
(CPU_FAN2 de 3 pines)
(consulte la pág.1, N.º 2)
Conector de alimentación
ATX
(ATXPWR1 de 24 pines)
(consulte la pág.1, N.º 8)
Conector de alimentación
ATX de 12V
(ATX12V1 de 8 pines)
(consulte la pág.1, N.º 1)
Cabezal de módulo
infrarrojo
(IR1 de 5 pines)
(consulte la pág.1, N.º 28)
4 3 2 1
+12V
+12V
GND
IRTX
IRRX
CPU_FA
+5VSB
GND
N_SPEED_CONTROL
GN D
5
1
Esta placa base contiene
un conector de ventilador
(ventilador silencioso) de
CPU de 4 pines. Si tiene
pensando conectar un
ventilador de CPU de 3
pines, conéctelo al Pin 1-3.
Esta placa base contiene un
conector de alimentación
ATX de 24 pines. Para
utilizar una toma de
alimentación ATX de 20
pines, conéctela en los
Pines del 1 al 13.
Esta placa base contiene un
conector de alimentación
ATX de 12V y 8 pines.
Para utilizar una toma
de alimentación ATX de
4 pines, conéctela en los
Pines del 1 al 5.
Español
Este cabezal admite un módulo
infrarrojo opcional de transmisión
y recepción inalámbrico.
Cabezal de puerto serie
(COM1 de 9 pines)
(consulte la pág.1, N.º 25)
RRXD1
DDTR#1
TTXD1
DDCD#1
DDSR#1
CCTS#1
RRTS#1
GND
Este cabezal COM1 admite
un módulo de puerto serie.
79
79
Page 82
1.5 Interruptores inteligentes
AB
La placa base contiene tres interruptores inteligentes: Botón de alimentación,
interruptor de reseteo e interruptor de borrado de CMOS; que permiten a los usuarios
encender y apagar rápidamente el sistema, resetearlo o borrar los valores de CMOS.
Español
Interruptor de alimentación
(PWRBTN)
(consulte la pág.1, N.º 18)
Interruptor de reseteo
(RSTBTN)
(consulte la pág.1, N.º 19)
Botón Borrar la memoria
CMOS
(CLRCBTN)
(consulte la pág.1, N.º 20)
Esta función podrá utilizarla únicamente cuando apague su ordenador y desconecte la
corriente.
Interruptor del Modo
Lento(SLOWMODE1)
(consulte la pág.1, N.º 6)
Interruptor de selección
del BIOS(BIOS_SEL1)
(consulte la pág.1, N.º 21)
Power
Reset
OFF
ON
El interruptor de
alimentación permite a
los usuarios encender y
apagar rápidamente el
sistema.
El interruptor de reseteo
permite a los usuarios
resetear rápidamente el
sistema.
El botón Borrar la
memoria CMOS permite
a los usuarios borrar
rápidamente los valores de
la memoria CMOS.
Si el Modo Lento está
activado, el procesador
funciona con la frecuencia
más baja.
El interruptor de selección
del BIOS permite arrancar
el sistema desde el BIOS A
o el BIOS B.
80
Esta placa base contiene dos chips de BIOS, un BIOS principal (BIOS_A) y un BIOS de copia de
seguridad (BIOS_B), que aumentan la seguridad y la estabilidad de su sistema. Normalmente,
el sistema funcionará con el BIOS principal. Sin embargo, si el BIOS principal está dañado de
alguna forma, deberá simplemente cambiar el interruptor de selección del BIOS a la posición “B”.
De esta forma, el sistema arrancará desde el BIOS de copia de seguridad la próxima vez que lo
inicie. Después, utilice “Secure Backup UEFI” (copia de seguridad segura de UEFI) en “UEFI
Setup Utility” (herramienta de conguración de UEFI) para duplicar una copia de trabajo de
los archivos del BIOS en el BIOS principal con el objetivo de garantizar que el sistema funcione
correctamente. Por cuestiones de seguridad, los usuarios no pueden actualizar el BIOS de copia
de seguridad manualmente. Los usuarios deberán consultar los indicadores LED del BIOS
(BIOS_A_LED o BIOS_B_LED) para identicar qué BIOS está activado en ese momento.
Page 83
Interruptor del Modo LN2
(LN2MODE1)
(consulte la pág.1, N.º 7)
OFF
ON
Z87M OC Formula
El modo LN2 ayuda a
eliminar los problemas de
errores del arranque en frío
de los procesadores durante
el overclocking extremo con
nitrógeno líquido.
81
81
Español
Page 84
Русский
1 Введение
Благодарим вас за приобретение надежной материнской платы ASRock
Z87M OC Formula, выпускаемой под постоянным строгим контролем
компании ASRock. Эта материнская плата обеспечивает великолепную
производительность и характеризуется прочной конструкцией в соответствии с
требованиями компании ASRock в отношении качества и долговечности.
По причине обновления спецификации на материнскую платформу и программного
обеспечения BIOS содержимое настоящей документации может быть изменено без
предварительного уведомления. При изменении содержимого настоящего документа
его обновленная версия будет доступна на веб-сайте ASRock без предварительного
уведомления. При необходимости технической поддержки, связанной с материнской
платой, посетите веб-сайт и найдите на нем информацию о модели используемой
вами материнской платы. На веб-сайте ASRock также можно найти самый последний
перечень поддерживаемых VGA-карт и ЦП. Веб-сайт ASRock http://www.asrock.com.
1.1 Комплект поставки
• Материнская плата ASRock Z87M OC Formula (форм-фактор Micro ATX)
• Краткое руководство по установке ASRock Z87M OC Formula
• Диск с ПО для ASRock Z87M OC Formula
• 4 х кабеля передачи данных Serial ATA (SATA) (приобретаются отдельно)
• 10 х стоек ОС
• Термопаста GELID Solution GC-Extreme
• 1 х винт модуля WiFi
• 1 х винт mSATA
82
Page 85
1.2 Спецификация
Z87M OC Formula
Платформа
A-Style
Комплект OC
Formula
• Форм-фактор Micro ATX
• Конструкция Premium Gold Capacitor (с использованием
высококачественных конденсаторов из проводящих
полимеров 100% производства Японии)
• Home Cloud
• Purity Sound
• Вход HDMI
Силовой комплект OC
• Система питания 12
• Digi Power
• Двухблочный полевой МОП-транзистор (DSM)
• Многократный конденсатор сглаживающего фильтра
(МКСФ) (фильтрация различных шумов 3 различными
конденсаторами: твердотельный конденсатор DIP, POSCAP
и MLCC)
• Дроссель из высококачественного сплава (снижает потери
в сердечнике на 70% по сравнению с сердечником из
железного порошка)
Соединительный комплект OC Formula
• Высокоплотный разъем питания (8-контактный)
• 15μGold Finger (гнезда под ЦП, гнезда под модули памяти
и PCIE x 16 гнезд)
• Гнездо, не вносящее искажений
Комплект охлаждения OC Formula
• 8-слойная печатная схема
• 4 x медная, 2 унции
• Термопаста GELID Solutions GC-Extreme
TM
Русский
ЦП
Чипсет
• Поддержка процессоров 4-го поколения Intel® CoreTM i7 /
i5 / i3 / Xeon® / Pentium® / Celeron® в исполнении LGA1150
• Поддержка технологии Intel® Turbo Boost 2.0
• Поддержка процессоров Intel® серии K с
разблокированным множителем
• Поддержка полного разгона процессора ASRock BCLK
• Intel® Z87
83
83
Page 86
Память
• Технология двухканальной памяти DDR3
• 4 х гнездо DDR3 DIMM
• Поддержка модулей памяти DDR3 3000+(OC)/2933(OC)/
• Поддержка Intel® Extreme Memory Prole (XMP)1.3/1.2
• Гнездо, не вносящее искажений
Русский
Гнезда
расширения
Графическая
система
• 2 x PCI Express 3.0 x16 гнезд (PCIE1/PCIE3:одинарный при
x16 (PCIE1); двойной при x8 (PCIE1) / x8 (PCIE3))
• 1 x гнездо PCI Express 2.0 x4
• 1 x PCI Express 2.0 x1
• 1 x гнездо half mini-PCI Express:
• 1 x гнездо mSATA/mini-PCI Express
*Гнездо mSATA/mini-PCI Express используется совместно с
гнездом SATA3_4.
• Поддержка AMD Quad CrossFireXTM и CrossFireXTM
• Поддержка NVIDIA® Quad SLITM и SLI
• Поддержка выходных сигналов Intel® HD Graphics Built-
in Visuals и VGA возможна только при использовании
процессоров со встроенными графическими
процессорами.
• Поддержка встроенных технологий визуализации Intel®
HD Graphics: Intel® Quick Sync Video с AVC, MVC (S3D) и
MPEG-2 Full HW Encode1, Intel® InTruTM 3D, Intel® Clear
Video HD Technology, Intel® InsiderTM, Intel® HD Graphics
4400/4600
• Pixel Shader 5.0, DirectX 11.1
• Максимальный объем совместно используемой памяти:
1792 Мб
• Два выхода VGA:поддержка портов HDMI и DisplayPort
независимыми контроллерами дисплея
• Поддержка технологии HDMI с максимальным
разрешением до 4K × 2K (4096x2304) при 24 Гц
• Поддержка DisplayPort с максимальным разрешением до
4K × 2K (4096x2304) при 24 Гц
• Поддержка Auto Lip Sync, Deep Color (12bpc), xvYCC и
HBR (High Bit Rate Audio) по HDMI (необходим HDMIсовместимый монитор)
• Поддержка функции HDCP через порты HDMI и
DisplayPort
• Поддержка воспроизведения Full HD 1080p Blu-ray (BD)
через порты HDMI и DisplayPort
TM
84
Page 87
Z87M OC Formula
Аудио
ЛВС
Порты вводавывода
на задней
панели
• 7.1-канальный звук высокой четкости HD Audio с защитой
данных (аудиокодек Realtek ALC1150)
• Поддержка Premium Blu-ray Audio
• Поддержка Purity Sound™
- 115 дБ SNR DAC с дифференциальным усилителем
- TI® NE5532 Premium Headset Amplier (поддержка
наушников с сопротивлением до 600 Ом)
- Технология Direct Drive
- Крышка с экранированием от электромагнитных помех
- Изолирующее экранирование печатной платы
• Поддержка DTS-подключения
• Gigabit LAN 10/100/1000 Мб/с
• Giga PHY Intel® I217V
• Поддержка технологии Intel® Remote Wake Technology
• Поддержка Wake-On-LAN
• Поддержка Energy Ecient Ethernet 802.3az
• Поддержка PXE
• 1 x PS/2 для мыши/клавиатуры
• 1 x HDMI-выход
• 1 x HDMI-вход
• 1 x DisplayPort
• 1 x оптический выходной SPDIF
• 1 x eSATA
• 2 x USB 2.0
• 4 x портов USB 3.0 (Intel® Z87) (концентратор ASMedia)
• 2 x порты USB 3.0 (Intel® Z87)
• 1 x RJ-45 для ЛВС с СИД (СИД ACT/LINK и МИД SPEED)
• 1 x кнопка сброса настроек CMOS
• Разъемы HD Audio: задние динамики / центральный
• 6 x разъем SATA3 6,0 Гб/с, поддержка RAID (RAID 0, RAID
1, RAID 5, RAID 10, Intel Rapid Storage Technology 12 и
Intel Smart Response Technology), NCQ, AHCI и «горячая»
замена
• 1 x разъем eSATA, поддержка RAID (RAID 0, RAID 1, RAID
5, RAID 10, Intel Rapid Storage Technology 12 и Intel Smart
Response Technology), функции NCQ, AHCI и «горячая»
замена
*разъем eSATA используется совместно с портом SATA3_1.
Русский
Разъемы
Особенности
BIOS
• 1 x колодка IR
• 1 x колодка СОМ-порта
• 1 x колодка светодиодного индикатора питания
• 2 x разъем для вентилятора ЦП (1 х 4-контактный, 1 х
3-контактный)
• 3 x разъема для вентилятора корпуса (1 х 4-контактный, 2
х 3-контактный)
• 1 x разъем для вентилятора блока питания (3-контактный)
• 1 х разъем питания АТХ (24-контактный)
• 8-контактные разъемы питания 12 В - 1 шт.
(Высокоплотный разъем питания)
• 1 x аудиоразъем на передней панели
• 2 x колодки USB 2.0 (поддержка 4 портов USB 2.0)
• 1 х вертикальный разъем USB 2.0 типа A
• 1 x колодка USB 3.0 (поддержка 2 портов USB 3.0)
• 1 x кнопка питания с СИД
• 1 x кнопка перезагрузки с СИД
• 1 x кнопка сброса настроек CMOS
• 1 x Post Status Checker (PSC)
• 1 x переключатель медленного режима работы
• 1 x переключатель режима LN2
• 1 x селекторный переключатель BIOS
• 2 x 64 Мб AMI UEFI Legal BIOS с поддержкой
многоязычного ГИП (1 x основной BIOS и 1 x BIOS
резервного копирования)
• Поддержка технологии безопасного резервного
копирования UEFI
• Совместимость с управлением энергопотреблением по
ACPI 1.1
• Совместимость с ErP/EuP (необходим блок питания,
соответствующий стандарту ErP/EuP)
* Для получения дополнительной информации об изделии посетите наш веб-сайт:
http://www.asrock.com
Следует учитывать, что разгон процессора, включая изменение настроек BIOS,
применение технологии Untied Overclocking Technology и использование инструментов
разгона независимых производителей, сопряжен с определенным риском. Разгон
процессора может повлиять на стабильность системы или даже привести к
повреждению ее компонентов и устройств. Вы выполняете разгон процессора на ваш
собственный риск и за свой счет. Мы не несем ответственность за возможный ущерб,
вызванный разгоном процессора.
Русский
В связи с ограничением при работе под 32-разрядной ОС Windows® фактический
объем памяти может быть меньше 4 Гбайт. Для 64-разрядных ОС Windows® таких
ограничений нет. Для использования той памяти, которую ОС Windows® не может
использовать, используйте ASRock XFast RAM.
87
87
Page 90
Русский
1.3 Установка перемычек
Установка перемычек показана на рисунке. При установке колпачковой
перемычки на контакты перемычка «замкнута». Если колпачковая перемычка
на контакты не установлена, перемычка «разомкнута». На рисунке показана
3-контактная перемычка с замкнутыми контактами 1 и 2 при установке на них
колпачковой перемычки.
Перемычка сброса
настроек CMOS
(CLRCMOS1)
(См. стр. 1, № 22)
CLRCMOS1 используется для удаления данных CMOS. Чтобы сбросить
и обнулить параметры системы на настройки по умолчанию, выключите
компьютер и извлеките отключите кабель питания от источника питания.
Подождите 15 секунд и перемычкой замкните контакты 2 и 3 на CLRCMOS1
на 5 секунд. Не сбрасывайте настройки CMOS сразу после обновления BIOS.
При необходимости сбросить настройки CMOS сразу после обновления BIOS
сначала перезагрузите систему, а затем выключите компьютер перед сбросом
настроек CMOS. Учтите, что пароль, дата, время и профиль пользователя по
умолчанию сбрасываются только в том случае, если извлечь батарею CMOS.
1.4 Колодки и разъемы, расположенные на материнской
плате
Расположенные на материнской плате колодки и разъемы перемычками НЕ являются.
НЕ устанавливайте на эти колодки и разъемы колпачковые перемычки. Установка
колпачковых перемычек на эти колодки и разъемы может вызвать неустранимое
повреждение материнской платы.
Колодка системной
панели
(9-контактная, PANEL1)
(См. стр. 1, № 17)
PWRBTN (кнопка питания):
Подключение кнопки питания, расположенной на передней панели корпуса. Можно
настроить порядок выключения системы с использованием кнопки питания.
RESET (кнопка перезагрузки):
Подключение кнопки перезагрузки системы, расположенной на передней панели
корпуса. Нажмите кнопку перезагрузки, чтобы перезапустить компьютер, если он
завис и нормальный запуск невозможен.
PLED (светодиодный индикатор питания системы):
Подключение индикатора состояния, расположенного на передней панели корпуса.
Светодиодный индикатор горит, когда система работает. Когда система находится
в режиме ожидания S1/S3, светодиод мигает. Когда система находится в режиме
ожидания S4 или выключена (S5), светодиод не горит.
HDLED (светодиодный индикатор работы жесткого диска):
Подключение светодиодного индикатора работы жесткого диска, расположенного на
передней панели. Светодиодный индикатор горит, когда жесткий диск выполняет
считывание или запись данных.
Передняя панель может быть разной на разных корпусах. В основном передняя панель
включает в себя кнопку питания, кнопку перезагрузки, светодиодный индикатор
питания, светодиодный индикатор работы жесткого диска, динамик и т. д. При
подключении передней панели к этой колодке правильно подключайте провода к
контактам.
1
PLED+
PLED-
HDLED-
HDLED+
PWRBTN#
GND
RESET#
GND
GND
Подключите
расположенные на
корпусе выключатель
питания, кнопку
перезагрузки и
индикатор состояния
системы к этой колодке
в соответствии с
распределением
контактов,
приведенным ниже.
Перед подключением
кабелей определите
положительный
и отрицательный
контакты.
Русский
89
89
Page 92
Колодка светодиодного
1
PLED+
PLED+
PLED-
DUMMY
GND
GND
P+
P-
USB_PWR
P+
P-
USB_PWR
1
1
индикатора питания
(3-контактная, PLED1)
(См. стр. 12, № 16)
Подключите
светодиодный индикатор
питания корпуса к
этой колодке,
чтобы
обеспечить индикацию
состояния питания
системы.
Русский
Разъемы Serial ATA3
(SATA3_0_1:
см. стр.1, № 12)
(SATA1_2_3:
См. стр. 1, № 13)
(SATA3_4_5:
См. стр. 1, № 14)
Колодки USB 2.0.
(9-контактная, USB2_3)
(См. стр. 1, № 23)
(9-контактная, USB4_5)
(См. стр. 1, № 24)
(USB6)
(См. стр. 1, № 9)
Эти шесть
разъемов SATA3
предназначены для
подключения кабелей
SATA внутренних
запоминающих
устройств для передачи
данных со скоростью до
6,0 Гб/с.
SATA3_0_1SATA3_4_5SATA3_2_3
Кроме двух портов USB
2.0, на панели вводавывода на материнской
плате также есть две
колодки и один порт.
Каждая колодка USB 2.0
может поддерживать два
порта.
90
Колодки USB 3.0.
(19-контактная,USB3_6_7)
(См. стр. 11, № 10)
Vbus
IntA_PA_SSRX-
IntA_PA_SSRX+
IntA_PA_SSTX-
IntA_PA_SSTX+
IntA_PA_D-
IntA_PA_D+
VbusVbus
IntA_PB_SSRX-
IntA_PB_SSRX+
GND
IntA_PB_SSTX-
GND
IntA_PB_SSTX+
GND
IntA_PB_D-
GND
IntA_PB_D+
Dummy
Кроме шести портов USB
3.0, на панели вводавывода на материнской
плате также есть
одна колодка. Каждая
колодка USB 3.0 может
поддерживать два порта.
1. Аудиосистема высокого разрешения поддерживает функцию распознавания разъема,
но для е правильной работы необходимо, чтобы провод панели корпуса поддерживал
передачу сигналов HDA. Инструкции по установке системы см. в этом руководстве
и руководстве на корпус.
2. При использовании аудиопанели AC’97 подключите ее к аудиоколодке передней
панели, как указано далее:
A. Подключите Mic_IN (MIC) к MIC2_L.
B. Подключите Audio_R (RIN) к OUT2_R, Audio_L (LIN) к OUT2_L.
C. Подключите провод заземления (GND) к контакту заземления (GND).
D. Контакты MIC_RET и OUT_RET используются только для аудиопанели высокого
разрешения. При использовании аудиопанели AC’97 их подключать не нужно.
E. Чтобы активировать передний микрофон, перейдите на вкладку FrontMic панели
управления Realtek и отрегулируйте параметр Recording Volume (Громкость записи).
Колодка динамика
корпуса
+5V
(4-контактная,
DUMMY
SPEAKER1)
Эта колодка
предназначена
для подключения
аудиоустройств к
передней аудиопанели.
Предназначена для
подключения динамика
корпуса.
(См. стр. 1, № 15)
Разъемы для
вентиляторов корпуса и
блока питания
(4-контактный, CHA_
FAN1)
(См. стр. 1, № 27)
(3-контактный, CHA_
FAN2)
(См. стр. 1, № 26)
(3-контактный, CHA_
FAN3)
(См. стр. 1, № 11)
(3-контактный, PWR_
FAN1)
(См. стр. 1, № 30)
+12V
CHA_FAN_SPEED
FAN_SPEED_CONTR
Предназначены для
подключения кабелей
разъемов вентиляторов
и подключения черного
провода к заземлению.
91
91
Русский
Page 94
Разъемы вентиляторов
CPU_FAN_SPEED
N_SPEED
FA
4 1
8 5
RRI#1
1
ЦП
(4-контактный, CPU_
FAN1)
(См. стр. 1, № 3)
(3-контактный, CPU_
FAN2)
(См. стр. 1, № 2)
4 3 2 1
+12V
N_SPEED_CONTROL
CPU_FA
GND
+12V
GN D
Эта материнская
плата снабжена
4-контактным разъемом
для малошумящего
вентилятора ЦП. Если вы
собираетесь подключить
3-контактный
вентилятор охлаждения
процессора, подключайте
его к контактам 1-3.
Русский
Разъем питания АТХ
(24-контактный,
ATXPWR1)
(См. стр. 1, № 8)
Разъем питания АТХ 12 В
(8-контактный,
ATX12V1)
(См. стр. 1, № 1)
Колодка инфракрасного
модуля
(5-контактная, IR1)
(См. стр. 1, № 28)
Колодка
последовательного порта
(9-контактная, COM1)
(См. стр. 1, № 25)
1
IRTX
IRRX
RRXD1
DDTR#1
TTXD1
DDCD#1
+5VSB
GND
DDSR#1
GND
DUMMY
CCTS#1
RRTS#1
Эта материнская плата
снабжена 24-контактным
разъемом питания АТХ.
Чтобы использовать
20-контактный
разъем питания ATX,
подключите его вдоль
контакта 1 и контакта 13.
Эта материнская плата
снабжена 8-контактным
разъемом питания АТХ
12 В. Чтобы использовать
4-контактный
разъем питания ATX,
подключите его вдоль
контакта 1 и контакта 5.
Эта колодка поддерживает
дополнительную беспроводную
передачу и прием сигналов
инфракрасного модуля.
Колодка COM1
поддерживает
подключение модуля
последовательного
порта.
92
Page 95
Z87M OC Formula
AB
1.5 Электронные кнопки
Материнская плата снабжена тремя электронными кнопками: Кнопка питания,
кнопка перезагрузки и кнопка сброса настроек CMOS предназначены для
быстрого включения/выключения системы, перезагрузки системы и обнуления
значений CMOS.
Кнопка питания
(PWRBTN)
(См. стр. 1, № 18)
Кнопка перезагрузки
(RSTBTN)
(См. стр. 1, № 19)
Кнопка сброса настроек
CMOS
(CLRCBTN)
(См. стр. 1, № 20)
Эта функция работает только, если питания компьютера выключено и он отключен
от сети питания.
Переключатель
медленного режима
работы(SLOWMODE1)
(См. стр. 1, № 6)
Селекторный
переключатель
BIOS(BIOS_SEL1)
(См. стр. 1, № 21)
Power
Reset
OFF
ON
Кнопка питания
предназначена для
быстрого включения/
выключения системы.
Кнопка перезагрузки
предназначена для
быстрой перезагрузки
системы.
Кнопка сброса настроек
CMOS предназначена
для быстрого обнуления
значений CMOS.
Если включен
медленный режим
работы, процессор
работает на самой
низкой частоте.
Селекторный
переключатель BIOS
предназначен для
запуска системы с
использованием BIOS A
или BIOS B.
Русский
Эта материнская плата снабжена двумя микросхемами BIOS — основной BIOS
(BIOS_A) и BIOS резервного копирования (BIOS_B), — что повышает уровень
защиты и стабильности системы. Обычно система использует основную BIOS. При
повреждении или сбое основной BIOS просто установите селекторный переключатель
BIOS в положение «В», и при следующем запуске системы будет использоваться
резервная BIOS. После этого в утилите настройки UEFI используйте опцию Secure
Backup UEFI, чтобы выполнить копирование рабочих файлов BIOS в основную BIOS
для обеспечения нормальной работы системы. Для обеспечения безопасности ручное
обновление резервной копии BIOS пользователем отключено. Определить, какая BIOS
используется в настоящее время, можно по светодиодном индикаторам BIOS (BIOS_
A_LED или BIOS_B_LED).
93
93
Page 96
Русский
Переключатель режима
LN2
(LN2MODE1)
(См. стр. 1, № 7)
OFF
ON
Режим LN2 используется
для устранения сбоев
экстремально разогнанного
процессора с охлаждением
жидким азотом при
"холодной" начальной
загрузке.
94
Page 97
Z87M OC Formula
1 Introdução
Obrigado por ter comprado a placa principal ASRock Z87M OC Formula, esta placa
principal foi fabricada pela ASRock e sujeita a um rigoroso controlo de qualidade.
Esta placa principal oferece um excelente desempenho com um design robusto em
conformidade com o compromisso da ASRock em fabricar produtos de qualidade e
resistentes.
Dado que as especicações da placa principal e o soware do BIOS poderão ser actualizados,
o conteúdo desta documentação estará sujeito a alterações sem aviso prévio. Caso ocorram
modicações a esta documentação, a versão actualizada estará disponível no Web site da
ASRock sem aviso prévio. Se necessitar de assistência técnica relacionada com esta placa
principal, visite o nosso Web site para obter informações especícas acerca do modelo que está
a utilizar. Também poderá encontrar a lista de placas VGA e CPU mais recentes suportadas no
Web site da ASRock. Web site da ASRock http://www.asrock.com.
1.1 Conteúdo da embalagem
• Placa principal ASRock Z87M OC Formula (factor de forma Micro ATX)
• Guia de instalação rápida da placa principal ASRock Z87M OC Formula
• CD de suporte da placa principal ASRock Z87M OC Formula
• 4 x Cabos de dados Serial ATA (SATA) (Opcional)
• 10 x Bases OC
• Composto térmico GELID Solution GC-Extreme
• 1 parafuso para módulo WiFi
• 1 parafuso mSATA
Português
95
95
Page 98
1.2 Especicações
Português
Plataforma
Estilo A
Kit para placa
principal OC
Formula
• Formato Micro ATX
• Design de condensadores banhados a ouro de alta qualidade
(Condensadores de polímeros condutores de alta qualidade
100% fabricados no Japão)
• Home Cloud
• Purity Sound
• Entrada HDMI
Kit de alimentação OC Formula
• Design com 12 fases de alimentação
• Digi Power
• Dual-Stack MOSFET (DSM)
• Filtro Múltiplo (MFC) (Filtra diferentes ruídos através de
3 condensadores diferentes: Tampa DIP sólida, POSCAP e
MLCC)
• Indutor de liga metálica premium (Reduz as perdas de núcleo
em 70% comparado com indutor de pó de ferro)
Kit de ligação OC Formula
• Conector de alimentação de alta densidade (8 pinos)
• Contactos banhados a ouro de 15μ (Sockets de CPU, sockets de