Askey Computer WLU5540B NB User Manual

ENGLISH

THE FOLLOWING APPLIES IN THE U.S.A. AND CANADA
This device complies with Part 15 of FCC Rules and RSS-Gen of IC Rules.

Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept

any interference received, including interference that may cause undesired operation
of this device.

This transmitter must not be co-located or operated in conjunction with any other
antenna or transmitter.

This product is restricted to indoor use due to its operation in the 5.15 to 5.25
GHz frequency range.

FCC and IC require this product to be used indoors for the frequency range 5.15 to

5.25 GHz to reduce the potential for harmful interference to co-channel Mobile

Satellite systems. High power radars are allocated as primary users of the 5.25 to

5.35 GHz and 5.65 to 5.85 GHz bands. These radar stations can cause interference with

and/or damage this product.
The available scientific evidence does not show that any health problems are

associated with using low power wireless devices.
There is no proof, however, that these low power wireless devices are absolutely safe.

Low power Wireless devices emit low levels of radio frequency energy (RF) in the
microwave range while being used.

Whereas high levels of RF can produce health effects (by heating tissue), exposure
to low-level RF that does not produce heating effects causes no known adverse health

effects.
Many studies of low-level RF exposures have not found any biological effects. Some

studies have suggested that some biological effects might occur, but such findings
have not been confirmed by additional research.

Wireless LAN adaptor has been tested and found to comply with FCC/IC radiation exposure
limits set forth for an uncontrolled equipment and meets the FCC radio frequency (RF)

Exposure Guidelines in Supplement C to OET65 and RSS-102 of the IC radio frequency
(RF) Exposure rules.

THE FOLLOWING APPLIES ONLY IN THE U.S.A.

Federal Communication Commission Interference Statement:

This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmfulinterference to radiocommunications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the userisencouraged to try to correct the interferenceby one or more
of the following measures:

 Reorient or relocate the receiving antenna.
 Increase the separation between the equipment and receiver.
 Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

 Consult the dealer or an experienced host product technician for help.

This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received, including interference
that may cause undesired operation.

This device is restricted to indoor use when operated in the 5.15 to 5.25 GHzfrequency range.

THE FOLLOWING APPLIES ONLY IN CANADA.

This Class B digital apparatus complies with Canadian ICES-003.
Product Identification Marking is located on the top of the Wireless Module.

Federal Communication Commission (FCC) /IC Radiation Exposure Statement

This EUT is compliance with SAR for general population/uncontrolled exposure limits in
ANSI/IEEE C95.1-1999/ IC RSS-102 and had been tested in accordance with the measurement
methods and procedures specified in OET Bulletin 65 Supplement C/ IEEE 1528. This
equipment should be installed and operated with minimum distance 0.5cm between the radiator
& your body.

This Class [B] digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe [B] est conforme à la norme NMB-003 duCanada.

End Product Labeling:

The final end product must be labeled in a visible area with the following: “Contains
FCC ID: H8N-WLU5540B-NB”

This device is intended only for OEM integrators under the following conditions:

1) The antenna must be installed such that 20 cm is maintained between the antenna
and users, and 2) The transmitter module may not be co-located with any other

transmitter or antenna. As long as 2 conditions above are met, further transmitter test
will not be required. However, the OEM integrator is still responsible for testing their

end-product for any additional compliance requirements required with this module
installed.

Manual Information to the End User

The OEM integrator has to be aware not to provide information to the end user
regarding how to install or remove this RF module in the user’s manual of the end

product which integrates this module. The end user manual shall include all required
regulatory information/warning as show in this manual.