Askey Computer RTA300WD73 User Manual

RTA300W-D73 ADSL Router

User’s Manual

Rev:01

2003/1/22

No part of this publication may be reproduced in any form by any means without the prior written permission. Other trademarks or brand names mentioned herein are trademarks or registered trademarks of their respective companies.

2003/1/22

Rev:01

000300w-rta-73

ADSL Router User Manual

Safety Notes

For Installation

 Use only the type of power source indicated on the marking labels.  Use only the power adapter supplied with the product.  Do not overload wall outlet or extension cords as this may increase the risk of electric shock or file. If the

power cord is frayed, replace it with a new one.

 Proper ventilation is necessary to prevent the product overheating. Do not block or cover the slots and

openings on the device, which are intended for ventilation and proper operation. It is recommended to mount the product with a stack.

 Do not place the product near any source of heat or expose it to direct sunshine.  Do not expose the product to moisture. Never spill any liquid on the product.  Do not attempt to connect with any computer accessory or electronic product without instructions from

qualified service personnel. This may result in risk of electronic shock or file.

 Do not place this product on an unstable stand or table.

For Using

 Power off and unplug this product from the wall outlet when it is not in use or before cleaning. Pay

attention to the temperature of the power adapter. The temperature might be high.

 After powering off the product, power on the product at least 15 seconds later.  Do not block the ventilating openings of this product.  When the product is expected to be not in use for a period of time, unplug the power cord of the product to

prevent it from the damage of storm or sudden increases in rating.

For Service

Do not attempt to disassemble or open covers of this unit by yourself. Nor should you attempt to service the product yourself, which may void the user’s authority to operate it. Contact qualified service personnel under the following conditions:

 If the power cord or plug is damaged or frayed.  If liquid has been spilled into the product.  If the product has been exposed to rain or water.  If the product does not operate normally when the operating instructions are followed.  If the product has been dropped or the cabinet has been damaged.  If the product exhibits a distinct change in performance.

Warning

 This equipment must be installed and operated in accordance with provided instructions and a minimum 20

cm spacing must be provided between computer mounted antenna and person’s body (excluding extremities of hands, wrist and feet) during wireless modes of operation.

 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

 FCC RF Radiation Exposure Statement: The equipment complies with FCC RF radiation exposure limits

set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body.

Caution

 Any changes or modifications not expressly approved by the party responsible for compliance could void

the authority to operate equipment.

 This Transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

iii

Contents

Before You Use ..................................................................................................vi

Features ................................................................................................ vi

System Requirements ............................................................................. vii

Unpacking ............................................................................................ viii

Subscription for ADSL Service ................................................................. viii

Chapter 1: Overview .......................................................................................... 1

Physical Outlook.......................................................................................1

Front Panel ....................................................................................1

Rear Panel .....................................................................................2

Chapter 2: Installation....................................................................................... 3

Choosing a place for the ADSL Router .........................................................3

Connecting the ADSL Router ......................................................................3

USB Driver Installation..............................................................................4

For Windows 98 ..............................................................................4

For Windows ME .............................................................................6

For Windows 2000...........................................................................8

For Windows XP ............................................................................ 10

Uninstall the USB Driver.......................................................................... 12

For Windows 98 ............................................................................ 12

For Windows ME ...........................................................................12

For Windows 2000.........................................................................12

For Windows XP ............................................................................ 13

Chapter 3: Connection Mode ............................................................................ 15

Bridge Mode ..........................................................................................16

Router Mode.......................................................................................... 17

MER Mode ............................................................................................. 19

PPPoA + NAT Mode .................................................................................20

PPPoE + NAT Mode .................................................................................21

PPPoE Relay ..........................................................................................22

Multiple PVCs Mode ................................................................................23

Chapter 4: Configuration ................................................................................. 25

Setting TCP/IP on Client PC .....................................................................25

For Windows 98 ............................................................................ 25

For Windows NT............................................................................ 29

For Windows 2000.........................................................................32

For Windows ME ...........................................................................34

For Windows XP ............................................................................ 35

Configure PC to get IP address from DHCP................................................. 36

For Windows 98 ............................................................................ 36

For Windows NT............................................................................ 37

For Windows 2000.........................................................................37

For Windows ME ...........................................................................37

Contents

For Windows XP ............................................................................ 38

Renew IP Address on Client PC................................................................. 39

For Windows 98 ............................................................................ 39

For Windows NT............................................................................ 39

For Windows 2000.........................................................................40

For Windows ME ...........................................................................40

For Windows XP ............................................................................ 41

Chapter 5: Web Configuration.......................................................................... 43

Using Web-Based Manager ...................................................................... 43

Outline of Web Manager................................................................. 43

To Have the New Settings Take Effect .............................................. 44

Quick start ............................................................................................44

System .................................................................................................45

Device Information........................................................................45

Administrative Security .................................................................. 45

Quick Configuration .......................................................................46

Save Configuration........................................................................ 47

Upgrade Software ......................................................................... 47

Reset Router ................................................................................ 48

Status ..................................................................................................48

DSL Connection ............................................................................ 48

WAN Connection ...........................................................................49

Traffic Counter..............................................................................49

Routing Table ...............................................................................49

DHCP Table .................................................................................. 50

Wireless Client..............................................................................50

Configuration.........................................................................................51

DSL Configuration .........................................................................51

LAN Configuration .........................................................................51

WLAN Configuration ......................................................................54

WAN Configuration ........................................................................ 56

IP Route ...................................................................................... 58

DNS ............................................................................................ 59

Security....................................................................................... 61

Virtual Server ............................................................................... 65

UPnP (Optional) ............................................................................67

Chapter 6: Troubleshooting ............................................................................. 71

Problems with LAN .................................................................................71

Problems with WAN ................................................................................ 71

Problems with Upgrading......................................................................... 72

Chapter 7: Glossary ......................................................................................... 75

Appendix: Specifications.................................................................................. 77

Software...................................................................................... 77

Hardware..................................................................................... 78

Before You Use

BBeeffoorree YYoouu UUsse

Thank you for choosing the Asymmetric Digital Subscriber Line (ADSL) Router. With the asymmetric technology, this device runs over standard copper phone lines and provides a downstream rate at up to 8 Mbps and upstream rate at up to 1 Mbps. In addition, ADSL allows you to have both voice and data services in use simultaneously all over one phone line.

Equipped with Ethernet LAN interface, this ADSL Router can be connected to a LAN or a single Ethernet-equipped PC. A built-in dynamic host configuration protocol (DHCP) server automatically assigns IP addresses to PCs on the LAN, and with Network Address Translation (NAT) these PCs can communicate with the outside world with only one public IP. This ADSL Router provides an ideal Internet access solution for the corporate environment, the small office and the home user.

Features

ADSL Compliance

For Annex A ADSL Router

 ANSI T1.413 Issue 2

 ITU G.992.1 Annex A (G.dmt)

 ITU G.992.2 Annex A (G.lite)

 ITU G.994.1 (G.hs)

For Annex B ADSL Router

 ITU G.992.1 Annex B (G.dmt)

 ITU G.994.1 (G.hs)

ATM Features

 Compliant to ATM Forum UNI 3.1 / 4.0 Permanent Virtual Circuits (PVCs)

 Support up to 8 AAL5 Virtual Circuit Channels (VCCs) for UBR, CBR, VBR-rt, and VBR-nrt with traffic

shaping

 TR-037 Auto PVC

 RFC1483 (RFC2684) LLC Encapsulation and VC Multiplexing over AAL5

 RFC2364 Point-to-Point Protocol (PPP) over AAL5

 RFC2225 Classical IP and ARP over ATM

 RFC2516 PPP over Ethernet: support Relay (Transparent Forwarding) and Client functions

 OAM F4/F5 End-to-End/Segment Loopback Cells

Bridging Features

 Supports self-learning bridge specified in IEEE 802.1D Transparent Bridging

 Supports up to 4000 learning MAC addresses

(auto-provisioning)

 Transparent bridging among 10/100 Mb Ethernet and 802.11b LAN interfaces

Routing Features

 UPnP IGD

 NAT (Network Address Translation) / PAT (Port Address Translation) let multiple users on the LAN to access

the internet for the cost of only one IP address and enjoy various multimedia applications.

 ALGs (Application Level Gateways): such as NetMeeting, FTP, Quick Time, mIRC, Real Player, CuSeeMe, etc.

(Internet Gateway Device) with NAT traversal capability support

Before You Use

 Multiple Virtual Servers (e.g., Web, FTP, Mail servers) can be setup on user’s local network.

 Static routes, RFC1058 RIPv1, RFC1723 RIPv2.

 DNS Relay and DNS Server

 ARP Proxy

Security Features

 PAP (RFC1334), CHAP (RFC1994) for PPP session

 Firewall support IP packets filtering based on IP address/Port number/Protocol type and TCP code field flags

 Intrusion Detection provides protection from a number of attacks (such as SYN/FIN/RST Flood, Smurf,

WinNuke, Echo Scan, Xmas Tree Scan, etc)



WEP (Wired Equivalent Privacy) encryption uses RC4 with 64/128 bit key length (for wireless ADSL router only)

Wireless LAN Features

 Fully compatible to IEEE 802.11b standard and allow operating range up to 300 meters (open space) and 100

meters (indoor).

 The Direct Sequence Spread Spectrum (DSSS) technology is exploited.

 Seamless roaming within the 802.11 and 802.11b wireless LAN infrastructure

 Low power consumption via efficient power management

Configuration and Management

 User-friendly embedded web configuration interface with password protection

 Remote management accesses control

 Telnet session for local or remote management

 HTTP firmware upgrades via web browser GUI directly

 Distribute IP addresses to end users via DHCP server provided by ADSL router

 SNMPv1/v2c agent with MIB-II, PPP MIB, ADSL Line MIB.

Note: *1 This is optional. TR-037 Autopvc provisioning can be provided on demand. *2 This is optional. UPnP IGD and NAT Traversal function can be provided on demand. *3 This is optional. DNS server can be provided on demand.

System Requirements

For using this, you have to make sure you have the following that installed on the clients:

For Ethernet Clients

 Operating System must be Windows98/2000/NT/ME/XP

 10/100 Base-T NIC

 10/100 Base-T(UTP) network cable

 A Hub

For USB Clients

 Operating System must be Windows98/2000/NT/ME/XP

 USB cable

vii

ADSL Router User Manual

Unpacking

Check the contents of the package against the pack contents checklist below. If any of the items is missing, then contact the dealer from whom the equipment was purchased.

 ADSL Router

 Power Adapter and Cord

 RJ-11 ADSL Line Cable

 RJ-45 Ethernet Cable

 USB Cable

 Quick Start Guide

 Driver & Utility Software CD

Depending on the service type your vendor offers, you may be provide with the devices below:

 Splitter (for G.dmt version)

 Micro filter (for G.lite version)

Subscription for ADSL Service

To use the ADSL Router, you have to subscribe for ADSL service from your broadband service provider. According to the service type you subscribe, you will get various IP addresses:

Dynamic IP: If you apply for dial-up connection, you will be given an Internet account with username and

password. You will get a dynamic IP by dialing up to your ISP.

Static IP address: If you apply for full-time connectivity, you may get either one static IP address or a range of IP

addresses from your ISP. The number of IP addresses varies according to different ADSL service provider.

viii

Chapter 1: Overiew

CChhaapptteerr 11:: OOvveerrvviieew

Physical Outlook

FFrroonntt PPaanneel

The following illustration shows the front panel of the ADSL Router:

Front Panel for RTA300/RTA300B

Front Panel for RTA300UW/RTA300BUW

LED Indicators

The ADSL Router is equipped with LEDs on the front panel as described in the table below (from left to right):

LED Color Status Description

Unlit Power off.PWR Green

Solid Power on.

DIAG Green

LAN1 to LAN4

USB Green

WLAN Green

DSL Green

Green

Unlit Power off or initial self-test of the unit is OK.

Blinking

Solid Initial self-test failure or programming FLASH memory failure.

Unlit Power off or no Ethernet carrier is present.

Blinking Ethernet carrier is present and user data is going through Ethernet port.

Solid Ethernet carrier is present.

Unlit Power off or wait for USB connection going up.

Blinking User data is going through USB port.

Solid USB connection is OK.

Unlit Power off or no radio signal (WLAN card is not present or fails to function).

Blinking Traffic is going through Wireless LAN interface.

Solid Wireless LAN interface ready to work.

Unlit Power off or ADSL line connection is handshaking or training is in progress.

Blinking User data is going through ADSL port.

Solid ADSL line connection is OK.

When software downloading or updating operation parameters located in FLASH memory is in progress.

ADSL Router User Manual

RReeaarr PPaanneel

The following figure illustrates the rear panel of your ADSL Router.

DSL: RJ-11 connector

LAN: Ethernet RJ-45 connector

USB: USB Connector

Console: Console connector

: Power switch

12VDC: Power connector

Note: The Router incorporates a four-port switch for connection to your local Ethernet network. The Ethernet ports are marked LOCAL, and are capable of operation at either 10 Mbps (10 BASE-T) or 100 Mbps (100 BASE-Tx).

Chapter 2: Installation

CChhaapptteerr 22:: IInnssttaallllaattiioon

Choosing a place for the ADSL Router

1. Place the ADSL Router close to ADSL wall outlet and power outlet for the cable to reach it easily.

2. Avoid placing the device in places where people may walk on the cables. Also keep it away from direct

sunshine or heat sources.

3. Place the device on a flat and stable stand.

Connecting the ADSL Router

Follow the steps below to connect the related devices.

1. Remove the end of the phone line from your phone connector and plug it onto the “LINE” port of the POTS

Splitter. Use another phone line to connect your phone and splitter. Plug this phone line onto the “PHONE” port of the ADSL splitter, and plug the other end of the line onto your phone.

2. Use the line to connect the ADSL splitter (MODEM port) and router’s DSL port.

3. Please attach one end of the Ethernet cable with RJ-45 connector to the LAN port of your ADSL Router.

4. Connect the other end of the cable to the Ethernet port of the client PC.

5. If you want to connect to a hub for used by many devices, please connect the other end to the uplink port of the

hub.

ADSL Router User Manual

6. Connect the supplied power adapter to the PWR port of your ADSL Router, and plug the other end to a power

outlet.

7. Turn on the power switch.

Note:

For Full Rate (G.dmt) standard, a POTS Splitter is necessary on subscriber’s premise to keep the telephone and ADSL signals separated, giving them the capability to provide simultaneous Internet access and telephone service on the same line. To connect a POTS Splitter:

1. Connect the port Phone to your telephone.

2. Connect the port Modem to your ADSL Router.

3. Connect the port Line to the ADSL wall jack.

USB Driver Installation

If the ADSL Router is connected to a PC through USB interface, you will be prompted for the USB drivers when plugging the USB cable to the PC. Refer to the relevant operating system to install the USB drivers. Otherwise, you may skip this chapter.

FFoorr WWiinnddoowwss 998

Step 1 When plugging the USB cable to the PC, the system will automatically detect the USB ADSL Router.

When Add New Hardware Wizard window announces detecting of the USB device, click Next.

Note: If the USB device is not detected, check the USB cable between the PC and the device. Also verify that the device is power on.

Step 2 When prompted for driver files, select Search for the best driver… and click Next.

Chapter 2: Installation

Step 3 Insert the Installation CD into your CD-ROM drive. Select CD-ROM drive and click Next .

Step 4 When the system finds the driver, click Next.

Step 5 When Windows has finished installing the driver required, click Finish.

Step 6 After the USB driver installation, the system will automatically detect the USB ADSL Gateway. When Add

New Hardware Wizard window announces detecting of the USB device, click Next.

ADSL Router User Manual

Step 7 Repeat steps 2-4.

Step 8 Click Finish to complete the installation.

Step 9 When you are prompted with System Settings Change dialog box, click Yes to restart your computer.

FFoorr WWiinnddoowwss MME

Step 1 While plugging the USB cable to the PC, the system will automatically detect the USB ADSL Router.

When Add New Hardware Wizard window announces detecting of the USB device, select Specify the location of the driver (Advanced) and click Next.

Note: If the USB device is not detected, check the USB cable between the PC and the device. Also verify that the device is power on.

Step 2 Insert the Installation CD into your CD-ROM drive. Select the Search for the best drive for your device

option and then check the Removable Media box. Then click Next.

Step 3 While the system finds the driver, click Next.

Step 4 Click Finish to complete the installation.

Chapter 2: Installation

Step 5 After the USB driver installation, the system will automatically detect the USB ADSL Gateway. When

Found New Hardware Wizard window announces detecting of the USB device, choose specify the location of the driver(Advanced) item and click Next.

Step 6 Repeat steps 2-4.

Step 7 Click Finish to complete the installation.

Step 8 When you are prompted with System Settings Change dialog box, click Yes to restart your computer.

ADSL Router User Manual

FFoorr WWiinnddoowwss 2200000

Step 1 When plugging the USB cable to the PC, the system will automatically detect the USB ADSL Router.

When Found New Hardware Wizard window announces detecting of the USB device, click Next.

Note: If the USB device is not detected, check the USB cable between the PC and the device. Also verify that the device is powered on.

Step 2 Select Search for a suitable device… and click Next.

Step 3 When you are prompted for driver files, insert the Installation CD into your CD-ROM drive. Select CD-

ROM drives and click Next.

Step 4 Wilen the system finds the driver, click Next.

Step 5 Click Finish to complete the installation.

Chapter 2: Installation

Step 6 After USB driver installation, the system will automatically detect the USB ADSL Gateway. When Found

New Hardware Wizard window announces detecting of the USB device, click Next.

Step 7 Repeat steps 2-4. Step 8 A Digital Signature Not Found dialog box appears to ask you to continue the installation or stop the

procedure. Please click Yes. Then Windows XP copied the drivers from the Software Utility CD.

Step 9 Click Finish to complete the installation.

ADSL Router User Manual

FFoorr WWiinnddoowwss XXP

Step 1 When plugging the USB cable to the PC, the system will automatically detect the USB ADSL Router.

When Found New Hardware Wizard window announces detecting of the USB device, click Next.

Note: If the USB device is not detected, check the USB cable between the PC and the device. Also verify that the device is power on.

Step 2 The Windows will copy the drivers form the Software Utility CD.

Step 3 When the driver for USB Virtual Bus are copied onto your computer, click Finish for next step.

Chapter 2: Installation

Step 4 After USB driver installation, the system will automatically detect the USB ADSL Gateway. When Found

New Hardware Wizard window announces detecting of the USB device, click Next.

Step 5 Repeat steps 2-3.

Step 6 A Hardware Installation dialog box about digital signature appears to ask you to continue the installation or

stop the procedure. Please click Continue Anyway. Then Windows XP copied the drivers from the Software Utility CD.

Step 7 Click Finish to complete the installation.

ADSL Router User Manual

Uninstall the USB Driver

FFoorr WWiinnddoowwss 998

Step 1 Click on the Start menu, point to Settings and click on Control Panel.

Step 2 Select Add/Remove Programs.

Step 3 On the Install/Uninstall tab, select USB ADSL Gateway Driver from the list box.

Step 4 Click the Add/Remove button.

Step 5 A confirmation driver deletion dialog box appears, please click the Ye s button.

Step 6 A dialog box appears to ask you to unplug the USB cable. Please unplug it and click OK.

Step 7 Now, the USB drivers are removed.

FFoorr WWiinnddoowwss MME

Step 1 Click on the Start menu, point to Settings and click on Control Panel.

Step 2 Select Add/Remove Programs.

Step 3 On the Install/Uninstall tab, select USB ADSL Gateway Driver from the list box.

Step 4 Click the Add/Remove button.

Step 5 A confirmation driver deletion dialog box appears, please click the Ye s button.

Step 6 A dialog box appears to ask you to unplug the USB cable. Please unplug it and click OK.

Step 7 Now, the USB drivers are removed.

FFoorr WWiinnddoowwss 2200000

Step 1 Click on the Start menu, point to Settings and click on Control Panel.

Step 2 Select Add/Remove Programs.

Step 3 Select USB ADSL Gateway Driver from the list box.

Step 4 Click the Change/Remove button.

Step 5 A confirmation driver deletion dialog box appears, please click the Ye s button.

Step 6 A dialog box appears to ask you to unplug the USB cable. Please unplug it and click OK.

Step 7 Now, the USB drivers are removed.

Chapter 2: Installation

FFoorr WWiinnddoowwss XXP

Step 1 Click on the Start menu, point to Settings and click on Control Panel.

Step 2 Select Add/Remove Programs.

Step 3 Select USB ADSL Gateway Driver from the list box.

Step 4 Click the Change/Remove button.

Step 5 A confirmation driver deletion dialog box appears, please click the Ye s button.

Step 6 A dialog box appears to ask you to unplug the USB cable. Please unplug it and click OK.

Step 7 Now, the USB drivers are removed.

ADSL Router User Manual

Chapter 3: Connection Mode

CChhaapptteerr 33:: CCoonnnneeccttiioonn MMoodde

Prior to configuring the ADSL Router, you must decide whether to configure the ADSL Router as a bridge or as a router. This chapter presents some deployment examples for your reference. Each mode includes its general configure procedures. For more detailed information about web configuration, refer to "Web Configuration".

 Bridge Mode  Router Mode  MER Mode  PPPoA+ NAT Mode  PPPoE + NAT Mode  Multiple PVCs Mode

For making sure that you can connect the ADSL to your computer well and get into Internet successfully, please make sure the following first.

1. Make sure you have installed a network interface card onto your computer.

2. Make sure the connection between the ADSL and your computer is OK.

3. Check to see the TCP/IP protocol and set the IP address as “Auto Get IP Address”.

When you are sure all above is Ok, you can open the Browser and type in “192.168.1.1” and start to do the web configuration with different connection modes.

This chapter is going to introduce the function of each connection mode and tell you the basic configuring steps that you have to do. If you did not follow the configuring steps for using these connection modes, you might get some connection problems and cannot connect to Internet well.

ADSL Router User Manual

Bridge Mode

PC(s)

PPPoE Client S/W

Public IP assigned by BRAS

Default Private IP

192.168.1.1

Bridge

Hub

Mode

ADSL Router

Loop

DSLAM

STM-1

ISP

BRAS

RADIUS

Server

PPP over Ethernet

BRAS Broadband Remote Access Server

Description:

In this example, the ADSL Router acts as a bridge which bridging PC IP address from LAN to WAN. PC IP address can be a static public address that is pre-assigned by ISP or a dynamic public address that is assigned by ISP DHCP server, or can be got from PPPoE software.

Therefore, it does not require a public IP address. It only has a default private IP address (192.168.1.1) for management purpose.

Configuration:

1. Choose a client PC and set the IP as 192.168.1.x (x is between 2 and 254) and the gateway as 192.168.1.1.

2. Start up your browser and type 192.168.1.1 as the address to enter the web-based manager.

3. Go to Configuration >WAN Configuration > Create a New PVC and select the Data Mode –RFC1483

Bridged. Then click Next button.

4. Enter the VPI/VCI values provided by your ISP and select the encapsulation type as LLC/SNAP or VC MUX.

Then click Apply.

5. Save the configuration from System >Save Configuration and System >Restart to restart your router for initiating these settings.

Router Mode

Default Private IP

192.168.1.1 for Management

ADSL

Hub

Router

Loop

Chapter 3: Connection Mode

STM-1

ISP

BRAS

AAA

RADIUS

Server

PC(s)

Public IP(s) Pre-assigned by ISP (+ NAT)

DSLAM

IP over ATM

* BRAS：Broadband Remote Access Server

Description:

In this deployment environment, we make up a private IP network of 192.168.1.1. NAT function is enabled (on ADSL Router or use another NAT box connected to hub) to support multiple clients to access the Router and some public servers (WWW, FTP).

If you apply for multiple IP addresses from your ISP, you can assign these public IP addresses to the ADSL Router and public server, e.g., Web or FTP server. Typically the first IP is network address, the second is used as router IP address and the last one is subnet broadcasting. Other remaining IP addresses can be assigned to PCs on the LAN.

For example: You are given the IP addresses 10.251.2.0 ~ 10.251.2.7. Then:

10.251.2.0 is network IP address

10.251.2.1 is assigned to router IP address.

10.251.2.7 is subnet broadcasting

10.251.2.2~10.251.2.6 can be assigned to public servers on the LAN.

Configuration:

1. Start up your browser and type 192.168.1.1 as the address to enter this ADSL web-based manager.

2. Go to Configuration > WAN Configuration > Create a new PVC. and select the Data Mode –RFC1483 Routed. Then click Next button.

3. Enter the VPI/VCI values provided by your ISP and select the encapsulation type as LLC/SNAP or VC MUX. Then click Apply.

4. Set IP configuration for Local WAN IP Address. Choose Specify an IP Address item. Please set as the following example, IP Address: 10.3.80.105(should be the one that you get from ISP) Subnet Mask: 255.255.255.248(should be the one that you get from ISP) Check on Enable NAT on this interface and click Apply.

5. Go to Configuration > LAN Configuration and set as the following Primary IP: 192.168.1.1, Subnet Mask: 255.255.255.0 Secondary IP: 10.3.80.105, Subnet Mask: 255.255.255.248 (should be the one that you get from ISP) Then click Apply.

6. Go to Configuration > IP Route and click Create a New Route to add a new route. Destination Address: leave default Netmask: leave default Forward packets to: Interface Then click Apply.

7. Go to Configuration > DNS and enable DNS Relay setting and click Next. On the DNS Relay web page, enter the DNS Server IP address, for example 168.95.1.1 (you should get this value from your ISP).

8. Save the configuration from System >Save Configuration and System >Restart to restart your router for initiating these settings.

ADSL Router User Manual

9. Then you have set the web configuration successfully. And you can surf on the Internet.

Note:

If you have multiple PCs on the LAN, you may enable DHCP function on the private or public IP address. The ADSL Router implements a built-in DHCP server, which assigns IP addresses to the clients PCs on the LAN.

+ 60 hidden pages