Askey Computer DPR362 Users manual

CME090W Cable Modem

User’s Manual

Rev:01

2002/09/19

Information in this document is subject to change without notice. No part of this document may be reproduced or transmitted in any form or by any means, electronic or mechanical, for any purpose, without the express written permission of the seller.

The seller provides this documentation without warranty, term, or condition of any kind. The seller may make improvements or changes in the product(s) and/or the program(s) described in this documentation at any time.

Other product and company names herein may be trademarks of their respective owners.

2002/09/19 Rev:01

000083081-cme

EMTA User Manual

Safety Notes

For Installation

Use only the type of power source indicated on the marking labels.

Use only the power adapter supplied with the product.

Do not overload wall outlet or extension cords as this may increase the risk of electric shock or file. If the power cord is frayed, replace it with a new one.

Proper ventilation is necessary to prevent the product overheating. Do not block or cover the slots and openings on the device, which are intended for ventilation and proper operation. It is recommended to mount the product with a stack.

Do not place the product near any source of heat or expose it to direct sunshine.

Do not expose the product to moisture. Never spill any liquid on the product.

Do not attempt to connect with any computer accessory or electronic product without instructions from qualified service personnel. This may result in risk of electronic shock or file.

Do not place this product on an unstable stand or table.

For Using

Power off and unplug this product from the wall outlet when it is not in use or before cleaning. Pay attention to the temperature of the power adapter. The temperature might be high.

After powering off the product, power on the product at least 15 seconds later.

Do not block the ventilating openings of this product.

When the product is expected to be not in use for a period of time, unplug the power cord of the product to prevent it from the damage of storm or sudden increases in rating.

For Service

Do not attempt to disassemble or open covers of this unit by yourself. Nor should you attempt to service the product yourself, which may void the user’s authority to operate it. Contact qualified service personnel under the following conditions:

If the power cord or plug is damaged or frayed.

If liquid has been spilled into the product.

If the product has been exposed to rain or water.

If the product does not operate normally when the operating instructions are followed.

If the product has been dropped or the cabinet has been damaged.

If the product exhibits a distinct change in performance.

Warning

This equipment must be installed and operated in accordance with provided instructions and a minimum 20 cm spacing must be provided between computer mounted antenna and person’s body (excluding extremities of hands, wrist and feet) during wireless modes of operation.

This device complies with Part 15 of the FCC Rules. Operation is s ubject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Caution

Any changes or modifications not expressly approved by the party responsible for compliance could void the authority to operate equipment.

iii

Contents

Before You Use ................................................................................................. vi

Features..................................................................................................vi

System Requirements ...............................................................................vi

Unpacking...............................................................................................vii

Chapter 1: Overview ..........................................................................................1

Physical Outlook ....................................................................................... 1

Front Panel..................................................................................... 1

Rear Panel...................................................................................... 2

Chapter 2: Installation.......................................................................................3

Connecting the Cable Modem to Your Computer............................................ 3

Installation Procedure for Ethernet Interface....................................... 3

Installation Procedure for USB Interface............................................. 3

Chapter 3: Software Installation and Configuration...........................................5

USB Driver Installation .............................................................................. 5

For Windows 98/ME ......................................................................... 5

For Windows 2000/XP ...................................................................... 7

Uninstall USB Driver.................................................................................. 9

For Windows 98/ME ......................................................................... 9

For Windows 2000/XP ...................................................................... 9

Setting TCP/IP on Client PC.......................................................................11

For Windows 98/ME ........................................................................11

For Windows 2000/XP .....................................................................15

DHCP Server...........................................................................................18

For Windows 98/ME ........................................................................18

For Windows NT/2000/XP ................................................................19

For Apple Macintosh........................................................................20

Renew PC IP Address ...............................................................................21

Chapter 4: Web Configuration.......................................................................... 23

Usin4g Web-Based Manager......................................................................23

Status ....................................................................................................23

Software .......................................................................................23

Connection ....................................................................................24

Security ........................................................................................24

Wireless .................................................................................................25

Basic.............................................................................................25

Privacy..........................................................................................25

Advanced ......................................................................................26

Chapter 5: Access Internet through Cable Modem ........................................... 29

Accessing Internet ...................................................................................29

Contents

Chapter 6: Troubleshooting ............................................................................. 31

Appendix: Specifications..................................................................................33

Before You Use

BBeeffoorree YYoouu UUsse

The CME090W is a DOCSIS 1.0/1.1 and CableHome 1.0 compliant wireless cable residential gateway that provide high-speed connectivity to residential, commercial, and education subscribers on public and private networks via an existing cable infrastructure. The CME090W is equipped with 4-port Ethernet switch, USB, IEEE802.11b Wireless, HPNA interfaces. The CME090W can inter-operate with any DOCSIS and CableHome compliant headend equipment. The IP traffic can transfer between the CME090W and DOCSIS and CableHome compliant headend equipments. The data security secures upstream and downstream communications.

Features

Up to 42.88 Mbps downstream and up to 10.24 Mbps upstream, two-way cable modem.

F-Connector for the cable interface.

Build-in IEEE 802.11b Wireless Access Point function

Bridging wired & wir el es s segme n t s of network

Provide 11 / 5.5 / 2 / 1 Mbps wireless connectivity to the wireless clients

Support Wired Equivalent Privacy Algorithm (WEP)

Roaming by Association/Re-association/De-association

Four ports 10/100BaseT Ethernet switch with auto-negotiation function and auto-media d ependent interface crossover (MDIX).

USB Connector for USB interface

Home PNA 2.0 support

NAT (Network Address Translation) to support multiple users with one IP account for routing mode.

Transparent bridging for IP traffic for bridge mode

Firewall function

RSA and 56 bit DES data encryption security

Interoperable with any DOCSIS and CableHome compatible headend equipment

SNMP v1/v2c/v3 network management support

Remote operating firmware downloading

Support Web pages and private DHCP server for status monitoring

Clear LED display

Universal Plug and Play

System Requirements

This cable modem equips ETHERNET and USB interfaces. You can choose either one to connect to the cable modem. Before installing the EMTA, please check the following requirements with your computer.

For Ethernet Connection

Windows98/2000/NT/ME/XP operating system or Apple Macintosh series

10/100 Base-T NIC(network interface card)

Subscribe to a Cable Television Company for cable modem service

For USB Connection

ADSL Router User Manual

Windows98/2000/ ME/XP operating system

Available USB port

Subscribe to a Cable Television Company for cable modem service

For Phone Connection

Standard touch-tone telephone and phone cord with RJ-11 connector

Subscribe to a VoIP system company (VoIP service provider) for VoIP services

Unpacking

Check the contents of the package against the pack contents checklist below. If any of the items is missing, then contact the dealer from whom the equipment was purchased.

Cable Modem

Twi sted Pair Ethernet Cable (CAT5/RJ-45)

USB Cable

Power Adapter & Power Cord

Quick Start Guide

Software CD

vii

Chapter 1: Overiew

CChhaapptteerr 11:: OOvveerrvviieew

Physical Outlook

FFrroonntt PPaanneel

The following illustration shows the front panel of the EMTA machine:

LED Indicators

The LEDs on the front panel are described in the table below (from left to right):

LED Color Status Description

Receive

Green

Off Power off.Power Green On Power on. Blinking Indicates receiving RF DS data

Send Green Blinking To indicate transmit RF US traffic.

On Modem registration completed.Cable Green

To indicate RF link status at different speed.

1. Scanning DS

2. US rangi ng

3. DHCP/TFTP/Registration

To indicate HPNA link is present.

To indicate wireless link is present.

Green

~ 4

HPNA Green

Wireless Green

Blinking

On Ethernet carrier is present.Ethernet 1 Blinking To indicate Ethernet data. On To indicate USB link is present.USB Green Blinking To indicate USB transmitting or receiving data On Blinking To indicate HPNA transmitting or receiving data On Blinking To indicate Wireless AP transmitting or receiving data

Cable Modem User’s Manual

RReeaarr PPaanneel

12VDC: 12V Power connector HPNA: RJ-11 Home PNA Connector RST︰︰︰︰ Reset-to-Default push button

ETHERNET︰︰︰︰ Ethernet 10/100BaseT RJ-45 connector USB：：：： USB Connector CABLE︰︰︰︰ F-Connector

Chapter 2: Installation

CChhaapptteerr 22:: IInnssttaallllaattiioon

This cable modem equips USB and Ethernet interfaces. You can choose either one to connect to the cable modem. Go to the section “Installation Procedure for Ethernet Interface”, if your computer has installed TCP/IP and Ethernet card with 10/100BaseT capability. Go to the section “Installation Procedure for Ethernet USB Interface”, if your PC has USB port and the operating system is Microsoft Windows 98/ME/XP or Windows 2000.

Connecting the Cable Modem to Your Computer

IInnssttaallllaattiioonn PPrroocceedduurree ffoorr EEtthheerrnneett IInntteerrffaacce

Follow the steps below for proper installation

1. Make sure your computer meets the system requirements.

2. Connect a coaxial cable (supplied by the local Cable Television Company) to the CABLE connector on the modem.

Note: To speed up the registration process of cable modem, the coaxial cable should be connected to the modem prior to the power connector.

3. Connect the RJ-45 Ethernet cable to one of the ETHERNET connector on the modem, connect the other end with the 10/100BaseT Ethernet port on your computer.

4. Plug the power adapter into the POWER connector of the modem.

5. Plug the other end of the power adapter into a power outlet.

6. The cable modem will look for the proper cable modem signal in the Cable Television network and process the initial registration. The cable modem is ready for data transfer after the LED “Power” is in solid green.

Note: The RST button at the rear panel is for maintenance purpose only.

IInnssttaallllaattiioonn PPrroocceedduurree ffoorr UUSSBB IInntteerrffaacce

Follow the steps below for proper installation

1. Make sure your computer meets the system requirements.

2. Connect a coaxial cable (supplied by the local Cable Television Company) to the CABLE connector on the modem.

Note: To speed up the registration process of cable modem, the coaxial cable should be connected to the modem prior to the power connector.

3. Connect the USB cable to the USB connector on the modem.

4. Plug the power adapter into the POWER connector of the modem.

5. Plug the other end of the power adapter into a power outlet.

Note: The RST button at the rear panel is for maintenance purpose only.

Below shows the connection status among the cable modem and your computer.

Cable Modem User’s Manual

Chapter 3: Software Installation and Configuration

CChhaapptteerr 33:: SSooffttwwaarree IInnssttaallllaattiioonn aanndd CCoonnffiigguurraattiioon

USB Driver Installation

FFoorr WWiinnddoowwss 9988//MME

1. Wait for the cable modem is running in the operational state (registration O.K.). Plug the USB cable into your PC USB port. You will see the next page. Click the “Next” button.

2. Select “Search for the best drivers for your device“ and click the “Next” button.

3. Check “Specify a location” and browse CD-ROM:\Win9x or WinME. Click the “Next” button.

+ 29 hidden pages