ASK HCRRDDE0207523 User Manual
HAND-HELD READER
HCR 800/805
USER MANUAL
Menu
1
4
ghi
7
pq rs
ab c
2
jkl
5
tuv
8
0
OK
An nul
d ef
3
mno
6
wxyz
9
#
RD-MU-02161-13 1/1 07/07/03
FCC Compliance Statements
This equipment has been tested and found to comply with the radiated limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide a reasonable protection against harmful interferences in a residential
installation. This equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try the correct interference by one or
more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC rules. Operation is subject to the following
two conditions. (1) This device may not cause harmful interferences. And (2) this device
must accept any interference received, including interference that may cause undesired
operation.
The ASK HCR800/HCR805 readers were submitted and a grand of authorization
received from the FCC as device under the intentional radiator requirements of Part 15,
Subpart C.
Caution: Any changes or modification not approved by ASK could void user’s authority
to operate the equipment.
CE Compliance statement
The ASK HCR readers are in conformity with European requirements, this product has
been assessed to the following standard:
EN 300330
EN 301 489-3
EN 60950-1 / IEC 60950-1
RD-MU-02161-13 2/19 07/07/03
Table of contents
1 – FIRST USE 4
1.1 Unpacking 4
1.2 HCR 800 overview 4
1.3 Strap installation 5
1.4 Strap adjustment 6
1.5 Belt base using 6
2 – BATTERY RECHARGING 6
3 – SAM MODULES SETUP 7
4 – APPLICATIVE SOFTWARE LOADING 8
5 – USE 8
5.1 ON/OFF 8
5.1 Contactless card 8
5.2 Contact card 8
6 –TECHNICAL FEATURES 9
7 – TROUBLESHOOTING – AUTOTEST 10
RD-MU-02161-13 3/19 07/07/03
1 – First use
1.1 Unpacking
Check in packaging box if following items are present:
-1 hand-held reader
-1 belt base
-1 holding strap
1.2 HCR 800 /805 overview
A ntenna location
Graphic display
160 pl x 16 0 pl
ON/OFF
key
(press 3s.)
Menu
Control leds
OK
Annul
Browser
keys
1
4
ghi
7
pqrs
abc
2
jkl
5
tuv
8
0
def
3
mno
6
wxyz
9
#
A lphanumeric
K eys
RD-MU-02161-13 4/19 07/07/03
Contact card slot
Ho lder strap
x 6 screws for
ID label
HCR 800
Type : DE-075-0
Serial 024401
1
bottom case closure
made in France
Connector for battery charging
1.3 Strap installation
Insert the strap into the holder upper strap ring, then into the lower ring, after, bend back the two
sides of the strap as shown in the following figure.
RD-MU-02161-13 5/19 07/07/03
1.4 Strap adjustment
The strap should be adjusted to the user’s hand. For that, it is necessary to move the two straps
part (Velcro covered) in order to have the required space.
1.5 Using belt base
Belt base should be locked on belt vertically from top to bottom. The HCR goes to belt base via
the riveted button on the strap. Reader is inserted from bottom to top. For extracting, apply a
pressure with one hand to the two lateral buttons of the base, with the other hand lift the hand held reader up.
2 – Battery recharging
Before first use, the HCR should be inserted in its base station for five hours minimum for
battery charging completion.
The next recharge will depend on the battery discharge. Internal battery uses li-ion technology,
that means it doesn’t have memory effect. The internal battery can be charged at any time,
without capacity waste.
Reader setup
USB cable to PC
Me nu OK
An nu l
1
4
ghi
7
pqrs
d ef
3
abc
2
mno
6
jk l
5
wxyz
9
tuv
8
#
0
Ch arging red ligh t indicator
The docking station should be connected to a computer via an USB port. No other connection is
required. The docking station’s light should bright, three colors are possible :
- Orange : docking station power is ON
RD-MU-02161-13 6/19 07/07/03
Loading...