
Component-holder
cartridge
with UL94V-0 polyamide
insulating body
• to be mounted on MPFA.4, DSFA.4 and
HMFA.2 (see page 84)
• a fuse Ø 5 x 20 mm can be inserted (our
type F5, with or without signalling LED,
diode (1 or 3 A), brass pin Ø 5 x 20 mm and
other components (e.g. resistors)
Terminal
block
MPFA.4 + CPF/5
DSFA.4 + CPF/5
HMFA.2 + CPF/5
Max. dissipated power – In conf. with IEC 60947-7-3
Voltage
Current [A]
[V] (*)
250 6,3 1,6 1,6 4 1,6
250 6,3 1,6 1,6 4 1,6
250 6,3 1,6 1,6 4 1,6
Protection against overload and short circuit Only protection against short circuit
Single configuration
(PV) - [W]
Composite configuration
(PV) - [W]
Single configuration
(PV) - [W]
Composite configuration
(PV) - [W]
standard version
CPF/5
Cat. No. CPF05
TECHNICAL CHARACTERISTICS
function / type component-holder cartridge
rated cross-section (mm
connecting capacity
flexible (mm2)
rigid (mm2)
max. flexible with ferrule (mm2)-ferrule type
rated voltage / rated current / gauge co
rated voltage / rated current / AWG
(Ex e) rated voltage / (V)
rated impulse withstand voltage / pollution degree
insulation stripping length (mm)
tightening torque value (test / recommended) (Nm)
height / width / thickness
height / width / thickness
height / width / thickness
nf. to IEC 60947-7-1
/ tightening torque value UL
TH/35 7,5 mm
TH/35 15 mm
G32
APPROVALS
ACCESSORIES
Marking tag printed or blank
Tinned brass conductor Ø 5 x 20 mm
Cartridge / insert with 1 A diode
Cartridge / insert with 3 A diode
VERSIONI PREDISPOSTE
With non-polarized LED microcircuit 12 Vdc / Vac
With non-polarized LED microcircuit 24 Vdc / Vac
With non-polarized LED microcircuit 48 Vdc / Vac
With non-polarized LED microcircuit 115 Vdc / Vac
With non-polarized LED microcircuit 230 Vdc / Vac
With 1 A diode (1N4001 ÷ 1N4007 types)
With 3 A diode (BY255 type)
With resistor 1200 Ω (1 W ± 5%)
Note:
(a) with fuse ø 5 x 20 mm, 250 V, Imax = 6,3 A – with brass pin Imax = 10 A
(b) total value, when the cartridge is mounted on terminals, considering as well the mounting rail:
2
)
-
-
-
320 V (a) / 6,3 A (a) / A5
-
4 KV / 3
-
(b) / 33 / 6
(b) / 33 / 6
(b) / 33 / 6
Approvals referred to the terminal blocks, on
which the cartridge is mounted – see table
Type Cat. No.
CNU/8 NU...
CO/5 VL103
SFR/I1A (with 1 A diode) SF992
SFR/I3A (with 3 A diode) SF993
Type Cat. No.
CPF/5L12 CPF512
CPF/5L24 CPF524
CPF/5L48 CPF548
CPF/5L115 CPF511
CPF/5L230 CPF523
CPF/5D1A CPF501
CPF/5D3A CPF503
CPF/5R CPR05
The cartridge can
contain a spare fuse,
instead of the LED
signalling circuit.
Terminal block
HMFA.2 57 75 MPFA.4 75 83 79
DSFA.4 96 104 100
Height on rail
TH/35 7,5 (mm)
Height on rail
TH/35 15 (mm)
Height on rail
G32 (mm)
View of the different choices for mounting the cartridge respectively on terminals
DSFA.4, MPFA.4 or HMFA.2.
When the cartridge is mounted on HMFA 2 terminals, adjoining one
another, a terminal strip must be envisaged between one terminal and
the next, because of the pitch differential between terminal and cartridge.