Ashly WR-4 User Manual

Audio Tools for the True Professional

WR-4 Active Remote Operating Instructions

The WR-4 is a microprocessor-controlled wall remote control unit for the 24.24M matrix
processor designed to allow zoned source selection and zone volume control. The WR-4
controls the 24.24M input channel source selection of th e specified output channel using the
six upper selection keys. The WR-4 will also allow control of the output channel volume
using the two lower keys. To select an input audio source, simply press one of the six
corresponding input select keys. Multiple input sources may be assigned to a single select
key, and also multiple selected keys may be engaged at a given time. Select keys that are
currently engaged will have their corresponding LED lit. To deselect an input source, simply
press the corresponding key again. To change the output volume, simply scroll the up and
down arrow volume control keys. The WR-4 installs in a st andard wall-mounted electrical
box. Up to four WR-4 or WR-3 wall remotes can be phantom-powered from a 24.24M main
unit. Connection to the 24.24M is via the Data In and Data Out terminals on the rear of the

24.24M, and can communicate up to 1,200 feet (365 meters). Additional wall remotes can
be used provided an external power supply is properly connected (see section xx.x).

When pressing a source select key, the corresponding LED may take up to a second to
respond because the remote is communicating the command to the 24.24M and waiting for
a confirmation reply from the 24.24M before changing the corresponding LED indicator.

The WR-4 must be programmed with the input channels to be selected by the source select
keys, and the output channel that is con trolled by the volume control keys. The WR-4 is
programmed using it’s own pushbutton keys when powered by a 24.24M main unit. To
program the WR-4, follow the programming instructions below.

To program the Device ID of the 24.24M device that the WR-4 will control:

1. Simultaneously press select keys one and six to enter the DEVICE ID PROGRAMMING
MODE. The first select LED will start flashin g indicating it is in the Device ID
programming mode.

2. The number displayed in the numeric LED display is the Device ID of the 24.24M that
the WR-4 will control. Simply scroll the up and down arrow key s to change the
Device ID.

3. Press select keys one and six together again to accept the Device ID and return to
normal operating mode.

4. Programming modes can be disabled from being activated from the front panel keys
by switching the rear-side red switch number one to ON.

Ashly Audio Inc. 847 Holt Road Webster, NY 14580 [phone] [phone]
internet: http://www.ashly.com email : [e-mail] fax: [phone]

To program the output channel whose volume and source selection will be
controlled by the WR-4:

1. Simultaneously press select keys two and six to enter the OUTPUT CHANNEL
CONTROL PROGRAMMING MODE. The second select LED will start flashing indicating
it is in the Output Channel Co ntrol Programming Mode.

2. The number displayed in the numeric LED display is the output channel of the

24.24M that the WR-4 will control. Simply scroll the up and down arrow keys to
change the output channel that the WR- 4 will control.

3. Press select keys two and six together again to accept the output channel number
and return to normal operating mode.

4. The output channel volume control feature of the WR-4 can be disabled by switching
the rear-side red switch number two to ON.

To program the sources which will be selected when each select key is depressed:

1. Simultaneously press select keys three and six to enter SOURCE SELECT
PROGRAMMING MODE. The select LED of the curren t select button will start flashing
indicating the unit is in the Source Select Programming Mode.

2. Press any one of the six select keys to begin programming the input channel sources
to be selected by that source select key. The corresponding select LED w ill start
flashing indicating the WR-4 is in programming mode of source selection for that
key.

3. Press the up and down arrow keys to scroll through the input channels. If an input
channel is assigned to be selected by the currently flashing select key, then the input
channel number will be flashing on the numeric LED display. To select or deselect an
input channel assigned to the source select key, simply press the currently flashing
select key.

4. Press both the up and down keys together to accept the source select assignments
and return to the normal operating mode.

5. Programming modes can be disabled from being activated from the front panel keys
by switching the rear-side red switch number one to ON.

To program the options applied to the WR4:

Options Available

• Exclusive source selection (when a source is selected all others are turned off)

• Biamped operation – both the current channel and the next channel will be adjusted

when this option is enabled.

Programming Instructions

1. Simultaneously press select keys four and six to enter the OPTION PROGRAMMING
MODE. The fourth select LED will start flashing indicating it is in the Option
Programming Mode.Press the up or down keys to change options.

2. Press the fourth select key to turn on or off an option. If an option is turned on the
displayed option number will flash.

3. Press both the up and down keys together to exit the programming mode.

Lockout Functions:

Programming Modes may be locked out so they cannot be inadvertently modified by
switching Switch 1 (on the Back of the WR4) to the On Position

Ashly Audio Inc. 847 Holt Road Webster, NY 14580 [phone] [phone]
internet: http://www.ashly.com email : [e-mail] fax: [phone]