ASCO Accessories Series 610 Manuals & Guides

MOTORFLOW

D

GB

FR

DE

Motorised Control Valve

Vanne Motorisée

Motorregelventil

Series - Série - Baureihe 610

Installation manual

Manuel d'installation

Installationshandbuch

IM14219-R03

GB

FR

DE

ESD

!

SUMMARY - SOMMAIRE - INHALT

English version

1. Introduction .........................................................................................................................................................3

2. Cable connection................................................................................................................................................. 3

3. Electrical connection ........................................................................................................................................... 3

4. LED indicators ..................................................................................................................................................... 4

5. Manual position adjustment................................................................................................................................. 4

6. Auto adapt ........................................................................................................................................................... 4

8. Cascaded control ................................................................................................................................................ 4

8. Frequency imput ..................................................................................................................................................4

9. Technical characteristics ..................................................................................................................................... 5

10. Accessories ......................................................................................................................................................... 5

11. Dimensions and weight ....................................................................................................................................... 5

Version française ........................................................................................................................................... 6

Deutsche Version .................................................................................................................. 10

This product contains electronic components sensitive to electrostatic

CAUTION

OBSERVE PRECAUTIONS

FOR HANDLING

ELECTROSTATIC SENSITIVE

DEVICES

CAUTION! Dangerous operating conditions may occur when using the programming interface on the valve as the valve may possibly
not react to the analog setpoint any more.
Provide for protection against uncontrolled movement of equipment when putting the valve into operation and before making any
modifications to the valve settings.

We herewith declare that the version of the product described in this installation manual is intended to be incorporated into or assembled with other
machinery and that it must not be put into service until the machinery into which it is to be incorporated has been declared in conformity with the
provisions of Council Directive 2006/42/EC.
Handling, assembly and putting into service and all settings and adjustments must be done by qualified, authorised personnel only.

This product complies with the essential requirements of the EMC Directive 2014/30/EU and its amendments. It is CE-approved.
A separate Declaration of Conformity is available on request.
Please provide ordering code and serial numbers of products concerned.

The information in this manual is subject to change without notice.

In no event shall ASCO NUMATICS be liable for technical or editorial errors or omissions. Neither is any liability assumed for accidental
or consequential damages arising out of or in connection with the supply or use of the information contained herein.
THIS MANUAL CONTAINS INFORMATION PROTECTED BY COPYRIGHT. NO PART OF THIS DOCUMENT MAY BE PHOTOCOPIED
OR REPRODUCED IN ANY FORM OR MANNER WHATSOEVER WITHOUT PRIOR WRITTEN PERMISSION FROM ASCO NUMATICS.

COPYRIGHT © 2016 - ASCO NUMATICS - All rights reserved.

discharge. An electrostatic discharge generated by a person or object
coming in contact with the electrical components can damage or destroy
the product.
To avoid the risk of electrostatic discharge, please observe the handling
precautions and recommendations contained in standard EN 100015-1.
Do not connect or disconnect the device while it is energised.

NOTICE

IM14219-2

INSTALLATION

MOTORFLOw

4

1

3

2

4

132

➞

➞

GB

1. INTRODUCTION

The
A DC motor controls the opening width to regulate the flow. A potentiometer is integrated into the electrical actuator to

D

is a motorised control valve designed to control the flow of liquids.

capture the position. A microcontroller enables digital control. Two buttons are provided for manual control. The setpoint
is displayed in % (0-100%).
A PC software and the RS232 interface allows modification of settings and parameters and data recording.
The position is maintained on loss of power. The actuator remains in its current position.

2. CABLE CONNECTIONS

LEDS

M12 male connector

(power supply:

setpoint/feedback)

Display

Cover

RS232 interface

Buttons

M12 female connector

(external sensor)

3. ELECTRICAL CONNECTION

Male connector pinning (power supply)

+ 24 V DC, supply 1

analog setpoint input 2

supply ground 3

analog ground

analog output (feedback) 4

digital output (pressure switch) 5

(1)

A 6-wire cable with separate analog ground is used for cable lengths over 2 m to set off the voltage drop for the setpoint.

(2)

The housing of the M12 male connector/M12 female connector is connected to the valve body.

EMC shield Housing

(1)

M12

5

(2)

5-wire cable

(2 m)

brown brown

white white

blue green

black pink

grey grey

shield shield

6-wire cable

(5 m, 10 m)

yellow

Female connector pinning (sensor)

+ 24 V DC, supply 1

external feedback input 2

supply ground 3

frequency input 4

unused 5

EMC shield Housing

M12

5

(2)

All leaflets are available on: www.asconumatics.eu

IM14219-3

INSTALLATION

MOTORFLOw

MOTORFLOw

MOTORFLOw

MOTORFLOw

GB

4. LED INDICATORS

Red LED Low or overvoltage (flashing)
Green LED Pressure switch
Yellow LED Manual operation

5. MANUAL POSITION ADJUSTMENT (manual operation)

During power up after an interruption in the power supply, press both arrow buttons located beneath the display to switch
to the manual mode. The operating mode is indicated by the letters "H n d" in the display.
This display disappears after having pressed the arrow buttons to show the current setpoint.
Use the arrow buttons to change the setpoint which changes the opening width.
Exit this operating mode by pressing both arrow buttons simultaneously or by turning off the power supply for a short
time.

6. AUTO ADAPT (automatic setting of stop positions)

To enter the Auto-Adapt mode, simultaneously press and hold both buttons located underneath the display for at least 3
seconds. The Auto-Adapt operating mode is indicated by the letters "AdA" in the display.

Then release and push both buttons again for at least 3 seconds to start the auto-adapt procedure. “OPn” is displayed
to indicate the opening process. The module moves into the “open” position until a current increase of the motor occurs
at the open position stop. The module then moves into the “closed position“. “CLO” is displayed to indicate the closing
process. In this case too, the closed position stop is established by the current increase in the motor.
Successful setting of both stop positions is indicated by the letters “END” in the display.
Press the left button to complete the procedure and return the

Errors are immediately displayed.
E 1 Timeout error (> 2 sec) for open stop position
E 2 Plausibility check for open stop position failed
E 3 Timeout error (> 2 sec) for closed stop position
E 4 Plausibility check for closed stop position failed
Push both buttons for at least 3 sec. to delete the error display and return the
mode.

In the event of an error, the previous stop position settings are restored.

D

into its normal operating mode.

D

into its normal operating

7. CASCADED CONTROL

A closed control loop for flow, pressure, temperature etc. can be set up with the
The setpoint is compared to the feedback signal received from the external sensor and the valve opens or closes to
reach the desired value. Maintaining the mechanical position control allows to stabilise the control loop.

D

and an external sensor.

8. FREQUENCY INPUT

Flow rate sensors with turbine technology for liquid monitoring can be directly connected to the frequency input of the

max. 5000 Hz frequency.
To adapt the frequency input (npn or pnp polarity and frequency range) to your needs, please contact our Product Sup­port.

All leaflets are available on: www.asconumatics.eu
IM14219-4

D

. Turbine flow rate sensors with either npn or pnp outputs can be used. The frequency input can process

INSTALLATION

108

138

GB

9. TECHNICAL CHARACTERISTICS

Electrical characteristics

Setpoint 0-10V; 0/4-20mA
Feedback 0-10V; 0/4-20mA
Supply voltage 24VDC ±10%
Power rating max. 10W
Actuating time 2 sec.

Operating conditions

Ambient temperature 0...+50 °C
Storage temperature -20...+70°C

10. ACCESSORIES

description catalogue number

Straight M12 female connector, 5 pins, with screw terminals
Right-angle M12 female connector, 5 pins, with screw terminals

88100256
88100725

Supply cable 2 m, 5x0,25 mm², straight connector 88100726
Supply cable 2 m, 5x0,25 mm², right-angle connector
Supply cable 5 m, 6x0,56 mm², straight connector
Supply cable 5 m, 6x0,56 mm², right-angle connector
Supply cable 10 m, 6x0,56 mm², straight connector
Supply cable 10 m, 6x0,56 mm², right-angle connector
RS-232 cable for PC connection
Software tool for PC “Asco-MotorCom” available for download from our website at

www.asconumatics.eu

88100727
88100728
88100729
88100730
88100731
88100732

-

11. DIMENSIONS (mm), WEIGHT (kg)

M12 (2x)

126.1

56.1

16.5

80

140

85

3/4

30

55.1

1 2

3

20

29

54.5

4

5

80

weight

1,1

A Display of setpoint (0-100%)
Z Operating buttons (manual operation)
E Power supply
R Sensor input
T Programming port

Availability, design and specifications are subject to change without notice. All rights reserved.

All leaflets are available on: www.asconumatics.eu

IM14219-5