Asante Technologies FS4016P User Manual
FS40016P.fm Page 1 Tuesday, March 16, 1999 5:53 PM
Asanté FriendlyNET FS4016P Installation Guide
Asanté FriendlyNET FS4016P
16-port Dual-speed Fast Ethernet Switch
User’s Guide
Product Introduction
Congratulations on your purchase of the Asanté FriendlyNET FS4016P. These switches were
designed to give you the ultimate in performance, flexibility, ease-of-use, and reliability.
Your Asanté FriendlyNET FS4016P can increase performance on your network by bringing full Ethernet bandwidth to individual workgroups, or straight to the desktop, instead of requiring all stations to
share the bandwidth of a single network. The switch’s 100Mbps Fast Ethernet capability can eliminate
bottlenecks in connections to servers, or can link 10Mbps workgroups to a 100Mbps F ast Ethernet network backbone.
For straight-through 10Base-T/100Base-TX connection to servers and workstations, the switch supports full-duplex connection, effectively doubling the total throughput on individual links. The switch’s
store-and-forward switching architecture forwards packets to their destination with a minim um of delay.
The switches can be placed on a tabletop or wall-mounted, and provide the ideal solution for your
small, medium, or large Ethernet/Fast Ethernet network. It is designed to comply fully with the IEEE
802.3 Ethernet and 802.3u Fast Ethernet standards.
Page 1
FS40016P.fm Page 2 Tuesday, March 16, 1999 5:53 PM
Asanté FriendlyNET FS4016P Installation Guide
Package Contents
1. Asanté FriendlyNET FS4016P 16-port 10/100M Switch
2. Self-adhesive rubber pads for desktop installation
3. AC Power cord
4. Rack Mounting kit for rack installation
5. Installation guide
If any of these items are missing, contact your dealer immediately
Installation
The Asanté FriendlyNET FS4016P switch is easy to install and requires no special training. You
should, however, read the following instructions carefully before proceeding to install your switch. The
diagram below shows the layout of the front and rear panels.
Front & Rear Panel of the Asanté FriendlyNET FS4016P
LED display
Full
Auto
81
Full/Auto dip switches
1
1
9
9
169
9
9
Uplink Push Button
168
8
16
16
Normal/Uplink
Normal/Uplink
100-240VAC
Page 2
∆
∆
∆
FS40016P.fm Page 3 Tuesday, March 16, 1999 5:53 PM
Asanté FriendlyNET FS4016P Installation Guide
The Asanté FriendlyNET FS4016P is designed for easy “plug and play” installation. Before you connect your switch to other devices, there are several issues you should keep in mind:
When connecting the switch to a workstation using unshielded twisted pair
cable, you must make sure that the cable length is not greater than 100 meters.
10Base-T twisted pair Ethernet cabling should be category 3 or better, and
100Base-TX twisted pair Fast Ethernet cabling should use tested category 5
cabling.
Network cable segments can be connected to, or disconnected from the
switch while the power is on. Plugging in or removing network cables while your
switch is operating will not interrupt the operation of the switch.
When placing your switch, you need to avoid dusty locations and electromagnetically noisy areas.
Desktop Placement
You can place the switch on a table. In this case, use the four self-adhesive feet, which are provided
with the Asanté FriendlyNET FS4016P for cushioning purposes. Stick them on the four corners of the
bottom surface of the switch, as shown in diagram below to cushion it against vibration.
Uplink
12345
12345
FS4005P
Link/Activity
Collision/FullDuplex
PWR
5-port Dual-speed Ethernet Switch
FriendlyNET
Page 3
FS40016P.fm Page 4 Tuesday, March 16, 1999 5:53 PM
Asanté FriendlyNET FS4016P Installation Guide
Connecting to Servers and Workstations
Use the following procedure to connect a 10Base-T or 100Base-TX Ethernet server or workstation to the switch.
1. Make sure that the length of the straight-through cable between the switch and the station does
not exceed 100 meters, including all patch cables and cross-connect wires.
2. Connect one end of the cable to the RJ-45 connector on the switch, and the other end to the station.
Page 4
10Mbps
workstation
5 4 3 2 1
Connection cable may be up to 100 meters long
100Mbps
workstation
10Mbps
workstation
100Mbps
workstation
100Mbps
workstation
Loading...