Attention
Please read the operating manual prior to operating the machine for the first time.
2
6220 F
1
2 3
4
Açma / Kapatma
Ekonomi
9
On/Off indicator light
1
Programme selection knob
Rinse-aid level indicator light
2
3
Salt Level Indicator light
4
5
Half Load
6
Start/Pause button
How to use your dishwasher:
Open the water tap.
Plug to the mains.
Open the door and load the dishwasher. Check if both upper and lower
spray arms move freely.
Fill enough detergent into the detergent dispenser and close the door.
Use the on / off button to turn the machine on.
Check the salt and rinse aid level indicator lights (depends on the model).
If necessary, refill salt and/or rinse aid.
Use the program selection knob to choose your washing program.
1
2
Yoðun
65°C
50°C
1
Parlatýcý
2
Az
Bulaþýk
8
5
Start the program with the Start/Pause button:
Attention
Avoid opening the door during the washing process. This interrupts the
washing process, and hot steam will escape. When the door is closed, the
program will continue.
Use the on / off button to turn the machine off again.
When the progress indicator light program end lights up, the program is
complete.
Close the water tap.
Pull out the plug.
Allow your dishes to cool for 15 minutes, with the door open.
Unload the dishes. Begin with the lower basket.
Açýk/Kapalý
Tuz
Yýkama
Kurutma
Baþla
Bekle
Bitti
Ýptal
3 sn.
6 7
7
LED progress indicator lights
8
Door handle
9
On/Off Button
PROGRAM TABLE
Program number
1
Reference **
Ekonomi
Program name
Cleaning temperature
Suited to
Degree of dirtiness
Detergents
15 cm³
15-25 cm³
+ 5 cm³
Program process
Duration (min)
Energy (kWh)
Water (I)
The consumption values shown in the table were determined under standard conditions. For this reason, deviations are possible under practical conditions.
** Reference program for test institutes
The tests in accordance with EN 50242 must be carried out with a full salt container of the water softener, a full reservoir for the rinse aid and the testing program.
Eco
50°C
Normally dirty
dishes with starch
containing food
leftovers which
are not dried on
Medium
x
x
Pre-wash
W
ash
Cold rinse
Hot rinse
Dry
End
136
1,05
15
2
Süper
Intensive
70°C
Especially dirty
dishes with food
leftovers which
are dried on
High
x
x
Pre-wash
Wash
Cold rinse
Hot rinse
Dry
End
115
1,67
17,5
Function buttons Control indicator lights
6220 F
On/off button
You turn your dishwasher on / off with this button. When turning
on, the indicator light for the last used program will light up.
Start/Pause button
You use this button to start the selected program; the light on
the button lights up.
Stop the program with the start / pause button if you would like
to open the door once the dishwashers washing program is
running.
Program selection Knob
Use the program selection Knob to choose your washing
program.
How to cancel the washing program
To cancel a program while the machine is operating:
Press start/stop button for 3 seconds. The machine will drain
the water inside the machine for 45 seconds. The program is
cancelled when washing light goes off. Then, you can choose
and start a new program.
! Important: Depending on the stage of the program you
have cancelled, there may be detergent residue or rinse aid
inside the machine and on the load. Make sure the items in
the dishwasher are not used before washing properly.
2
Rinse aid level indicator light
You can also tell whether rinse aid must
2 3
be refilled by looking at the rinse aid
dispenser. When the visual fill indicator
is dark, there is enough rinse aid in the
dispenser.
(Rinse) (Salt)
3
Salt level indicator light
When the colour is light, open the
dispenser and refill rinse aid.
When this indicator light comes on, you
2 3
must refill special salt.
In machines which do not possess an
electrical salt indicator, the salt content
can be read on the container for the salt.
When the visual fill indicator is dark, there
(Rinse) (Salt)
is enough salt in the container.
When the colour is light, open the
container and add dishwasher salt.
Full
Empty
L
A
Z
S
T
L
U
E
Z
S
S
T
A
L
L
A
Z
S
T
L
U
E
Z
S
S
T
A
L
How to change the washing program
To change the program selection while the machine is operating:
Press start/stop button. The washing light will go off.
Select the new program. Press start/stop button. The washing
light will be on and new program will start.
! Important: The new program will NOT right from the
beginning. It will start from the stage last carried out by the
previous program selection.
2
Alternatif
Yýkama
Half Load (1/2) button
When there are few dishes, you press this button after pressing
the programme selection button. When turning the dishwasher
on, the indicator light on the button lights up. This function
helps you to save water and energy.
Ýptal
3
7
LED progress indicator lights
The program sequence throughout the washing
process can be monitored from the progress indicator
( Wash )
( Dry )
( End )
lights on the control panel.
Following the washing stage, in order to drain
and remove water from inside the machine
completely, the machine will pause for
approximately 35 minutes. Do not worry this is
not a fault. Then End progress indicator light
will come on.
Do not switch the machine off before End light
comes on.
7
18 9901 2270-00
Loading...