Artusi CAFG91B, CAFG90X, CAFG91X User Manual

CAFG90X

CAFG91X

CAFG91B

OPERATION MANUAL

APPLIANCES

FOR LIVING

Congratulations, you are now the proud owner of an ARTUSI cooking appliance. Thank you for purchasing ARTUSI

and welcome to the ARTUSI Family.

This instruction manual has been specially created to inform you of the full range of features your ARTUSI appliance

has to offer and serves as an introduction to getting the very best out of your ARTUSI appliance.

We present detailed information on each of the features your ARTUSI appliance consists of. Once you have read

this section you will be able to choose the most appropriate settings for your appliance when cooking different

types of food.

We ask you to read the instructions in this booklet very carefully as this will allow you to get the best results from

using your appliance. KEEP THE DOCUMENTATION OF THIS PRODUCT FOR FUTURE REFERENCE.

TO REGISTER YOUR PRODUCT WITH ARTUSI, PLEASE FILL OUT THE WARRANTY CARD AT THE END OF

THIS BOOKLET AND POST IT TO: REPLY PAID 83617

LEICHHARDT NSW 2040

Dear Artusi Customer, please read this user manual carefully before using the product and, keep it permanently at

your disposal.

Note: This user manual is prepared for more than one model. Some of the features specified in this Manual may not

be available on your appliance.

All our appliances are only for domestic use, not for commercial use. Products marked with (*) are optional.

“THIS APPLIANCE SHALL BE INSTALLED IN ACCORDANCE WITH THE REGULA TIONS FORCE AND ONLY USED

IN A WELL VENTILATED SPACE. READ THE INSTRUCTIONS BEFORE INSTALLING OR USING THIS APPLIANCE”

“Conforms with the WEEE Regulations.”

Getting to know your new cooker

Thank you for choosing one of our products.
Our cookers are of simple, rational design. They are
constructed to the best standards to ensure good
service and outstanding safety.
Please read this manual carefully; it will provide all the
advice needed to allow you to obtain the best results from
the very first day.

RECORD HERE FOR EASY REFERENCE

Model Colour

Serial Number Installation Date

Dealer's Name and Address

PROVISION FOR VENTILATION

POSITIONING

INSTALLATION

OVERALL DIMENSIONS

GENERAL INFORMATION

ENVIRONMENTAL WARNING
Waste packaging

Do not throw the packaging of your appliance into the dustbin,
but pick out the different materials (for instance foil, paperboard,
polystyrene) according to the local rules for rubbish elimination.

This appliance must only be used for the purpose of domestic
cooking.

895

600

B

729

60

22 or 40

B = adjustable height (89/149mm)

WHEN YOU CALL FOR SERVICE

When you call for service or order parts for your unit, be

sure to give:

1. MODEL

2. SERIAL NUMBER

3. COLOUR

4. PART NAME and/or description of problem

5. YOUR FUL L NAME, ADDRE SS, and HOME
TELEPHONE NUMBER and BUSINESS TELEPHONE
NUMBER IF APPROPRIATE.

Servicing shall be carried out only by authorised personnel.

SECTION FOR THE QUALIFIED TECHNICIAN

ATTENTION:

- Before using the appliance, do not forget to remove the
plastic protective film from parts of the appliance.

WARNING

Accessible parts will become hot when in use. To avoid
burns and scalds children should be kept away.

WARNING

In order to prevent accidental tipping of the appliance, for
example by a child climbing onto the open oven door, the
stabilizing means must be installed.

WARNING

This appliance is not intended for use by persons (including
children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge, unless
they have been given supervision or instruction concerning
use of the appliance by a person responsible for their safety.
Children should be supervised to ensure that they do not
play with the appliance.
Young children and infirm persons should not be left
unsupervised in the vicinity.

WARNING

Before you use the appliance for the first time, check that
the plastic films protecting some parts (fascia panel, parts
in stainless steel, etc.) have been removed.

WARNING:

A steam cleaner is not to be used cleaning this appliances.

WARNING
DO NOT USE OR STORE FLAMMABLE MATERIALS IN
THE APPLIANCE STORAGE DRAWER OR NEAR THIS
APPLIANCE.
DO NOT SPRAY AEROSOLS IN THE VICINITY OF THIS
APPLIANCE WHILE IT IS IN OPERATION.
WHERE THIS APPLIANCE IS INSTALLED IN MARINE
CRAFT OR IN CARAVAN, IT SHALL NOT BE USED AS
A SPACE HEATER
DO NOT MODIFY THIS APPLIANCE.

The room where the Cooker is installed should have
permanent ventilation as follows:
"Ventilation must be in accordance with AS5601/AG 601

- Gas Installations. In general, the appliance should have
adequate ventilation for complete combustion of gas,
proper flueing and to maintain temperature of immediate
surroundings within safe limits. "Do not install in a bed-sitting
room, a bathroom or shower room.
If there is another fuel burning appliance in the same room, a
higher level of ventilation will be required, you should consult

- "the safety requirements".
In addition to the above, during prolonged use, opening a
window in the same room is recommended. This will avoid
the build up of excessive moisture and condensation.

Important: Fix the chain located next to the gas connection
on both sides of the cooker to the wall to prevent the cooker
from tilting. Both chains must be securely fixed.
Make sure that the wall surface behind the Cooker is non-
combustable (will not catch fire).
Where a painted surface is adjacent, a fire retardent paint
surface is recommended. Wallpaper, wood, or fabric should
not be used behind or next to the cooker.

2

Clearances to combustible materials

"Any adjoining wall surface (side or rear) situated within
200mm of any hob burner must be a suitable non-combusti-
ble material from the edge for a height of 150mm for the
entire length of the cooker.
Any combustible construction above the cooker must be at
least 650mm above the maintop." Ensure that a power and
gas supply are nearby. The Cooker should be located
carefully so that the heat produced by it has plenty of space
to escape. The diagram below shows an ideal configuration.

Clearances to non-combustible materials

"If the cooker is being fitted next to cupboards or adjoing
wall surfaces, which are within 200mm from the edge of the
hob burner and of a suitable non-combustible material as
specified in AS5601, then ensure that a distance of at least
6cm is left between the edge of the cooker and the
non-combustible material. This gap is to allow plenty of
space for the heat produced by the cooker to escape on
each side of the cooker.

No part of any adjoining wall surface can be made of
combustible materials. The protection of combustible
materials required by Clause 5.12.1.1 of AS5601-2004 is
the fixing of 5 mm thick ceramic tiles to the surface or
attaching fire resistant material to the surface and covering
with sheet metal with a minimum thickness of 0.4 mm.

Note:
The cooker is fitted with 4 legs for an eventual alignment in
height with the furniture ( fig. 1 A ).

Fitting the splash guard

min. 650 mm

"0" mm "0" mm

min "60" mmmin "60" mm min "60" mm

non- combustible materials

non- combustible materials

min.100 mm

min. 650 mm

min. 400 mm

"0" mm "0" mm

min.10 mm

Fig. 1 A

OK

NO

1

2

3

Depending on the model.
Proceed as follows:

• Remove the packaging and the
protective film from the splash
guard.

•

Screw the splash guard onto
the rear of the appliance using
the

2 bolts.

To fix the cooker to the rear wall (anti-tilting chain/hose
restraining chain)

WARNING - For safety reasons and to prevent tipping of

the appliance, these stabilizing means must be installed.
The cooker is equipped with 2 chains fixed on each side at
the rear of the cooker near the top (see Fig. A). The chains
are fitted with "spring clips" which must be clipped to the
"screw eyes" provided with the cooker.
Install the "screw eyes" as follows:

1. Drill four 6mm holes (position 1 - 2 - 3 - 4) in the wall as
in Fig. A.

2. Insert part "R" into the holes then screw in the "screw
eyes" part "G" see Fig. B.
Note: If the part provided is not suitable for the wall
material please use an appropriate device to ensure
secure holding of the "screw eyes" to the wall.

3. Bring the cooker near the wall and clip the chains on the

"screw eyes" as in Fig. C.
IMPORTANT: If the cooker is moved for any reason (e.g.
maintenance) resulting in the cooker being unclipped from
the wall, the cooker must be re-clipped to the wall at the
completion of the task.
A chain should be fitted by the installer within 50mm of the
hos e connection point to prevent strain on the hose when
the cooker is pulled forward. The chain should restrict the
appliance movement to no more than 80% of the hose
length. After the chain is installed, check that there is no
strain on the hose or gas connections when the cooker is
pulled as far forward as the chain allows.

Fig. A

• Not permitted use with lids or
covers aftermarket

4

Gas installation must be made in accordance with AS5601;
Also refer to rangehood manufacturers recommendation.
Check gas presure, note the correct setting from the data
plate sealed inside the front appliance drawer *.

Stability bracket
WARNING: In order to prevent accidental tipping of the

appliance, for example a child climbing onto the open oven
door, the stabilising means must be installed.
Note: If the wall plug provided is not suitable for the wall
material please use an appropriate device to ensure secure
holding of the "screw" to the wall.

Installing the gas cooker:
(Flexible connection are NOT supplied with this appliance)

- An inlet manifold extension pipe must be fitted to the
appliance. Part supplied in the drawer of the appliance.

- Ensure that the pipe is connetted using the washer
provided and that the braket is screwed to the appliance
as shown in the diagram below.

- Fit the supplied pressure regulator (for Natural gas) using
the NG test piont adaptor and washer to the inlet manifold.
Ensure the arrow is pointing towards the appliance and
that pressure testpoint is accessible from the final
position.

- Push the cooker back and install the stabilizing chains.

- Connect the appliance inlet manifold to the consumer
piping outlet using only fixed piping. This final connection
is made when the product is pushed back into position by
access under the cooker.

The hose assembly

- Must comply with AS/NZS 1869 Class B or D,

- With 10 mm internal diameter and be kept as short as
possible (less than 1,2 m)

Fig. B Fig. C

GAS CONNECTION

- It must not be kinked

- It must not be in contact with hot surfaces.

IT IS RECOMMENDED THAT A SERVICE TAP AND UNION BE
FITTED ADJACENT TO THE APPLIANCE INLET TO
FACILITATE FUTURE SERVICING.

5 burner models: set the burner pressure to 1kPa for Natural
Gas and 2.75kPa for U-LPG with the wok burner operating a
full rate'. For commissioning of the appliance with the
regulator for Natural Gas, the test point pressure should be

1.00kPa with all burners operating on HIGH.
Apply a manometer to the test nipple and reset the regulator
if necessary. Do not forget to replace the test nipple screw
and to leave the instructions book with the user.

VERY IMPORTANT FOR THE INSTALLER

Do not attempt to turn or stress threaded elbow of the
manifold: you risk damage to this part of the gas appliance
which may void the manufacturers warranty.
Before Leaving – Check all connections for gas leaks.
DO NOT use a naked flame for detecting leaks. Ignite all
burners to ensure correct operation of gas valves, burners
and ignition. Turn gas taps to low flame position and
observe stability of the flame.
When satisfied with the cooker, please instruct the user on
the correct method of operation.
In case the appliance fails to operate correctly after all
checks have been carried out, refer to the authorised
service provider in your area.

GAS CONVERSION AND ADJUSTMENT

When used with natural gas all burners have been preset at
our factory and further adjustment should not be
necessary. Conversion kits to other gases are available
from the place of purchase. Do not attempt to fit the
conversion kit yourself. Conversion to U-LPG gas should
only be carried out by an authorized technician.

GAS ADJUSTEMENTS

- change the injectors

- adjust the minimum flow
‘When conver ting from Natural Gas to U-LPG ensure that
the NG regulator is removed and replaced with the Test
Point Assembly. A gas regulator suitable for a supply
pressure of 2.75kPa should be part of the gas tank supply
and should be adjusted with the wok burner operating at
maximum.

REPLACEMENT OF THE INJECTORS

When required to operate on other gas replace the
injectors in accordance with information referred to in chart
below.

A test point fitting must be
installed between the piping and
the appliance for the pressure to
be checked to ensure it is
operating for ULPG at 2.75 kPa.
Be aware that the appliance has
two gas inlets (L/R). Before
performing the leakage test
select which side will be the
connection point and cap and
pressure test the side that will not
be used.

A test point fitting must be
installed between the piping and
the appliance for the pressure to
be checked to ensure it is
operating for NATURAL GAS at 1
kPa.
Be aware that the appliance has
two gas inlets (L/R). Before
performing the leakage test select
which side will be the connection
point and cap and pressure test
the side that will not be used.

Pressure regulator for natural
gas

Pressure tst point for ULPG

Wall Fixing

Note:refer to page 15 for installation on a plinth.

The appliance must be installed by a suitably qualified
person in accordance with these instructions and with the
requirements of the Australian Wiring Rules AS/NZS 3000.
Fixed wired installations are to be provided with suitable
isolation means in accordance with the said rules.
Any plug socket installed for the purpose of connecting the
appliance to supply must be readily accessible when the
appliance is installed.
Before making the connection, make sure that:

1) the safety circuit-breaker and the electrical system are
able to withstand the load of the appliance
(see nameplate).

2) the power supply system has an earth connection in good
working order in accordance with the regulations in force;

IMPORTANT

The wires in the mains lead are coloured in accordance with
the following code:

GREEN & YELLOW..................................................... EARTH

BLUE ..................................................................... NEUTRAL

BROWN ......................................................................... LIVE

Electric power 1,5 mm

2

core cable (15 amp. Fuse required)
Should conform to local authority requirements.
Also refer to rangehood manufacturers recommendations.
This appliance is supplied with a plug & cord, simply plug
into a 3 pin household socket outlet witch is properly
earthed.
If he supply cord is damaged, it must be replaced by an
authorised service agent.

WARNING: THIS APPLIANCE MUST BE EARTHED.

The flexible mains lead and plug must not be in contact with
hot surfaces.

The correct adjustment is obtained when the flame has a
length of about 3 or 4 mm.
For butane/propane gas, the adjusting screw must be
screwed in thigt.
Make sure that the flame does not go out turning quickly
from the max. flow to the minimum flow .
Refit the knob again.

Adjustments, conversions and gas installations must only be
carried out by an authorised person.

After there placement of the injectors, replace also the label of
the type of gas.

SPECIAL NOTE

After installation or any servicing operation, always ensure that
the appliance is gas sound and that the components are now
operating correctly. Items removed during servicing should be
replaced in the reverse order to their removal.
In order to change the work-top injectors, it is necessary to act
as follows:

- remove the grids

- remove burners
and flame-spreaders.

MINIMUM FLOW ADJUSTMENT FOR HOB-TOP TAPS

In order to adjust the minimum flame setting proceed as
follows: switch the burner on, and set the knob at the
minimum position . Remove the knob from the tap.
The minimum adjusting screw «Z» is on the body of the gas
tap (fig. 2).

5

ELECTRICAL CONNECTION

TAB. 1

Jet mm ø

Gas Type

kPa

U-LPG 2.75

Natural

1.00 1.20

Burners

Semi-quick

Power MJ/h

7.1

0.90

Auxiliary

4.0

1.50

Quick

11.0

1.63

Triple Crown

12.7

0.73

Semi-quick

7.1

0.53

Auxiliary

3.7

0.95

Quick

11.7

1.00

Triple Crown

13.0

Regulator

NG Regulator

LP Test point
adaptor

- change the injector (see Fig. D) and replace it with another
one suitable for the new type of gas (see tab. 1)

Unscrew the adjusting screw in order to increase the flow
or screw it to decrease the flow.

Fig. D

Fig. 2

2nd SECTION FOR THE USER

WARNING:

Children should be kept away while the oven or grill is in use
since accessible parts become hot.

- Do not use oven base panel as a shelf, make use of the

oven shelves.

- To avoid splattering and smoke, position collecting tray

under the grill with some water in it.

- WARNING -

During use, the appliance becomes hot.
Care should be taken to avoid touching heating elements
inside the oven.

6

- Always turn pan handles to the side or to the back of the
hob. If they are left out into the room they can easily be hit
or reached by children, this knocking the pan off the hob.

- Don’t let children sit down or play with the oven door. Do
not use the drop down door as a stool to reach above
cabinets.

- Once your cooking is over make sure to close the main gas
supply.

WARNING

* This appliance is not intended for use by young children or

infirm persons without supervision.

* Young children should be supervised to ensure that they do

not play with the appliance.

- WARNING -

In order to prevent accidental tipping of the appliance, for
example by a child climbing onto the open oven door, the
stabilizing means must be installed.

Always use pans with a flat base diameter, which are well
balanced and stable in use, a pan which overhangs the
hotplate should not be used. Avoid using old, misshapen pans,
or pans which are unstable when placed on a flat surface. Do
not use “split pans” as they are inherently unstable.
To save gas, always position pans centrally over the burners
and adjust the flames so that they do not lick up the sides of
the pan and only the base is heated. Always put lids on
saucepans and boil only the amount of liquid you use. When
the liquid has boiled adjust the setting to maintain a simmer.
Do not light the burner until the pan is in position and turn off
the burner before removing the pan. In hard water areas,
descale kettles regularly. For safety, keep saucepan handles
turned to a safe position so they are out of reach of small
children and cannot be accidentally knocked.

To tunr the burner OFF, turn the control knob clockwise to the
OFF setting (marked with a dot )

BURNERS PANS
fl min. fl max

AUXILIARY 80 mm 160 mm
SEMI-RAPID 120 mm 200 mm
RAPIDE 200 mm 230 mm
TRIPLE CROWN 230 mm 260 mm

- 1 Minute Tour -

Be safe

Please read the rest of the instruction book which contains
important information to help you use the appliance safely
and efficiently.

Gas and Electricity on

Make sure that the gas supply is turned on and that the
appliance is plugged in and switched on. The ignitor needs
electricity.
In case there is no electric current, the burner can also be
lighted using a match.

It is recommended that pans suitable to the size of the burner
should be used as follows:

Automatic electric ignition

To turn on a burner, press the knob corresponding to the
selected burner and turn it anticlockwise to the maximum
position. Keeping the knob pressed, the electric automatic
ignition of the burner will be started up. In case there is not
electric current, the burner can also be lighted using a match.

The small flame indicates the ‘low position’.
Turn the knob to it after the contents of a pan have boiled.

The smaller burners are for smaller pans and simmering.
Make sure flames are under the pans. Using a lid will help the
contents boil more quickly.

WARNING

It is not recommended to press push button for ignition if all
the burners are not located in the proper positions. The burner
heads, burner skirts and pan supports are removable for
better cleaning: Always ensure that the burner skirts and
heads are replaced correctly so that the burners function
safely and correctly.
During the use of the appliance pay attention that water or any
liquid does not enter into the appliance through the holes of
the burners or around the rods of the valves or the push button
electronic lighter.
Water or juice will produce dangerous short-circuits and can
seriously damage the working of the Hotplate.

HOW TO USE YOUR ELECTRIC OVEN

MULTIFUNCTIONAL OVEN

The oven is fitted with:

• a lower heating element;

• an upper heating element;

• a circular heating element surrounding the fan.
N.B.: Always set the temperature on the thermostat knob

before selecting any of the functions.

- Before cooking in the first time we reccommend that the
oven should be operated at 200° C for 30 minutes to
remove any manufacturing greases and odours.

- Do not place items or pan directly on to the oven botton.

- Foil should only be used to cover food and not oven shelves
or party of the oven. When used improperly will obstruct the
air circulation causing problems in cooking and/or harmful
accidents.