ARTHUR MARTIN ASL5341LA User Manual
ASL5341LA
EN
FR
DE
Dishwasher User Manual 2
Lave-vaisselle Notice d'utilisation 20
Geschirrspüler Benutzerinformation 41
2
CONTENTS
Safety information 2
Safety instructions 3
Product description 5
Control panel 6
Programmes 6
Settings 7
Options 10
Before first use 10
Daily use 11
Hints and tips 13
Care and cleaning 14
Troubleshooting 16
Technical information 19
Subject to change without notice.
SAFETY INFORMATION
Before the installation and use of the appliance, carefully read
the supplied instructions. The manufacturer is not responsible
for any injuries or damages that are the result of incorrect
installation or usage. Always keep the instructions in a safe
and accessible location for future reference.
Children and vulnerable people safety
• This appliance can be used by children aged 8 years and
above and by persons with reduced capabilities provided
that they have been given instruction and/or supervision
regarding the safe use of the appliance and understand the
potential hazards involved.
• Do not let children play with the appliance.
• Keep detergents away from children.
• Keep children and pets away from the appliance door when
it is open.
Children shall not carry out cleaning and user maintenance
•
of the appliance without supervision.
General Safety
This appliance is intended to be used in household and
•
similar applications such as:
farm houses; staff kitchen areas in shops, offices and
–
other working environments;
by clients in hotels, motels, bed & breakfast and other
–
residential type environments.
• Do not change the specification of this appliance.
• The operating water pressure (minimum and maximum)
must be between 0.5 (0.05) / 8 (0.8) bar (MPa)
• Obey the maximum number of 13 place settings.
• If the supply cord is damaged, it must be replaced by the
manufacturer, its Authorised Service Centre or similarly
qualified persons in order to avoid a hazard.
• Put knives and cutlery with sharp points in the cutlery basket
with the points down or in a horizontal position.
• Do not keep the appliance door open without supervision to
prevent to fall on it.
• Before any maintenance operation, deactivate the appliance
and disconnect the mains plug from the socket.
• Do not use high pressure water sprays and/or steam to
clean the appliance.
• The ventilation openings in the base (if applicable) must not
be obstructed by a carpet.
• The appliance is to be connected to the water mains using
the new supplied hose-sets. Old hose sets must not be
reused.
3
SAFETY INSTRUCTIONS
Installation
• Remove all the packaging.
• Do not install or use a damaged
appliance.
• Do not install or use the appliance where
the temperature is less than 0 °C.
• Follow the installation instruction
supplied with the appliance.
• Make sure that the appliance is installed
below and adjacent to safe structures.
Electrical connection
WARNING! Risk of fire and
electrical shock.
• The appliance must be earthed.
• Make sure that the electrical information
on the rating plate agrees with the
power supply. If not, contact an
electrician.
• Always use a correctly installed
shockproof socket.
• Do not use multi-plug adapters and
extension cables.
• Make sure not to cause damage to the
mains plug and to the mains cable.
Should the mains cable need to be
replaced, this must be carried out by our
Authorised Service Centre.
• Connect the mains plug to the mains
socket only at the end of the installation.
Make sure that there is access to the
mains plug after the installation.
• Do not pull the mains cable to
disconnect the appliance. Always pull
the mains plug.
• This appliance complies with the E.E.C.
Directives.
• Only for UK and Ireland. The appliance
has a 13 amp mains plug. If it is
4
necessary to change the fuse in the
mains plug, use fuse: 13 amp ASTA (BS
1362).
Water connection
• Do not cause damage to the water
hoses.
• Before connection to new pipes, pipes
not used for a long time, where repair
work has been carried out or new
devices fitted (water meters, etc.), let the
water flow until it is clean and clear.
• Ensure that there are no visible water
leaks during and after the first use of the
appliance.
• The water inlet hose has a safety valve
and a sheath with an inner mains cable.
WARNING! Dangerous
voltage.
• If the water inlet hose is damaged,
immediately close the water tap and
disconnect the mains plug from the
mains socket. Contact the Authorised
Service Centre to replace the water inlet
hose.
Use
• Do not sit or stand on the open door.
• Dishwasher detergents are dangerous.
Obey the safety instructions on the
detergent packaging.
• Do not drink and play with the water in
the appliance.
• Do not remove the dishes from the
appliance until the programme is
completed. There can be detergent on
the dishes.
• The appliance can release hot steam if
you open the door while a programme
operates.
• Do not put flammable products or items
that are wet with flammable products in,
near or on the appliance.
Service
• Contact the Authorised Service Centre
to repair the appliance. We recommend
only the use of original spare parts.
• When you contact the Authorised
Service Centre, ensure that you have the
following information that is available on
the rating plate.
Model :
PNC :
Serial Number :
Disposal
WARNING! Risk of injury or
suffocation.
• Disconnect the appliance from the mains
supply.
• Cut off the mains cable and discard it.
• Remove the door catch to prevent
children and pets to get closed in the
appliance.
PRODUCT DESCRIPTION
4
3
7
9
8
10
56
11
1
2
5
Upper spray arm
1
Lower spray arm
2
Filters
3
Rating plate
4
Salt container
5
Air vent
6
Beam-on-Floor
The Beam-on-Floor is a light that is
displayed on the floor below the appliance
door.
• When the programme starts, a red light
comes on and stays on for the duration
of the programme.
• When the programme is completed, a
green light comes on.
Rinse aid dispenser
7
Detergent dispenser
8
Cutlery basket
9
Lower basket
10
Upper basket
11
• When the appliance has a malfunction,
the red light flashes.
The Beam-on-Floor goes off
when the appliance is
deactivated.
1 2
4
3
5
6
CONTROL PANEL
On/off button
1
Display
2
Delay button
3
Indicators
Indicator Description
XtraDry indicator.
Rinse aid indicator. It is always off while the programme operates.
Salt indicator. It is always off while the programme operates.
PROGRAMMES
Programme Degree of soil
Type of load
1)
2)
3)
4)
• Normal soil
• Crockery and
cutlery
• All
• Crockery, cutlery, pots and
pans
• Heavy soil
• Crockery, cutlery, pots and
pans
• Fresh soil
• Crockery and
cutlery
Programme buttons
4
Indicators
5
Programme phases Options
• Prewash
• Wash 50 °C
• Rinses
• Dry
• Prewash
• Wash from 45 °C to 70
°C
• Rinses
• Dry
• Prewash
• Wash 70 °C
• Rinses
• Dry
• Wash 60 °C or 65 °C
• Rinses
• XtraDry
• XtraDry
• XtraDry
• XtraDry
7
Programme Degree of soil
Type of load
5)
1)
With this programme you have the most efficient use of water and energy consumption for crockery and cutlery
with normal soil. (This is the standard programme for test institutes).
2)
The appliance senses the degree of soil and the quantity of items in the baskets . It automatically adjusts the tem-
perature and the quantity of water, the energy consumption and the programme duration.
3)
This programme has a high temperature rinsing phase for better hygiene results. During the rinsing phase, the
temperature stays at 70 °C for at least 10 minutes.
4)
With this programme you can wash a load with fresh soil. It gives good washing results in a short time.
5)
With this programme you can quickly rinse dishes to prevent remains of food to bond on dishes and odours to
form in the appliance. Do not use detergent with this programme.
• All • Prewash
Programme phases Options
Consumption values
Programme
1)
The pressure and the temperature of the water, the variations of the mains supply, the options and the quantity of
dishes can change the values.
1)
Water
(l)
11 1.050 195
7 - 12 0.6 - 1.4 40 - 150
13 - 15 1.5 - 1.6 150 - 170
9 0.8 30
4 0.1 14
Energy
(kWh)
Duration
(min)
Information for test institutes
For all the necessary information for test
performance, send an email to:
info.test@dishwasher-production.com
SETTINGS
Programme selection mode and user mode
When the appliance is in programme
selection mode it is possible to set a
programme and to enter the user mode.
In user mode, the following settings
can be changed:
Write down the product number (PNC) that
is on the rating plate.
• The level of the water softener according
to the water hardness.
• The activation or the deactivation of the
acoustic signal for end of programme.
• The activation or deactivation of the rinse
aid empty notification.
These settings will be saved until you
change them again.
8
How to set the programme selection mode
The appliance is in programme selection
mode when the programme indicator
is flashing and the display shows the
programme duration.
When you activate the appliance, usually it
is in programme selection mode. However,
if this does not happen, you can set the
programme selection mode in the following
way:
Press and hold simultaneously and
until the appliance is in programme
selection mode.
The water softener
The water softener removes minerals from
the water supply, which would have a
detrimental effect on the washing results
and on the appliance.
The higher the content of these minerals,
the harder your water is. Water hardness is
measured in equivalent scales.
The water softener should be adjusted
according to the hardness of the water in
your area. Your local water authority can
advise you on the hardness of the water in
your area. It is important to set the right
level of the water softener to assure good
washing results.
Water hardness
German de-
grees (°dH)
47 - 50 84 - 90 8.4 - 9.0 58 - 63 10
43 - 46 76 - 83 7.6 - 8.3 53 - 57 9
37 - 42 65 - 75 6.5 - 7.5 46 - 52 8
29 - 36 51 - 64 5.1 - 6.4 36 - 45 7
23 - 28 40 - 50 4.0 - 5.0 28 - 35 6
19 - 22 33 - 39 3.3 - 3.9 23 - 27
15 - 18 26 - 32 2.6 - 3.2 18 - 22 4
11 - 14 19 - 25 1.9 - 2.5 13 - 17 3
4 - 10 7 - 18 0.7 - 1.8 5 - 12 2
<4 <7 <0.7 < 5
1)
Factory setting.
2)
Do not use salt at this level.
French de-
grees (°fH)
mmol/l Clarke de-
grees
Water softener
level
1)
5
2)
1
Whether you use a standard detergent
or multi-tabs (with or without salt), set
the proper water hardness level to
keep the salt refill indicator active.
Multi-tabs containing salt are not
effective enough to soften hard
water.
How to set the water softener level
The appliance must be in programme
selection mode.
1. To enter the user mode, press and hold
simultaneously
and until
9
the indicators , and
start to flash and the display is blank.
2. Press .
• The indicators and go
off.
• The indicator continues to flash.
• The display shows the current
setting: e.g. = level 5.
3. Press
setting.
4. Press the on/off button to confirm the
setting.
again and again to change the
The rinse aid empty notification
The rinse aid helps to dry the dishes
without streaks and stains.
The rinse aid is automatically released
during the hot rinse phase.
When rinse aid chamber is empty, the rinse
aid indicator is turned on notifying to refill
rinse aid. If you are using multi-tabs
containing rinse aid and you are satisfied
with the drying result, you can deactivate
the notification for refilling rinse aid.
However, we recommend that you always
use rinse aid for best drying performance.
If you use standard detergent or multitablets without rinse aid, activate the
notification to keep the rinse aid refill
indicator active.
How to deactivate the rinse aid empty notification
The appliance must be in programme
selection mode.
1. To enter the user mode, press and hold
simultaneously
the indicators , and
start to flash and the display is blank.
2. Press
• The indicators
off.
.
and until
and go
• The indicator continues to
flash.
• The display shows the current
setting.
– = rinse aid empty notification
activated.
– = rinse aid empty
notification deactivated.
3. Press
4. Press the on/off button to confirm the
setting.
to change the setting.
Acoustic signals
Acoustic signals sound when a malfunction
of the appliance occurs. It is not possible to
deactivate these acoustic signals.
There is also an acoustic signal that sounds
when the programme is completed. By
default this acoustic signal is deactivated
but it is possible to activate it.
How to activate the acoustic signal for the end of programme
The appliance must be in programme
selection mode.
1. To enter the user mode, press and hold
simultaneously
the indicators
start to flash and the display is blank.
2. Press .
• The indicators
• The indicator continues to
flash.
• The display shows the current
setting:
= Acoustic signal off.
–
– = Acoustic signal on.
3. Press to change the setting.
4. Press the on/off button to confirm the
setting.
and until
, and
and go off.
10
OPTIONS
Desired options must be
activated every time before you
start a programme.
It is not possible to activate or
deactivate options while a
programme is running.
Not all options are compatible
with each other. If you have
selected non compatible
options, the appliance will
automatically deactivate one or
more of them. Only the
indicators of the options still
active will stay on.
XtraDry
Activate this option when you want to boost
the drying performance. With the use of this
BEFORE FIRST USE
1. Make sure that the current level of
the water softener agrees with the
hardness of the water supply. If not,
adjust the level of the water
softener.
2. Fill the salt container.
3. Fill the rinse aid dispenser.
4. Open the water tap.
5. Start a programme to remove any
processing residuals that can still be
inside the appliance. Do not use
detergent and do not load the baskets.
When you start a programme, the
appliance can take up to 5 minutes to
recharge the resin in the water softener. It
seems that the appliance is not working.
The washing phase starts only after this
procedure is completed. The procedure will
be repeated periodically.
The salt container
CAUTION! Only use salt
specifically designed for
dishwashers.
option, the duration of some programmes,
water consumption and the last rinse
temperature can be affected.
The option XtraDry is not a permanent
option and must be selected at every cycle.
How to activate XtraDry
Press simultaneously
indicator
If the option is not applicable to the
programme, the related indicator does not
come on or it flashes quickly for a few
seconds and then goes off.
The display shows the updated programme
duration.
The salt is used to recharge the resin in the
water softener and to assure good washing
results in the daily use.
comes on.
and . The
How to fill the salt container
1. Turn the cap of the salt container
counterclockwise and remove it.
2. Put 1 litre of water in the salt container
(Only for the first time).
3. Fill the salt container with dishwasher
salt.
4.
Remove the salt around the opening of
the salt container.
5. Turn the cap of the salt container
A
B
D
C
M
A
X
1
2
3
4
+
-
A
B
D
C
30
20
A BD
C
clockwise to close the salt container.
CAUTION! Water and salt can
come out of the salt container
when you fill it. After you fill the
salt container, immediately start
a programme to prevent
corrosion.
How to fill the rinse aid dispenser
CAUTION! Only use rinse aid
specifically designed for
dishwashers.
1.
Press the release button (D) to open the
lid (C).
2.
Pour the rinse aid in the dispenser (A)
until the liquid reaches the fill level
'max'.
3.
Remove the spilled rinse aid with an
absorbent cloth to prevent too much
foam.
4.
Close the lid. Make sure that the release
button locks into position.
You can turn the selector of the
released quantity (B) between
position 1 (lowest quantity) and
position 4 or 6 (highest quantity).
11
DAILY USE
1. Open the water tap.
2. Press the on/off button to activate the
appliance.
Make sure that the appliance is in
programme selection mode.
• If the salt indicator is on, fill the salt
container.
• If the rinse aid indicator is on, fill the
rinse aid dispenser.
3. Load the baskets.
4. Add the detergent.
5. Set and start the correct programme for
the type of load and the degree of soil.
Using the detergent
20
30
B
A D
C
12
1. Press the release button (B) to open the
lid (C).
2.
Put the detergent, in powder or tablets,
in the compartment (A).
3.
If the programme has a prewash phase,
put a small quantity of detergent in the
compartment (D).
4.
Close the lid. Make sure that the release
button locks into position.
Setting and starting a programme
The Auto off function
This function decreases energy
consumption by deactivating automatically
the appliance when it is not operating.
The function comes into operation:
• 5 minutes after the completion of the
programme.
• After 5 minutes if the programme has
not started.
Starting a programme
1. Keep the appliance door ajar.
2. Press the on/off button to activate the
appliance. Make sure that the appliance
is in programme selection mode.
3. Press the button related to the
programme you want to start.
The display shows the programme
duration.
4. Set the applicable options.
5. Close the appliance door to start the
programme.
Starting a programme with delay start
1. Set a programme.
2. Press again and again until the
display shows the delay time you want
to set (from 1 to 24 hours).
The delay indicator comes on.
3. Close the appliance door to start the
countdown.
While a countdown is running it is possible
to increase the delay time but not to
change the selection of the programme and
options.
When the countdown is completed, the
programme starts.
Opening the door while the appliance operates
If you open the door while a programme is
running, the appliance stops. It may affect
the energy consumption and the
programme duration. When you close the
door, the appliance continues from the
point of interruption.
If the door is opened for more
than 30 seconds during the
drying phase, the running
programme will end.
Cancelling the delay start while the countdown operates
When you cancel the delay start you have
to set the programme and options again.
Press and hold simultaneously and
until the appliance is in programme
selection mode.
Cancelling the programme
Press and hold simultaneously and
until the appliance is in programme
selection mode.
13
Make sure that there is detergent in the
detergent dispenser before you start a new
programme.
End of the programme
When the programme is completed the
display shows 0:00 .
HINTS AND TIPS
General
The following hints will ensure optimal
cleaning and drying results in daily use and
also help to protect the environment.
• Remove larger residues of food from the
dishes into the waste bin.
• Do not pre-rinse dishes by hand. When
needed, use the prewash programme (if
available) or select a programme with a
prewash phase.
• Always use the whole space of the
baskets.
• When loading the appliance, make sure
that the dishes can be completely
reached and washed by the water
released from the spray arm nozzles.
Make sure that items do not touch or
cover each other.
• You can use dishwasher detergent, rinse
aid and salt separately or you can use
the multi-tablets (e.g. ''3in1'', ''4in1'',
''All in 1''). Follow the instructions written
on the packaging.
• Select the programme according to the
type of load and degree of soil. With the
ECO programme you have the most
efficient use of water and energy
consumption for crockery and cutlery
with normal soil.
Using salt, rinse aid and detergent
• Only use salt, rinse aid and detergent for
dishwasher. Other products can cause
damage to the appliance.
• In areas with hard and very hard water
we recommend to use plain dishwasher
detergent (powder, gel, tablets
containing no additional agents), rinse
1. Press the on/off button or wait for the
Auto off function to automatically
deactivate the appliance.
2. Close the water tap.
aid and salt separately for optimal
cleaning and drying results.
• At least once a month run the appliance
with the use of appliance cleaner which
is particularly suitable for this purpose.
• Detergent tablets do not fully dissolve
with short programmes. To prevent
detergent residues on the tableware, we
recommend that you use the tablets with
long programmes.
• Do not use more than the correct
quantity of detergent. Refer to the
instructions on the detergent packaging.
What to do if you want to stop using multi-tablets
Before you start to use separately
detergent, salt and rinse aid do the
following procedure.
1.
Set the highest level of the water
softener.
2.
Make sure that the salt and rinse aid
containers are full.
3.
Start the shortest programme with a
rinsing phase. Do not add detergent
and do not load the baskets.
4. When the programme is completed,
adjust the water softener according to
the water hardness in your area.
5. Adjust the released quantity of rinse aid.
6. Activate the rinse aid empty notification.
Loading the baskets
• Only use the appliance to wash items
that are dishwasher-safe.
• Do not put in the appliance items made
of wood, horn, aluminium, pewter and
copper.
C
B
A
14
• Do not put in the appliance items that
can absorb water (sponges, household
cloths).
• Remove remaining food from the items.
• Make soft the remaining burned food on
the items.
• Put hollow items (cups, glasses and
pans) with the opening down.
• Make sure that cutlery and dishes do not
bond together. Mix spoons with other
cutlery.
• Make sure that glasses do not touch
other glasses.
• Put small items in the cutlery basket.
• Put light items in the upper basket.
Make sure that the items do not move.
• Make sure that the spray arm can move
freely before you start a programme.
Before starting a programme
Make sure that:
• The filters are clean and correctly
installed.
CARE AND CLEANING
WARNING! Before
maintenance, deactivate the
appliance and disconnect the
mains plug from the main
socket.
• The cap of the salt container is tight.
• The spray arms are not clogged.
• There is dishwasher salt and rinse aid
(unless you use multi- tablets).
• The position of the items in the baskets
is correct.
• The programme is applicable for the
type of load and for the degree of soil.
• The correct quantity of detergent is
used.
Unloading the baskets
1. Let the tableware cool down before you
remove it from the appliance. Hot items
can be easily damaged.
2.
First remove items from the lower
basket, then from the upper basket.
At the end of the program water
can still remain on the sides and
on the door of the appliance.
Dirty filters and clogged spray
arms decrease the washing
results. Make a check regularly
and, if necessary, clean them.
Cleaning the filters
The filter system is made of 3 parts.
1.
Turn the filter (B) counterclockwise and
remove it.
2.
Remove the filter (C) out of filter (B).
3.
Remove the flat filter (A).
7. Reassemble the filters (B) and (C).
8.
Put back the filter (B) in the flat filter (A).
Turn it clockwise until it locks.
15
4. Wash the filters.
5. Make sure that there are no residues of
food or soil in or around the edge of the
sump.
6. Put back in place the flat filter (A). Make
sure that it is correctly positioned under
the 2 guides.
CAUTION! An incorrect position
of the filters can cause bad
washing results and damage to
the appliance.
Cleaning the spray arms
Do not remove the spray arms. If the holes
in the spray arms are clogged, remove
remaining parts of soil with a thin pointed
object.
External cleaning
• Clean the appliance with a moist soft
cloth.
• Only use neutral detergents.
• Do not use abrasive products, abrasive
cleaning pads or solvents.
Internal cleaning
• Carefully clean the appliance, including
the rubber gasket of the door, with a soft
damp cloth.
16
• If you regularly use short duration
programmes, these can leave deposits
of grease and limescale inside the
appliance. To prevent this, we
use monthly a specific cleaning product
for dishwashers. Follow carefully the
instructions on the packaging of the
product.
recommend to run long duration
programmes at least 2 times per month.
• To maintain the performance of your
appliance at its best, we recommend to
TROUBLESHOOTING
If the appliance does not start or it stops
during operation. Before you contact an
Authorised Service Centre, check if you can
solve the problem by yourself with the help
of the information in the table.
WARNING! Repairs not
properly done may result in
serious risk to the safety of the
user. Any repairs must be
performed by qualified
personnel.
Problem and alarm code Possible cause and solution
You cannot activate the appliance.
The program does not start. • Make sure that the appliance door is closed.
The appliance does not fill
with water.
The display shows .
The appliance does not drain
the water.
The display shows .
The anti-flood device is on.
The display shows .
• Make sure that the mains plug is connected to the mains
socket.
• Make sure that there is no damaged fuse in the fuse box.
• If the delay start is set, cancel the setting or wait for the end
of the countdown.
• The appliance has started the procedure to recharge the
resin inside the water softener. The duration of the procedure is approximately 5 minutes.
• Make sure that the water tap is open.
• Make sure that the pressure of the water supply is not too
low. For this information, contact your local water authority.
• Make sure that the water tap is not clogged.
• Make sure that the filter in the inlet hose is not clogged.
• Make sure that the inlet hose has no kinks or bends.
• Make sure that the sink spigot is not clogged.
• Make sure that the filter in the outlet hose is not clogged.
• Make sure that the interior filter system is not clogged.
• Make sure that the drain hose has no kinks or bends.
• Close the water tap and contact an Authorised Service Centre.
With some problems, the display
shows an alarm code.
The majority of problems that can
occur can be solved without the need
to contact an Authorised Service
Centre.
Problem and alarm code Possible cause and solution
The appliance stops and
starts more times during operation.
The program lasts too long. • If the delayed start option is set, cancel the delay setting or
The remaining time in the display increases and skips
nearly to the end of program
time.
Small leak from the appliance
door.
The appliance door is difficult
to close.
Rattling/knocking sounds
from inside the appliance.
The appliance trips the circuit-beaker.
• It is normal. It provides optimal cleaning results and energy
savings.
wait for the end of the countdown.
• This is not a defect. The appliance is working correctly.
• The appliance is not levelled. Loosen or tighten the adjustable feet (if applicable).
• The appliance door is not centred on the tub. Adjust the rear
foot (if applicable).
• The appliance is not levelled. Loosen or tighten the adjustable feet (if applicable).
• Parts of the tableware are protruding from the baskets.
• The tableware is not properly arranged in the baskets. Refer
to basket loading leaflet.
• Make sure that the spray arms can rotate freely.
• The amperage is insufficient to supply simultaneously all the
appliances in use. Check the socket amperage and the capacity of the meter or turn off one of the appliances in use.
• Internal electrical fault of the appliance. Contact an Authorised Service Centre.
17
Refer to "Before first use",
"Daily use", or "Hints and
tips" for other possible causes.
Once you have checked the appliance,
problem occurs again, contact an
Authorised Service Centre.
For alarm codes not described in the table,
contact an Authorised Service Centre.
deactivate and activate the appliance. If the
The washing and drying results are not satisfactory
Problem Possible cause and solution
Poor washing results. • Refer to "Daily use", "Hints and tips" and basket load-
ing leaflet.
• Use more intensive washing programmes.
• Clean spray arm jets and filter. Refer to "Care and
Cleaning".
18
Problem Possible cause and solution
Poor drying results. • Tableware has been left for too long inside a closed appli-
ance.
• There is no rinse aid or the dosage of rinse aid is not
enough. Set the rinse aid dispenser to a higher level.
• Plastic items may need to be towel dried.
• For the best drying performance activate the option XtraDry.
• We recommend to always use rinse aid, even in combination with multi-tablets.
There are whitish streaks or
bluish layers on glasses and
dishes.
There are stains and dry water
drops on glasses and dishes.
The dishes are wet. • For the best drying performance activate the option Xtra-
The interior of the appliance is
wet.
Unusual foam during washing. • Use the detergent for dishwashers only.
Traces of rust on cutlery. • There is too much salt in the water used for washing. Re-
There are residues of detergent
in the dispenser at the end of
the programme.
Odours inside the appliance. • Refer to "Internal cleaning".
• The release quantity of rinse aid is too much. Adjust the
rinse aid level to a lower level.
• The quantity of detergent is too much.
• The released quantity of rinse aid is not sufficient. Adjust
the rinse aid level to a higher level.
• The quality of the rinse aid can be the cause.
Dry.
• The programme does not have a drying phase or has a
drying phase with low temperature.
• The rinse aid dispenser is empty.
• The quality of the rinse aid can be the cause.
• The quality of the multi-tablets can be the cause. Try a different brand or activate the rinse aid dispenser and use
rinse aid and multi-tablets together.
• Keep the dishwasher door ajar for some time before removing tableware.
• This is not a defect of the appliance. it is caused by the
humidity in the air that condenses on the walls.
• There is a leak in the rinse aid dispenser. Contact an Authorised Service Centre.
fer to "The water softener".
• Silver and stainless steel cutlery were placed together.
Avoid to put silver and stainless steel items close together.
• The detergent tablet got stuck in the dispenser and therefore was not completely washed away by water.
• Water cannot wash away the detergent from the dispenser. Make sure that the spray arm is not blocked or clogged.
• Make sure that items in the baskets do not impede the lid
of the detergent dispenser from opening.
Problem Possible cause and solution
Limescale deposits on the tableware, on the tub and on the
inside of the door.
Dull, discoloured or chipped tableware.
• The level of salt is low, check the refill indicator.
• The cap of the salt container is loose.
• Your tap water is hard. Refer to "The water softener".
• Even using multi-functional tabs use salt and set regeneration of the water softener. Refer to "The water soften-
er".
• If lime scale deposits still remain, clean the appliance with
appliance cleaners which are particularly suitable for this
purpose.
• Try different detergent.
• Contact the detergent manufacturer.
• Make sure that only dishwasher-safe items are washed in
the appliance.
• Load and unload the basket carefully. Refer to basket
loading leaflet.
• Place delicate items in the upper basket.
Refer to "Before first use",
"Daily use" or "Hints and
tips" for other possible causes.
TECHNICAL INFORMATION
19
Dimensions Width / height / depth (mm) 596 / 818 - 898 / 555
Electrical connection
Water supply pressure Min. / max. bar (MPa) 0.5 (0.05) / 8 (0.8)
Water supply
Capacity Place settings 13
Power consumption Left-on mode (W) 5.0
Power consumption Off-mode (W) 0.10
1)
Refer to the rating plate for other values.
2)
If the hot water comes from alternative source of energy, (e.g. solar panels, aeolian energy), use the hot water
supply to decrease energy consumption.
1)
Voltage (V) 220 - 240
Frequency (Hz) 50
Cold water or hot water
2)
max 60 °C
ENVIRONMENTAL CONCERNS
Recycle the materials with the symbol .
Put the packaging in applicable containers
to recycle it. Help protect the environment
and human health and to recycle waste of
electrical and electronic appliances. Do not
dispose appliances marked with the symbol
with the household waste. Return the
product to your local recycling facility or
contact your municipal office.
20
TABLE DES MATIÈRES
Informations de sécurité 20
Consignes de sécurité 21
Description de l'appareil 23
Bandeau de commande 24
Programmes 24
Réglages 26
Options 28
Avant la première utilisation 29
Utilisation quotidienne 30
Conseils 32
Entretien et nettoyage 33
En cas d'anomalie de fonctionnement 35
Caractéristiques techniques 39
Sous réserve de modifications.
INFORMATIONS DE SÉCURITÉ
Avant d'installer et d'utiliser cet appareil, lisez soigneusement
les instructions fournies. Le fabricant ne pourra être tenu pour
responsable des blessures et dégâts résultant d'une mauvaise
installation ou utilisation. Conservez toujours les instructions
dans un lieu sûr et accessible pour vous y référer
ultérieurement.
Sécurité des enfants et des personnes vulnérables
• Cet appareil peut être utilisé par des enfants de plus de
8 ans et par des personnes dont les capacités sont réduites,
à condition qu'ils soient surveillés ou qu'ils aient reçu des
instructions concernant l'utilisation sécurisée de l'appareil et
qu'ils comprennent les risques encourus.
• Ne laissez pas les enfants jouer avec l'appareil.
• Ne laissez pas les détergents à la portée des enfants.
Tenez les enfants et les animaux éloignés de la porte de
•
l'appareil lorsque celle-ci est ouverte.
Les enfants ne doivent pas nettoyer ni entreprendre une
•
opération de maintenance sur l'appareil sans surveillance.
Sécurité générale
Cet appareil est conçu uniquement pour un usage
•
domestique et des situations telles que :
bâtiments de ferme, cuisines réservées aux employés
–
dans les magasins, bureaux et autres lieux de travail ;
Loading...