How it Works
Arrow Storage Products
Loading...
VT1231
User Manual
48 pgs1.41 Mb0

Arrow Storage Products 697.68888, VT1231, 697.68887, VT1210, Arrow Storage Building User Manual

...
Download
Page 1
Owner's ManOwner's Man
Owner's Man
Owner's ManOwner's Man
BW1
ual & ual &
ual &
ual & ual &
AssembAssemb
Assemb
AssembAssemb
ll
y Instry Instr
l
y Instr
ll
y Instry Instr
uctionsuctions
uctions
uctionsuctions
Model No.Model No.
Model No.
Model No.Model No.
VT1210VT1210
VT1210
VT1210VT1210 VT1231VT1231
VT1231
VT1231VT1231
VT1217VT1217
VT1217
VT1217VT1217
697.68887 697.68887
697.68887
697.68887 697.68887
VT1224VT1224
VT1224
VT1224VT1224
697.68888 697.68888
697.68888
697.68888 697.68888
CAUTION: SOME PARTS HAVE SHARP EDGES. CARECAUTION: SOME PARTS HAVE SHARP EDGES. CARE
CAUTION: SOME PARTS HAVE SHARP EDGES. CARE
CAUTION: SOME PARTS HAVE SHARP EDGES. CARECAUTION: SOME PARTS HAVE SHARP EDGES. CARE MUST BE TAKEN WHEN HANDLING THE VARIOUS PIECESMUST BE TAKEN WHEN HANDLING THE VARIOUS PIECES
MUST BE TAKEN WHEN HANDLING THE VARIOUS PIECES
MUST BE TAKEN WHEN HANDLING THE VARIOUS PIECESMUST BE TAKEN WHEN HANDLING THE VARIOUS PIECES TO AVOID A MISHAP. FOR SAFETY SAKE, PLEASE READTO AVOID A MISHAP. FOR SAFETY SAKE, PLEASE READ
704880801
BUILDING DIMENSIONSBUILDING DIMENSIONS
BUILDING DIMENSIONS
BUILDING DIMENSIONSBUILDING DIMENSIONS
*Approx. Foundation Storage Area (Roof Edge to Roof Edge) (Wall to Wall) *Approx. Foundation Storage Area (Roof Edge to Roof Edge) (Wall to Wall)
*Approx. Foundation Storage Area (Roof Edge to Roof Edge) (Wall to Wall)
*Approx. Foundation Storage Area (Roof Edge to Roof Edge) (Wall to Wall) *Approx. Foundation Storage Area (Roof Edge to Roof Edge) (Wall to Wall)
Size Size Sq. Ft. Cu. Ft. Width Depth Height Width Depth Height Size Size Sq. Ft. Cu. Ft. Width Depth Height Width Depth Height
Size Size Sq. Ft. Cu. Ft. Width Depth Height Width Depth Height
Size Size Sq. Ft. Cu. Ft. Width Depth Height Width Depth Height Size Size Sq. Ft. Cu. Ft. Width Depth Height Width Depth Height
12' x 10' 141 1/8" x 111 3/4" 110 801 146 1/8" 117" 103 1/4" 141 1/8" 111 3/4" 102" 12' x 17' 141 1/8" x 198" 194 1419 146 1/8" 203 1/4" 103 1/4" 141 1/8" 198" 102" 12' x 24' 141 1/8" x 284 1/4" 278 2037 146 1/8" 289 1/2" 103 1/4" 141 1/8" 284 1/4" 102" 12' x 31' 141 1/8" x 370 1/2" 362 2655 146 1/8" 375 3/4" 103 1/4" 141 1/8" 370 1/2" 102"
3,7m x 3,1m 3,58m x 2,84m 10,2m 22,7m 3,71m 2,97m 2,62m 3,58m 2,84m 2,59m 3,7m x 5,2m 3,58m x 5,03m 18,0m 40,2m 3,71m 5,16m 2,62m 3,58m 5,03m 2,59m 3,7m x 7,3m 3,58m x 7,22m 25,8m 57,7m 3,71m 7,35m 2,62m 3,58m 7,22m 2,59m 3,7m x 9,5m 3,58m x 9,41m 33,6m 75,2m 3,71m 9,54m 2,62m 3,58m 9,41m 2,59m
* Size rounded off to the nearest foot
Exterior Dimensions Interior Dimensions Exterior Dimensions Interior Dimensions
Exterior Dimensions Interior Dimensions
Exterior Dimensions Interior Dimensions Exterior Dimensions Interior Dimensions
2 2
2 2
3 3
3 3
TO AVOID A MISHAP. FOR SAFETY SAKE, PLEASE READTO AVOID A MISHAP. FOR SAFETY SAKE, PLEASE READ SAFETY INFORMATION PROVIDED IN THIS MANUALSAFETY INFORMATION PROVIDED IN THIS MANUAL
SAFETY INFORMATION PROVIDED IN THIS MANUAL
SAFETY INFORMATION PROVIDED IN THIS MANUALSAFETY INFORMATION PROVIDED IN THIS MANUAL BEFORE BEGINNING CONSTRUCTION. WEAR GLOVESBEFORE BEGINNING CONSTRUCTION. WEAR GLOVES
BEFORE BEGINNING CONSTRUCTION. WEAR GLOVES
BEFORE BEGINNING CONSTRUCTION. WEAR GLOVESBEFORE BEGINNING CONSTRUCTION. WEAR GLOVES WHEN HANDLING METAL PARTS.WHEN HANDLING METAL PARTS.
WHEN HANDLING METAL PARTS.
WHEN HANDLING METAL PARTS.WHEN HANDLING METAL PARTS.
Page 2
BEFORE BEFORE
BEFORE
BEFORE BEFORE
A2
Owner's ManualOwner's Manual
Owner's Manual
Owner's ManualOwner's Manual
Before beginning construction, check local building codes regarding footings, location and other requirements. Study and understand this owner's manual. Important information and helpful tips will make your construction easier and more enjoyable.
Assembly Instructions:Assembly Instructions:
Assembly Instructions: Instructions are supplied in this manual and contain all
Assembly Instructions:Assembly Instructions:
appropriate information for your building model. Review all instructions before you begin, and during assembly, follow the step sequence carefully for correct results.
FF
oundaounda
F
ounda
FF
oundaounda
tion and tion and
tion and
tion and tion and
AncAnc
Anc
AncAnc
horhor
ing:ing:
hor
ing: Your storage building must be anchored to pre vent wind
horhor
ing:ing:
YY
OU BEGINOU BEGIN
Y
OU BEGIN
YY
OU BEGINOU BEGIN
........
....
........
damage. A foundation is also necessary as a base in order to construct a square and level building. Anchoring and foundation materials are not included with your building. We recommend the combined use of an
AncAnc
horing Kithoring Kit
Anc
horing Kit as an effective method of secur ing your building to the ground (Available
AncAnc
horing Kithoring Kit
by mail order or at your local dealer) or you may construct the foundation and anchoring system of your choice. Your assembly instructions provide infor mation on a few methods commonly used to secure and level a storage building.
PP
arar
ts and Pts and P
P
ar
ts and P
PP
arar
ts and Pts and P
building.
•All part numbers can be found on the parts. All of these numbers (before the -) must agree with the numbers on the parts list. The parts list is located on page 12.
•If you find that a part is missing, include the model number of your building and contact:
Arrow Group Industries, Inc. Customer Service DepartmentArrow Group Industries, Inc. Customer Service Department
Arrow Group Industries, Inc. Customer Service Department
Arrow Group Industries, Inc. Customer Service DepartmentArrow Group Industries, Inc. Customer Service Department Route 50 East Breese, Illinois 62230Route 50 East Breese, Illinois 62230
Route 50 East Breese, Illinois 62230
Route 50 East Breese, Illinois 62230Route 50 East Breese, Illinois 62230
arar
ts List:ts List:
ar
ts List: Check to be sure that y ou have all the necessary parts for your
arar
ts List:ts List:
Arrow Floor Foundation Kit Arrow Floor Foundation Kit
Arrow Floor Foundation Kit and an
Arrow Floor Foundation Kit Arrow Floor Foundation Kit
Arrow Arrow
Arrow
Arrow Arrow
1-800-851-10851-800-851-1085
1-800-851-1085
1-800-851-10851-800-851-1085
•Separate contents of the carton by the part number while reviewing parts list. The first few steps show how to join related parts to make larger sub assemblies which will be used later.
•Familiarize yourself with the hardware and fasteners for easier use during construction. These are packaged within the carton. Note that extra fasteners have been supplied for your convenience.
2
Page 3
PLAN PLAN
PLAN
PLAN PLAN
A3
WW
aa
tctc
W
WW
Do not attempt to assemble your building on a windy day. Be careful on wet or muddy ground.
TT
T
TT
your building. One person can position parts or panels while the other is able to handle the fasteners and the tools.
TT
T
TT
construction of your building. Decide which method of anchoring and the type of foundation you wish to use in order to form a complete list of the mater ials you will need.
h the h the
a
tc
h the
aa
tctc
h the h the
eamweamw
eamw
eamweamw
ools and Maools and Ma
ools and Ma
ools and Maools and Ma
oror
or
oror
WW
eaea
ther:ther:
ea
ther:
eaea
ther:ther:
Whenever possible, two or more people should work together to assemble
terter
ter
terter
k:k:
k:
k:k:
W
WW
Be sure the day you select to install y our building is dry and calm.
ials:ials:
ials:
ials:ials:
These are some basic tools and materials you will need for the
AHEADAHEAD
AHEAD
AHEADAHEAD
........
....
........
Required
• Eye Goggles
• No. 2 Phillips Screwdriver
(With Hardened Magnetic Tip) Note: A power screwdriver or vari­able speed drill with Phillips-tip at­tachment can speed assembly by as much as 40%.
Selecting and PrSelecting and Pr
Selecting and Pr
Selecting and PrSelecting and Pr
a location for your building. The best location is a level area with good drainage.
•Allow enough working space for ease of moving parts into position during assembly. Be sure there will be enough space at entrance for doors to open fully and enough space around the building to be able to fasten the panel screws from the outside.
•Before you begin the first steps in assembling your parts, a foundation should be constructed and an anchoring system should be ready to use.
• Work Gloves
• Step Ladder
• Utility Knife / Scissors
• Pliers
• Carpenter's Level
• Tape Measure
ee
parpar
e
par
ee
parpar
Required
ing ing
ing
ing ing
YY
our Site:our Site:
Y
our Site:
YY
our Site:our Site:
Optional Time-Savers
• Wrench / Nut Driver
• Electric / Cordless Drill
• Square
• String (for squaring frame)
Before assembly, you will want to decide on
Foundation Preparation
• Hammer and Nails
• Spade or Shovel
• Hand Saw / Power Saw
• Lumber and/or Concrete
3
Page 4
SAFETY FIRSTSAFETY FIRST
SAFETY FIRST
SAFETY FIRSTSAFETY FIRST
A4
Safety precautions are important to follow throughout the construction of your building.Safety precautions are important to follow throughout the construction of your building.
Safety precautions are important to follow throughout the construction of your building.
Safety precautions are important to follow throughout the construction of your building.Safety precautions are important to follow throughout the construction of your building.
........
....
........
•Care must be taken when handling various pieces of your building since some contain sharp edges. Please wear work gloves, eye protection and long sleeves when assembling or performing any maintenance on your build­ing.
safety edge
sharp edge
sharp edge
safety edge
•Keep children and pets away from worksite to avoid distractions and any accidents which may occur.
•Practice caution with the tools being used in the assembly of this building. Be familiar with the operation of all power tools.
•Do not attempt to assemble the building if parts are missing because any building left partially assembled may be seriously damaged by light winds. Call 1-800-851-1085
•Never concentrate your total weight on the roof of the building. When using a step ladder make sure that it is fully open and on even ground before climbing on it.
4
•Do not attempt to assemble the building on a windy day, because the large panels acting as a "sail", can be whipped about by the wind making construction difficult and unsafe.
Page 5
CARE & MAINTENCARE & MAINTEN
CARE & MAINTEN
CARE & MAINTENCARE & MAINTEN
A5 Web
FF
inish:inish:
F
inish: For long lasting finish, periodically clean and wax the exterior surface. Touch-
FF
inish:inish:
up scratches as soon as you notice them on your unit. Immediately clean the area with a wire brush; wash it and apply touch-up paint per manufacturer's recommendation.
ANCE....ANCE....
ANCE....
ANCE....ANCE....
Roof:Roof:
Roof:
Roof:Roof:
amounts of snow on roof can damage building making it unsafe to enter. In snow country, Roof Strengthening Kits are available for most Arrow Buildings for added protection against heavy snow accumulation.
DoorDoor
Door
DoorDoor
sliding easily. Lubricate door track annually with furniture polish or silicone spray. Keep doors closed and locked to prevent wind damage.
FF
astenerastener
F
astener
FF
astenerastener
the metal from being scratched by scre ws. Regularly check your b uilding f or loose scre ws, bolts, nuts, etc. and retighten them as necessary.
Moisture: Moisture:
Moisture: A plastic sheet (vapor barrier) placed under the entire floor area with good
Moisture: Moisture:
ventilation will reduce condensation.
Other Other
Other
Other Other
Keep roof clear of leaves and snow with long handled, soft-bristled broom. Heavy
s:s:
s:
Always keep the door trac ks clear of dirt and other debris that prevent them from
s:s:
s:s:
s:
Use all washers supplied to protect against weather infiltration and to protect
s:s:
TT
ips....ips....
T
ips....
TT
ips....ips....
• Wash off inked part numbers on coated panels with soap and water.
• Silicone caulking may be used for watertight seals throughout the building.
Do not store swimming pool chemicals in your building. Combustibles andDo not store swimming pool chemicals in your building. Combustibles and
Do not store swimming pool chemicals in your building. Combustibles and
Do not store swimming pool chemicals in your building. Combustibles andDo not store swimming pool chemicals in your building. Combustibles and corrosives must be stored in air tight approved containers.corrosives must be stored in air tight approved containers.
corrosives must be stored in air tight approved containers.
corrosives must be stored in air tight approved containers.corrosives must be stored in air tight approved containers.
Keep this Owner's Manual and Assembly Instructions for future reference.Keep this Owner's Manual and Assembly Instructions for future reference.
Keep this Owner's Manual and Assembly Instructions for future reference.
Keep this Owner's Manual and Assembly Instructions for future reference.Keep this Owner's Manual and Assembly Instructions for future reference.
5
Page 6
AA
CCESSORIESCCESSORIES
A
CCESSORIES
AA
CCESSORIESCCESSORIES
A6 WEB
RR
OOF STRENGTHENING (heaOOF STRENGTHENING (hea
R
OOF STRENGTHENING (hea
RR
OOF STRENGTHENING (heaOOF STRENGTHENING (hea
designed for added protection against heavy snow accumulation. Increases the strength of your roof by 50%.
ANCHOR KITANCHOR KIT
ANCHOR KIT
ANCHOR KITANCHOR KIT
Model No. AK4Model No. AK4
Model No. AK4
Model No. AK4Model No. AK4
Anchor Kit contains heavy-duty steel augers, 60' (18m) of steel cable and 4 cable clamps. No digging or concrete pouring, just insert cable under roof, over roof beams, into augers and twist augers into the ground. For buildings
larger than 10'x9', use 2 kits.
vy snovy sno
vy sno
vy snovy sno
w load) KITSw load) KITS
w load) KITS Extra roof beams and gable braces
w load) KITSw load) KITS
ANCHOR KITANCHOR KIT
ANCHOR KIT
ANCHOR KITANCHOR KIT
Model No. AK100Model No. AK100
Model No. AK100
Model No. AK100Model No. AK100
New concrete anchor system permits anchoring any size Arrow building directly to a concrete slab. Each kit contains heavy-duty, hot-dipped galvanized steel corner gussets and perimeter clips which fit over the floor frame and lag bolt into a concrete slab. Full assembly instructions and a 1/4" masonary drill bit are included.
........
....
........
FLOOR FOUNDFLOOR FOUND
FLOOR FOUND
FLOOR FOUNDFLOOR FOUND
MODELS FB47410, FB5465, FB106-A
FB109-A, FB1010 AND FB1014-A
A simple new floor frame system made of heavy-duty, hot-dipped galvanized steel. Use as foundation for plywood, sand or stone.
TT
OOL HANGING RAOOL HANGING RA
T
OOL HANGING RA
TT
OOL HANGING RAOOL HANGING RA
Model No. TH100Model No. TH100
Model No. TH100
Model No. TH100Model No. TH100
The perfect tool organizer. Twin 25 1/2" (65cm) steel channels plus five heavy-duty snap-in hangers and a small tool holder for screwdrivers, pliers, etc. Holders slide along channel for fully adjustable spacing. Great for garage, basement, or the back of any door. Fits all Arrow storage buildings.
6
AA
TION KITSTION KITS
A
TION KITS
AA
TION KITSTION KITS
CKCK
CK
CKCK
AA
TTIC KIT / TTIC KIT /
A
TTIC KIT /
AA
TTIC KIT / TTIC KIT /
Heavy-duty galvanized steel bars that fit all 10' wide Arrow buildings. They install quickly and easily to help organize space and create more useable space as an attic or workbench. Will hold up to 250 lbs. (113kg) evenly distributed.
Model No.Model No.
Model No.
Model No.Model No.
Must be drilled for use as workbench in Estator. + Even weight distribution.
SHELF UNITSSHELF UNITS
SHELF UNITS
SHELF UNITSSHELF UNITS
Heavy-duty, galvanized steel shelf units help organize storage space. They easily mount on the wall or sit on the floor. Fits all Arrow buildings.*
Model No. SS404
• Makes 8" to 12" (20-30cm) wide shelves in any length.
• Brackets, braces, hardware included. Lumber is not included.
* Some drilling required to fit buildings without mid-wall bracing.
WW
ORKBENCH KITORKBENCH KIT
W
ORKBENCH KIT
WW
ORKBENCH KITORKBENCH KIT
FitsFits
Fits
FitsFits
10' Long, 250 lb. (113kg) load+
Fits all Arrow 10' wide buildings.
Model No. SS900-A
• Grey color
• 3 shelves
• Holds up to 85 lbs. (38kg) (even weight distribution)
Shipping WeightShipping Weight
Shipping Weight
Shipping WeightShipping Weight
16 lbs. (7kg)AT101
Page 7
THIS
PAGE
WAS
LEFT
BLANK
INTENTIONALLY
7
Page 8
THIS
PAGE
WAS
LEFT
BLANK
INTENTIONALLY
8
Page 9
FF
oundaounda
F
ounda
FF
oundaounda
BW9
TT
he Fhe F
T
he F
TT
he Fhe F
Concrete SlabConcrete Slab
Concrete Slab
Concrete SlabConcrete Slab
The slab should be at least 3" to 4" (8-10cm) thick. It must be level and flat to provide good support for the frame.The slab should be at least 3" to 4" (8-10cm) thick. It must be level and flat to provide good support for the frame.
The slab should be at least 3" to 4" (8-10cm) thick. It must be level and flat to provide good support for the frame.
The slab should be at least 3" to 4" (8-10cm) thick. It must be level and flat to provide good support for the frame.The slab should be at least 3" to 4" (8-10cm) thick. It must be level and flat to provide good support for the frame. The following are the recommended materials for your foundation.The following are the recommended materials for your foundation.
The following are the recommended materials for your foundation.
The following are the recommended materials for your foundation.The following are the recommended materials for your foundation.
● 2 x 4's (5cm x 10cm) (will be removed once the concrete cures)
● Concrete ● Sheet of 6 mil plastic
● We recommend for a proper strength concrete to use a mix of: 1 part cement ● 3 parts pea sized gravel ● 2 1/2 parts clean sand
Prepare the Site/Construct a FoundationPrepare the Site/Construct a Foundation
Prepare the Site/Construct a Foundation
Prepare the Site/Construct a FoundationPrepare the Site/Construct a Foundation
1. Dig a square, 6" (15cm) deep into the ground (remove grass).
2. Fill up to 4" (10cm) in the square with gravel and tamp firm.
3. Cover gravel with a sheet of 6 mil plastic.
4. Construct a wood frame using four planks of 2x4 (5cm x 10cm) lumber.
5. Pour in concrete to fill in the hole and the frame giving a total of 4" (8-10cm) thick concrete. Be sure surface is level.
oundaounda
ounda
oundaounda
tion Ftion F
tion F
tion Ftion F
or or
or
or or
YY
our Buildingour Building
Y
our Building
YY
our Buildingour Building
tiontion
tion
tiontion
Allow 3 - 5 hours for construction and a week for concrete curing time.Allow 3 - 5 hours for construction and a week for concrete curing time.
Allow 3 - 5 hours for construction and a week for concrete curing time.
Allow 3 - 5 hours for construction and a week for concrete curing time.Allow 3 - 5 hours for construction and a week for concrete curing time.
Note: Before beginning construction, check local building codesNote: Before beginning construction, check local building codes
Note: Before beginning construction, check local building codes
Note: Before beginning construction, check local building codesNote: Before beginning construction, check local building codes
regarding footings, location and other requirements.regarding footings, location and other requirements.
regarding footings, location and other requirements.
regarding footings, location and other requirements.regarding footings, location and other requirements.
Welded Wire
Fabric
Reinforcing
Rods
Optional Footer Type of FoundationOptional Footer Type of Foundation
Optional Footer Type of Foundation
Optional Footer Type of FoundationOptional Footer Type of Foundation
141 1/8"141 1/8"
141 1/8"
FRONT (ROLL-UP DOOR)FRONT (ROLL-UP DOOR)
FRONT (ROLL-UP DOOR)
FRONT (ROLL-UP DOOR)FRONT (ROLL-UP DOOR)
141 1/8"141 1/8"
3,58m3,58m
3,58m
3,58m3,58m
10' - 111 3/4"10' - 111 3/4"
10' - 111 3/4"
10' - 111 3/4"10' - 111 3/4"
17' - 198"17' - 198"
17' - 198"
17' - 198"17' - 198"
24' - 284 1/4"24' - 284 1/4"
24' - 284 1/4"
24' - 284 1/4"24' - 284 1/4"
31' - 370 1/2"31' - 370 1/2"
31' - 370 1/2"
31' - 370 1/2"31' - 370 1/2"
2,84m2,84m
2,84m
2,84m2,84m
5,03m5,03m
5,03m
5,03m5,03m
7,22m7,22m
7,22m
7,22m7,22m
9,41m9,41m
9,41m
9,41m9,41m
Reinforcing
Rods
Note: Note:
Note: Finished Slab dimensions, with lumber removed.
Note: Note:
9
Page 10
AnchoringAnchoring
Anchoring
AnchoringAnchoring
A10
AncAnc
Anc
AncAnc
It is important that the entire floor frame be anchored after the building is erected.It is important that the entire floor frame be anchored after the building is erected.
It is important that the entire floor frame be anchored after the building is erected.
It is important that the entire floor frame be anchored after the building is erected.It is important that the entire floor frame be anchored after the building is erected.
Below are recommended ways of anchoring.
Arrow Anchoring Kit:Arrow Anchoring Kit:
Arrow Anchoring Kit:
Arrow Anchoring Kit:Arrow Anchoring Kit:
Recommended for use with
Contains: Contains:
Contains: 4 Anchors with Cable, Clamps and
Contains: Contains:
installation instruction.
horhor
hor
horhor
ing Doing Do
ing Do
ing Doing Do
wn wn
TT
wn
T
wn wn
TT
(Model No. AK4 or 60298)
any any
any suggested
any any
he Buildinghe Building
he Building
he Buildinghe Building
base.base.
base.
base.base.
Anchoring into Wood/Post:Anchoring into Wood/Post:
Anchoring into Wood/Post:
Anchoring into Wood/Post:Anchoring into Wood/Post:
Use 1/4" Wood Screws. There are 1/4" (0,63cm) dia. holes provided in the frames for proper anchoring.
1. 2.
OVER THE BEAMS
AND INTO THE GROUND
Arrow Anchoring Kit:Arrow Anchoring Kit:
Arrow Anchoring Kit:
Arrow Anchoring Kit:Arrow Anchoring Kit:
Recommended for use with the
Contains: Contains:
Contains: Corner gussets, perimeter clips, hardware,
Contains: Contains:
1/4" masonary drill bit and installation instruction.
(Model No. AK100 or 68383)
concrete concrete
concrete foundation.
concrete concrete
Anchoring into Concrete:Anchoring into Concrete:
Anchoring into Concrete:
Anchoring into Concrete:Anchoring into Concrete:
1. For poured concrete slab or footing or patio blocks: Use 1/4" x 2" Lag Screws.
2. For Anchor Post of Concrete poured after building is erected: Use 1/4" x 6" Lag Screws.
1.
2.
10
Page 11
BW11
6500465004
65004
6500465004
#8Ax5/16" Screw (403)#8Ax5/16" Screw (403)
#8Ax5/16" Screw (403)
#8Ax5/16" Screw (403)#8Ax5/16" Screw (403)
(190) (Carton 4)(190) (Carton 4)
(190) (Carton 4)
(190) (Carton 4)(190) (Carton 4)
HarHar
Har
HarHar
dd
d
dd
6510165101
65101
6510165101
1/4-20 Square Nut (10)1/4-20 Square Nut (10)
1/4-20 Square Nut (10)
1/4-20 Square Nut (10)1/4-20 Square Nut (10)
(Packed with Screws)(Packed with Screws)
(Packed with Screws)
(Packed with Screws)(Packed with Screws)
ww
w
ww
arar
ar
arar
e fe f
or Buildingor Building
e f
or Building
e fe f
or Buildingor Building
6510665106
65106
6510665106
#10-32 Square Nut (200)#10-32 Square Nut (200)
#10-32 Square Nut (200)
#10-32 Square Nut (200)#10-32 Square Nut (200)
(184) (Carton 4)(184) (Carton 4)
(184) (Carton 4)
(184) (Carton 4)(184) (Carton 4)
Remove from bag of screwsRemove from bag of screws
Remove from bag of screws
Remove from bag of screwsRemove from bag of screws
and save for the Step 28and save for the Step 28
and save for the Step 28
and save for the Step 28and save for the Step 28
6594365943
65943
6594365943
#10-32x7/16" Bolt (194)#10-32x7/16" Bolt (194)
#10-32x7/16" Bolt (194)
#10-32x7/16" Bolt (194)#10-32x7/16" Bolt (194)
(184) (Carton 4)(184) (Carton 4)
(184) (Carton 4)
(184) (Carton 4)(184) (Carton 4)
6598965989
65989
6598965989
1/4-20x1/2" Hex Head Bolt (10)1/4-20x1/2" Hex Head Bolt (10)
1/4-20x1/2" Hex Head Bolt (10)
1/4-20x1/2" Hex Head Bolt (10)1/4-20x1/2" Hex Head Bolt (10)
(Packed with Screws)(Packed with Screws)
(Packed with Screws)
(Packed with Screws)(Packed with Screws)
6664666646
66646
6664666646
Washer (600)Washer (600)
Washer (600)
Washer (600)Washer (600)
(320) (Carton 4)(320) (Carton 4)
(320) (Carton 4)
(320) (Carton 4)(320) (Carton 4)
79727972
7972
79727972
Door Handle Lock Bracket (1)Door Handle Lock Bracket (1)
Door Handle Lock Bracket (1)
Door Handle Lock Bracket (1)Door Handle Lock Bracket (1)
6540865408
65408
6540865408
#10-32x1/4" Bolts (4)#10-32x1/4" Bolts (4)
#10-32x1/4" Bolts (4)
#10-32x1/4" Bolts (4)#10-32x1/4" Bolts (4)
6644466444
66444
6644466444
Roof Trim CapRoof Trim Cap
Roof Trim Cap
Roof Trim CapRoof Trim Cap
(2 right & 2 left)(2 right & 2 left)
(2 right & 2 left)
(2 right & 2 left)(2 right & 2 left)
67545 21'67545 21'
67545 21'
67545 21'67545 21'
Weather Stripping (1)Weather Stripping (1)
Weather Stripping (1)
Weather Stripping (1)Weather Stripping (1)
65900A65900A
65900A
65900A65900A
#10Bx1/2" Black Screw (2)#10Bx1/2" Black Screw (2)
#10Bx1/2" Black Screw (2)
#10Bx1/2" Black Screw (2)#10Bx1/2" Black Screw (2)
(Packed with Screws)(Packed with Screws)
(Packed with Screws)
(Packed with Screws)(Packed with Screws)
66446 (Arrow Logo)66446 (Arrow Logo)
66446 (Arrow Logo)
66446 (Arrow Logo)66446 (Arrow Logo)
Peak Cap (2)Peak Cap (2)
Peak Cap (2)
Peak Cap (2)Peak Cap (2)
67293 10'67293 10'
67293 10'
67293 10'67293 10'
Weather Stripping (1)Weather Stripping (1)
Weather Stripping (1)
Weather Stripping (1)Weather Stripping (1)
(Carton 4)(Carton 4)
(Carton 4)
(Carton 4)(Carton 4)
6591465914
65914
6591465914
#6Ax7/8"Screw (5)#6Ax7/8"Screw (5)
#6Ax7/8"Screw (5)
#6Ax7/8"Screw (5)#6Ax7/8"Screw (5)
(Packed with Screws)(Packed with Screws)
(Packed with Screws)
(Packed with Screws)(Packed with Screws)
66610 (No Slot)66610 (No Slot)
66610 (No Slot)
66610 (No Slot)66610 (No Slot)
#10-32x7/16" Bolt (2)#10-32x7/16" Bolt (2)
#10-32x7/16" Bolt (2)
#10-32x7/16" Bolt (2)#10-32x7/16" Bolt (2)
6626566265
66265
6626566265
Edge Trim (4)Edge Trim (4)
Edge Trim (4)
Edge Trim (4)Edge Trim (4)
(Carton 4)(Carton 4)
(Carton 4)
(Carton 4)(Carton 4)
6609866098
66098
6609866098
Plastic Spacer (5)Plastic Spacer (5)
Plastic Spacer (5)
Plastic Spacer (5)Plastic Spacer (5)
6624266242
66242
6624266242
Door Slide (2)Door Slide (2)
Door Slide (2)
Door Slide (2)Door Slide (2)
6626066260
66260
6626066260
Handle (2)Handle (2)
Handle (2)
Handle (2)Handle (2)
6638266382
66382
6638266382
Lower Door Guide (2)Lower Door Guide (2)
Lower Door Guide (2)
Lower Door Guide (2)Lower Door Guide (2)
11
Page 12
Parts ListParts List
Parts List
BW12
Carton #4 of the VT1217 can be deleted for a complete 12'x10' building, or more than one carton #4 may be used to extend depth in multiples of 7'.
Assembly Part Part Key No. Number Description Carton 1 Carton 2 Carton 3 Carton 4
1 7855 Truss Lower Chord 2 2 7856 Truss Upper Chord 2 3 6382 Center Gable Brace 2 8 4 7739 Truss Diagonal 4 5 6381 Mid Gable Brace 4 4 6 6380 Outer Gable Brace 4 4 7 7738 Splice Plate 1 8 7834 Right Front Frame 3 9 7837 Side Frame 4 10 7914 Side Frame 4 11 8532 Right Rear Frame 3 12 8531 Left Rear Frame 3 13 7835 Left Front Frame 3 14 7857 Truss Support 2 2 15 7824 Corner Wall Panel 4 16 7825 Front Wall Panel 2 17 7822 Main Wall Panel 7 6 18 6228 Frame Support 4 19 7917 Truss Column 2 20 7839 Front Column 2 21 7831 Lintel 1 22 7915 Side Top Angle 2 23 7838 Side Top Angle 2 24 7823 Medium Wall Panel 1 25 7833 Roof Beam 6 26 7912 Roof Beam 6 27 7942 Right Gable 2 28 7943 Left Gable 2 29 7840 Right Track Support 1 30 7841 Left Track Support 1 31 6372 Gable Strut 2 2 32 7827 Left Roof Panel 2 33 7826 Right Roof Panel 2 34 7828 Middle Roof Panel 4 6 35 7843 Ridge Cap 1 1 36 6874 Ridge Cap 1 37 5220 Side Roof Trim 2 2 38 6014 Side Roof Trim 2 39 7845 Left Rake 2 40 7846 Right Rake 2 41 7913 Spring Support Bracket 2 42 7830 Right Door Jamb 1 43 7829 Left Door Jamb 1 44 7517 Lower Door Track 1 45 7560 Ramp 1 46 7950 Side Wall Channel 1 47 7949 Side Wall Channel 1 48 7951 Support Column 1 49 7958 Door Track 1 50 7946 Door Jamb 2 51 7948 Door Wall Brace 1 52 7945 Door 1 53 3719 Door Handle Brace 1 54 7947 Vertical Door Brace 1 55 6264 Horizontal Door Brace 2 56 8530 Splice Channel 1 57 9286 Door Panel (Bottom) 1 58 7808 Bottom Angle 1 59 8198 Vinyl Weatherstrip 1 60 7848 Door Panel (Lock) 1 61 67510 Right Vertical Track 1 62 67509 Left Vertical Track 1 63 67476 Right Horizontal Tack 1 64 67475 Left Horizontal Track 1 65 7847 Door Panel (Top) 1
Parts ListParts List
12
Page 13
BW13
AssembAssemb
Assemb
AssembAssemb
ll
y by b
l
y b
ll
y by b
y Ky K
y K
y Ky K
ee
y No.y No.
e
y No.
ee
y No.y No.
13
Page 14
BW14
65101 (16)65101 (16)
65101 (16)
65101 (16)65101 (16)
1/4-20 Square Nut1/4-20 Square Nut
1/4-20 Square Nut
1/4-20 Square Nut1/4-20 Square Nut
(Packed with Screws)(Packed with Screws)
(Packed with Screws)
(Packed with Screws)(Packed with Screws)
66432 (4)66432 (4)
66432 (4)
66432 (4)66432 (4)
3/8-16x1 1/2" Hex3/8-16x1 1/2" Hex
3/8-16x1 1/2" Hex
3/8-16x1 1/2" Hex3/8-16x1 1/2" Hex
Head BoltHead Bolt
Head Bolt
Head BoltHead Bolt
HarHar
Har
HarHar
1/4-20 1 1/2" Hex1/4-20 1 1/2" Hex
1/4-20 1 1/2" Hex
1/4-20 1 1/2" Hex1/4-20 1 1/2" Hex
Head BoltHead Bolt
Head Bolt
Head BoltHead Bolt
3/8-16 Hex Nut3/8-16 Hex Nut
3/8-16 Hex Nut
3/8-16 Hex Nut3/8-16 Hex Nut
dd
ww
d
w
dd
ww
66464 (2)66464 (2)
66464 (2)
66464 (2)66464 (2)
66433 (4)66433 (4)
66433 (4)
66433 (4)66433 (4)
arar
ar
arar
e fe f
or Roll-Up-Dooror Roll-Up-Door
e f
or Roll-Up-Door
e fe f
or Roll-Up-Dooror Roll-Up-Door
65989 (6)65989 (6)
65989 (6)
65989 (6)65989 (6)
1/4-20x1/2" Hex1/4-20x1/2" Hex
1/4-20x1/2" Hex
1/4-20x1/2" Hex1/4-20x1/2" Hex
Head BoltHead Bolt
Head Bolt
Head BoltHead Bolt
(Packed with Screws)(Packed with Screws)
(Packed with Screws)
(Packed with Screws)(Packed with Screws)
66434 (2)66434 (2)
66434 (2)
66434 (2)66434 (2)
#10-32 x 2 1/2" Flat#10-32 x 2 1/2" Flat
#10-32 x 2 1/2" Flat
#10-32 x 2 1/2" Flat#10-32 x 2 1/2" Flat
Head BoltHead Bolt
Head Bolt
Head BoltHead Bolt
65106 (16)65106 (16)
65106 (16)
65106 (16)65106 (16)
#10-32 Square#10-32 Square
#10-32 Square
#10-32 Square#10-32 Square
NutNut
Nut
NutNut
65900A (38)65900A (38)
65900A (38)
65900A (38)65900A (38)
#10Bx1/2" Black#10Bx1/2" Black
#10Bx1/2" Black
#10Bx1/2" Black#10Bx1/2" Black
Truss Head ScrewTruss Head Screw
Truss Head Screw
Truss Head ScrewTruss Head Screw
(Packed with Screws)(Packed with Screws)
(Packed with Screws)
(Packed with Screws)(Packed with Screws)
66431 (8)66431 (8)
66431 (8)
66431 (8)66431 (8)
1/4-20x5/8" Rib1/4-20x5/8" Rib
1/4-20x5/8" Rib
1/4-20x5/8" Rib1/4-20x5/8" Rib
Neck BoltNeck Bolt
Neck Bolt
Neck BoltNeck Bolt
66441 (14)66441 (14)
66441 (14)
66441 (14)66441 (14)
#10-32x3/8" Bolt#10-32x3/8" Bolt
#10-32x3/8" Bolt
#10-32x3/8" Bolt#10-32x3/8" Bolt
6752567525
67525
6752567525
Inside "T" HandleInside "T" Handle
Inside "T" Handle
Inside "T" HandleInside "T" Handle
(1)(1)
(1)
(1)(1)
6750467504
67504
6750467504
Inside Latch BarInside Latch Bar
Inside Latch Bar
Inside Latch BarInside Latch Bar
Spacer (1)Spacer (1)
Spacer (1)
Spacer (1)Spacer (1)
6749167491
67491
6749167491
#2 Hinge#2 Hinge
#2 Hinge
#2 Hinge#2 Hinge
(2)(2)
(2)
(2)(2)
6748367483
67483
6748367483
Cable LacerCable Lacer
Cable Lacer
Cable LacerCable Lacer
(2)(2)
(2)
(2)(2)
6748267482
67482
6748267482
Keyed CableKeyed Cable
Keyed Cable
Keyed CableKeyed Cable
(2)(2)
(2)
(2)(2)
6749367493
67493
6749367493
Top FixtureTop Fixture
Top Fixture
Top FixtureTop Fixture
(2)(2)
(2)
(2)(2)
6750067500
67500
6750067500
SpringSpring
Spring
SpringSpring
(2)(2)
(2)
(2)(2)
6748467484
67484
6748467484
Spring ClevisSpring Clevis
Spring Clevis
Spring ClevisSpring Clevis
(2)(2)
(2)
(2)(2)
6748567485
67485
6748567485
Left BottomLeft Bottom
Left Bottom
Left BottomLeft Bottom
Bracket (1)Bracket (1)
Bracket (1)
Bracket (1)Bracket (1)
6749467494
67494
6749467494
Lift HandleLift Handle
Lift Handle
Lift HandleLift Handle
(2)(2)
(2)
(2)(2)
67528 Latch Set67528 Latch Set
67528 Latch Set
67528 Latch Set67528 Latch Set
(1) Flat Latch Bar(1) Flat Latch Bar
(1) Flat Latch Bar
(1) Flat Latch Bar(1) Flat Latch Bar
(4) "S" Hooks(4) "S" Hooks
(4) "S" Hooks
(4) "S" Hooks(4) "S" Hooks
(2) Strikers(2) Strikers
(2) Strikers
(2) Strikers(2) Strikers
(2) Spring Latches(2) Spring Latches
(2) Spring Latches
(2) Spring Latches(2) Spring Latches
(2) Latch Chains(2) Latch Chains
(2) Latch Chains
(2) Latch Chains(2) Latch Chains
6748867488
67488
6748867488
Heavy "S" HookHeavy "S" Hook
Heavy "S" Hook
Heavy "S" HookHeavy "S" Hook
(4)(4)
(4)
(4)(4)
6748667486
67486
6748667486
Right BottomRight Bottom
Right Bottom
Right BottomRight Bottom
Bracket (1)Bracket (1)
Bracket (1)
Bracket (1)Bracket (1)
6749667496
67496
6749667496
RollerRoller
Roller
RollerRoller
(8)(8)
(8)
(8)(8)
6751367513
67513
6751367513
Spring RestraintSpring Restraint
Spring Restraint
Spring RestraintSpring Restraint
Cable (2)Cable (2)
Cable (2)
Cable (2)Cable (2)
6750367503
67503
6750367503
Stile SpacerStile Spacer
Stile Spacer
Stile SpacerStile Spacer
(2)(2)
(2)
(2)(2)
6749067490
67490
6749067490
#1 Hinge#1 Hinge
#1 Hinge
#1 Hinge#1 Hinge
(4)(4)
(4)
(4)(4)
6749767497
67497
6749767497
SheaveSheave
Sheave
SheaveSheave
(4)(4)
(4)
(4)(4)
6752667526
67526
6752667526
Locking HandleLocking Handle
Locking Handle
Locking HandleLocking Handle
(1)(1)
(1)
(1)(1)
14
Page 15
TT
rr
uss uss
uss
uss uss
trusstruss
truss
trusstruss
AssembAssemb
Assemb
AssembAssemb
T
r
TT
Step 1Step 1
Step 1
Step 1Step 1
BW15
1 1
1 Assemble 1/2 truss at a time, using
1 1
#10-32x7/16" bolts and square nuts, on all connections loosely.
2 2
2 Attach
2 2
upper chordupper chord
upper chord.
upper chordupper chord
3 3
3 Attach 2
3 3
the upper and lower chords at the opposite end of truss.
4 4
4 Attach 2
4 4
and lower chords.
5 5
5 Attach 2
5 5
upper and lower chords.
6 6
6 Attach 2
6 6
upper and lower chords at middle of truss.
7 7
7 Attach 2
7 7
upper and lower chords. Mount with short leg of brace.
truss lower chordtruss lower chord
truss lower chord to
truss lower chordtruss lower chord
center gable braces center gable braces
center gable braces to
center gable braces center gable braces
truss diagonalstruss diagonals
truss diagonals to upper
truss diagonalstruss diagonals
mid gable bracesmid gable braces
mid gable braces to
mid gable bracesmid gable braces
center gable bracescenter gable braces
center gable braces to
center gable bracescenter gable braces
outer gable bracesouter gable braces
outer gable braces to
outer gable bracesouter gable braces
rr
● Parts Needed For ●
ll
y 12x17,y 12x17,
l
y 12x17,
ll
y 12x17,y 12x17,
ONLONL
ONL
ONLONL
6382
12x24 & 12x31 12x24 & 12x31
12x24 & 12x31
12x24 & 12x31 12x24 & 12x31
YY
Y
YY
The day before construction of the building, complete the sub­assemblies so they will be ready. EXAMPLE: Truss, floor frames, roof beams, gables, side and overhead doors. Set the assemblies aside, so they will not get damaged. The remainder of the building assembly requires more than 1 work session and more than 1 person. Do not continue beyond this point if you do not have enough time to complete the wall assembly and can tie down the assembly overnight. Complete the roof and doors on the following day.
●●
7855 Truss Lower Chord (2) 7855 Truss Lower Chord (2)
●
7855 Truss Lower Chord (2)
●●
7855 Truss Lower Chord (2) 7855 Truss Lower Chord (2)
●●
7856 Truss Upper Chord (2) 7856 Truss Upper Chord (2)
●
7856 Truss Upper Chord (2)
●●
7856 Truss Upper Chord (2) 7856 Truss Upper Chord (2)
●●
6382 Center Gable Brace (8) 6382 Center Gable Brace (8)
●
6382 Center Gable Brace (8)
●●
6382 Center Gable Brace (8) 6382 Center Gable Brace (8)
●●
7739 Truss Diagonal (4) 7739 Truss Diagonal (4)
●
7739 Truss Diagonal (4)
●●
7739 Truss Diagonal (4) 7739 Truss Diagonal (4)
●●
6381 Mid Gable Brace (4) 6381 Mid Gable Brace (4)
●
6381 Mid Gable Brace (4)
●●
6381 Mid Gable Brace (4) 6381 Mid Gable Brace (4)
●●
6380 Outer Gable Brace (4) 6380 Outer Gable Brace (4)
●
6380 Outer Gable Brace (4)
●●
6380 Outer Gable Brace (4) 6380 Outer Gable Brace (4)
●●
7738 Splice Plate (1) 7738 Splice Plate (1)
●
7738 Splice Plate (1)
●●
7738 Splice Plate (1) 7738 Splice Plate (1)
8 8
8 Square up 1/2 truss, adjust and
8 8
tighten.
9 9
9 Make other half and square.
9 9 10 10
10 Splice both halves together with
10 10
splice platesplice plate
splice plate and fasten center gable
splice platesplice plate
braces together, using 3 bolts and nuts.
11 11
11 Cut the 4 pieces of
11 11
half and slip over the bottom edges of gable braces. This trim is a must to protect against injury from the sharp edge. Make 1 assembly for the 12x17 Make 2 assemblies for the 12x24 Make 3 assemblies for the 12x31
NOTENOTE
NOTE
NOTENOTE
edge trim edge trim
edge trim in
edge trim edge trim
IMPORTANT:IMPORTANT:
IMPORTANT:
IMPORTANT:IMPORTANT:
Square Up Half Truss
Mounting Flange of Brackets
Must Face Towards Center
Of Truss Assembly
7738
Edge Trim
6381
7739
6380
6382
Short
Mounting
Leg
7856
#10-32 Square Nut
7855
#10-32x7/16" Bolt
15
Page 16
Step 2Step 2
Step 2
Step 2Step 2
BW16
The gables go on top of the front and rear walls to support the roof beams. The gables are packed nested to­gether and might be mistaken as 1 piece. Carefully separate them be­fore continuing.
● Parts Needed For ●
GaGa
bb
les les
Ga
GaGa
b
bb
les
les les
All SizAll Siz
All Siz
All SizAll Siz
eses
es
eses
#10-32 Square Nut
●●
6381 Mid Gable Brace (4) 6381 Mid Gable Brace (4)
●
6381 Mid Gable Brace (4)
●●
6381 Mid Gable Brace (4) 6381 Mid Gable Brace (4)
●●
6380 Outer Gable Brace (4) 6380 Outer Gable Brace (4)
●
6380 Outer Gable Brace (4)
●●
6380 Outer Gable Brace (4) 6380 Outer Gable Brace (4)
●●
7942 Right Gable (2) 7942 Right Gable (2)
●
7942 Right Gable (2)
●●
7942 Right Gable (2) 7942 Right Gable (2)
●●
7943 Left Gable (2) 7943 Left Gable (2)
●
7943 Left Gable (2)
●●
7943 Left Gable (2) 7943 Left Gable (2)
1 1
1 Position
1 1
bracesbraces
braces on
bracesbraces
Short mounting flange of brace must face center of gable. Fasten using #10-32x7/16" bolts, washers and square nuts. Assemble 2 sets of gables.
Step 3Step 3
Step 3
Step 3Step 3
The roof beams join the gables to the truss and supports the roof panels.
11
1Align the holes on 2
11
back-to-back and fasten using 4 #10­32x7/16" bolts and square nuts.
midmid
mid and
midmid
right right
right and
right right
outer gableouter gable
outer gable
outer gableouter gable
left gablesleft gables
left gables.
left gablesleft gables
Short Mounting Flange
Must Face Towards
Center of Gable
Roof Beam Roof Beam
Roof Beam
Roof Beam Roof Beam
roof beamsroof beams
roof beams,
roof beamsroof beams
6381
6380
Washer
● Parts Needed For ●
AssembAssemb
Assemb
AssembAssemb
Small Holes
on Top
lieslies
lies
lieslies
7943
7942
FRONTFRONT
FRONT
FRONTFRONT
#10-32x7/16" Bolt
●●
7833 Roof Beam (2) (All Sizes) 7833 Roof Beam (2) (All Sizes)
●
7833 Roof Beam (2) (All Sizes)
●●
7833 Roof Beam (2) (All Sizes) 7833 Roof Beam (2) (All Sizes)
●●
7912 Roof Beam (2) (1217) 7912 Roof Beam (2) (1217)
●
7912 Roof Beam (2) (1217)
●●
7912 Roof Beam (2) (1217) 7912 Roof Beam (2) (1217)
●●
7912 Roof Beam (4) (1224) 7912 Roof Beam (4) (1224)
●
7912 Roof Beam (4) (1224)
●●
7912 Roof Beam (4) (1224) 7912 Roof Beam (4) (1224)
●●
7912 Roof Beam (6) (1231) 7912 Roof Beam (6) (1231)
●
7912 Roof Beam (6) (1231)
●●
7912 Roof Beam (6) (1231) 7912 Roof Beam (6) (1231)
16
Assembled
End View
7833
#10-32 Square Nut
7912
#10-32x7/16" Bolt
Page 17
Step 4Step 4
Step 4
Step 4Step 4
BW17
● Parts Needed For ●
Floor FFloor F
Floor F
Floor FFloor F
rr
ame ame
r
ame
rr
ame ame
AssembAssemb
Assemb
AssembAssemb
ll
y 12x10y 12x10
l
y 12x10
ll
y 12x10y 12x10
●●
8532 Right Rear Frame (1) 8532 Right Rear Frame (1)
●
8532 Right Rear Frame (1)
●●
8532 Right Rear Frame (1) 8532 Right Rear Frame (1)
●●
8531 Left Rear Frame (1) 8531 Left Rear Frame (1)
●
8531 Left Rear Frame (1)
●●
8531 Left Rear Frame (1) 8531 Left Rear Frame (1)
●●
7837 Side Frame (2) 7837 Side Frame (2)
●
7837 Side Frame (2)
●●
7837 Side Frame (2) 7837 Side Frame (2)
●●
7834 Right Front Frame (1) 7834 Right Front Frame (1)
●
7834 Right Front Frame (1)
●●
7834 Right Front Frame (1) 7834 Right Front Frame (1)
●●
7835 Left Front Frame (1) 7835 Left Front Frame (1)
●
7835 Left Front Frame (1)
●●
7835 Left Front Frame (1) 7835 Left Front Frame (1)
●●
7517 Lower Door Track (1) 7517 Lower Door Track (1)
●
7517 Lower Door Track (1)
●●
7517 Lower Door Track (1) 7517 Lower Door Track (1)
●●
7560 Ramp (1) 7560 Ramp (1)
●
7560 Ramp (1)
●●
7560 Ramp (1) 7560 Ramp (1)
The rear floor frame is made up of 2 pieces. The holes in these pieces will align when the pieces are posi­tioned with correct amount of over­lap. The illustration below shows the proper overall length for the rear.
1 1
1 Overlap
1 1
align holes, and fasten using 8 bolts and nuts. Make 3 assemblies. Use 1 assembly for this step.
right right
right and
right right
7517
left rear framesleft rear frames
left rear frames,
left rear framesleft rear frames
7560
Side Frame
2 2
2 Position
2 2
and fasten at each corner using 2 bolts through the bottom and nuts on top.
3 3
3 Measure the floor frame diago-
3 3
nally. When the diagonal mea­surements are equal, the floor frame is square.
floor frames floor frames
floor frames as shown
floor frames floor frames
STEP
11
1
11
8531
4 4
4 Select location of side door on
4 4
either side, toward the rear of build­ing. Install
rampramp
ramp, notch toward outside, using
rampramp
1/4" bolts and nuts, as shown. See Step 12 for Rear Door Installation.
Do not fasten the floor frames to your foundation at this time. You will anchor the building after it is erected.
The floor frame The floor frame
The floor frame
The floor frame The floor frame
and level and level
and level
and level and level
Rear Frame 140 7/8" 3,6m
lower door tracklower door track
lower door track and
lower door tracklower door track
NOTENOTE
NOTE
NOTENOTE
must be squaremust be square
must be square
must be squaremust be square
or holes will not align.or holes will not align.
or holes will not align.
or holes will not align.or holes will not align.
Notch toward outside
of building
STEP
#10-32x1/4" Bolt
7835
44
4
44
7837
FRONTFRONT
FRONT
FRONTFRONT
7517
Slot
7560
SIDE
STEP
REAR
33
3
33
#10-32 Square Nut
8531
8532
Level
7837
8532
#10-32x7/16" Bolt
STEP
22
2
22
7834
Position with small holes toward outside of building
17
Page 18
Step 5Step 5
Step 5
Step 5Step 5
BW18
● Parts Needed For ●
Floor FFloor F
Floor F
Floor FFloor F
12x17, 12x24, 12x3112x17, 12x24, 12x31
12x17, 12x24, 12x31
12x17, 12x24, 12x3112x17, 12x24, 12x31
rr
ame ame
r
ame
rr
ame ame
AssembAssemb
Assemb
AssembAssemb
●●
8532 Right Rear Frame (1) 8532 Right Rear Frame (1)
●
8532 Right Rear Frame (1)
●●
8532 Right Rear Frame (1) 8532 Right Rear Frame (1)
●●
8531 Left Rear Frame (1) 8531 Left Rear Frame (1)
●
8531 Left Rear Frame (1)
●●
8531 Left Rear Frame (1) 8531 Left Rear Frame (1)
●●
7914 Side Frame (see below) 7914 Side Frame (see below)
●
7914 Side Frame (see below)
●●
ll
yy
l
y
ll
yy
7914 Side Frame (see below) 7914 Side Frame (see below)
●●
7857 Truss Support (see below) 7857 Truss Support (see below)
●
7857 Truss Support (see below)
●●
7857 Truss Support (see below) 7857 Truss Support (see below)
●●
7837 Side Frame (2) 7837 Side Frame (2)
●
7837 Side Frame (2)
●●
7837 Side Frame (2) 7837 Side Frame (2)
●●
7834 Right Front Frame (1) 7834 Right Front Frame (1)
●
7834 Right Front Frame (1)
●●
7834 Right Front Frame (1) 7834 Right Front Frame (1)
●●
7835 Left Front Frame (1) 7835 Left Front Frame (1)
●
7835 Left Front Frame (1)
●●
7835 Left Front Frame (1) 7835 Left Front Frame (1)
●●
7517 Lower Door Track (1) 7517 Lower Door Track (1)
●
7517 Lower Door Track (1)
●●
7517 Lower Door Track (1) 7517 Lower Door Track (1)
●●
7560 Ramp (1) 7560 Ramp (1)
●
7560 Ramp (1)
●●
7560 Ramp (1) 7560 Ramp (1)
The rear floor frame is made up of 2 pieces. The holes in these pieces will align when the pieces are posi­tioned with correct amount of over­lap. The illustration below shows the proper overall length for the rear.
1 1
1 Overlap
1 1
rightright
right and
rightright
left rear framesleft rear frames
left rear frames,
left rear framesleft rear frames
align holes, and fasten using 8 bolts and nuts. Make 3 assemblies. Use 1 assembly for this step.
2 2
2 Position
2 2
floor frames floor frames
floor frames as shown
floor frames floor frames
and fasten at each corner using 2 bolts through the bottom and nuts on top. When installing
side frame 7914side frame 7914
side frame 7914,
side frame 7914side frame 7914
be sure set of holes 1" in from end of frames are installed toward rear of building.
3 3
3 Fasten side frames together with a
3 3
truss supporttruss support
truss support using 4 bolts through
truss supporttruss support
the bottom and nuts on top.
NOTENOTE
NOTE
NOTENOTE
Position of holes, and fasten at
the 1st set of holes. See side
connection.
4 4
4 Measure the floor frame diago-
4 4
nally. When the measurements are equal, the floor frame is square.
5 5
5 Select location of side door on
5 5
either side, toward the rear of build­ing. Install
rampramp
ramp, notch toward outside, using
rampramp
lower door tracklower door track
lower door track and
lower door tracklower door track
1/4" bolts and nuts. See Step 12 for Rear Door Installation.
NOTENOTE
NOTE
NOTENOTE
Do not fasten the floor frames to
your foundation at this time.
You will anchor the building
after it is erected.
IF YOU ARE BUILDING A 12x24 Fasten additional side frame 7914 and truss support 7857 to side frame 7914 using the side connection. Position rear frame at rear of assembly and fasten using the rear corner connection.
IF YOU ARE BUILDING A 12x31 Fasten 2 additional side frames 7914 and truss supports 7857 to side frame 7914 using the side connection. Positon rear frame at rear of assembly and fasten using the rear corner connection.
Level
18
STEP
22
2
22
7835
STEP
33
3
33
7837
FRONTFRONT
FRONT
FRONTFRONT
7837
The floor frame The floor frame
The floor frame
The floor frame The floor frame
and level and level
and level
and level and level
7914
7857
7857
#10-32 Square Nut
7834
Position with small holes toward outside of building
must be squaremust be square
must be square
must be squaremust be square
or holes will not align.or holes will not align.
or holes will not align.
or holes will not align.or holes will not align.
SIDE
7914
#10-32x7/16" Bolt
STEP
44
4
44
7837
REAR
8531
Notch toward outside
of building
8531
8532
STEP
55
5
55
#10-32x1/4" Bolt
7857
7517
STEP
11
1
11
Rear Frame 140 7/8"
8532
Level
7560
7517
7914
7560
Side Frame
3,6m
Slot
Page 19
Step 6Step 6
Step 6
Step 6Step 6
BW19
Each screw and bolt in the wall re­quires a washer.
1 1
1 Install a
1 1
corner of the floor frame as shown. The widest part of each corner panel must be placed along the side of the building for all 4 corners. Fasten the corner panel to the floor frame with 4 screws.
corner wall panelcorner wall panel
corner wall panel at the
corner wall panelcorner wall panel
● Parts Needed For ●
CorCor
nerner
s s
Cor
CorCor
ner
nerner
SIDE
All SizAll Siz
s
All Siz
s s
All SizAll Siz
Wide Side
7824
eses
es
eses
Narrow Side
REAR
TOP VIEW
●●
7824 Corner Wall Panel (4) 7824 Corner Wall Panel (4)
●
7824 Corner Wall Panel (4)
●●
7824 Corner Wall Panel (4) 7824 Corner Wall Panel (4)
●●
7825 Front Wall Panel (2) 7825 Front Wall Panel (2)
●
7825 Front Wall Panel (2)
●●
7825 Front Wall Panel (2) 7825 Front Wall Panel (2)
●●
7822 Main Wall Panel (2) 7822 Main Wall Panel (2)
●
7822 Main Wall Panel (2)
●●
7822 Main Wall Panel (2) 7822 Main Wall Panel (2)
7824
SIDE
Support the corner panel with a step ladder until a wall panel is attached.
2 2
2 Attach the
2 2
front corner panels, as shown.
3 3
3 Attach the
3 3
rear corner panels, as shown.
Be careful to install the correct
panel in each position as shown.
4 4
4 Double-check the part numbers of
4 4
the wall panels, before proceeding.
The floor frame The floor frame
The floor frame
The floor frame The floor frame
and level and level
and level
and level and level
front wall panelsfront wall panels
front wall panels to the
front wall panelsfront wall panels
main wall panelsmain wall panels
main wall panels to the
main wall panelsmain wall panels
NOTENOTE
NOTE
NOTENOTE
must be squaremust be square
must be square
must be squaremust be square
or holes will not align.or holes will not align.
or holes will not align.
or holes will not align.or holes will not align.
STEP
11
1
11
7824
7822
7825
STEP
22
2
22
FRONT
STEP
33
3
33
7824
7822
7825
#8Ax5/16" Screw
STEP
44
4
44
7824 7825
#10-32 Square Nut
#10-32x7/16" Bolt
Washer
7825
7824
7824
Washer
7822
7822
7824
19
Page 20
Step 7Step 7
Step 7
Step 7Step 7
BW20
● Parts Needed For ●
Frames 12x10Frames 12x10
Frames 12x10
Frames 12x10Frames 12x10
●●
Rear Frame Assembly (1) Rear Frame Assembly (1)
●
Rear Frame Assembly (1)
●●
Rear Frame Assembly (1) Rear Frame Assembly (1)
●●
7834 Right Front Frame (1) 7834 Right Front Frame (1)
●
7834 Right Front Frame (1)
●●
7834 Right Front Frame (1) 7834 Right Front Frame (1)
●●
7835 Left Front Frame (1) 7835 Left Front Frame (1)
●
7835 Left Front Frame (1)
●●
7835 Left Front Frame (1) 7835 Left Front Frame (1)
●●
7837 Side Frame (2) 7837 Side Frame (2)
●
7837 Side Frame (2)
●●
7837 Side Frame (2) 7837 Side Frame (2)
●●
7950 Side Wall Channel (1) 7950 Side Wall Channel (1)
●
7950 Side Wall Channel (1)
●●
7950 Side Wall Channel (1) 7950 Side Wall Channel (1)
●●
7949 Side Wall Channel (1) 7949 Side Wall Channel (1)
●
7949 Side Wall Channel (1)
●●
7949 Side Wall Channel (1) 7949 Side Wall Channel (1)
●●
7951 Support Channel (1) 7951 Support Channel (1)
●
7951 Support Channel (1)
●●
7951 Support Channel (1) 7951 Support Channel (1)
The mid frame pieces give rigidity to the side and rear wall.
NOTENOTE
NOTE
NOTENOTE
Before installing mid frames
decide at which location you
want the entrance door. Do not
install the 1x2 mid frame at 1 of 3
locations.
1 1
1 Fasten a
1 1
rear frame assemblyrear frame assembly
rear frame assembly to
rear frame assemblyrear frame assembly
the main wall panels using screws.
2 2
2 Fasten a
2 2
rightright
right and
rightright
left front frameleft front frame
left front frame
left front frameleft front frame
to the front wall panels the same way.
STEP
44
4
44
STEP
55
5
55
SIDE
REAR
3 3
3 Fasten
3 3
side frameside frame
side frame to the corner
side frameside frame
panels using screws. Where rear frame overlaps side frame in corner, fasten using 2 bolts and nuts.
4 4
4 Fasten
4 4
side wall channelsside wall channels
side wall channels to the
side wall channelsside wall channels
corner panels using screws. Fasten overlaps in corners using bolts.
5 5
5 Fasten
5 5
support columnsupport column
support column to side
support columnsupport column
frame and side wall channel using bolts and nuts where shown. Fold corner panel slightly away from col­umn to fasten bolts from outside. See Step 12 for rear door installation.
STEP
#10-32x7/16" Bolt
#8Ax5/16" Screw
7834
7950
STEP
22
2
22
7951
7949
7835
#10-32 Square Nut
8532
11
1
11
8531
7837
STEP
33
3
33
20
Page 21
Step 8Step 8
Step 8
Step 8Step 8
BW21
● Parts Needed For ●
FramesFrames
Frames
FramesFrames
12x17, 12x24 & 12x31 12x17, 12x24 & 12x31
12x17, 12x24 & 12x31
12x17, 12x24 & 12x31 12x17, 12x24 & 12x31
●●
Rear Frame Assembly (1) Rear Frame Assembly (1)
●
Rear Frame Assembly (1)
●●
Rear Frame Assembly (1) Rear Frame Assembly (1)
●●
7834 Right Front Frame (1) 7834 Right Front Frame (1)
●
7834 Right Front Frame (1)
●●
7834 Right Front Frame (1) 7834 Right Front Frame (1)
●●
7835 Left Front Frame (1) 7835 Left Front Frame (1)
●
7835 Left Front Frame (1)
●●
7835 Left Front Frame (1) 7835 Left Front Frame (1)
●●
7917 Truss Column (see below) 7917 Truss Column (see below)
●
7917 Truss Column (see below)
●●
7917 Truss Column (see below) 7917 Truss Column (see below)
●●
7914 Side Frame (see below) 7914 Side Frame (see below)
●
7914 Side Frame (see below)
●●
7914 Side Frame (see below) 7914 Side Frame (see below)
●●
7837 Side Frame (2) 7837 Side Frame (2)
●
7837 Side Frame (2)
●●
7837 Side Frame (2) 7837 Side Frame (2)
●●
6228 Frame Support (4) 6228 Frame Support (4)
●
6228 Frame Support (4)
●●
6228 Frame Support (4) 6228 Frame Support (4)
●●
7949 Side Wall Channel (1) 7949 Side Wall Channel (1)
●
7949 Side Wall Channel (1)
●●
7949 Side Wall Channel (1) 7949 Side Wall Channel (1)
●●
7951 Support Column (1) 7951 Support Column (1)
●
7951 Support Column (1)
●●
7951 Support Column (1) 7951 Support Column (1)
The mid frame pieces give rigidity to the side and rear wall.
NOTENOTE
NOTE
NOTENOTE
Before installing mid frames
decide at which location you
want the entrance door. Do not
install the 1x2 mid frame at 1 of 3
locations.
1 1
1 Fasten a
1 1
rear frame assemblyrear frame assembly
rear frame assembly to
rear frame assemblyrear frame assembly
the main wall panels using screws.
2 2
2 Fasten a
2 2
right right
right and
right right
left front frameleft front frame
left front frame
left front frameleft front frame
to the front wall panels the same way.
3 3
3 Attach 4
3 3
middle of the 2
frame supportsframe supports
frame supports to the
frame supportsframe supports
truss columnstruss columns
truss columns using
truss columnstruss columns
2 bolts and nuts on each.
4 4
4 Fasten
4 4
side frame 7914 side frame 7914
side frame 7914 to the rear
side frame 7914 side frame 7914
corner panel using screws. Be sure set of holes 1" in from end of frame is installed toward rear of building. Where rear frame overlaps side frame in corner, fasten using 2 bolts and nuts. Fasten opposite end to frame support on truss column, using 2 bolts and nuts in the 1st set of holes. Fas­ten truss support to truss column at bottom with 1screw at the 1st hole on column. Support column assembly with step ladder.
STEP
55
5
55
IF YOU ARE BUILDING A 12x24 Each side of building will have 2 column assemblies and 2 extra side frames 7914.
IF YOU ARE BUILDING A 12x31 Each side of building will have 3 column assemblies and 4 extra side frames 7914.
STEP
33
3
33
7917
7837
6228
2nd SET OF HOLES
GAP
FRONT OF BUILDING
For a 12x24 building repeat
column procedure here
#10-32x7/16" Bolt
7837
1st HOLE ON COLUMN
STEP
44
4
44
GAP
7914
7914
1st SET OF HOLES
5 5
5 Fasten
5 5
side frame 7837 side frame 7837
side frame 7837 to the
side frame 7837 side frame 7837
front corner panel using screws. Fas­ten overlap in corner. Fasten oppo­site end to the frame support on truss column, using 2nd set of holes. This will leave a gap between side frame and truss column.
6 6
6 Fasten
6 6
side wall channelside wall channel
side wall channel to the
side wall channelside wall channel
rear corner panel using screws.
7 7
7 Fasten
7 7
support columnsupport column
support column to side
support columnsupport column
frame and side wall channel using bolts and nuts where shown. Fold corner panel slightly away from col­umn to fasten bolts from outside. See Step 12 for rear door installation.
STEP
REAR
SIDE
8532
8531
7951
11
1
11
STEP
77
7
77
7834
#10-32 Square Nut
STEP
22
2
22
7835
7837
#8Ax5/16" Screw
7917
Support this truss column with a
step ladder until next step
7949
STEP
66
6
66
21
Page 22
Step 9Step 9
Step 9
Step 9Step 9
BW22
● Parts Needed For ●
Frames 12x10Frames 12x10
Frames 12x10
Frames 12x10Frames 12x10
●●
7839 Front Column (2) 7839 Front Column (2)
●
7839 Front Column (2)
●●
7839 Front Column (2) 7839 Front Column (2)
●●
7834 Right Front Frame (1) 7834 Right Front Frame (1)
●
7834 Right Front Frame (1)
●●
7834 Right Front Frame (1) 7834 Right Front Frame (1)
●●
7835 Left Front Frame (1) 7835 Left Front Frame (1)
●
7835 Left Front Frame (1)
●●
7835 Left Front Frame (1) 7835 Left Front Frame (1)
●●
7831 Lintel (1) 7831 Lintel (1)
●
7831 Lintel (1)
●●
7831 Lintel (1) 7831 Lintel (1)
●●
Rear Frame Assembly (1) Rear Frame Assembly (1)
●
Rear Frame Assembly (1)
●●
Rear Frame Assembly (1) Rear Frame Assembly (1)
●●
7838 Side Top Angle (2) 7838 Side Top Angle (2)
●
7838 Side Top Angle (2)
●●
7838 Side Top Angle (2) 7838 Side Top Angle (2)
●●
7958 Door Track (1) 7958 Door Track (1)
●
7958 Door Track (1)
●●
7958 Door Track (1) 7958 Door Track (1)
The top frame pieces give rigidity to the side walls and provide a surface for attaching the gables which sup­port the roof.
1 1
1 Fasten
1 1
front columnsfront columns
front columns to the bot-
front columnsfront columns
tom and mid front frames with bolts and nuts. Flange with 2 holes at each end must be facing outside. Fold front panel slightly away from column to tighten bolts and nuts.
2 2
2 Fasten
2 2
rightright
right and
rightright
left front frameleft front frame
left front frame
left front frameleft front frame
to the top of front wall panels using 4 screws.
3 3
3 Position
3 3
lintellintel
lintel across top of frames
lintellintel
and columns and fasten with bolts.
4 4
4 Position
4 4
rear frame assemblyrear frame assembly
rear frame assembly
rear frame assemblyrear frame assembly
across top of main wall panels and fasten using screws.
5 5
5 Fasten
5 5
side top anglesside top angles
side top angles to the
side top anglesside top angles
corner panels using screws. Fasten support column to top angle using a bolt.
6 6
6 Position
6 6
door trackdoor track
door track to the inside of
door trackdoor track
side top angle, butted up against sup­port column. With short flange of track at bottom, fasten angle to track using 4 screws at the 2nd, 3rd, 4th and 5th hole in from support column. See Step 12 for rear door installation.
STEP
44
4
44
2 HOLES
LONG
FLANGE
SHORT FLANGE
SIDE TOP
ANGLE
TRACK
2 HOLES
INSIDE
STEP
STEP
66
6
66
7835
8532
8531
7838
#8Ax5/16" Screw
FACING INSIDE
STEP
7831 STEP
33
3
33
STEP
79587834
11
1
11
#10-32x7/16" Bolt
7839
#10-32 Square Nut
FRONT OF BUILDING
22
2
22
7839
22
INSIDE
55
5
55
Page 23
Step 10Step 10
Step 10
Step 10Step 10
BW23
● Parts Needed For ●
FramesFrames
Frames
FramesFrames
12x17, 12x24 & 12x31 12x17, 12x24 & 12x31
12x17, 12x24 & 12x31
12x17, 12x24 & 12x31 12x17, 12x24 & 12x31
●●
7839 Front Column (2) 7839 Front Column (2)
●
7839 Front Column (2)
●●
7839 Front Column (2) 7839 Front Column (2)
●●
7834 Right Front Frame (1) 7834 Right Front Frame (1)
●
7834 Right Front Frame (1)
●●
7834 Right Front Frame (1) 7834 Right Front Frame (1)
●●
7835 Left Front Frame (1) 7835 Left Front Frame (1)
●
7835 Left Front Frame (1)
●●
7835 Left Front Frame (1) 7835 Left Front Frame (1)
●●
7831 Lintel (1) 7831 Lintel (1)
●
7831 Lintel (1)
●●
7831 Lintel (1) 7831 Lintel (1)
●●
Rear Frame Assembly (1) Rear Frame Assembly (1)
●
Rear Frame Assembly (1)
●●
Rear Frame Assembly (1) Rear Frame Assembly (1)
●●
7915 Side Top Angle (see below) 7915 Side Top Angle (see below)
●
7915 Side Top Angle (see below)
●●
7915 Side Top Angle (see below) 7915 Side Top Angle (see below)
●●
7838 Side Top Angle (2) 7838 Side Top Angle (2)
●
7838 Side Top Angle (2)
●●
7838 Side Top Angle (2) 7838 Side Top Angle (2)
●●
7958 Door Track (1) 7958 Door Track (1)
●
7958 Door Track (1)
●●
7958 Door Track (1) 7958 Door Track (1)
The top frame pieces give rigidity to the side walls and provide a surface for attaching the gables which sup­port the roof.
1 1
1 Fasten
1 1
front columns front columns
front columns to the bot-
front columns front columns
tom and mid front frames with bolts and nuts. Flange with 2 holes at each end must be facing outside. Fold front panel slightly away from column to tighten bolts and nuts.
2 2
2 Fasten
2 2
right right
right and
right right
left front frame left front frame
left front frame
left front frame left front frame
to the top of front wall panels using 4 screws.
3 3
3 Position
3 3
lintel lintel
lintel across top of frames
lintel lintel
and columns and fasten with bolts.
4 4
4 Position
4 4
rear frame assemblyrear frame assembly
rear frame assembly
rear frame assemblyrear frame assembly
across top of main wall panels and fasten using screws.
IF YOU ARE BUILDING A 12x24 Repeat side top angle assembly using 2 additional angles 7915.
IF YOU ARE BUILDING A 12x31 Repeat side top angle assembly using 4 additional angles 7915.
STEP
33
3
33
SIDE TOP
ANGLE
5 5
5 Fasten
5 5
side top angles 7915side top angles 7915
side top angles 7915 to
side top angles 7915side top angles 7915
the truss column using a screw and to rear corner panels using screws.
6 6
6 Fasten
6 6
under
7915 7915
7915 and fasten to front corner
7915 7915
side top angles 7838side top angles 7838
side top angles 7838
side top angles 7838side top angles 7838
panels using screws. Fasten over­lap (2 1/2" 6cm) with 2 bolts and nuts. Side angles overlap front and rear frames in the corners. Fasten sup­port column to side top angle using a bolt and nut.
7 7
7 Position
7 7
door trackdoor track
door track to the inside of
door trackdoor track
side top angle, butted up against sup­port column. With short flange of track at bottom, fasten angle to track using 4 screws at the 2nd, 3rd, 4th and 5th hole in from support column. See Step 12 for rear door installation.
2 HOLES
STEP
22
2
22
7834
INSIDE
7838
#10-32 Square Nut
7831
STEP
33
3
33
7839
STEP
11
1
11
7839
7835
LONG
FLANGE
SHORT
FLANGE
7915
FRONT OF BUILDING
TRACK
STEP
STEP
44
4
44
8532
7958
#8Ax5/16" Screw
66
6
66
STEP
FACING INSIDE
55
5
55
8531
STEP
77
7
77
2 HOLES
#10-32 x7/16" Bolt
INSIDE
23
Page 24
Step 11Step 11
Step 11
Step 11Step 11
BW24
● Parts Needed For ●
WW
W
WW
alls alls
alls
alls alls
All SizAll Siz
All Siz
All SizAll Siz
eses
es
eses
●●
7822 Main Wall Panel (see below) 7822 Main Wall Panel (see below)
●
7822 Main Wall Panel (see below)
●●
7822 Main Wall Panel (see below) 7822 Main Wall Panel (see below)
●●
7823 Medium Wall Panel (1) 7823 Medium Wall Panel (1)
●
7823 Medium Wall Panel (1)
●●
7823 Medium Wall Panel (1) 7823 Medium Wall Panel (1)
Each wall panel has a crimped rib on 1 side. The crimped rib should go under the rib of the panel that follows it. Leave out 1 main wall panel at the side or rear entry door location.
1 1
1 Fasten the
1 1
top and bottom with screws.
2 2
2 Fasten center of each panel to the
2 2
mid frames with screws. Fasten over­lapping ribs using 2 screws and a bolt with nut at the center.
3 3
3 At the rear center of the building,
3 3
fasten the same manner.
main wall panelsmain wall panels
main wall panels at the
main wall panelsmain wall panels
medium wall panel medium wall panel
medium wall panel in the
medium wall panel medium wall panel
Crimped Rib Underneath
IF YOU ARE BUILDING A 12x24 Install 3 additional main wall panels on each side of the building.
IF YOU ARE BUILDING A 12x31 Install 6 additional main wall panels on each side of the building.
STEP
33
3
33
7823
24
SCREWS TO FRAME
WIDE RIB
SCREWS TO
SCREWS TO FRAME
MEDIUM WALL PANELMEDIUM WALL PANEL
MEDIUM WALL PANEL
MEDIUM WALL PANELMEDIUM WALL PANEL
NARROW RIB (HAS BEAD)
FRAME
BOLT TO
PANEL
SCREW TO RIB
SCREW TO RIB
#10-32 Square Nut
7822
STEP
11
1
11
#10-32x7/16" Screw
Washer
#8Ax5/16" Screw
At the truss columns, fasten rib with bolt, washer & nut before screws are installed.
Detail Showing
Center of Panel Screwed
to Side Frame
STEP
22
2
22
Bolt and nut does not go thru side frame at overlap
Page 25
Step 12Step 12
Step 12
Step 12Step 12
BW25
Using the previous side entry door steps and this illustration, you can install the entry door at 2 locations along the rear wall. Whichever you choose, the door will always slide towards the corner of the building.
Rear EntrRear Entr
Rear Entr
Rear EntrRear Entr
● Parts Needed For ●
y Door y Door
y Door
y Door y Door
All SizAll Siz
All Siz
All SizAll Siz
eses
es
eses
●●
7517 Lower Door Track (1) 7517 Lower Door Track (1)
●
7517 Lower Door Track (1)
●●
7517 Lower Door Track (1) 7517 Lower Door Track (1)
●●
7560 Ramp (1) 7560 Ramp (1)
●
7560 Ramp (1)
●●
7560 Ramp (1) 7560 Ramp (1)
●●
8530 Splice Channel (1) 8530 Splice Channel (1)
●
8530 Splice Channel (1)
●●
8530 Splice Channel (1) 8530 Splice Channel (1)
●●
7951 Support Column (1) 7951 Support Column (1)
●
7951 Support Column (1)
●●
7951 Support Column (1) 7951 Support Column (1)
●●
7958 Door Track (1) 7958 Door Track (1)
●
7958 Door Track (1)
●●
7958 Door Track (1) 7958 Door Track (1)
11
1Install
11
using 1/4" bolts and nuts.
22
2Fasten
22
down, to rear frame and to
column column
column using bolts and nuts, and to
column column
wall panel using screws. Fasten sup­port column to rear frames using bolts and nuts. Fold rear wall panel slightly away from column to tighten bolts and nuts.
33
3Position
33
the rear frame, butted up against sup­port column. With short flange of track at bottom, fasten frame to track using 4 screws at the 2nd, 3rd, 4th and 5th hole in from support column.
lower door track lower door track
lower door track and
lower door track lower door track
splice channel, splice channel,
splice channel, upside
splice channel, splice channel,
supportsupport
support
supportsupport
door track door track
door track to the inside of
door track door track
7948
Step 13
rampramp
ramp
rampramp
7958
STEP
33
3
33
7951
STEP
22
2
22
8530
7517
STEP
11
1
11
7560
INSIDE OF
BUILDING
INSIDE
25
Page 26
Step 13Step 13
Step 13
Step 13Step 13
Side or Rear EntrSide or Rear Entr
Side or Rear Entr
BW26
The door jambs reinforce the door opening and provide an attractive trim. Follow these steps for both door jambs.
Side or Rear EntrSide or Rear Entr
● Parts Needed For ●
y Door y Door
y Door
y Door y Door
All SizAll Siz
All Siz
All SizAll Siz
●●
7946 Door Jamb (2) 7946 Door Jamb (2)
●
7946 Door Jamb (2)
●●
7946 Door Jamb (2) 7946 Door Jamb (2)
●●
7948 Door Wall Brace (1) 7948 Door Wall Brace (1)
●
7948 Door Wall Brace (1)
●●
7948 Door Wall Brace (1) 7948 Door Wall Brace (1)
●●
7972 Door Handle Lock Bracket (1) 7972 Door Handle Lock Bracket (1)
●
7972 Door Handle Lock Bracket (1)
●●
7972 Door Handle Lock Bracket (1) 7972 Door Handle Lock Bracket (1)
eses
es
eses
11
1Place
11
panel in the direction of sliding door. Fasten panel to brace using screws.
22
2Overlap rib of wall panel with a
22
door jamb door jamb
door jamb and fasten at top to angle,
door jamb door jamb
middle to brace, and bottom to frame using #6Ax7/8" screws and spacers. Position spacer inside wall panel rib.
33
3Fasten outer flange of door jamb to
33
wall panel using 3 screws.
44
4Secure the
44
bracket bracket
bracket to the opposite door jamb at
bracket bracket
the middle hole with a (no slot) bolt.
door wall brace door wall brace
door wall brace behind wall
door wall brace door wall brace
door handle lockdoor handle lock
door handle lock
door handle lockdoor handle lock
Inside of Building
STEP
22
2
22
Direction of Sliding Door
Remove and reinset screws from panel
26
STEP
11
1
11
#8Ax5/16" Screw
7948
STEP
33
3
33
7946
7946
#6Ax7/8" Screw
7972
STEP
44
4
44
#10-32x7/16" (No Slot) Bolt
Page 27
Step 14Step 14
Step 14
Step 14Step 14
BW27
● Parts Needed For ●
TT
rr
acac
T
TT
k Suppork Suppor
r
ac
k Suppor
rr
acac
k Suppork Suppor
ts ts
ts
ts ts
All SizAll Siz
All Siz
All SizAll Siz
eses
es
eses
●●
7840 Right Track Support (1) 7840 Right Track Support (1)
●
7840 Right Track Support (1)
●●
7840 Right Track Support (1) 7840 Right Track Support (1)
●●
7841 Left Track Support (1) 7841 Left Track Support (1)
●
7841 Left Track Support (1)
●●
7841 Left Track Support (1) 7841 Left Track Support (1)
11
1Fasten
11
ports ports
ports to the front columns using 5
ports ports
bolts from the inside and nuts out­side.
Flanges on track supports
face
right right
right and
right right
NOTENOTE
NOTE
NOTENOTE
towards front of building.
left track sup-left track sup-
left track sup-
left track sup-left track sup-
#10-32x7/16" Bolt
must
Step 15Step 15
Step 15
Step 15Step 15
11
1Position Truss Assembly on build-
11
ing by sliding truss upper chords over truss columns and fasten with 6 bolts and nuts on each side.
TT
T
TT
● Parts Needed For ●
rr
uss 12x17,uss 12x17,
r
uss 12x17,
rr
uss 12x17,uss 12x17,
12x24 & 12x31 12x24 & 12x31
12x24 & 12x31
12x24 & 12x31 12x24 & 12x31
●●
Truss Assembly (see below) Truss Assembly (see below)
●
Truss Assembly (see below)
●●
Truss Assembly (see below) Truss Assembly (see below)
IF YOU ARE BUILDING A 12x24 Install 2 trusses on truss columns IF YOU ARE BUILDING A 12x31 Install 3 trusses on truss columns
27
Page 28
Step 16Step 16
Step 16
Step 16Step 16
BW28
● Parts Needed For ●
Roof Beams 12x17, 12x24 & 12x31Roof Beams 12x17, 12x24 & 12x31
Roof Beams 12x17, 12x24 & 12x31
Roof Beams 12x17, 12x24 & 12x31Roof Beams 12x17, 12x24 & 12x31
●●
Right Gable Assembly (1) Right Gable Assembly (1)
●
Right Gable Assembly (1)
●●
Right Gable Assembly (1) Right Gable Assembly (1)
●●
7833 Roof Beam (4) 7833 Roof Beam (4)
●
7833 Roof Beam (4)
●●
7833 Roof Beam (4) 7833 Roof Beam (4)
●●
Left Gable Assembly (1) Left Gable Assembly (1)
●
Left Gable Assembly (1)
●●
Left Gable Assembly (1) Left Gable Assembly (1)
●●
6382 Center Gable Brace (1) 6382 Center Gable Brace (1)
●
6382 Center Gable Brace (1)
●●
6382 Center Gable Brace (1) 6382 Center Gable Brace (1)
●●
7833 Roof Beam Assembly (1) 7833 Roof Beam Assembly (1)
●
7833 Roof Beam Assembly (1)
●●
7833 Roof Beam Assembly (1) 7833 Roof Beam Assembly (1)
●●
6372 Gable Strut (2) 6372 Gable Strut (2)
●
6372 Gable Strut (2)
●●
6372 Gable Strut (2) 6372 Gable Strut (2)
11
1Lift and fasten a right gable assem-
11
bly at top of lintel using bolts & screws.
22
2Install single
22
the gable braces at the front section.
33
3Lift and fasten a left gable assem-
33
bly in the same manner.
44
4Join left and right gables together
44
with a bolts and nuts, at middle holes.
55
5Apply
55
mating edge of the left and right gables as shown. Cut the weather stripping to length.
center gable brace center gable brace
center gable brace using 3
center gable brace center gable brace
weather stripping weather stripping
weather stripping along the
weather stripping weather stripping
roof beams 7833 roof beams 7833
roof beams 7833 to
roof beams 7833 roof beams 7833
66
6Install single roof beams to the left
66
side of building in the same manner. Slide a over center gable flange and other end over center gable braces on truss and fasten using bolts & nuts.
77
7Fasten a
77
roof beam behind the front gable by placing tab on end of strut roof beams. Align the tab with holes and fasten strut with 2 bolts.
88
8Fasten the lower end of the strut to
88
center gable flange with 2 bolts.
99
9At the truss assembly the gable struts
99
are attached between the middle roof beam and center brace.
roof beam assembly 7833roof beam assembly 7833
roof beam assembly 7833
roof beam assembly 7833roof beam assembly 7833
gable strut gable strut
gable strut to the middle
gable strut gable strut
between
the
STEP
33
3
33
STEP
STEP
44
4
44
STEP
11
1
11
STEP
66
6
66
STEP
22
2
22
NOTENOTE
NOTE
NOTENOTE
Do not tighten bolts and nuts
until all struts are assembled.
STEP
77
7
77
STEP
88
8
88
STEP
99
9
99
28
55
5
55
Page 29
Step 17Step 17
Step 17
Step 17Step 17
BW29
11
1Fasten gables to rear frame using
11
all screws.
Roof Beams 12x17, 12x24 & 12x31Roof Beams 12x17, 12x24 & 12x31
Roof Beams 12x17, 12x24 & 12x31
Roof Beams 12x17, 12x24 & 12x31Roof Beams 12x17, 12x24 & 12x31
● Parts Needed For ●
●●
Right Gable Assembly (1) Right Gable Assembly (1)
●
Right Gable Assembly (1)
●●
Right Gable Assembly (1) Right Gable Assembly (1)
●●
Left Gable Assembly (1) Left Gable Assembly (1)
●
Left Gable Assembly (1)
●●
Left Gable Assembly (1) Left Gable Assembly (1)
●●
7912 Roof Beam (4) 7912 Roof Beam (4)
●
7912 Roof Beam (4)
●●
7912 Roof Beam (4) 7912 Roof Beam (4)
●●
6382 Center Gable Brace (1) 6382 Center Gable Brace (1)
●
6382 Center Gable Brace (1)
●●
6382 Center Gable Brace (1) 6382 Center Gable Brace (1)
●●
7912 Roof Beam Assembly (1) 7912 Roof Beam Assembly (1)
●
7912 Roof Beam Assembly (1)
●●
7912 Roof Beam Assembly (1) 7912 Roof Beam Assembly (1)
●●
6372 Gable Strut (2) 6372 Gable Strut (2)
●
6372 Gable Strut (2)
●●
6372 Gable Strut (2) 6372 Gable Strut (2)
22
2Install single
22
center gable brace the same manner.
33
3Fasten
33
and struts as before.
44
4Fasten
44
ing.
roof beams 7912 roof beams 7912
roof beams 7912 and
roof beams 7912 roof beams 7912
to rear section in
roof beam assembly 7912roof beam assembly 7912
roof beam assembly 7912
roof beam assembly 7912roof beam assembly 7912
gable strut gable strut
gable strut to rear of build-
gable strut gable strut
STEP
33
3
33
STEP
22
2
22
STEP
11
1
11
STEP
44
4
44
29
Page 30
Step 18Step 18
Step 18
Step 18Step 18
BW30
11
1Lift and fasten a right gable as-
11
sembly at top of lintel using bolts & screws.
22
2Lift and fasten a left gable assem-
22
bly at top of rear frame using screws.
33
3Install single
33
braces using bolts and nuts.
44
4Fasten gables to left side of build-
44
ing in the same manner.
roof beams roof beams
roof beams to gable
roof beams roof beams
● Parts Needed For ●
Roof Beams 12x10Roof Beams 12x10
Roof Beams 12x10
Roof Beams 12x10Roof Beams 12x10
55
5Join left and right gables together
55
with a bolts and nuts, at middle holes.
66
6Apply
66
the mating edge of the left and right gables as shown. Cut the weather stripping to length.
77
7Install single roof beams to the
77
left side of building in the same manner. Slide a
sembly sembly
sembly over center gable flange
sembly sembly
and fasten.
center gable brace center gable brace
center gable brace using 3
center gable brace center gable brace
weather stripping weather stripping
weather stripping along
weather stripping weather stripping
roof beam as-roof beam as-
roof beam as-
roof beam as-roof beam as-
●●
Right Gable Assembly (2) Right Gable Assembly (2)
●
Right Gable Assembly (2)
●●
Right Gable Assembly (2) Right Gable Assembly (2)
●●
Left Gable Assembly (2) Left Gable Assembly (2)
●
Left Gable Assembly (2)
●●
Left Gable Assembly (2) Left Gable Assembly (2)
●●
6382 Center Gable Brace (2) 6382 Center Gable Brace (2)
●
6382 Center Gable Brace (2)
●●
6382 Center Gable Brace (2) 6382 Center Gable Brace (2)
●●
7833 Roof Beam (4) 7833 Roof Beam (4)
●
7833 Roof Beam (4)
●●
7833 Roof Beam (4) 7833 Roof Beam (4)
●●
7833 Roof Beam Assembly (1) 7833 Roof Beam Assembly (1)
●
7833 Roof Beam Assembly (1)
●●
7833 Roof Beam Assembly (1) 7833 Roof Beam Assembly (1)
●●
6372 Gable Strut (2) 6372 Gable Strut (2)
●
6372 Gable Strut (2)
●●
6372 Gable Strut (2) 6372 Gable Strut (2)
88
8Fasten a
88
roof beam behind the front gable by placing tab on end of strut the roof beams. Align the tab with holes and fasten strut with 2 bolts.
99
9Fasten the lower end of the strut to
99
center gable flange with 2 bolts.
Do not tighten bolts and nuts
until the strut is assembled at rear
1010
10Repeat Steps 8 & 9 for rear of
1010
building.
gable strut gable strut
gable strut to the middle
gable strut gable strut
between
NOTENOTE
NOTE
NOTENOTE
STEP
44
4
44
STEP
66
6
66
STEP
55
5
55
STEP
99
9
99
STEP
88
8
88
STEP
11
1
11
STEP
77
7
77
STEP
33
3
33
STEP
1010
10
1010
STEP
22
2
22
30
Page 31
Step 19Step 19
Step 19
Step 19Step 19
BW31
11
1Square the building on the founda-
11
tion and at the top, by measuring diagonally from corner to corner as previously done.
22
2Use string to check and see if the
22
sides and rear of building are straight, not bowed inward or outward.
33
3Level the full perimeter of the floor
33
frame. Shim under with wood shin­gles if necessary.
44
4Square the front of building as pre-
44
viously done for base.
SquarSquar
Squar
SquarSquar
ing the Building ing the Building
ing the Building
ing the Building ing the Building
NOTENOTE
NOTE
NOTENOTE
The 95" (2,41m) door opening
must be held for proper door
alignment. Measure between
the left and right track support.
All SizAll Siz
All Siz
All SizAll Siz
eses
es
eses
55
5Anchor front frame to concrete with
55
1/4" diameter expandable anchor bolts or other means, where shown.
STEP
44
4
44
STEP
33
3
33
STEP
55
5
55
(2,41m)
STEP
11
1
11
(2,41m)
STEP
22
2
22
31
Page 32
Step 20Step 20
Step 20
Step 20Step 20
BW32
CorCor
Cor
CorCor
● Parts Needed For ●
ner Roof Pner Roof P
ner Roof P
ner Roof Pner Roof P
anels anels
anels
anels anels
All SizAll Siz
All Siz
All SizAll Siz
eses
es
eses
●●
7826 Right Roof Panel (2) 7826 Right Roof Panel (2)
●
7826 Right Roof Panel (2)
●●
7826 Right Roof Panel (2) 7826 Right Roof Panel (2)
●●
7827 Left Roof Panel (1) 7827 Left Roof Panel (1)
●
7827 Left Roof Panel (1)
●●
7827 Left Roof Panel (1) 7827 Left Roof Panel (1)
Installing the roof panels is best done with a step ladder. Each screw and bolt in the roof requires a washer. Support lintel by propping up at cen­ter with a wood 2x4 until sag is gone and there are no buckles in gables.
11
1Position a
11
front left corner and fasten to the gable and roof beams using screws and bolts as shown.
lower end of the panels to the side top angle at this time.
Hint: Hint:
Hint: Follow the fastener sequence
Hint: Hint:
shown, for proper alignment.
right roof panel right roof panel
right roof panel at the
right roof panel right roof panel
Do not fasten the
22
2Install the
22
side in the position shown. Remove lintel support.
33
3Temporarily install a second right
33
roof panel loosely as shown, for re­moval later. Do not fasten left rear panel at this time.
left roof panel left roof panel
left roof panel for the right
left roof panel left roof panel
STEP
11
1
11
FRONTFRONT
FRONT
FRONTFRONT
LEFT CORNER ROOF PANEL
STEP
22
2
22
NOTENOTE
NOTE
NOTENOTE
If roof beam holes do not line up
with the roof panel holes, shift the
building from left to right.
If this does not help, your building
may not be level. Shim the
corners until holes line up.
STEP
33
3
33
RIGHT CORNER ROOF PANEL
32
Page 33
Step 21Step 21
Step 21
Step 21Step 21
BW33
● Parts Needed For ●
Roof Panels 12x10Roof Panels 12x10
Roof Panels 12x10
Roof Panels 12x10Roof Panels 12x10
●●
7828 Middle Roof Panel (2) 7828 Middle Roof Panel (2)
●
7828 Middle Roof Panel (2)
●●
7828 Middle Roof Panel (2) 7828 Middle Roof Panel (2)
11
1Position
11
lapping rib of left corner roof panel. Fasten overlap at center of roof panel rib using a bolt and nut. Fasten to roof beams as before using screws.
22
2Cut the
22
into 4 strips, each strip being about 2" (5cm) long.
33
3Cover the joint at the peak with
33
weather stripping tape. Unroll the tape and press it down over the opening at the ridge as you install each roof panel. Do not cut the tape at this time.
middle roof panel middle roof panel
middle roof panel over-
middle roof panel middle roof panel
weather stripping tapeweather stripping tape
weather stripping tape
weather stripping tapeweather stripping tape
STEP
44
4
44
STEP
44
4Install a middle roof panel on the
44
left side of building. At the top roof beam end of panels, fasten 1st roof panel rib overlaps with a bolt and nut. Press 2 strips over the bolt heads. Save the other 2 strips for the next overlap. Remember, the crimped rib is always overlapped by wide rib of adjacent panel.
33
3
33
STEP
11
1
11
33
Page 34
Step 22Step 22
Step 22
Step 22Step 22
BW34
● Parts Needed For ●
Roof Panels 12x17, 12x24 & 12x31Roof Panels 12x17, 12x24 & 12x31
Roof Panels 12x17, 12x24 & 12x31
Roof Panels 12x17, 12x24 & 12x31Roof Panels 12x17, 12x24 & 12x31
●●
7828 Middle Roof Panel 7828 Middle Roof Panel
●
7828 Middle Roof Panel
●●
7828 Middle Roof Panel 7828 Middle Roof Panel
(see below)(see below)
(see below)
(see below)(see below)
11
1Position
11
lapping rib of left corner roof panel. Fasten overlap at center of roof panel rib using a bolt and nut. Fasten to roof beams as before using screws.
22
2Cut the
22
into 8 strips, each strip being about 2" (5cm) long.
33
3Cover the joint at the peak with
33
weather stripping tape. Unroll the tape and press it down over the opening at the ridge as you install each roof panel. Do not cut the tape at this time.
44
4Install a middle roof panel on the
44
left side of building. At the top roof beam end of panels, fasten 1st roof panel rib overlaps with a bolt and nut. Press 2 strips over the bolt heads.
middle roof panel middle roof panel
middle roof panel over-
middle roof panel middle roof panel
weather stripping tapeweather stripping tape
weather stripping tape
weather stripping tapeweather stripping tape
IF YOU ARE BUILDING A 12x24 Cut 12 2" (5cm) strips. There are 3 extra middle roof panels on each side of building. Fasten 7th and 8th panel overlap and apply strip over head of bolt, along with ridge caps.
IF YOU ARE BUILDING A 12x31 Cut 16 2" (5cm) strips. There are 6 extra middle roof panels on each side of building. Fasten 7th, 8th, 10th & 11th panel overlap and apply strip over head of bolt, along with ridge caps.
Save the other strips for the 2nd, 4th and 5th overlaps. Remember, the crimped rib is always overlapped by wide rib of adjacent panel. Repeat procedure with 2 more middle roof panels working side to side.
34
STEP
44
4
44
STEP
11
1
11
STEP
33
3
33
Page 35
Step 23Step 23
Step 23
Step 23Step 23
BW35
11
1Temporarily remove right rear roof
11
panel.
● Parts Needed For ●
Ridge Caps 12x10Ridge Caps 12x10
Ridge Caps 12x10
Ridge Caps 12x10Ridge Caps 12x10
●●
7828 Middle Roof Panel (2) 7828 Middle Roof Panel (2)
●
7828 Middle Roof Panel (2)
●●
7828 Middle Roof Panel (2) 7828 Middle Roof Panel (2)
●●
7843 Ridge Cap (1) 7843 Ridge Cap (1)
●
7843 Ridge Cap (1)
●●
7843 Ridge Cap (1) 7843 Ridge Cap (1)
●●
7827 Left Roof Panel (1) 7827 Left Roof Panel (1)
●
7827 Left Roof Panel (1)
●●
7827 Left Roof Panel (1) 7827 Left Roof Panel (1)
●●
6874 Ridge Cap (1) 6874 Ridge Cap (1)
●
6874 Ridge Cap (1)
●●
6874 Ridge Cap (1) 6874 Ridge Cap (1)
22
2Install 2
22
ten 2nd roof panel rib overlaps with a bolt and nut. Press 2 strips over the bolt heads. Continue weather strip­ping.
33
3Install the
33
els els
els at the rear gables. Follow fas-
els els
tener sequence.
44
4Position a
44
completed front roof section.
55
5Install the second
55
overlapping the first ridge cap. Align the holes and fasten using bolts.
66
6Fasten the lower end of the panels
66
to the side top angle using screws.
middle roof panels. middle roof panels.
middle roof panels. Fas-
middle roof panels. middle roof panels.
right right
right and
right right
ridge cap 7843 ridge cap 7843
ridge cap 7843 on the
ridge cap 7843 ridge cap 7843
left roof pan-left roof pan-
left roof pan-
left roof pan-left roof pan-
ridge cap 6874ridge cap 6874
ridge cap 6874
ridge cap 6874ridge cap 6874
STEP
STEP
11
1
11
STEP
55
5
55
STEP
33
3
33
44
4
44
STEP
66
6
66
STEP
22
2
22
35
Page 36
Step 24Step 24
Step 24
Step 24Step 24
BW36
● Parts Needed For ●
Ridge Caps 12x17, 12x24 & 12x31Ridge Caps 12x17, 12x24 & 12x31
Ridge Caps 12x17, 12x24 & 12x31
Ridge Caps 12x17, 12x24 & 12x31Ridge Caps 12x17, 12x24 & 12x31
●●
7828 Middle Roof Panel (see below) 7828 Middle Roof Panel (see below)
●
7828 Middle Roof Panel (see below)
●●
7828 Middle Roof Panel (see below) 7828 Middle Roof Panel (see below)
●●
7843 Ridge Cap (see below) 7843 Ridge Cap (see below)
●
7843 Ridge Cap (see below)
●●
7843 Ridge Cap (see below) 7843 Ridge Cap (see below)
●●
7827 Left Roof Panel (1) 7827 Left Roof Panel (1)
●
7827 Left Roof Panel (1)
●●
7827 Left Roof Panel (1) 7827 Left Roof Panel (1)
●●
6874 Ridge Cap (1) 6874 Ridge Cap (1)
●
6874 Ridge Cap (1)
●●
6874 Ridge Cap (1) 6874 Ridge Cap (1)
11
1Continue weather stripping and fas-
11
tening overlaps.
22
2Position a
22
completed front roof section.
33
3Install 2
33 44
4Install the second
44
overlapping the first ridge cap. Align the holes and fasten using bolts.
55
5Temporarily remove right rear roof
55
panel. Install 4 As each panel is fastened, carefully raise 2nd ridge cap slightly away from panels for fasteners and tape.
ridge cap 7843 ridge cap 7843
ridge cap 7843 on the
ridge cap 7843 ridge cap 7843
middle roof panels.middle roof panels.
middle roof panels.
middle roof panels.middle roof panels.
ridge cap 7843ridge cap 7843
ridge cap 7843
ridge cap 7843ridge cap 7843
middle roof panels.middle roof panels.
middle roof panels.
middle roof panels.middle roof panels.
66
6Install the
66
panels panels
panels at the rear gables. Follow
panels panels
fastener sequence.
77
7Install the third
77
overlapping the second ridge cap. Align the holes and fasten using bolts.
88
8Fasten the lower end of the pan-
88
els to the side top angle using screws.
right right
right and
right right
ridge cap 6874ridge cap 6874
ridge cap 6874
ridge cap 6874ridge cap 6874
left roofleft roof
left roof
left roofleft roof
IF YOU ARE BUILDING A 12x24 Replace ridge cap 6874 with an additional ridge cap 7843 and install ridge cap 6874 to rear of building.
STEP
55
5
55
STEP
77
7
77
STEP
11
1
11
STEP
66
6
66
STEP
44
4
44
STEP
22
2
22
IF YOU ARE BUILDING A 12x31 Replace ridge cap 6874 with 2 additional ridge caps 7843 and install ridge cap 6874 to rear of building.
STEP
33
3
33
STEP
88
8
88
36
Page 37
Step 25Step 25
Step 25
Step 25Step 25
BW37
● Parts Needed For ●
TT
rr
im 12x10im 12x10
T
r
im 12x10
TT
rr
im 12x10im 12x10
●●
5220 Side Roof Trim (2) 5220 Side Roof Trim (2)
●
5220 Side Roof Trim (2)
●●
5220 Side Roof Trim (2) 5220 Side Roof Trim (2)
●●
6014 Side Roof Trim (2) 6014 Side Roof Trim (2)
●
6014 Side Roof Trim (2)
●●
6014 Side Roof Trim (2) 6014 Side Roof Trim (2)
●●
7846 Right Rake (2) 7846 Right Rake (2)
●
7846 Right Rake (2)
●●
7846 Right Rake (2) 7846 Right Rake (2)
●●
7845 Left Rack (2) 7845 Left Rack (2)
●
7845 Left Rack (2)
●●
7845 Left Rack (2) 7845 Left Rack (2)
11
1Attach the
11
lower end of the roof panels on each side of the building using screws at each panel overlap.
A single screw fastens both trim
pieces at the overlap.
22
2Position
22
ends of roof, noting that rake slips under ridge cap, but fits on top of side roof trim. Fasten rake to the center of roof panel rib using a bolt.
side roof trim side roof trim
side roof trim to the
side roof trim side roof trim
NOTENOTE
NOTE
NOTENOTE
left left
left and
left left
right rake right rake
right rake to the
right rake right rake
33
3Fasten roof panel rib, rake,
33
cap cap
cap and ridge cap together using bolts
cap cap
and nuts. Fasten remaining peak cap in the same manner.
44
4Using your thumb and index finger,
44
overbend the bottom flange of the side roof trim at the corner inward enough so the right and left roof trim caps fit onto right and left corners.
55
5Fasten rake to side trim using a screw
55
into roof panel.
66
6Fasten the roof trim caps to the side
66
trim using a screw.
peakpeak
peak
peakpeak
STEP
33
3
33
STEP
22
2
22
STEP
44
4
44
STEP
55
5
55
STEP
66
6
66
STEP
11
1
11
37
Page 38
Step 26Step 26
Step 26
Step 26Step 26
BW38
● Parts Needed For ●
TT
rr
im 12x17,im 12x17,
T
r
im 12x17,
TT
rr
im 12x17,im 12x17,
12x24 & 12x31 12x24 & 12x31
12x24 & 12x31
12x24 & 12x31 12x24 & 12x31
●●
5220 Side Roof Trim (see below) 5220 Side Roof Trim (see below)
●
5220 Side Roof Trim (see below)
●●
5220 Side Roof Trim (see below) 5220 Side Roof Trim (see below)
●●
6014 Side Roof Trim (2) 6014 Side Roof Trim (2)
●
6014 Side Roof Trim (2)
●●
6014 Side Roof Trim (2) 6014 Side Roof Trim (2)
●●
7845 Left Rack (2) 7845 Left Rack (2)
●
7845 Left Rack (2)
●●
7845 Left Rack (2) 7845 Left Rack (2)
●●
7846 Right Rake (2) 7846 Right Rake (2)
●
7846 Right Rake (2)
●●
7846 Right Rake (2) 7846 Right Rake (2)
11
1Attach the
11
lower end of the roof panels on each side of the building using screws at each panel overlap.
A single screw fastens both trim
pieces at the overlap.
22
2Position
22
ends of roof, noting that rake slips under ridge cap, but fits on top of side roof trim. Fasten rake to the center of roof panel rib using a bolt.
33
3Fasten roof panel rib, rake,
33
cap cap
cap and ridge cap together using
cap cap
bolts and nuts. Fasten remaining peak cap in the same manner.
side roof trim side roof trim
side roof trim to the
side roof trim side roof trim
NOTENOTE
NOTE
NOTENOTE
left left
left and
left left
right rake right rake
right rake to the
right rake right rake
peakpeak
peak
peakpeak
IF YOU ARE BUILDING A 12x24 Install additional side roof trim 5220 towards rear of building. IF YOU ARE BUILDING A 12x31 Install 2 additional side roof trim 5220 pieces towards rear of building.
44
4Using your thumb and index finger,
44
overbend the bottom flange of the side roof trim at the corner inward enough so the right and left roof trim caps fit onto right and left corners.
55
5Fasten rake to side trim using a
55
screw into roof panel.
66
6Fasten the roof trim caps to the side
66
trim using a screw.
STEP
33
3
33
STEP
55
5
55
STEP
11
1
11
STEP
STEP
22
2
22
44
4
44
STEP
66
6
66
38
Page 39
Step 27Step 27
Step 27
Step 27Step 27
BW39
NOTENOTE
NOTE
NOTENOTE
To assemble door to slide from
left to right (opening), position
door with handle holes on left side
of door. Position handle holes on
right side if door is to slide from
right to left (opening).
Each bolt and screw in the door re­quires a washer.
Side or Rear EntrSide or Rear Entr
Side or Rear Entr
Side or Rear EntrSide or Rear Entr
● Parts Needed For ●
y Door y Door
y Door
y Door y Door
All SizAll Siz
All Siz
All SizAll Siz
eses
es
eses
●●
7945 Door (1) 7945 Door (1)
●
7945 Door (1)
●●
7945 Door (1) 7945 Door (1)
●●
3719 Door Handle Brace (1) 3719 Door Handle Brace (1)
●
3719 Door Handle Brace (1)
●●
3719 Door Handle Brace (1) 3719 Door Handle Brace (1)
●●
7947 Vertical Door Brace (1) 7947 Vertical Door Brace (1)
●
7947 Vertical Door Brace (1)
●●
7947 Vertical Door Brace (1) 7947 Vertical Door Brace (1)
●●
6264 Horizontal Door Brace (2) 6264 Horizontal Door Brace (2)
●
6264 Horizontal Door Brace (2)
●●
6264 Horizontal Door Brace (2) 6264 Horizontal Door Brace (2)
11
1Attach the
11
handle handle
handle to the
handle handle
shown.
22
2Swing the door handle brace up to
22
the hole in the center of the door and insert a screw.
33
3Hold the
33
against the center of the inside sur­face of the door and turn the screw to hold the vertical door brace and door handle brace in place. Fasten to door above and below center connection using 2 screws.
44
4Insert a second bolt in the door
44
handle and tighten both bolts.
55
5Put a
55
the top edge fasten
door handle brace door handle brace
door handle brace and
door handle brace door handle brace
door door
door with 1 bolt as
door door
Don't tighten the bolt yet.
vertical door bracevertical door brace
vertical door brace
vertical door bracevertical door brace
horizontal door brace horizontal door brace
horizontal door brace onto
horizontal door brace horizontal door brace
and
bottom edge and
with 1 bolt in the center.
STEP
11
1
11
STEP
55
5
55
STEP
22
2
22
STEP
33
3
33
66
6Attach the
66
shown.
lower door guides lower door guides
lower door guides as
lower door guides lower door guides
STEP
66
6
66
STEP
44
4
44
39
Page 40
Step 28Step 28
Step 28
Step 28Step 28
BW40
● Parts Needed For ●
Side or Rear EntrSide or Rear Entr
Side or Rear Entr
Side or Rear EntrSide or Rear Entr
y Door y Door
y Door
y Door y Door
All SizAll Siz
All Siz
All SizAll Siz
eses
es
eses
●●
Door Assembly (1) Door Assembly (1)
●
Door Assembly (1)
●●
Door Assembly (1) Door Assembly (1)
11
1Position
11
from the end of door track, as shown in the end view.
22
2From inside the building, put the
22
bottom of the door behind door jamb into the lower door track.
33
3Position the top of the door so that
33
the holes in the door line up with the holes in the door slides.
44
4Fasten the door to the door slides
44
using a #10Bx1/2" screw.
The 4 holes in the top of door allow
door slides door slides
door slides onto the legs,
door slides door slides
NOTENOTE
NOTE
NOTENOTE
you to adjust the door.
Place the door slide in the
middle 2 holes.
STEP
33
3
33
STEP
44
4
44
STEP
11
1
11
STEP
22
2
22
40
Page 41
Step 29Step 29
Step 29
Step 29Step 29
BW41
● Parts Needed For ●
Bottom Section Roll-Up-DoorBottom Section Roll-Up-Door
Bottom Section Roll-Up-Door
Bottom Section Roll-Up-DoorBottom Section Roll-Up-Door
●●
9286 Door Panel (Bottom) (1) 9286 Door Panel (Bottom) (1)
●
9286 Door Panel (Bottom) (1)
●●
9286 Door Panel (Bottom) (1) 9286 Door Panel (Bottom) (1)
●●
7808 Bottom Angle (1) 7808 Bottom Angle (1)
●
7808 Bottom Angle (1)
●●
7808 Bottom Angle (1) 7808 Bottom Angle (1)
●●
8198 Vinyl Weatherstrip (1) 8198 Vinyl Weatherstrip (1)
●
8198 Vinyl Weatherstrip (1)
●●
8198 Vinyl Weatherstrip (1) 8198 Vinyl Weatherstrip (1)
11
1Layout the
11
surface, protecting the panels from being scratched.
22
2Bolt the middle stiles at the center
22
of the 3 door panels where indicated with #10-32x3/8" bolts on the outside and square nuts inside.
33
3On the
33
tion, tion,
tion, attach the
tion, tion, et et
et to the lower right corner and the
et et bottom bracket bottom bracket
bottom bracket to the left side using
bottom bracket bottom bracket
#10Bx1/2" truss head screws into end stiles.
44
4Loosely install
44
bottom section using #10-32x3/8" bolts and square nuts. Insert vinyl
weather strip weather strip
weather strip between angle and
weather strip weather strip
bottom section and tighten bolts.
door panels door panels
door panels on a flat
door panels door panels
door panel bottom sec-door panel bottom sec-
door panel bottom sec-
door panel bottom sec-door panel bottom sec-
right bottom brack-right bottom brack-
right bottom brack-
right bottom brack-right bottom brack-
leftleft
left
leftleft
bottom angle bottom angle
bottom angle to the
bottom angle bottom angle
STEP
11
1
11
STEP
66
6
66
STEP
55
5
55
STEP
22
2
22
55
5Fasten 2
55
tion, just below the bottom of middle stile using 1/4-20x1/2" hex head bolts and 1/4-20 square nuts.
66
6Install the
66
corners and to the middle stile of the bottom section using #10Bx1/2" truss head screws.
Be sure you fasten the lower part
of hinge to the top of each stile.
The top hinge leaf is marked.
lift handles lift handles
lift handles to bottom sec-
lift handles lift handles
#1 hinges #1 hinges
#1 hinges at the upper
#1 hinges #1 hinges
NOTENOTE
NOTE
NOTENOTE
STEP
44
4
44
STEP
33
3
33
41
Page 42
Step 30Step 30
Step 30
Step 30Step 30
BW42
● Parts Needed For ●
Lock Section Roll-Up-DoorLock Section Roll-Up-Door
Lock Section Roll-Up-Door
Lock Section Roll-Up-DoorLock Section Roll-Up-Door
●●
7848 Door Panel (Lock) (1) 7848 Door Panel (Lock) (1)
●
7848 Door Panel (Lock) (1)
●●
7848 Door Panel (Lock) (1) 7848 Door Panel (Lock) (1)
11
1With the key, unlock the outside
11
locking handle locking handle
locking handle and rotate the han-
locking handle locking handle
dle to a vertical position. Insert the square shank through the hole locat­ed in the center of
section. section.
section. Slide in the
section. section.
and insert the #10-32x2 1/2" flat head bolts through handle, spacer and stile. Secure with square nuts and tighten.
22
2Turn the locking handle to a hori-
22
zontal position. Slide the
bar spacer bar spacer
bar spacer over the square shank of
bar spacer bar spacer
the lock handle and slip the
bar bar
bar over shank. Secure with the
bar bar side "T" handle. side "T" handle.
side "T" handle. Tighten set screw
side "T" handle. side "T" handle.
in handle. Attach small holes on the flat latch bar. Slip oppo­site end of "S" hooks through
chains.chains.
chains.
chains.chains.
door panel lockdoor panel lock
door panel lock
door panel lockdoor panel lock
stile spacersstile spacers
stile spacers
stile spacersstile spacers
inside latchinside latch
inside latch
inside latchinside latch
flat latchflat latch
flat latch
flat latchflat latch
in-in-
in-
in-in-
"S" hooks "S" hooks
"S" hooks to
"S" hooks "S" hooks
latchlatch
latch
latchlatch
STEP
11
1
11
STEP
22
2
22
33
3Attach the
33
end stiles on the lock section. Attach "S" hooks to the holes on top of the latches. Attach the latch chains to the "S" hooks so that the chain is taut.
Hint: Hint:
Hint: If chain is too tight, latches will
Hint: Hint:
not engage strikes (on track) prop­erly. If chain is too loose, the lock handle will not retract latches. Adjust chains by changing the hole location of "S" hook through chain.
44
4Attach
44
the upper corners of end stiles. Fas­ten #1 hinge to the middle stile.
Hint: Hint:
Hint: When installing hinges, be sure
Hint: Hint:
the hinge number is always on the lower hinge leaf.
spring latches spring latches
spring latches to the
spring latches spring latches
#2 hinges #2 hinges
#2 hinges to lock section at
#2 hinges #2 hinges
STEP
44
4
44
STEP
33
3
33
42
Page 43
Step 31Step 31
Step 31
Step 31Step 31
BW43
NOTENOTE
NOTE
NOTENOTE
When rib neck bolts are inserted
in the track, use bolts with heads
located on the inner side of the
track to prevent interference with
the movement of the rollers.
VV
V
VV
erer
er
erer
● Parts Needed For ●
tical tical
tical
tical tical
TT
T
TT
rr
acac
ks Roll-Up-Doorks Roll-Up-Door
r
ac
ks Roll-Up-Door
rr
acac
ks Roll-Up-Doorks Roll-Up-Door
●●
67510 Right Vertical Track (1) 67510 Right Vertical Track (1)
●
67510 Right Vertical Track (1)
●●
67510 Right Vertical Track (1) 67510 Right Vertical Track (1)
●●
67509 Left Vertical Track (1) 67509 Left Vertical Track (1)
●
67509 Left Vertical Track (1)
●●
67509 Left Vertical Track (1) 67509 Left Vertical Track (1)
STEP
11
1
11
11
1Insert the
11
holes on the hinges furthest out from the face of the end stiles on both panels. Note that #1 hinge has only one barrel. Insert rollers through the tabs on the bottom brackets on bot­tom section.
22
2Attach
22
loosely to right and left track supports using 1/4-20x1/2" hex head bolts and square nuts.
33
3Attach spring latch
33
to vertical tracks using 1/4-20x1/2" rib neck bolts and square nuts.
44
4Lift the bottom section and insert
44
the rollers into the vertical tracks. Slide the panel down and level across top. Shim to level if necessary.
roller roller
roller shaft into the barrel
roller roller
right right
right and
right right
left vertical tracksleft vertical tracks
left vertical tracks
left vertical tracksleft vertical tracks
strikers strikers
strikers loosely
strikers strikers
STEP
22
2
22
STEP
33
3
33
55
5Insert lock section into vertical
55
tracks. Attach hinges from #1 to #2 panel by inserting #10Bx1/2" truss head screws at bottom edge of lock section. Do not fasten the last door panel at this time.
STEP
55
5
55
STEP
44
4
44
43
Page 44
Step 32Step 32
Step 32
Step 32Step 32
BW44
HorHor
Hor
HorHor
● Parts Needed For ●
iziz
ontal ontal
iz
ontal
iziz
ontal ontal
TT
T
TT
rr
acac
k Roll-Up-Doork Roll-Up-Door
r
ac
k Roll-Up-Door
rr
acac
k Roll-Up-Doork Roll-Up-Door
●●
7913 Spring Support Bracket (2) 7913 Spring Support Bracket (2)
●
7913 Spring Support Bracket (2)
●●
7913 Spring Support Bracket (2) 7913 Spring Support Bracket (2)
●●
67476 Right Horizontal Track (1) 67476 Right Horizontal Track (1)
●
67476 Right Horizontal Track (1)
●●
67476 Right Horizontal Track (1) 67476 Right Horizontal Track (1)
●●
67475 Left Horizontal Track (1) 67475 Left Horizontal Track (1)
●
67475 Left Horizontal Track (1)
●●
67475 Left Horizontal Track (1) 67475 Left Horizontal Track (1)
●●
7857 Truss Support (2) 7857 Truss Support (2)
●
7857 Truss Support (2)
●●
7857 Truss Support (2) 7857 Truss Support (2)
●●
7847 Door Panel (Top) (1) 7847 Door Panel (Top) (1)
●
7847 Door Panel (Top) (1)
●●
7847 Door Panel (Top) (1) 7847 Door Panel (Top) (1)
11
1Install
11
the roof beams using #10-32x7/16" bolts and #10-32 square nuts.
22
2Attach the
22
track track
track to right & left vertical track using
track track
bolts and nuts shown loosely.
33
3Fasten horizontal tracks loosely to
33
spring support brackets using 1/4­20x1/2" hex head bolts and 1/4-20 square nuts. Remove lower bolt at gable end of roof beam. Position
truss support truss support
truss support with 2" (5cm) flange
truss support truss support
against roof beam. Replace bolt to fasten support, brace and roof beam. Fasten opposite end to vertical track angle at the 3rd hole in from the end using #10-32x7/16" bolt and #10-32 square nut. Tighten all bolts and nuts.
spring support brackets spring support brackets
spring support brackets to
spring support brackets spring support brackets
right right
right and
right right
left horizontalleft horizontal
left horizontal
left horizontalleft horizontal
STEP
11
1
11
STEP
22
2
22
44
4Attach the
44
to the 3rd hole on the support angle of the horizontal track using 3/8 - 16 x 1 1/2" hex head bolt & 3/8-16 hex nut.
55
5Position third
55
tion tion
tion on second panel. Fasten top of
tion tion
hinges to bottom of third door panel using #10Bx1/2" truss head screws.
66
6Engage roller with
66
roller into horizontal track. Move as­sembly to line up with holes in end stile and fasten with #10Bx1/2" truss head screws.
STEP
sheave sheave
sheave (pulley wheel)
sheave sheave
door panel top sec-door panel top sec-
door panel top sec-
door panel top sec-door panel top sec-
top fixture, top fixture,
top fixture, slide
top fixture, top fixture,
66
6
66
STEP
33
3
33
STEP
44
4
44
44
STEP
55
5
55
Page 45
Step 33Step 33
Step 33
Step 33Step 33
BW45
CAUTION:CAUTION:
CAUTION:
CAUTION:CAUTION:
FROM THIS POINT ON, BE SUREFROM THIS POINT ON, BE SURE
FROM THIS POINT ON, BE SURE
FROM THIS POINT ON, BE SUREFROM THIS POINT ON, BE SURE
TO USE EXTREME CAUTIONTO USE EXTREME CAUTION
TO USE EXTREME CAUTION
TO USE EXTREME CAUTIONTO USE EXTREME CAUTION
UNTIL THE DOOR IS PROPERLYUNTIL THE DOOR IS PROPERLY
UNTIL THE DOOR IS PROPERLY
UNTIL THE DOOR IS PROPERLYUNTIL THE DOOR IS PROPERLY
SPRUNG AND OPERATINGSPRUNG AND OPERATING
SPRUNG AND OPERATING
SPRUNG AND OPERATINGSPRUNG AND OPERATING
11
1Attach
11
Fasten opposite ends of springs using a 3/8­16x1 1/2" hex head bolt and 3/8 nut. Attach spring assemblies to spring support brackets.
22
2Carefully raise the door to a fully
22
open position and prop. Make sure the door is level in the opening. Slip the keyed end of the over the studs of the bottom brackets. Thread cable over front sheave, around spring sheave and attach end
cable lacer. cable lacer.
to
cable lacer. Attach cable lacer
cable lacer. cable lacer.
with "S" hook in a convenient hole in horizontal track angle, keeping equal tension on both springs, so that door hangs level. Once cable is installed, remove prop and lower door.
"S" hooks "S" hooks
"S" hooks to both
"S" hooks "S" hooks
sheave sheave
sheave and
sheave sheave
spring clevis spring clevis
spring clevis to
spring clevis spring clevis
keyed cablekeyed cable
keyed cable
keyed cablekeyed cable
springs.springs.
springs.
springs.springs.
Roll-Up-DoorRoll-Up-Door
Roll-Up-Door
Roll-Up-DoorRoll-Up-Door
CHECKCHECK
CHECK
CHECKCHECK
Be sure that the lift cables do not rub and/or the rollers do not
bind in the track when door is opened or closed. Recheck the
springs to be sure that there is equal tension on both springs. This
is extremely important for proper door operation.
ADJUSTADJUST
ADJUST
ADJUSTADJUST
Springs by changing location of "S" hooks to another hole on
support angle of the horizontal track.
STEP
11
1
11
33
3Adjust vertical tracks so rollers seat
33
in "U" of track and bottom rollers fit snug against bottom brackets, but not too tight, so rollers will operate freely. When complete, tighten all track bolts.
44
4Adjust striker plates for proper en-
44
gagement with the latches. Adjust the top fixture up or down and tighten the screws to hold the third door panel against the lintel.
NOTENOTE
NOTE
NOTENOTE
Recheck all door fasteners and
hardware to be sure that each
fastener is tight and secure.
STEP
22
2
22
45
Page 46
Step 34Step 34
Step 34
Step 34Step 34
BW46
● Parts Needed For ●
FF
rr
ont Door Jont Door J
F
r
ont Door J
FF
rr
ont Door Jont Door J
ambs ambs
ambs
ambs ambs
All SizAll Siz
All Siz
All SizAll Siz
eses
es
eses
●●
7830 Right Door Jamb (1) 7830 Right Door Jamb (1)
●
7830 Right Door Jamb (1)
●●
7830 Right Door Jamb (1) 7830 Right Door Jamb (1)
●●
7829 Left Door Jamb (1) 7829 Left Door Jamb (1)
●
7829 Left Door Jamb (1)
●●
7829 Left Door Jamb (1) 7829 Left Door Jamb (1)
11
1Position
11
to right and left track supports with notched end on top, facing inside building.
22
2Fasten long flange to track support
22
and short flange to front wall panel using screws and washers.
right right
right and
right right
STEP
11
1
11
left door jambsleft door jambs
left door jambs
left door jambsleft door jambs
46
STEP
22
2
22
Page 47
SprSpr
Spr
Step 35Step 35
Step 35
Step 35Step 35
BW47
11
1After door has been completely in-
11
stalled, raise door to a full open posi­tion. Remove nut from bolt holding the horizontal track to the spring sup­port bracket, but do not remove bolt.
SprSpr
ing Restring Restr
ing Restr
ing Restring Restr
aint Caaint Ca
aint Ca
aint Caaint Ca
bb
b
bb
le le
All SizAll Siz
le
All Siz
le le
All SizAll Siz
eses
es
eses
22
2Slip keyed end of
22
cable cable
cable over shaft of bolt. Replace nut
cable cable
and tighten securely.
33
3Thread spring restraint cable
33
through spring, making sure cable goes through spring loops on each end of spring. Fasten to hole shown on angle of the horizontal track using a #10-32x3/8" bolt and square nut through keyed end of cable.
44
4Repeat above installation proce-
44
dure for the other spring.
This spring restraint cable has been
manufactured in accordance with require-
ments of the California Department of
Housing and Community Development.
spring restraintspring restraint
spring restraint
spring restraintspring restraint
NOTENOTE
NOTE
NOTENOTE
STEP
33
3
33
STEP
11
1
11
STEP
22
2
22
47
Page 48
VT1210VT1210
VT1210
VT1210VT1210
VT1217VT1217
VT1217
VT1217VT1217
VT1224VT1224
VT1224
VT1224VT1224
VT1231VT1231
VT1231
VT1231VT1231
697.68887697.68887
697.68887
697.68887697.68887
BW48
SOME FACTS ABOUT RUSTSOME FACTS ABOUT RUST
SOME FACTS ABOUT RUST
SOME FACTS ABOUT RUSTSOME FACTS ABOUT RUST
Rusting is a natural oxidizing process that occurs when bare metal is exposed to moisture. Problem areas include screw holes, unfinished edges, or where scrapes and nicks occur in the protective coating through normal assembly, handling and use. Identifying these natural rusting problem areas and taking some simple rust protection precautions can help to stop rust from developing, or stop it quickly as soon as it appears.
697.68888697.68888
697.68888
697.68888697.68888
1. Avoid nicking or scraping the coating surface, inside and out.
2. Use all the washers supplied. In addition to pro­tecting against weather infiltration, the washers pro­tect the metal from being scraped by the screws.
3. Keep roof, base perimeter and door tracks free of debris and leaves which may accumulate and retain moisture. These can do double damage since they give off acid as they decay.
4. Touch up scrapes or nicks and any area of visible rust as soon as possible. Make sure the surface is free of moisture, oils, dirt or grime and then apply an even film of high quality touch-up paint.
704880801
Loading...
Buy Points How it Works FAQ Contact Us Questions and Suggestions Privacy Policy Cookie Policy Terms of Use