Page 1
AS-2743
ARNOTT REmANufAcTuREd
fRONT RighT AiR STRuT
fOR
2005-2011 Audi A6 (c6 chASSiS)
Congratulations on your purchase of an Arnott® air suspension product. We at Arnott Incorporated are proud
to offer a high quality product at the industry’s most competitive pricing. Thank you for your condence in us
and our product.
Proper installation is essential to experience and appreciate the benets of this system. Please take a moment
to review these installation instructions before you begin to install these components on your vehicle. The
removal and installation of air suspension products should only be performed by a fully qualied, ASE
Certied, professional.
It is equally important to be aware of all necessary safety measures while installing your new Air Suspension
System. This includes proper lifting and immobilizing of the vehicle and isolation of any stored energy to
prevent personal injury or property damage.
"Engineered to Ride, Built to Last™"
WARNING:
and disconnect power to the air suspension system prior to disassembly. Do not allow dirt or grease to enter the system.
Always wear standard hand, ear, and eye protection when servicing the air suspension system.
The air suspension system is under pressure (up to 10 bar, or 150 lbf/in). Verify pressure has been relieved
KIT CONTAINS:
PARTS LIST
P/N QTY DESCRIPTION
21-7667 1 ARNOTT REMANUFACTURED FRONT RIGHT AIR STRUT
21-7668 1 ACCESSORY KIT
Arnott® is committed to the quality of its products. If you have a question or problem with any Arnott product,
please contact Arnott by calling 800-251-8993 during normal business hours or email techassistance@arnottinc.com
1 AS-2743
REV 1 04/28/2014
Page 2
AS-2743
ARNOTT REmANufAcTuREd
fRONT RighT AiR STRuT
fOR
2005-2011 Audi A6 (c6 chASSiS)
GENERAL INFORMATION:
Reading this manual signies your agreement to the terms of the general release, waiver of liability, and hold harmless agreement,
the full text of which is available at www.arnottinc.com.
• Not to be stored below 5oF (-15oC) and above 122oF (50oC).
• Avoid damage to air lines and cables.
• Removal and installation is only to be performed by fully qualied personnel.
• Use car manufacturer’s diagnostic software.
CAUTION:
in the instructions or in a different sequence.
Damage to the vehicle and air suspension system can be incurred if work is carried out in a manner other than specied
To avoid the possibility of short circuits while working with electric components consult your owner's manual on how to
disconnect your battery.
Consult your vehicle owner's manual, service manual, or car dealer for the correct jacking points on your vehicle and for
additional care, safety and maintenance instructions. Under no circumstances should any work be completed underneath
the vehicle if it is not adequately supported, as serious injuries and death can occur.
AIR STRUT REMOVAL
1. SET STEERING TO STRAIGHT AHEAD.
2. LIFT VEHICLE AND REMOVE WHEEL. (FIGURE 1)
2 AS-2743
FIGURE 1
REV 1 04/28/2014
Page 3
AS-2743
ARNOTT REmANufAcTuREd
fRONT RighT AiR STRuT
fOR
2005-2011 Audi A6 (c6 chASSiS)
3. LOCATE AND REMOVE THE SEAL AND PLASTIC COVER IN THE ENGINE COMPARTMENT. (FIGURE 2)
FIGURE 2
4. LOCATE AND REMOVE THE TREE (3) TOP MOUNTING BOLTS. (FIGURE 3)
3 AS-2743
FIGURE 3
REV 1 04/28/2014
Page 4
AS-2743
ARNOTT REmANufAcTuREd
fRONT RighT AiR STRuT
fOR
2005-2011 Audi A6 (c6 chASSiS)
5. LOCATE AND REMOVE THE AIR LINE. REMOVE THE AIR LINE FITTING FROM THE AIR HOSE AND
DISCARD. (FIGURE 4)
FIGURE 4
6. LOCATE AND DISCONNECT THE ELECTRICAL PLUG FROM THE BOTTOM OF THE SHOCK. (FIGURE 5)
FIGURE 5
7. LOOSEN AND REMOVE THE PINCH BOLT HOLDING THE UPPER CONTROL ARMS TO THE SPINDLE
ASSEMBLY. (FIGURE 6)
4 AS-2743
FIGURE 6
REV 1 04/28/2014
Page 5
AS-2743
ARNOTT REmANufAcTuREd
fRONT RighT AiR STRuT
fOR
2005-2011 Audi A6 (c6 chASSiS)
8. LOOSEN AND REMOVE THE LOWER MOUNTING NUT AND BOLT. (FIGURE 7)
FIGURE 7
9. REMOVE THE AIR STRUT FROM THE VEHICLE. (FIGURE 8)
5 AS-2743
FIGURE 8
REV 1 04/28/2014
Page 6
AS-2743
ARNOTT REmANufAcTuREd
fRONT RighT AiR STRuT
fOR
2005-2011 Audi A6 (c6 chASSiS)
10. REMOVE THE FOUR (4) TOP MOUNTING NUTS TO SEPARATE THE AIR STRUT FROM THE TOP MOUNT
ASSEMBLY. (FIGURE 9)
FIGURE 9
10. REMOVAL COMPLETE.
AIR STRUT INSTALLATION
Tighten all nuts and bolts to manufacturer's specications during the installation process.
Do not remove the air tting from the air spring. Doing so may cause damage and/or void warranty. Remove the white
shipping pin from the new air tting and insert the air line until fully seated.
1. INSTALLATION IS IN THE REVERSE ORDER OF AIR STRUT REMOVAL.
6 AS-2743
REV 1 04/28/2014
Loading...