Armytek Wizard XP-L Magnet USB Service Manual

Warnings

Model

Wizard XP-L Magnet USB

LED / Optics

Cree XP-L / TIR

Brightness stabilization type

DIGITAL (CPU brightness control)

Light output, LED / OTF lumens*

1250 / 1000

Peak beam intensity, candelas

3560

Hotspot / spill

70° / 1 20°

Beam distance*

119 meters

Modes, light output (OTF
lumens*) and runtimes
(measured with 18650 Li-Ion
3400mAh until the light output
drops to 10% of the initial
value)

Turbo

1000 lm / 1.5h

Main3

390 lm / 3.8h

Main2

180 lm / 9h

Main1

30 lm / 48h

Firefly2

2.3 lm / 18d

Firefly1

0.4 lm / 100d

Power source

1x18650 Li-Ion

Size and weight (without batteries)

Length 108mm, body diameter 24.5mm, head diameter 29mm, weight 65g

The flashlight will get hot in Turbo mode quickly and discharge the battery by high current. Don't leave it without your attention as very

bright light can heat objects and be a cause of the fire.

1. Always follow the instructions from this manual and recommendations on battery usage.

2. Apply only the recommended power sources.

3. Do not reverse battery polarity.

4. Do not use different power sources together, i.e. old ones with new ones, charged with

discharged. Do not use different types of batteries combined as the element with less
capacity can be damaged.

5. Do not modify or recast the flashlight and its components as it will deprive you of the

warranty.

6. Do not allow water or any other liquid to leak into the flashlight.

7. Do not aim a switched-on flashlight at people's or animals' eyes – it can cause temporary

blindness.

8. Do not allow children to use the flashlight without your assistance.

Wizard

Magnet USB

THE MOST TECHNICALLY ADVANCED

USER MANUAL

Thank you for choosing the products of Armytek Optoelectronics Inc., Canada.

Please read this manual carefully before using the flashlight.

Specifications

The producer will not be liable for any harm done to the user if it was caused by
improper use of the product.

Care and Storage

It is recommended to clean the threads and O-rings off dirt and old grease once or twice per year. Remember that reliable protection
from water and dust cannot be provided by worn out sealing. The fouling as well as lack of lubricant cause fast wear-out of threads and
sealing rings.

To clean the threads do the following:

1. Unscrew the tailcap and remove the sealing ring carefully with a toothpick (do not use sharp metal things as they can damage the ring).

2. Wipe the sealing ring thoroughly with a soft cloth (or tissue). Do not use solvents. If the sealing ring is worn out or damaged

replace it by a new one.

3. Clean the metal threads with a brush using ethanol. Be careful not to allow the applied liquid to get inside the flashlight or tailcap as

it can cause fails in functionality of the flashlight.

After cleaning lubricate the thread and the sealing ring with polyalphaolefin-based silica grease, e.g. Nyogel 760G.The application of
automotive and other improper grease can cause swelling and damage of the sealing rings.

In case of active operation and exploitation in dusty environments, it is recommended to perform cleaning and lubricating of the parts
as often as required.

Service and Warranty

Armytek provides free warranty repair for 10 years (excluding batteries, chargers, switches and connectors which have 2 years
warranty) from the date of buy with the document confirming the purchase.

Guarantee does not extend to damage during:

1. Improper usage.

2. Attempts to modify or repair the flashlight by nonqualified specialists.

3. Longtime application in chlorinated or polluted water, or other liquids (other than water).

4. High temperatures and chemicals' exposure (including the exposure of liquid from defected batteries).

5. Usage of low-quality batteries.

Armytek Optoelectronics Inc. is a Canadian manufacturer that produces powerful and reliable flashlights designed especially for your
needs. The components made in the USA and Japan. .10 years no-hassle warranty

§ Amazingly powerful multi-flashlight with 1250 LED lm brightness powered by only one 18650 Li-Ion battery.

§ Rechargeable flashlight with magnet USB charger.

§ TIR optics with light angles 70°:120° for wide light without a “tunnel vision” effect.

§ Easy operation and 6 convenient brightness modes.

§ Due to a side switch button you can operate the multi-flashlight easily with one hand without shifting it aside.

§ Compact and light-weight but at the same time durable and multi-functional flashlight.

§ Record runtimes – up to 100 days of operation on one battery.

§ Magnet in the tailcap, removable clip for fixation on a belt and flat tailcap for vertical standing.

§ Complete correspondence to the highest standards of durability and reliability: the multi-flashlight easily withstands fallings,

impacts and vibrations.

* Light output for flashlights with Warm light are about 7% less, beam distances are about 3% less.

Web: www.armytek.com Email: [e-mail]

Address: 13-85 West Wilmot St, Richmond Hill, Ontario, L4B 1K7, Canada

Specifications are subject to change without notice.

Armytek Optoelectronics Inc.

Remember that old or low-quality batteries can be damaged under heavy load and explode.

Set description

Operation

2

1

Wizard

Magnet USB

ь Your flashlight can inconsiderably differ from the pictures in the manual.
ь The producer reserves the right to change the package at his own discretion without modifying this manual.

x2

6

4

5

7

8

Items included in the package:

1 - Flashlight 6 - 2 spare O-rings
2 - Clip 7 - Magnet USB charger
3 - User manual 8 - Plastic holder

3

4 - 18650 Li-Ion battery
5 - Headband (2 straps)

Initial Service

1.

3.

2.

To set/replace batteries:

1. Unscrew the tailcap.

2. Place the batteries with the positive contact (+) facing the head of the flashlight.

3. Adjust the tailcap and tighten it as far as it can go.

The flashlight is ready for operation.

We DO NOT RECOMMEND to leave power sources inside the flashlight for a long storage period, as batteries (especially, non-rechargeable) can
leak for various reasons and damage the inner parts of the flashlight. If you want to keep your flashlight in a stand-by state with batteries in then use
new and high-quality batteries and store the flashlight in acceptable for batteries operational temperature and revise the batteries' state at least
once a month. If you have noticed any signs of batteries' defects then withdraw them from the flashlight and utilize. It is also recommended to
replace discharged batteries with new ones before the storage as the chance of leakage is higher with discharged batteries.

To use the headmount with the flashlight: How to turn on a magnet charger:

Pass the end of the

1.

band B through the
clasp.

a

B

2.

Pass the band A
through the eye of the
band B.

A

3.

Put in the band A in the first clasp.

A

Pass the end of the band A through the

4.

second clasp and fix it.

Unscrew the tailcap for 1/4 of a circle and turn
on a magnet charger device to the tailcap.

1/4

A

Put in the bands

5.

B

through the slots in
the plastic holder
and fix the
flashlight. Adjust
elastic bands to the
size of your head.

Charger device battery indication:

1. Red color – the charging is going on.

2. Green color – the charging is finished.

3. Red color blinking – unscrew the tailcap
for 1/4 for charging.

In OFF state:

Click: To turn on the last used mode.
Press and hold: To go through 2 Firefly modes (release to select). Keeping button pressed will start cycling through the Main modes.

In ON state:

Click: To turn off the flashlight.
Press and hold: To start cycling through the Main modes.
Double click: To turn on the Turbo mode. The second double click brings back the last used mode.

For comfortable operation you have a convenient momentary access to all the following modes:

Press & Hold

OFF вFirefly1 вFirefly2

Click x1

OFF вMain (if last used)

Click x2

ON вTurbo
Turbo вLast mode

Press & Hold

Automemorizing. After switching off the last used Mode is memorized for quick 1-click access at next switching on.

Lock-out function. Unscrew the tailcap to 1/4 for the protection from accidental switching on.

Low Battery Indication

Warning

Critical

вFirefly1
вOFF

Cycling through Modes

Main1 вMain2

ез

Main3

Low Battery Indication. If the brightness is <25% from the nominal value, the LED flashes 2 times

ONCE (after 30sec from switching on). If you are not sure if it flashed or not switch the flashlight
off and on: in case the battery is low flashes will repeat. Light output decreases to Firefly mode at
critical level.

Active temperature control. The flashlight can quickly heat up in Turbo mode. When the
temperature become +60°C – the brightness decreases by small steps. After cooling-down
(provided that battery voltage is sufficient) the brightness increases to the Turbo mode again.

This stepping goes cyclically to maintain the user's safety and the flashlight's functionality. In
conditions of good air-cooling the flashlight delivers light without stepping down even in Turbo
mode. There are no preset timers for stepping, but real-time active temperature measurements.

Firefly

Main

Turbo

Firefly. Press and hold the button in OFF-state to turn on the

desired Firefly mode and then release immediately. Keeping
the button pressed will start cycling through the Main
modes.

Main. Short click from OFF-state activates the Main mode (if
it was the last mode used previously).

Turbo. The mode is activated by double click in any mode. To
return to the last mode make double-click again.

Cycling through the Main modes. In ON-state press and hold
the button (in any mode): the 3 Main modes will start
switching cyclically. Release the button to select the desired
mode. In Turbo mode it starts cycling through the Main

modes.