ARM Electronics C600BCDNVFIR User Manual
C600BCDNVFIR
(AC 24V)
(DC 12V)
(BNC)
600 Line WDR Bullet Camera with 80’ IR Range
DAY/NIGHT, 2DNR, D-WDR, OSD, CABLE MGMT, 2-8.12mm LENS
PRODUCT FEATURES
•
600 Lines of Resolution
•2.8-12mm Auto Iris Lens
•Wide Dynamic Range (WDR) Technology
•2DNR Digital Noise Reduction
•Built in OSD & Video Test Connection
•80’ IR Range
•Dual Voltage Power
•IP 66 Weatherproof
SPECIFICATIONS
Model No. C600BCDNVFIR
Image Pick-Up Device 1/3” Sony Super HAD II CCD
TV System NTSC
Total Pixels 811(H) * 508(V )
Eective Pixels 768(H) * 494(V)
Scanning System 2:1 Interlace
Synchronization Internal / Line Lock (in 24 VAC)
O.S.D Yes, Built-in
Backlight OFF / HSBLC / BLC Selectable
Resolution 600TV Lines
S/N (Y signal) 52dB (AGC O, Weight On)
Minimum Illumination 0.01Lux / IR LED ON: 0.0Lux
White Balance ATW / AWB / Manual / AWC >SET
Electronic Shutter Speed AUTO (1/60sec ~ 1/100,000sec)
Gain Control High, Middle, Low, O (Selectable)
2 DNR 2D-DNR (1~50 Level Adjustable)
D-WDR Indoor / Outdoor / O
Motion Detection On / O (4 Zone, Alarm Output)
Privacy On / O (8 Zone)
Mirror O / Mirror / V-Rev / Rotate
Freeze On / O
Sharpness 0~31 (Level Adjustable)
D&N Selection Color / BW / Auto / EXT
Digital Zoom On (2-32X) / O
Blemish Compensation Auto: 128 Point / Manual: 4 Point
Power Dual Power (24 VAC / 12 VDC)
Power Consumption IR LED ON: 250mA Max
Lens Auto Iris 2.8mm-12mm
Operational Temp. -14° F ~ 122° F RH 95% Max.
Dimension 2.6 x 3.5 x 7.4
Weight 1.8LB
Weatherproof Rating IP66
IR LED Count 14pc
IR LED Range 80’
* All specications subject to change without notice for quality improvement
CAMERA DIMENSIONS
2.6”
4.7”
ARM Electronics
2.1”
CABLE CONNECTION
(BNC)
(AC 24V)
(DC 12V)
OSD Control
Board
CAMERA LAYOUT
7.4”
OSD
Adapter
Plate
PACKAGE CONTENTS
(1) Camera
(1) User’s Manual
(1) Base Adapter Plate
(1) L-Wrench 3.0mm
(4) Bolt M4 x 7, Hexagon Socket
(4) Screw 4 x 20
(1) Video Test Cable
ARM Electronics Roseville, CA 95678 1. 855.388.7422 w ww.armelectronics.com Rev. 0711 11
SEE REVERSE SIDE FOR PRODUCT
SAFETY & HANDLING INFORMATION
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION:TO REDUCE THE RISK OF ELECTRIC SHOCK
DO NOT REMOVE COVER(OR BACK).
NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
ISO14001
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION:TO REDUCE THE RISK OF ELECTRIC SHOCK
DO NOT REMOVE COVER(OR BACK).
NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
ISO14001
C600BCDNVFIR
600 Line WDR Bullet Camera with 80’ IR Range
DAY/NIGHT, 2DNR, D-WDR, OSD, CABLE MGMT, 2-8.12mm LENS
SAFETY INSTRUCTIONS
•
This camera should be installed by qualied
personnel only.
•Do not disassemble this camera, There are no user-
serviceable parts inside.
•Use a UL approved regulated 24 volt AC or 12 volt DC
power supply.
•Use appropriate low voltage power cable to prevent
re or electrical shock.
•Please insure that your installation area can support
the weight of the camera.
HANDLING INSTRUCTIONS
•
Do not use a strong or abrasive detergent
when cleaning the camera.
•Do not point the camera directly into sunlight.
•Do not install camera in places where humidity is high.
•Do not install near a cooling or heating device.
•
Do not expose internal components to rain or moisture.
PRECAUTIONS FOR USE
Do not install the camera in
extreme temperature conditions.
Only use the camera under conditions
where temperatures are between -14° F
~ 122° F. Be especially careful to provide
ventilation when operating under high
temperatures.
Do not install the camera under
unstable lighting conditions.
Severe lighting change or icker can
cause the camera to work improperly.
Do not install or use the camera in an
environment where the humidity is high.
Do not install or use the camera in an
environment where the humidity is high.
Do not touch the front lens of the
camera.
This is one of the most important parts
of the camera. Be careful not to leave
ngerprints on the lens cover.
INFORMATION - This equipment has been tested and found to comply with
limits for a Class A digital device, pursuant to part 15 of the FCC Rules & CE Rules.
These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instruction manual, may cause
harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at
their own expense.
This installation should be made by a qualied service person
and should conform to all local codes.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION:TO REDUCE THE RISK OF ELECTRIC SHOCK
DO NOT REMOVE COVER(OR BACK).
NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
ISO14001
The lightning ash with an arrowhead symbol, within an equilateral
triangle is intended to alert the user to the presence of uninsulated
dangerous voltage within the product's enclosure that may be of
sucient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert
the user to the presence of important operating and maintenance
(servicing) instructions in the literature accompanying the appliance.
WARNING - Changes or modications not expressly approved by the
manufacturer could void the user’s authority to operate the equipment.
CAUTION : To prevent electric shock and risk of re hazards:
Do NOT use power sources other than those specied.
Never keep the camera pointed
directly at strong light.
It can cause malfunctions to occur.
Do not expose internal components
to rain or moisture.
If it gets wet, wipe dry immediately.
Liquids can contain minerals that
corrode the electronic components.
Do not drop the camera or subject
it to physical shocks.
Housing damage can compromise
weatherproof ratings.
Do not expose the camera to
radioactivity.
If exposed to radioactivity the CCD
will fail.
NOTE
If the camera is exposed to spotlight or object reecting strong light,
•
smear or blooming may occur.
please check that the power satises the normal specication before
•
connecting the camera.
ARM Electronics Roseville, CA 95678 1. 855.388.7422 w ww.armelectronics.com Rev. 0711 11
Loading...