Armatix SMARTIW1A, SMARTIP1A, SMARTIS1A User Manual
iP1 SmartSystem – Personalized
Instruction Manual
• Read this manual carefully before loading or using the iP1 pistol.
WARNING
• The iP1 pistol will not operate if it is not within 10” of the iW1 wristwatch with the
matching key and the PIN code entered.
EN
This manual is only intended:
• For use with an iP1 pistol that has been referenced to an iW1
wristwatch; or
• to guide through the process of upgrading the iP1 Smart-
System – Basic to the iP1 SmartSystem – Personalized (see
Chapter 27)
Armatix U.S.A., Inc.
Pistol iP1
Caliber .22lr
iP1 SmartSystem – PersonalizediP1 SmartSystem
2
iP1 SmartSystem – Personalized
3
iP1 SmartSystem – PersonalizediP1 SmartSystem
Safety precautions
Read this manual and the warnings contained in it before loading or using the iP1 pistol. This manual explains the
function and the handling of the iP1 SmartSystem — Personalized and warns of the potential dangers, including
death and serious personal injury, that can result from use of the iP1 pistol. This manual should always accompany
the iP1 SmartSystem — Personalized and be transferred with it if it is sold or otherwise made availebal to another
person.
Even if you are an experienced shooter, you must READ THIS ENTIRE MANUAL CAREFULLY before loading or firing
the iP1 pistol because it represents the first commercially available “personalized” firearm and has several unique
features and operating requirements not present in other firearms. This manual gives basic instructions on the
proper handling and functioning of the iP1 pistol. Your safety and the safety of others depend on you following the
instructions and warnings in this manual and the constant use of safe firearms practices. If you are unfamiliar with
firearms, take a course in the safe handling of firearms run by a qualified firearms instructor, your local gun club,
or a similar qualified organization.
Safety warning symbols
This manual contains several safety warnings and instructions preceded with:
These signal words are designed to draw your attention to important
safety information.
Indicates a hazardous situation which, if not avoided, could result in death or serious injury.
Indicates a hazardous situation, which, if not avoided, could result in minor or moderate injury.
Addresses safety practices not related to personal injury.
4
iP1 SmartSystem – PersonalizediP1 SmartSystem
General safety precautions
• Failure to follow the safety information and safety instructions in this manual could result
in death, serious personal injury and/or property damage.
• The iP1 pistol is intended for target shooting only and will not function if it is not within
10” of the referenced iW1 wristwatch and the PIN code entered, or it or the referenced
iW1 wristwatch do not have sufficient battery power, or communication between them is
blocked. It should not be relied upon for purposes of self-defense.
• Always deactivate the iP1 pistol when you are finished using it to help prevent it from being
misused by third parties.
• Always seek a doctor’s advice if you are taking medication to be sure that you are able to
shoot and handle a firearm safely.
• Never drink alcoholic beverages or take drugs before or while shooting. Your vision and
judgment could be seriously impaired, making your firearm handling unsafe.
• If the iP1 pistol or any other firearm is carelessly or improperly handled, you could cause a
negligent discharge, which could result in death, serious personal injury and/or proper ty
damage.
• Always handle the iP1 pistol as if it is loaded so that you never fire negligently.
• Never point the iP1 pistol at anything you do not intend to shoot.
• Never pull the trigger or put your finger on the trigger or in the trigger guard until you have
made the decision to fire.
• Never take anyone’s word that a firearm is unloaded; always check for yourself, with the
firearm pointed in a safe direction and your finger off of the trigger and outside of the
trigger guard.
5
iP1 SmartSystem – PersonalizediP1 SmartSystem
• Always make sure the iP1 pistol is unloaded and that the slide is locked open in the rearward position with the magazine taken out before handing it to another person.
• Never alter or modify the iP1 pistol because this could cause it to malfunction and create
a dangerous condition.
• If the iP1 pistol is dropped or forcefully struck, it could be damaged and may not function
properly. Have it inspected by Armatix U.S.A., Inc. before continuing to use it.
• Do not expose the iP1 pistol to high heat or moisture because they could damage its electronic elements and prevent it from functioning properly.
• Never carry the iP1 pistol out of a suitable holster with a cartridge loaded in the chamber.
• Always store and transport the iP1 pistol unloaded and locked in a suitable container, such
as the included pistol case, out of the reach and sight of children or other unauthorized
persons. The personalized nature of the iP1 pistol is not an excuse for the failure to follow
safe firearm storage practices.
• Never store or transport ammunition or the synced iW1 wristwatch together with the PINCard and the valid PIN codes of the iP1 SmartSystem in the same container as the iP1
pistol. The PIN-Card and the valid PIN codes of the iP1 SmartSystem must always be stored
separately and out of the reach and sight of children or other unauthorized persons.
6
iP1 SmartSystem – PersonalizediP1 SmartSystem
Most ammunition contains lead in the projectile and/or primer. Firing the iP1 pistol in a poorly
ventilated area can lead to the exposure to lead. Always wash your hands after handling ammunition, firing the iP1 pistol, and/or performing preventive maintenance on the iP1 pistol to
minimize your exposure to lead.
Do not dry fire the iP1 pistol (pull the trigger and allow the hammer to fall on an empty chamber) because this will result in premature wear. To practice pulling the trigger, use snap caps
or dummy rounds.
7
iP1 SmartSystem – PersonalizediP1 SmartSystem
Before it left the factory, the iP1 pistol was tested, carefully inspected, and packaged. Armatix
U.S.A., Inc. cannot control what happens to the pistol after it leaves the factory, therefore, carefully examine the iP1 pistol when you acquire it to ensure that it is unloaded and undamaged. If
you do not understand any of the warnings and instructions in this manual or have any problems
operating the iP1 pistol, contact Armatix U.S.A., Inc.’s customer service/warranty department at
1-855-477-1972 or customerservice@armatix.us. If you need another copy of this manual, contact
Armatix U.S.A., Inc.
Manufactured by: Imported and distributed in the United States by:
Armatix GmbH Armatix U.S.A., Inc.
Feringastraße 4 23121 Coltrane Avenue
85774 Unterföhring Germany Newhall, CA 91321
Tel.: +49 89 / 4 27 29 79 – 0 Tel.: 855-477-1972
Email: info@armatix.de Email: customerservice@armatix.us
Webpage: www.armatix.de Webpage: www.armatix.us
The Upto Date version of the instruction manual can also be downloaded at www.armatix.us.
8
iP1 SmartSystem – Personalized
Table of Contents
1 Introduction 12
2 Main Features of the iP1 Pistol 13
2.1 The iP1 14
2.1.1 Frame with LED and interchangeable backstraps 14
2.1.2 Slide with loaded chamber indicator (LCI) 14
2.1.3 Trigger with trigger switch 15
2.1.4 Slide release lever 16
2.1.5 Magazine release lever 16
2.1.6 Sights 16
3 Functioning of the iP1 SmartSystem – Personalized 17
4 Components of the iP1 SmartSystem – Personalized 18
5 Operation of the iW1 wristwatch 19
5.1 Display elements 19
5.1.1 Scrolling through the individual function menus of the iW1 wristwatch 21
5.1.2 Background lighting 23
5.2 Standard display 23
5.2.1 Setting the time and date 24
5.2.2 Alarm clock 26
5.2.3 Stopwatch 27
5.2.4 Pistol menu 28
9
iP1 SmartSystem – Personalized
6 Activating the iP1 pistol 29
7 Deactivating the iP1 pistol 31
8 Synchronizing the time between the iP1 pistol & the iW1 wristwatch 32
9 Changing / resetting the 5 digit PIN code using the 12 digit SuperPIN 34
10 Resetting the iP1 pistol using the 10 digit pistol PIN code 36
11 Referencing the iP1 pistol to the iW1 wristwatch 38
12 Checking the batteries without using the iW1 wristwatch 40
13 Automatic battery charge indicator 41
14 Loading 42
15 Firing 44
16 Reloading when firing 47
17 Clearing malfunctions (jams) 48
18 Trouble shooting 50
18.1 Mechanical malfunctions 50
18.2 Electronic malfunctions 52
19 Unloading procedure and safety check 54
20 Disassembly 56
21 Cleaning 59
21.1 Barrel 60
21.2 Slide 61
21.3 Frame 62
21.4 Magazine 62
10
iP1 SmartSystem – Personalized
22 Changing the backstrap / replacing the batteries in the iP1 pistol 64
23 Adjusting and changing the sights 66
24 Assembly 67
25 Function test 69
26 Storing the iP1 pistol 70
27 Upgrading the iP1 SmartSystem - Basic to the iP1 SmartSystem - Personalized 71
28 Updating the firmware 72
29 Changing the iW1 wristwatch batteries 73
Part list 74
Exploded drawing 75
Technical data 76
Limited one year operational warranty 77
FCC notice 79
Youth Handgun Safety Act Notice 80
State required safety warnings 84
11
iP1 SmartSystem – PersonalizediP1 SmartSystem
1 Introduction
Dear Customer,
Thank you for choosing the Armatix iP1 SmartSystem – Personalized, which consists of the iP1 .22LR
pistol and the iW1 wristwatch and represents a revolutionary innovation.
The iP1 pistol is referenced to the iW1 wristwatch and can only be fired by the authorized user,
who has the referenced iW1 wristwatch and the required PIN code. This is designed to prevent the
iP1 pistol from being fired by unauthorized persons who may gain access to it, but do not have
the matching iW1 wristwatch and all required PIN code. If you purchased the iP1 pistol and iW1
wristwatch together as an iP1 SmartSystem – Personalized, they are already referenced on delivery
and therefore have the joint “key.”
The heart of the system, the iP1, is a modern, high precision, single-action/double-action, semiautomatic pistol developed according to state-of-the-art technology and engineering principles. The
iP1 pistol, which is designed for accurate target shooting at distances up to 27 yards, features a
mechatronic safety device. This safety device is active by default and can only be deactivated using
the iW1 wristwatch.
The iP1 SmartSystem – Personalized is more than just a revolutionary safety concept. It is a true
innovation and represents the pistol of the future here and now.
Your Armatix Team
12
iP1 SmartSystem – PersonalizediP1 SmartSystem
1
2 Main features of the iP1 Pistol
The iP1 pistol is a semi-automatic, single-action/double-action .22LR pistol with a ten round detachable magazine that
has been developed in accordance with the latest ergonomic principles and criteria. The parts and operating elements
of the iP1 pistol are identified in the figure below:
1 Front sight
2
2 Loaded chamber indicator
3
3 Rear sight
4
4 Hammer
5
5 Slide
6
6 LED
7
8
7 Slide release lever
9
8 Backstrap with backstrap switch
10
9 Trigger switch
11
12
10 Trigger
11 Magazine release lever
12 Cover
13
13 Magazine
14
14 Recoil spring
13
iP1 SmartSystem – PersonalizediP1 SmartSystem
1.1 The iP1
1.1 .1 Frame with LED and interchangeable backstraps
The frame features interchangeable backstraps in three different sizes to properly fit the hands of
different users. The iP1 pistol comes with the small backstrap installed. Medium and large backstraps are available as options and can easily be changed by the user. The backstrap is linked to the
backstrap switch, which is activated to communicate with the iW1 wristwatch when the backstrap
is squeezed towards the front of the iP1 pistol. Depending on the status of the iP1 pistol, the LED will
light up in different colors when the backstrap is squeezed towards the front of the pistol:
• Green signals that the iP1 pistol is ready to be fired.
• Blue signals that the magazine has not been inserted or has not been inserted correctly.
• Red signals that the iP1 pistol is not activated and cannot be fired.
1.1.2 Slide with loaded chamber indicator (LCI)
The slide has a loaded chamber indicator (LCI) to comply with the laws of certain states. The upper
opening of the slide serves as a loaded chamber indicator (LCI) by allowing the user to look inside
the chamber to see whether or not a cartridge is loaded.
Although the iP1 pistol has a loaded chamber indicator (LCI) you should never solely rely on
it or your memory to determine whether the iP1 pistol is loaded or unloaded. Always retract
the slide by grasping it at the indented area at the rear of the slide and pulling it fully to the
rear and then visually and physically (with your finger) check to make sure there is not a
cartridge in the chamber.
14
iP1 SmartSystem – PersonalizediP1 SmartSystem
1.1.3 Trigger with Trigger Switch
The trigger includes a mechanical locking switch with prevents it from being pulled to the rear.
When the trigger switch is in the left position (when viewed in the firing direction, with the muzzle
pointed away from the user), the trigger is locked. When it is in the right position, the trigger is
released and can be pulled.
Pistol safe.
Trigger switch pressed
to the left in firing
direction.
Although iP1 pistols have several internal safeties features designed to prevent an unintentional discharge if the pistol is dropped or hit, the proper and safe function of the iP1 pistol
depends on it being used for its intended purposes and not being altered or modified. Like
any other mechanical device, if the iP1 pistol is subject to unusual and extreme forces, failure
can occur. Therefore, safe firearm handling practices and the instructions and safety warnings in this manual must always be followed to minimize the risk of a negligent discharge.
In case any of the iP1 pistol’s safety features prove to be ineffective for any reason, the
possibility of an unintentional discharge exists. If so, the iP1 pistol should be immediately
unloaded and not be used again until it has been examined by Armatix U.S.A., Inc.
15
Pistol safe.
Trigger switch pressed
to the left in firing
direction.
Pistol armed. Trigger
switch pressed to
the right in firing
direction.
Pistol armed. Trigger
switch pressed to
the right in firing
direction.
iP1 SmartSystem – PersonalizediP1 SmartSystem
1.1.4 Slide Release Lever
When the last round in the magazine is fired, the slide release lever will hold the slide locked in the
rearward position to signal that the magazine is empty. When the slide is pulled back with an empty
magazine in place, it will also be held in the rearward position by the slide release lever. In addition,
when there is no magazine inserted, the slide release lever can be manually pushed up to lock the
slide in the fully rearward position.
1.1.5 Magazine Release Lever
The magazine release lever is located beneath the trigger guard and is designed for use by both
right handed and left handed shooters. To remove the magazine, simply press down on the magazine lever from either the right or left side.
1.1.6 Sights
The front sight is available in four different heights and can easily be changed by the user. The rear
sight features a trapezoidal recess to simplify centering the front sight.
16
iP1 SmartSystem – PersonalizediP1 SmartSystem
2 Functioning of the iP1 SmartSystem – Personalized
The following describes how the iP1 pistol functions when the magazine is inserted, a round is in the
chamber, the trigger switch is in the right (released) position, and the synced iW1 wristwatch with
the PIN code entered and the pistol feature activated is worn on the wrist of your shooting hand:
• When the backstrap is squeezed towards the front of the iP1 pistol, the backstrap switch is
activated and communication between the iP1 pistol and iW1 wristwatch is initiated;
• When the trigger is pulled slightly to the rear, the iP1 pistol is activated for firing and the LED
lights up green.
• When the trigger is pulled fully back within 60 seconds, depending on the position of the ham-
mer, the following happens:
• If the hammer is already cocked (in the rear position), it is immediately released (fired in
single-action mode) or if the hammer is not cocked (in the forward position) it will first be fully
cocked and then immediately released (fired in double-action mode);
• When the hammer is released, it strikes the firing pin, which fires the cartridge in the cham-
ber;
• The recoil energy from the cartridge being fired causes the slide to move rearward, extracts
the fired cartridge casing from the chamber, ejects it, and cocks the hammer;
• The recoil spring then brings the slide forward to the closed position, during which it strips the
next cartridge from the magazine and transports it to the chamber.
• When the trigger is released, the iP1 pistol is ready to be fired again, until the last cartridge
in the magazine has been fired, after which the slide release will lock the slide in the open
(rearward) position.
Once you pull the trigger slightly to the rear, the iP1 pistol is activated for firing. You must pull
the trigger fully to the rear within 60 seconds or the iP1 pistol will return to inactive mode to
conserve battery power. If you do not pull the trigger fully to the rear within 60 seconds, you
must completely release the trigger to reactivate the pistol to allow it to be fired.
17
iP1 SmartSystem – PersonalizediP1 SmartSystem
3 Components of the iP1 SmartSystem – Personalized
Scope of supply
• iP1 pistol with magazine
• iW1 wristwatch (already referenced to the iP1 pistol)
• Lockable storage/transportation case
• Printed instruction manual
• PIN-card
• 1/10” diameter punch
• 2 AAA batteries for the iP1 pistol
• 1 CR2032 battery (already installed in the iW1 wristwatch)
• Warranty card
• Target: showing the grouping of the shots from the iP1 pistol
18
iP1 SmartSystem – PersonalizediP1 SmartSystem
4 Operation of the iW1 wristwatch
The iW1 wristwatch is used to control the iP1 pistol and should be worn on the wrist of your firing
hand as it must be within 10” of the iP1 pistol to communicate with it. Using a PIN code, it can be
used to activate the iP1 pistol, set the amount of time within which the iP1 pistol will remain active,
and deactivate the iP1 pistol before the set time expires. It indicates when the iP1 pistol is active, as
well as the charge level of the batteries of the iP1 pistol. In addition, it also functions as a normal
digital wristwatch, displaying the time and date, and features an alarm clock and stop watch.
4.1 Display elements
In addition to the time and date, the respective active functions of the iW1 wristwatch are indicated
by various symbols on the display.
12
11
10
1 Pistol menu
2 Setting of remaining time
1
3 Alar m clock / stopwatch
2
4 Warning
3
5 Delete
4
6 Stopwatch start / s top
5
7 Date
6
8 Alar m clock On / Off
7
9 iW1 wristwatch battery
8
10 Display of remaining time
9
11 Pistol function of the iW1 wrist-
watch / iP1 pistol battery
12 Time
19
iP1 SmartSystem – PersonalizediP1 SmartSystem
Symbol Meaning
Pistol menu
The small pistol symbol appears in the top right-hand corner when the pistol menu is called up.
Settings related directly to the pistol can be carried out here.
Remaining time
The symbol appears during setting of the remaining time. In the lower half of the display it indicates the remaining time displayed alongside for which the iW1 wristwatch
is activated.
Alarm clock
The symbol appears during setting of the alarm time.
After setting the alarm time, the alarm clock can be switched on (
When the alarm clock is switched on, the symbol
is switched on.
Stopwatch
The stopwatch symbol appears in the top right-hand corner of the display when the
stopwatch is active.
The start-stop symbol appears when the stopwatch is called up and indicates that the
stopwatch can be started, stopped and reset with the button MR.
Delete
The 'Delete' symbol indicates that the last input (e.g. the last digit entered during input
of the PIN code) can be deleted with the button MR.
Warning
This symbol indicates a failar.
iW1 Wristwatch battery
This symbol needs the battery of the iW1 wristwatch replaced.
Pistol function of the iW1 wristwatch / pistol battery
The large pistol symbol appears in every menu when the pistol function of the iW1
wristwatch is activated.
The three bars in the grip indicate the charge level of the battery in the pistol. They only
appear when communication has been established with the pistol.
indicates that the alarm clock
) or off ( ).
20
iP1 SmartSystem – PersonalizediP1 SmartSystem
4.1.1 Scrolling through the individual function menus of the iW1 wristwatch
The basic functions of the iW1 wristwatch can be scrolled through using the bottom right and top
right buttons. Pressing the bottom right button will change the menu from the standard display
(time & date) to the pistol menu, the alarm clock, the stopwatch and back to the standard display.
Each pressing the top right button will change the menu in the opposite order.
To bring up a submenu, press the top right button for three seconds.
Unless alarm clock or stopwatch functions are in use, if no buttons are pressed within 20
seconds, the iW1 wristwatch will return to the standard display.
1
2
3
4
5
6
1 Button top left (TL)
2 Button top right (TR)
3 Display
4 Button middle right (MR)
5 Button bottom right (BR)
6 Button bottom left (BL)
21
iP1 SmartSystem – PersonalizediP1 SmartSystem
The basic functions of the wrist watch can be scrolled through with the buttons BR and TR in the
recurring sequence illustrated below:
Menu sequence when scrolling through with button BR or TR.
BRBR
22
Stopwatch
TR
TR
Standard display
Time / date
Alarm clock
TR
Pistol menu
TR
BRBR
iP1 SmartSystem – PersonalizediP1 SmartSystem
4.1.2 Background lighting
The background lighting of the iW1 wristwatch display is activated by pressing the bottom left button for 3 seconds. The background lighting will shut off automatically after a short time.
4.2 Standard display
The standard display shows time and date. In addition, when the pistol function of the iW1 wristwatch is activated and it is in communication with the iP1 pistol, the pistol icon will be shown in
the bottom left corner of the display, along with the remaining time until the pistol automatically
becomes deactivated. The status of the iP1 pistol’s battery charge is shown by the three bars in the
grip of the pistol icon:
Status of the pistol battery
Battery capacity 100% Battery capacity approx. 66%
Battery capacity approx. 33% (Bar flashes) Battery empty
The standard display
Current time. Current date.
23
iP1 SmartSystem – PersonalizediP1 SmartSystem
When the pistol function of the iW1 wristwatch is activated, the following information is displayed:
Activation status of the
iW1 wristwatch and
status of the pistol battery (bars in the grip).
4.2.1 Setting the time and date
Beginning with the standard display, set the time and date by completing the following steps:
1. Press the top right button for three seconds to bring up the time setting submenu.
2. Adjust the hour by pressing the top left button to increase the hour or the bottom left button
to decrease the hour, and then press the top right button to confirm the hour setting and move
to the minute setting.
3. Adjust the minutes by pressing the top left button to increase the minutes or the bottom left
button to decrease the minutes, and then press the top right button to confirm the minute
setting and move to the date setting.
4. Adjust the date by pressing the top left button to increase the date or the bottom left button
to decrease the date, and then press the top right button to confirm the date setting and move
to the month setting.
5. Adjust the month by pressing the top left button to increase the month or the bottom left but-
ton to decrease the month, and then press the top right button to confirm the month setting
and move to the year setting.
6. Adjust the year by pressing the top left button to increase the year or the bottom left button
to decrease the year, and then press the top right button to confirm the year setting and move
to the time format setting.
Remaining time until
automatic deactivation
of the pistol function of
the iW1 wristwatch.
24
iP1 SmartSystem – PersonalizediP1 SmartSystem
7. Press the top left button or the bottom left button to alter between 24 hour and 12 hour
(a.m. / p.m.) format. Press the top right button to confirm the time format and return to the
standard display.
If the 24 hour time format is selected, the date will be displayed as date, month, year. If the 12
hour time format is selected, the date will be displayed as month, date, year.
3 sec.
Call up setting:
Hold TR pressed for 3
seconds.
+
–
Month:
Set (TL, BL)
and confirm (TR).
25
OK
+
–
Hours:
Set (TL, BL)
and confirm (TR).
+
–
Year:
Set (TL, BL)
and confirm (TR).
OK
OK
+
–
Minutes:
Set (TL, BL)
and confirm (TR).
24h
12h
12h / 24h mode:
Select (TL, BL)
and confirm (TR).
OK
OK
+
–
Day:
Set (TL, BL)
and confirm (TR).
Standard display
appears.
OK
iP1 SmartSystem – PersonalizediP1 SmartSystem
5.2.2 Alarm clock
The iW1 wristwatch has an alarm clock that will sound for 20 seconds at the set time. To set the
alarm, complete the following steps:
1. Beginning with the standard display, press the bottom right button twice to bring up the
alarm clock menu. The last time for which the alarm clock was set will be displayed.
2. Press the top right button for three seconds to set the alarm.
3. Adjust the hour by pressing the top left button to increase the hour or the bottom left button
to decrease the hour, and then press the top right button to confirm the hour setting and move
to the minute setting.
4. Adjust the minutes by pressing the top left button to increase the minutes or the bottom left
button to decrease the minutes, and then press the top right button to confirm the minute
setting.
5. When the alarm time is set, press the top left button to turn the alarm on, or the bottom left
button to turn the alarm off. Press the top right button to confirm your selection and to return
to the standard display.
When the alarm sounds, it can be turned off by pressing any button. It will sound again when the
set time is reached the next day. To deactivate the alarm, complete steps one and five above.
3 sec.
+
OK
+
OK
2x
Call up "Alarm clock"
menu:
Press BR 2x.
26
Display last alarm
time. To set:
Hold TR pressed for
3 seconds.
–
Hours:
Set (TL, BL)
and confirm (TR).
–
Minutes:
Set (TL, BL)
and confirm (TR).
iP1 SmartSystem – PersonalizediP1 SmartSystem
5.2.3 Stopwatch
+
–
Alarm clock on / off:
Set (TL, BL)
and confirm (TR).
The iW1 wristwatch has a stopwatch that can measure up to 99 hours and 59 minutes. The maximum accuracy of the stop watch is 1 second, and once 59 minutes and 59 seconds is exceeded,
it will only continue to measure hours and minutes. To use the stopwatch, complete the following
steps:
1. Beginning with the standard display, press the bottom right button three times to bring up
the stopwatch menu.
2. To start and stop the stopwatch, press the middle right button.
3. To reset the stopwatch, press the middle right button for three seconds.
4. While the stopwatch is running, the iW1 wristwatch will remain on the stopwatch menu. To
return to the standard display and leave the stop watch running in the background, press the
bottom right button.
OK
Standard display
appears.
27
Loading...