Armasight Prometheus 336 3-12x50 30Hz User manual

ARMASIGHT by FLIR

USER MANUAL

®

PROMETHEUS

Thermal Imaging Monocular

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

ARMASIGHT by FLIR

PROMETHEUS

USER MANUAL

© 2018 FLIR Systems, Inc. All rights reserved worldwide. No parts of this manual, in whole or in part,
may be copied, photocopied, translated, or transmitted by any electronic medium or in machine-readable
form without the prior written permission of FLIR Systems, Inc.

Names and marks appearing on the products herein are either registered trademarks or trademarks of
FLIR Outdoor & Tactical Systems and/or its subsidiaries. All other trademarks, trade names, or company
names referenced herein are used for identification only and are the property of their respective owners.

This product is protected by patents, design patents, patents pending, or design patents pending.
If you have questions that are not covered in this manual, or need service, contact FLIR OTS customer

support for additional information prior to returning a product.

2

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

ARMASIGHT by FLIR

PROMETHEUS

USER MANUAL

PROPER DISPOSAL OF ELECTRICAL AND ELECTRONIC EQUIPMENT (EEE)

The European Union (EU) has enacted Waste Electrical and Electronic Equipment Directive 2002/96/EC
(WEEE), which aims to prevent EEE waste from arising; to encourage reuse, recycling, and recover y of
EEE waste; and to promote environmental responsibility.

In accordance with these regulations, all EEE products labeled with the “crossed out wheeled bin” either
on the product itself or in the product literature must not be disposed of in regular rubbish bins, mixed
with regular household or other commercial waste, or by other regular municipal waste collection means.
Instead, and in order to prevent possible harm to the environment or human health, all EEE products
(including any cables that came with the product) should be responsibly discarded or recycled.

To identify a responsible disposal method where you live, please contact your local waste collection
or recycling service, your original place of purchase or product supplier, or the responsible government
authority in your area.

Business users should contact their supplier or refer to their purchase contract.

IMPORTANT INSTRUCTIONS AND NOTICES TO THE USER:

Modification of this device without the express authorization of FLIR Commercial Systems, Inc. may void
the user’s authority under FCC rules to operate this device.

Note 1: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation.

This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that the interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:

• Reorient or relocate the receiving antenna

• Increase the separation between the equipment and receiver

• Connect the equipment into an outlet on a circuit different from
that of the receiver

• Consult the dealer or an experienced radio/television technician for help.

INDUSTRY CANADA NOTICE:

This Class B digital apparatus complies with Canadian ICES-003.

AVIS D’INDUSTRIE CANADA:

Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.

3

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

ARMASIGHT by FLIR

PROMETHEUS

USER MANUAL

LIST OF CONTENTS

TITLE PAGE

Safety Summary 5

SECTION 1. IN TRODUCTION 6

1.1 Purpose of Equipment 6

1.2 Warranty Information and Registration 6

SECTION 2 . DESCRIPTION A ND DATA 8

2.1 System Description 8

2.2 Specifications 10

2.3 Standard Components 13

2.4 Optional Equipment 14

2.5 Key Features 15

SECTION 3. OPERATING INSTRUCTIONS 16

3.1 Installation and Connecting 16

3.2 Controls and Display Indications 18

3.3 Operating Procedures 26

SECTION 4 . MAIN TENA NCE AND TROUBLESHOOTING 29

4.1 Preventive Maintenance Checks and Services 29

4.2 Operator Troubleshooting 31

4.3 Maintenance 33

APPENDIX 35

List of Spare Parts 35

4

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

ARMASIGHT by FLIR

PROMETHEUS

USER MANUAL

SAFETY SUMMARY

• Read and follow all instructions

• Read all warnings

• Only use the attachments/accessories specified by the manufacturer

• All service must be provided by the manufacturer

WARNING:

DO NOT DISASSEMBLE THE DE VICE. Disassembly can cause permanent damage.

WARNING:

This product contains natural rubber latex which may cause allergic reactions! The FDA has

reported an increase in the number of deaths that are associated with an apparent sensitivity to natural
latex proteins. If you are allergic to latex, it is a good idea to learn which products contain it and strictly
avoid exposure to those products.

CAUTION:

Use of controls or adjustments or performance of procedures other than those specified herein may result
in hazardous radiation exposure.

CAUTION:

• Do not point the camera at high-intensity radiation sources such as the sun, lasers, or arc welders

• Do not leave fingerprints on the camera’s infrared optics. Clean only with low pressure fresh water
and a lens cloth

• Keep the equipment clean. Protect it from moisture, dramatic temperature drops, and electrical
shocks

• DO NOT force the equipment controls past their stopping points

• DO NOT leave the equipment activated during breaks in operation

• DO NOT store the equipment with the batteries installed

• Thoroughly clean and dr y each item before placing them into the storage case

NOTES:

• To avoid losing unsaved data, DO NOT remove the batteries or disconnect the external power
source while the Prometheus is on

• Inadver tent sun damage is not considered a defect in material or workmanship, and is therefore not
covered in the product warranty

5

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

ARMASIGHT by FLIR

PROMETHEUS

USER MANUAL

SECTION

1

INTRODUCTION

1.1 PURPOSE OF EQUIPMENT

The Prometheus is a solid state, uncooled, long-wave infrared, magnified, dedicated handheld thermal imager
intended for day and night engagements.

The Prometheus is based on the FLIR Tau 2 VOx microbolometer core. The 24/7 mission capability is only one
of the strengths of Prometheus. The thermal imaging technology also allows you to detect targets by cutting
through snow, dust, smoke, fog, haze, and other atmospheric obscurants. Unlike the use of laser targeting or
near infrared illumination to augment Night Vision equipment, the Prometheus thermal imager is extremely
difficult to detect with other devices, as it emits no visible light or RF energy.

The Prometheus is available in different versions, with 2x or 3x optical magnification. Prometheus series also
provides up to 8x digital zoom for models based on 640x512 cores and up to 4x digital zoom for models based
on a 336x256 core.

The Prometheus is powered by two CR123A (2×3V) batteries. The Extended Battery Pack or 6VDC/ 600mA
power source can also be used to power the Prometheus.

The Prometheus can be controlled by a wireless remote control.
The Prometheus is equipped with a standard NTSC/PAL video input/output function that makes it possible to

connect to an external video display or monitor, or to record thermal images for field documentation or training
purposes. It also allows the transmission of data from one remote display to that of the Prometheus.

The Prometheus can be used in conjunction with other equipment such as the Digital Video Recorder or
Extended Battery Pack that can be mounted onto the Prometheus’ Picatinny/ Weaver rail.

Extremely reliable and versatile, the Prometheus is a highly useful thermal imaging system.

1.2 WARRANTY INFORMATION AND REGISTRATION

1.2.1 WARRANTY INFORMATION

1.2.2 PRODUCT REGISTRATION

In order to validate the warranty on your product, the Customer must complete and submit FLIR Outdoor
& Tactical Systems’ PRODUCT REGISTRATION FORM on our website (

6

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

ARMASIGHT by FLIR

PROMETHEUS

USER MANUAL

SECTION

2

DESCRIPTION AND DATA

2.1 SYSTEM DESCRIPTION

The Prometheus consists of next primary parts: a body, a lens assembly and an eyepiece assembly.
The Prometheus is a thermosensitive device. It senses the differences in heat emitted by objects in its

field of view, and converts the received temperature pattern into a viewable image that represents the
scene in contrasting black & white or color patterns, depending on the user’s selected image palette.

FIGURE 2-1. PROMETHEUS THERMAL IMAGING MONOCULAR

NOT E:

It is important that the Prometheus sensor receive sufficient thermal contrast between the target
and background area, or between the different parts of a target. For example, the vast temperature
contrast between the snow and any heat target (such as an animal) makes it very easy to distinguish
the target.

The main optical-electronic components of the Prometheus include: an objective Germanium thermal
lens, eyepiece, a thermal-imaging camera, a display, a control card, and a button control panel.

The Prometheus is equipped with manual eyepiece and objective lens focusing.

8

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

ARMASIGHT by FLIR

PROMETHEUS

USER MANUAL

To accommodate individual user needs, the Prometheus has a variety of digitally controlled options
such as:

• Display Brightness

• Digital Zoom

• Palette Color Selection

• User-Controlled Manual Non-Uniformity Correction/ Flat-Field Correction (UCMNUC/ FFC)

• Imaging Enhancements

• Custom Settings

All Prometheus devices are based on FLIR Tau 2.7.2 or later cameras that allow for improvements in
overall image quality in a wide range of dynamic thermal environments. The Prometheus has employed
special user-adjustable imaging tools that include:

•

Active Contrast Enhancement (ACE) – a digital “Contrast” correction that allows for smart

scene optimization based on dynamic adjustments, where a variety of contrast levels occur
depending on relative scene temperature.

•

Second Generation Digital Detail Enhancement (DDE) – a “Sharpness” correction that

digitally enhances the picture, significantly sharpens edges, and further reduces image noise.

•

Smart Scene Optimization (SSO) – a fine-tuning computational correction that significantly

improves overall visual acuity for targets that have thermal signatures similar to the surrounding
background.

•

Automatic Gain Control (AGC) – a “Gain” correction that used to automatically adjust the gain

to an appropriate range, the weaker the image signal, the stronger the gain.

•

User-Controlled Manual Non-Uniformity Correction/ Flat-Field Correction (UCMNUC/

FFC). There is a mechanical shutter between the camera sensor and the lens. This shutter is used

to perform a non-uniformity correction (NUC), also known as flat-field correction (FFC). During FFC,
the shutter presents a uniform temperature source to each detector element in the array. While
imaging the flat-field source, the camera updates the offset correction coefficients, resulting
in a more uniform image after the process is complete. All Prometheus models allow for user to
manually trigger or interrupt scheduled UCMNUC/ FFC function.

•

Silent Shut terless NUC™ (SSN) – In addition to User-Controlled Manual NUC/ FFC, all

Prometheus models employ a digital, supplemental, non-mechanical flat-field correction that
extends periods between mechanical shutter events and further reduces image noise. SSN is an
always ON enhancement.

Information on the current operating state (battery status, active function in the display etc.) is
continuously displayed, making field operation of the Prometheus simple and convenient.

Manufactured for exceptional durability, the Prometheus has a lightweight and robust aluminum body.
A side Picatinny/ Weaver rail allows for the installation of an optional Digital Video Recorder, extended
battery pack, or other equipment.

9

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

ARMASIGHT by FLIR

PROMETHEUS

USER MANUAL

A standard NTSC/PAL video input/ output connector enables an external video display (monitor/ TV) or
video recorder to be connected to the Prometheus. An external 6VDC/600mA power source can also be
connected to the Prometheus.

The Prometheus is powered by two CR123A (2×3V) batteries.
Figure 2-2 shows the Prometheus. The ITEM NO. column of Table 2-1 indicates the number used to

identify items in Figure 2-2.

5

4

3

2

6

7

10

12

11

13

1

FIGURE 2-2. PROMETHEUS THERMAL IMAGING MONOCULAR. SYSTEM DESCRIPTION

8

9

14

TABLE 2-1. SYSTEM DESCRIPTION

ITEM DESCRIPTION ITEM DESCRIPTION

1 Objective Lens Cap 8 Eyepiece

2 Objective Lens 9 Battery Cap

3 Objective Focus Ring 10 Turn-Pull Switch

4 Body 11 Connector Cap

5 Button Control Panel 12 Connector

6 Eyepiece Focus Ring 13 Side Picatinny/ Weaver Rail

7 Eyecup 14 Tripod Socket

2.2 SPECIFICATIONS

TABLE 2-2. SYST EM DATA

ITEM PROM ETHEUS 3 36 3 -12×50 PROM ETHEUS 6 40 2-16×5 0

Optical Magnification
(NTSC/ PAL)

Objective Lens Type Germanium

Focal Plane Array FLIR Tau 2

Frame Rate 9 Hz, or 30 Hz, or 60 Hz 30 Hz

2.8× / 3.4× 1.5× / 1.8 ×

10

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

ARMASIGHT by FLIR

PROMETHEUS

USER MANUAL

TABL E 2-2. CON TINUED

ITEM PROM ETHEUS 3 36 3 -12×50 PROM ETHEUS 6 40 2-16×5 0

Pixel Array Format 336×256 640× 512

Pixel Size 17 µm

Display Type OLED SVGA

Pixel Display Format 800×600

Display Brightness Discretely Adjustable to 8 Levels

Turn-on Time, max 3 sec

Digital Zoom 2×, 4× 2×, 4×, 8×

Temperature Imaging Modes
(Image Palettes)

User-adjustable
Image Enhancement
Tools

Analog Video Input/ Output
Format (resolution)

*Default setting (may be altered at the customer’s request).

ITEM PROM ETHEUS 3 36 3 -12×50 PROM ETHEUS 6 40 2-16×5 0

Field of
View

Objective Focal Length

Objective F-number

Exit Pupil Diameter

Eye Relief

Focus Method

Focusing Range

Diopter Adjustment

Diopter Adjustment Range

- ang. X (degrees) 7.8 14.8

- ang. Y (degrees)

White Hot, Black Hot, Fusion, Rainbow, Globow, Ironbow1, Ironbow2,

Sepia, Color1, Color2, Ice-Fire, Rain, and OEM

• Active Contrast Enhancement (ACE) - “CONTRAST”

• Second Generation Digital Detail Enhancement (DDE) –

“SHARPNESS”

• Smart Scene Optimization (SSO) – “SMART SCENE”

• Automatic Gain Control - “GAIN”

• User-Controlled Manual Non-Uniformity Correction/

Flat-Field Correction (UCMNUC/ FFC)

• Silent Shutterless NUC ™ (SSN)

PAL (768×574 pixels)* / NTSC (640×480 pixels)

TABLE 2-3 . OP TICAL DATA

5.9 11.8

50mm

1:1

14 mm

25 mm

Manual

5m to inf.

Manual

±5 diopter

11

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

ARMASIGHT by FLIR

PROMETHEUS

USER MANUAL

TABLE 2-4. ELECTRICAL DATA

ITEM DATA

Battery Two CR123A 3V Lithium batteries or CR123 type rechargeable

Current Consumption, maximum 320 mA

Battery Life at 20°C (68 °F) Up to 4 hrs (up to 12 hrs with optional extended battery pack)

Extended Battery Pack (optional) Two 18650 rechargeable batteries (3.7V), four CR123

External Power Supply 6 VDC/ 600mA

ITEM DATA

Overall Dimensions

Weight (w/o Batteries)

ITEM DATA

Operating Temperature -40 to +50°C (-40 to +122°F)

Storage Temperature -50 to +70°C (-58 to +158°F)

Environmental Rating Water and Fog-Resistant

TABLE 2-7. ADVANCED WIRELESS REMOTE CONTROL (AWREC) DATA

ITEM DATA

Type Wireless Remote Control

Working Range Up to 0.5m

Battery Single CR2032 Lithium battery (3V)

Battery Life at 20 °C (68 °F) Approx. 10,000 clicks

Overall Dimensions 48 × 39 × 18 mm (1.9 × 1.5 × 0.7 in)

Weight (with Battery) 25 g (0.9 oz)

Operating Temperature -30 to +50°C (-22 to 122°F)

Storage Temperature -50 to +70°C (-58 to 158°F)

Environmental Rating Water and Fog-Resistant

batteries with voltage from 3.0V to 3.7V (2)

rechargeable batteries with voltage 3.7V max, or four standard
CR123A 3V Lithium batteries (operational time up to 8 hr)

TABLE 2-5. MECHANICAL DATA

238 × 73 × 65 mm (9.3 × 2.8 × 2.5 in)

0.55 kg (1.2 lbs)

TABLE 2-6 . ENVIRONMENTAL DATA

12

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

ARMASIGHT by FLIR

PROMETHEUS

USER MANUAL

2.3 STANDARD COMPONENTS

The Prometheus standard components are shown in Figure 2-3 and listed in Table 2-8.
The ITEM NO. column indicates the number used to identify items in Figure 2-3.

3

1

2

FIGURE 2-3. STANDARD COMPONENTS

4

8

5

6

9

TABLE 2-8. STANDARD COMPONENTS

ITEM

NO.

DESCRIPTION

1 Prometheus Thermal Imaging Monocular

A thermal imaging device.

2 Objective Lens Cap

Securely protects the objective lens from dirt and mechanical damage and provides
thermal protection of the Prometheus. Comes attached to the objective lens.

3 Eyecup

A specially designed latex eyecup that reduces the amount of light that escapes
from the eyepiece and prevents illumination of the user’s face, minimizing the risk of
detection. Prevents ambient light from entering the equipment. Allows for correct
and comfortable positioning. Comes attached to the eyepiece.

4 Battery Cassette

Intended for the installation of two CR123 batteries in the battery compartment. The
Prometheus comes with two battery cassettes (includes one installed in the battery
compartment and one spare cassette).

7

10

QUAN-

TITY

1

1

1

2

5 CR123A Lithium Battery

2

Two CR123A batteries are used to power the Prometheus.

6 Advanced Wireless Remote Control (AWREC)

1
Allows the user to operate the Prometheus in short-time activation mode. Ensures
quick and silent activation/deactivation of the equipment. Comes with CR2032 (3V)
batter y installed.

13

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

ARMASIGHT by FLIR

PROMETHEUS

USER MANUAL

TABL E 2-2. CON TINUED

ITEM

NO.

DESCRIPTION

7 Picatinny Adapter for Advanced Wireless Remote Control

Allows the advanced wireless remote control to be installed on a Picatinny/Weaver
rail.

QUAN-

TITY

1

8 Video Cable

A cable used to connect the analog video input/output of the Prometheus to external
display devices (monitor/ TV) or power sources. Supported input and output video
formats include PAL and NTSC.

9 Operation and Maintenance Manual

Provides safety information, equipment description, mounting procedures, operating
instructions, and preventive maintenance checks and services.

10 Carrying Case

A textile bag used for the transportation and storage of the Prometheus and its
accessories.

2.4 OPTIONAL EQUIPMENT

Optional items are shown in Figure 2-4 and listed in Table 2-9.

1

2

FIGURE 2-4. OPTIONAL EQUIPMENT

1

1

1

3

4

The ITEM NO. column indicates the number used to identify items in Figure 2-4.
The PART NO. column indicates the primary number used by the manufacturer, to identify an item.

TABLE 2-9. OPTIONAL EQUIPMENT

ITEM

NO.

1 HD DVR Digital Video Recorder

DESCRIPTION PART NO.

ATAM000005
High Definition Digital Recorder for all High Per formance Digital and Thermal
Devices.

14

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

ARMASIGHT by FLIR

PROMETHEUS

USER MANUAL

TABL E 2-2. CON TINUED

ITEM

NO.

2 E xtended Battery Pack

The power source for extended operational time. Takes four CR123A Lithium
batteries (3V), CR123 rechargeable batteries (3.2V or 3.7V), or t wo 18650
rechargeable batteries (3.7V).

DESCRIPTION PART NO.

ATAM000008

3 Hard Shipping/ Storage Case

A protective case used for the shipping/storage of the Prometheus and its
accessories.

3 Tripod with a Grip

Lightweight and compact tripod used to produce a stable image for long
range observation or photo shoot with long exposures.

ANHC000001

ANAMTM0003

2.5 KEY FEATURES

• Multiple versions with 2 x or 3x optical magnification

• High-performance thermal imaging camera

• Lightweight and robust design

• Easy to operate

• Manually adjustable eyepiece and objective lens

• Real-time display

• Digitally controlled features

• Current operational state information display (battery status, active profile, palette
setting)

• Wireless remote control

• Analog video input and output (NTSC/ PAL)

• Powered by two standard CR123A bat teries

• Power input capability

• Digital video recorder (optional)

• Serviceability under severe conditions

• Filled with dry nitrogen to prevent internal fogging

• Limited 3-year warranty

• 10-year warranty on FLIR detector

15

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

ARMASIGHT by FLIR

PROMETHEUS

USER MANUAL

SECTION

3

OPERATING INSTRUCTIONS

3.1 INSTALLATION AND CONNECTING

3.1.1 BATTERY INSTALLATION

CAUTION:

Verify that the equipment is OFF before installing the batteries.

To install two CR123A batteries (refer to Figure 3-1):

1. Unscrew the battery cap (A).

2. Remove the battery cassette (B).

3. Insert the batteries (C) into the cassette. Align the polarity symbols on the batteries with the
polarity symbols on the cassette.

4. Insert the cassette with installed batteries.

5. Replace the battery cap.

A

C

B

FIGURE 3-1. BATTERY INSTALLATION

3.1.2 FASTENING AN ADVANCED WIRELESS REMOTE CONTROL

Using the supplied Velcro tape (A, Figure 3-2), fasten the remote control (B) to an easily accessible place.
You can use the Picatinny adapter for the Advanced Wireless Remote (C) for mounting the remote control

to Picatinny or Weaver rail. Install the adapter onto the rail (D). Insert the remote control into the adapter.

16

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

ARMASIGHT by FLIR

PROMETHEUS

USER MANUAL

B

B

A

FIGURE 3-2. ADVANCED WIRELESS REMOTE CONTROL

C

D

3.1.3 INSTALLING ADDITIONAL EQUIPMENT

Use the side Picatinny/ Weaver rail to install any additional equipment, such as the Digital Video
Recorder or the Extended Battery Pack.

3.1.4 CONNECTING AN ADDITIONAL EQUIPMENT

CAUTION:

Turn off the Prometheus before you begin connecting/ disconnecting any external equipment and
before removing the batteries.

Remove the connector’s protective cap.
Connect the cable of Digital Video Recorder or the Extended Battery Pack to the Prometheus connector.

FIGURE 3-3. DIGITAL RECORDER DT INSTALLATION

Use plug A (Figure 3-4) of the video cable to connect an external video recorder/ monitor/ TV to the
Prometheus. Connect plug C of the video cable to the Prometheus connector.

Use plug B of the video cable to connect an external power source (6VDC/ 600mA) to the Prometheus.
Connect plug C of the video cable to the Prometheus connector.

17

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

ARMASIGHT by FLIR

PROMETHEUS

USER MANUAL

C

A B

FIGURE 3-4. VIDEO CABLE

NOTE:

The external power supply must have a standard OD double-pole socket with a positive center
contact.

CAUTION:

After removing the cable, replace the protective cap over the connector.

3.1.5 INSTALLING THE PROMETHEUS ON A TRIPOD

To mount the Prometheus to a tripod, screw the tripod into the 1/4’’ threaded socket located on the
bottom of the Prometheus.

CAUTION:

The unit may be badly damaged if the tripod collapses or falls over. Remove the unit from the tripod
if it is not within your reach.

3.2 CONTROLS AND DISPLAY INDICATIONS

3.2.1 CONTROLS

CAUTION:

DO NOT force the equipment controls past their stopping points.

The Prometheus controls are shown in Figures 3-5 and 3-6 and are defined in Tables 3-1 and 3-2. The
ITEM NO. columns indicate the numbers used to identify items in the figures.

NOTE:

Various display symbols indicating the current operating state of the Prometheus can be displayed
permanently, may appear momentarily, or can be set to appear only when a certain function is
activated.

18

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

ARMASIGHT by FLIR

PROMETHEUS

USER MANUAL

4

3

2

1

5

FIGURE 3-5. CONTROLS

TABLE 3-1. CONTROLS AND INDICATORS

ITEM

CONTROL / INDICATOR FUNCTION

NO.

1 Eyepiece Focus Ring Adjusts the eyepiece diopter. The total diopter adjustment range is

covered with 2 turns of the ring.

2 Turn-Pull Switch Activates the Prometheus when turned ON.

NOTE:

You must pull the knob before turning in order to use either ON or
STB.

Activates standby mode when turned to STB (see note above).

Deactivates the Prometheus when turned OFF.

3 Control Panel Buttons Configures operational settings. See Table 3-2 for button functions.

4 Objective Focus Ring Focuses the objective lens. Adjusts for sharpest view of the scene.

The total focus range is covered with three quarter turns of the lens.

5 Remote Control

Button

Activates/ deactivates the Prometheus in standby mode. To turn the
unit on, press button once, to turn it off – press button again.
To operate the device in short-time activation mode, press and
hold the remote control button down for 1.5+ seconds. Release the
remote control button to deactivate the device.

— Battery Status Indicator

(battery icon in the top
right hand corner of the
display)

The color fill (green/ yellow/ red) bar in the battery icon indicates the
current power level of the internal battery, or remaining battery life.

The totally shaded battery icon indicates the fully charged battery.

The flashing transparent battery icon indicates a low battery.

19

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

ARMASIGHT by FLIR

PROMETHEUS

USER MANUAL

TABL E 3-1. CONT INUE D

ITEM

CONTROL / INDICATOR FUNCTION

NO.

— Image Palette Indicator

(in the top left hand
corner of the display)

Indicates the selected image palette.

— Digital Zoom Indicator

(in the top center of the

Indicates the current value of digital zoom when 2x or 4x zoom
activated.

display)

The Prometheus button control panel is shown in Figure 3-6.
Table 3-2 contains the button functions and their brief descriptions. The ITEM NO. column of the table

indicates the number used to identify buttons in Figure 3-6.

NOTE:

Each button is responsible for some functions selected by briefly pushing or holding down the
button, or using the button in combination with a second one (as described in Table 3-2).

Pushing a button for 1.5+ second is considered “holding down.”

1

3

2

FIGURE 3-6. BUTTON CONTROL PANEL

TABLE 3-2. BUTTON CONTROLS

ITEM

NO.

FUNCTION DESCRIPTION

DISPLAY BRIGHTNESS

Push button (1) to increase the screen brightness.

INCREASE

1

DIGITAL ZOOM CONTROL To change the zoom gradually, push and hold button (1).

UP Use the UP (1) button to navigate through the items on the menu.

20

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

ARMASIGHT by FLIR

PROMETHEUS

USER MANUAL

TABL E 3-2. CONTINUED

ITEM

NO.

FUNCTION DESCRIPTION

DISPLAY BRIGHTNESS

Push button (2) to decrease the screen brightness.

DECREASE

2

IMAGE PALETTE
CONTROL

To scroll through the available palettes, hold down button (2).
There are 13 palettes available: White Hot, Black Hot, Fusion,
Rainbow, Globow, Ironbow1, Ironbow2, Sepia, Color1, Color2, Ice­Fire, Rain, and OEM.

DOWN Use the DOWN (2) button to navigate through items on the menu.

USER-CONTROLLED
MANUAL NON­UNIFORMITY

1 + 2

CORRECTION/ FLAT-FIELD

Simultaneously holding down buttons (1) and (2) induces
User-Controlled Manual Non-Uniformity Correction/ Flat-Field
Correction (UCMNUC/ FFC).

CORRECTION (UCMNUC/
FFC)

Holding down button (3) will bring up the Main Menu. The menu

MENU

includes the following functions: Palette, Enhancement, and
Settings.

3

SELECTION

Push the SELECTION button (3) to view the settings available for
the item selected.

To enable left and right navigation (< >) press button (3).

UCMNUC/ FFC PROCESS
INTERRUPTION

Pushing button (3) when the countdown is on the screen will
cancel the UCMNUC/ FFC , and the shutter will not interrupt
viewing.

3.2.2 MAIN MENU

Most setup options can be accessed from the MAIN MENU.
To display the MAIN MENU, hold down button (3) on the control panel (Figure 3-6).
Once the MAIN MENU is displayed (Figure 3-7), use buttons (1) and (2) to navigate through items on the

menu.
Push button (3) to view the settings available for the item selected.

MAIN MENU

> EXIT
PALE TT E
ENHANCEMENT
SETT INGS

FIGURE 3-7. MAIN MENU

21

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

ARMASIGHT by FLIR

PROMETHEUS

USER MANUAL

NOTE:

Navigate through sub-menu items by pushing buttons (1) and (2), except where otherwise indicated.
After a menu item is selected, push button (3) to activate the selected function. The function will

either be activated or will show <> symbols.
When <> symbols are shown on the menu, the left and the right actions are required. Use button (1)

to increase (>) the value, and button (2) to decrease (<) the value. To enter the value and disable left
and right navigation, press button (3).

Select EXIT and push button (3) to return to the MAIN MENU.

PAL ETTE MENU

The PALETTE menu (Figure 3-8 and Figure 3-9) allows you to select from a range of temperature imaging
modes: White Hot, Black Hot, Fusion, Rainbow, Globow, Ironbow 1, Ironbow 2, Sepia, Color 1,
Color 2, Ice-Fire, Rain, and OEM Custom.

NOTE:

To navigate through the items on the two-page PALETTE menu, hold down button (1) or button (2).

The palettes act as color templates for visualization of temperature changes.
To navigate through the items on the PALETTE menu, press buttons (1) or (2).

PALE TT E

> EXIT
WHITE HOT
BLACK HOT
FUSION
RAINB OW
GLOBOW
IRONBOW 1
IRONBOW 2

FIGURE 3-8. PALETTE MENU

PALE TT E

> EXIT
SEPIA
COLOR 1
COLOR 2
ICE-F IRE
RAIN
OEM CUSTOM

FIGURE 3-9. PALETTE MENU. CONTINUED

22

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

ARMASIGHT by FLIR

PROMETHEUS

USER MANUAL

NOTE:

The most popular palettes are White Hot and Black Hot, usually known as inversion. White Hot
mode is ideal for spotting targets, while Black Hot is most useful for situational reading.

NOTE:

Training and experience are required to quickly and properly interpret thermal images.

ENHANCEMENT MENU

The ENHANCEMENT menu (Figure 3-10) allows users to take advantage of advanced signal processing
algorithms to improve image quality under a variety of different thermal environments.

ENHANCEMENT

> EXIT
CO NTRAS T <> 4
SHARPNESS <> 60
SM ARTSCEN E <> 15
GA IN <> 35
AGC S PEED <> 12

FIGURE 3-10. ENHANCEMENT MENU

CONTRAST - Active Contrast Enhancement (ACE) – a digital contrast correction that allows for a smart
scene optimization based on dynamic adjustments, where a variety of contrast levels occur depending on
relative scene temperatures. The adjustment range is from -8 to +8 with a default value of 4. Lower
values will cause hotter objects to have greater contrast, and higher values will cause colder objects to
have more contrast.

CON TR AST -8 CON TR AST +8

FIGURE 3-11. DIGITAL CONTRAST CORRECTION

23

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

ARMASIGHT by FLIR

PROMETHEUS

USER MANUAL

SHARPNESS - Second Generation Digital Detail Enhancement (DDE) – a sharpness correction that
digitally enhances the picture, significantly sharpens the image, and further reduces image noise. The
adjustment range is from -20 to +100 with a default value of 60. Lower values soften image edges. Higher
values will sharpen the image, enhance details, and further increase the signal-to-noise ratio.

SHA RPNESS -20 SHARPNE SS +10 0

FIGURE 3-12. SHARPNESS CORRECTION

SMART SCENE - Smart Scene Optimization (SSO) – a fine-tuning computational correction that
significantly improves overall visual acuity for targets that have thermal signatures similar to the
surrounding background. Higher values provide a more linear automatic gain control behavior and objects
with similar, but not identical, temperatures can be differentiated with greater accuracy. The adjustment
range is from 0 to 100 with a default value of 15.

SMA RT SCENE 0 SMA RT SCENE 100

FIGURE 3-13. SMART SCENE OPTIMIZATION

GAIN - Automatic Gain Control (AGC) – a correction that used to automatically adjust the gain to an
appropriate range, the weaker the image signal, the stronger the gain. The adjustment range is from 0 to
255 with default value 35.

AGC SPEED – parameter that allows user to control the refresh rate of Automatic Gain Control (AGC). The
adjustment range is from 0 to 128 with a default value of 12.

24

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

ARMASIGHT by FLIR

PROMETHEUS

USER MANUAL

GAIN 0 GAIN 3 5

FIGURE 3-14. GAIN CORRECTION

SETTINGS MENU

The SETTINGS menu (Figure 3-15) allows for direct changes to Video Standards and Factory Default
settings.

The Firmware (FW) revision number is listed at the bottom of the menu display.

SETTINGS

> EXIT
STANDARD
FACTORY R ESE T
FW: XXXXXXXXXX

FIGURE 3-15. SETTINGS MENU

STANDARD
Changes the video output standard between NTSC and PAL.
FACTORY RESET
Resets the camera to factory defaults.
SOFTWARE VERSION
Software release is shown in alphanumeric format. When the SELECT button is pushed, the FW

(firmware) version will appear.

NOTE:

After configuration is complete, select EXIT on the MAIN MENU and push button (3). All settings
will be saved.

25

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

ARMASIGHT by FLIR

PROMETHEUS

USER MANUAL

3.3 OPERATING PROCEDURES

3.3.1 OPERATING

CAUTION:

DO NOT force the equipment controls past their stopping points.

CAUTION:

To prevent thermal damage to the equipment, never point it, either powered or not, directly at the
sun or any other source of high intensity light that the unprotected human eye cannot tolerate (such
as a welding arc). To prevent inadvertent exposure to these sources, never leave the equipment
without the objective lens cap secured.

Operating procedures are as follows:

1. Remove the Prometheus from the carrying case.

2. Remove the objective lens cap.

3. Point the equipment at an object.

4. Activate the Prometheus by turning the turn-pull switch ON. After approximately 3 sec, video of the
thermal scene should appear.

5. Adjust the Prometheus for your eyesight by turning the eyepiece focus rings CW up to the stop,
and then CCW until the display and symbols are as clear as possible. Bring the object into focus by
turning the objective focus ring (CW for far focus, CCW for near focus).

NOTE:

The total diopter adjustment range is covered with 2 turns of the eyepiece focus ring.
The total focus range is covered with three quarter turns of the objective focus ring.

BRIGHTNESS INCR EA SE /
ZOO M (1)

MENU / SEL ECTION /
UCMNUC/FFC PROCESS INTERRUPTION (3)

BRIGHTNESS DECR EASE /
IMAGE PALETTE (2)

FIGURE 3-16. SETTING BUTTONS

26

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

ARMASIGHT by FLIR

PROMETHEUS

USER MANUAL

6. Using the buttons on the control panel (Figure 3-16), configure the Prometheus to adapt it to your
situation.

For more information on operational setting procedures, see Part 3.2 (Controls and Display Indications).

A. Adjust the brightness of the display for your comfort.

Push buttons (1) and (2) to increase/ decrease the display brightness by one level at a time

until you reach your desired brightness level.

B. Use UCMNUC/ FFC (User-Controlled Manual Non-Uniformity Correction/ Flat-Field Correction)

to improve image quality.

Push buttons (1) and (2) simultaneously to start manual UCMNUC/ FFC.

If necessary, interrupt the automatic process by pushing the central button (3) on the control

panel during the 5-second countdown, which will appear at the bottom of the display.

C. Use the digital zoom to magnify the central area of the image.

Hold down button (1) to gradually zoom in on the image. The 2x, 4x, and 8x symbols (maximum

zoom factor is dependent on equipment model) will appear in the top part of the display.

NOTE:

Digital zoom allows distant objects to appear larger; however, the resolution will be compromised.

D. Use the image palettes for optimal visualization of temperature changes in the scene.

Hold down the palette control button (2) to scroll through available palettes. The palette name

will appear in the top part of the display.

E. Adjust the necessary adjustment using the MAIN MENU. See Part 3.2.2 (Using the MAIN

MENU).

NOTE:

After configuration is complete, select EXIT on the MAIN MENU and push the SELECTION button to
leave the MAIN MENU. All settings will be saved.

10. To operate the Prometheus with Advanced Wireless Remote Control (AWREC), turn the function
switch to the STB position (Standby). After it the Remote Control button can activate/ deactivate
the device in two ways:

1) To turn the device on, press the remote control button once, to turn it off – press the button
again.

2) To operate the device in short-time activation mode (see note below), press and hold the
remote control button down for 1.5+ seconds. Release the remote control button to deactivate
the device.

27

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

ARMASIGHT by FLIR

PROMETHEUS

USER MANUAL

CAUTION:

DO NOT leave the equipment activated when not in use.

3.3.2 PROMETHEUS SHUT-DOWN

NOTE:

Shut down the Prometheus properly to avoid losing unsaved settings and data.

Shut-down the Prometheus as follows:

1. Be sure to save your settings and data.

2. Turn off the Prometheus.

3. Place the protective cap on the objective lens.

4. Disconnect the cable (if applicable).

5. Place the protective cap on the connector.

6. Remove the batteries.

CAUTION:

Do not store the Prometheus with the batteries still installed.

7. Store the Prometheus and all accessories in the carrying case.

28

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

ARMASIGHT by FLIR

PROMETHEUS

USER MANUAL

SECTION

4

MAINTENANCE AND
TROUBLESHOOTING

4.1 PREVENTIVE MAINTENANCE CHECKS AND SERVICES (PMCS)

Table 4-1 Preventive Maintenance Checks and Services (PMCS), has been provided so that you can keep
your equipment in good operating condition.

Perform functional tests in the order listed in Table 4-1.
Operating procedures are detailed in Chapter 3.

Explanation of Table Entries:
SEQ NO. column. Sequence numbers are for reference and appear in the order required to perform

checks and services.
LOCATION OF ITEM TO CHECK / SERVICE column. Indicates the location and the item to be checked

or serviced.

PROCEDURE column. Details the check/ service procedure.

NOT FULLY MISSION CAPABLE IF... column. Indicates what faults will prevent your equipment from

operating successfully.

TABLE 4-1. PREVENTIVE MAINTENANCE CHECKS AND SERVICES

LOCATION OF

SEQ

ITE M TO CHE CK /

NO.

SERVICE

1 Completeness Open storage/ carrying case and inventory

2 Soft Carrying

Case

3 Body Inspect for cracks or damage. Scratches and

items by comparing with the data in this
manual.

Shake out loose dirt or foreign material.
Inspect for tears, cuts, excess wear or
damage.

gouges are OK if operation is not affected.
Inspect for missing parts.
Clean as required.

PROCEDURE

PRE-OPERATION CHECKS

NOT FULLY MISSION

CAPABLE IF...

Missing items.

Cracked or damaged. Missing
parts.

29

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

ARMASIGHT by FLIR

PROMETHEUS

USER MANUAL

TABL E 4-1. CONT INUED

LOCATION OF

SEQ

ITE M TO CHE CK /

NO.

SERVICE

4 Objective Lens

Cap

Inspect for cuts, tears and dirt.
Clean as required.

PROCEDURE

5 Eyecup Inspect for cuts, tears and dirt. Inspect for

torn, bent or improperly fitting eyecup.
Clean as required.

6 Battery

Compartment
and Cap

Inspect for corrosion, moisture, and corroded
or defective contacts. Inspect for cap damage
or retainer breaks. Inspect rubber gasket for
damage.

7 Lenses Inspect for cleanliness, scratches, chips or

cracks.
Clean as required.

8 Objective Focus

Ring

Rotate objective focus ring to ensure it is not
too tight or too loose. Range is approximately
three quarter turns.

9 Eyepiece Focus

Ring

Rotate eyepiece focus ring to ensure the
ring is not too tight or too loose. Range is
approximately 2 turns.

10 Turn - Pull

Check for operation (without batteries). Switch is inoperative.

Switch

11 Connector Inspect for corrosion, moisture, and corroded

or defective contacts. Inspect for cap damage
or retainer breaks.

12 Remote Control

Unit

Check for damage and missing parts.
Check Velcro tape for wear.

13 Video Cable Inspect for damage. Inspect the cable

connector for corrosion, moisture, and
corroded or defective contacts. Clean as
required.

NOT FULLY MISSION

CAPABLE IF...

Cap is torn or cut. Cap is not
secured to the housing of the
lens.

Cup is torn or cut.

Contacts are damaged or
corroded. Retainer is broken.
Cap or rubber gasket is
damaged.

Chipped or cracked. Scratches
hinder vision through the
equipment.

Ring gets stuck, is too loose,
or adversely affects the user’s
ability to properly focus the
objective lens.

Ring get stuck, is too loose,
or adversely affect the user’s
ability to properly adjust the
diopter.

Contacts are damaged or
corroded. Cap is damaged.
Retainer is broken.

Damaged. Missing parts.

Damaged.

30

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

ARMASIGHT by FLIR

PROMETHEUS

USER MANUAL

TABL E 4-1. CONT INUED

LOCATION OF

SEQ

ITE M TO CHE CK /

NO.

SERVICE

PROCEDURE

NOT FULLY MISSION

CAPABLE IF...

OPERATIONAL CHECKS

NOTE:

For a complete operational check, it is necessary to connect a video monitor to the Prometheus.

14 Turn - Pull

Switch

Install the batteries. Remove the objective
lens cap. Point the equipment at an object.
Turn the equipment on. Look for a thermal

No thermal image. Battery
icon is flashing (indicates a low

battery).
image on the display. Look for a flashing
battery icon in the eyepiece viewing area.

15 Control Board

Ensure the Prometheus is responsive to

Unresponsive buttons.
control buttons.

16 Remote

Control

Turn the equipment to standby. Point the
equipment at an object. Push and hold the

No image.

remote control button. Look for a thermal
image on the display. Release the button.
Turn off the equipment.

17 Video Cable Connect an external monitor to the

No image.
Prometheus. Point the equipment on an
object. Turn the equipment on. Look for
an image on the monitor. Turn off the
Prometheus. Disconnect the monitor.

POST-CHECK PROCEDURES

Turn off the equipment.
Replace the objective lens cap.
Remove the batteries.
Return the equipment and all accessories to

the carrying case.

4.2 OPERATOR TROUBLESHOOTING

The purpose of troubleshooting is to identify the most frequent equipment malfunctions, probable causes,
and corrective actions required.

Table 4-2 lists the common malfunctions that may be found during the operation or maintenance of the
Prometheus. Perform the tests/inspections and corrective actions in the order listed.

This table does not list all of the malfunctions that may occur with your device, or all of the
tests and corrective actions that may be necessary. If you experience an equipment malfunction

that is not listed, or is not fixed by the corrective actions listed in the table, please contact Customer
Service center.

31

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

ARMASIGHT by FLIR

PROMETHEUS

USER MANUAL

TABLE 4-2. OPERATOR TROUBLESHOOTING

MALFUNC TION PROBABLE CAUSE/ TEST/INSPEC TION CORRECTIVE ACTION

The Prometheus fails to
activate.

The Prometheus is not
responsive to control
buttons.

Remote control does not
work.

Poor image quality. Check objective lens and

No image on an external
monitor.

Hindered rotation of the
battery cap.

Light is visible around
eyecup.

Batteries are missing or
improperly installed.

Batteries are dead. Replace the batteries.
Batteries, surfaces, or contacts

are dirty or corroded.

Remote control unit is damaged. Please contact Customer Support.
Remote control battery is dead. Replace the battery as per Part 4.3.4.
The equipment is damaged. Please contact Customer Support.
The equipment is damaged. Please contact Customer Support.

Battery is missing or improperly
installed.

Battery is dead. Replace the battery.

Battery surfaces or contacts are
dirty or corroded.

Remote control unit is damaged. Please contact Customer Support.

eyepiece focus.
Check for fogging or dirt on

objective lens and eyepiece.
The equipment is damaged. Please contact Customer Support.
Video cable is damaged. Replace the video cable with a new

The equipment is damaged. Please contact Customer Support.
Dirty cap thread. Clean the thread.
Damaged cap thread. Replace the cap with a new one. If

Check eyecup resilience. If the eyecup is defective, please

Insert batteries or install correctly.

Clean the contact surfaces with a
pencil eraser and/or alcohol and
cotton swabs.

Insert battery or install correctly.

Clean the contact surfaces with a
pencil eraser and/or alcohol and
cotton swabs.

Refocus.

Clean the lenses as detailed in Part

4.3.2.

one. If this is not effective, please
contact Customer Support.

this is not effective, please contact
Customer Support.

contact Customer Support.

32

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

ARMASIGHT by FLIR

PROMETHEUS

USER MANUAL

4.3 MAINTENANCE

4.3.1 GENERAL

The Prometheus operator maintenance consists of operational tests, inspections for unit serviceability,
cleaning and mounting procedures, and corrective actions (troubleshooting and replacement of a limited
number of parts). Maintenance instructions covered elsewhere in this manual (PMCS, troubleshooting,
etc.) are not repeated in this section.

CAUTION:

The Prometheus is a precision electro-optical instrument and must be handled carefully at all times
to prevent damage.

CAUTION:

DO NOT dismantle the equipment.

4.3.2 CLEANING PROCEDURES

Clean the Prometheus and optional items as follows:

1. Gently brush off any dirt from the equipment using only a clean, soft cloth.

2. Moisten the cloth with fresh water and gently wipe the external surfaces (except for optical
surfaces).

3. Dry any wet surfaces (except for optical surfaces) with another clean, dry soft cloth.

4. Using a lens brush, carefully remove all loose dirt from optical surfaces (objective lens and
eyepiece).

5. Dampen a cotton swab with ethanol and lightly and slowly wipe optical surface. Clean the optical
surface using circular movements, starting from the center and moving out towards the edge, not
touching the lens holder and changing the cotton swab after each circular stroke. Repeat until the
optical surface is clean.

6. Clean the battery contact surfaces and contact springs with a pencil eraser and/or alcohol and
cotton swabs.

CAUTION:

Thoroughly dry each item before replacing into the storage/carrying case.

33

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

ARMASIGHT by FLIR

PROMETHEUS

USER MANUAL

4.3.3 BATTERY REMOVAL AND REPLACEMENT

Refer to Part 3.1.1 for battery installation procedures.
Replace the remote control battery as follows:

1. Using a screwdriver, unscrew the four screws (A, Figure 4-1) that secure the cover to the bottom of
the unit. Remove the cover.

A

FIGURE 4-1. ADVANCED WIRELESS REMOTE CONTROL BATTERY INSTALLATION

2. Replace the battery with new one (CR2032, 3V). Install the battery, aligning their polarity markings
(+/-) with those embossed on the compartment.

3. Replace the cover and tighten the screws (A).

34

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

ARMASIGHT by FLIR

PROMETHEUS

USER MANUAL

APPENDIX

LIST OF SPARE PARTS

The parts authorized by this list of spare parts are required for operator maintenance. The list includes
parts that must be removed before replacing authorized parts.

The PART NO. column indicates the primary number used by the manufacturer, which controls the design
and characteristics of the item in terms of its engineering drawings, specifications, standards, and
inspection requirement, to identify an item.

6

5

4

3

2

1

FIGURE A-1. PROMETHEUS SPARE PARTS LIST

7

9

10

13

11

14

12

TABLE A-1. PROMETHEUS SPARE PARTS LIST

ITE M NO. DESCRIPTION PART NO.

1 Objective Lens Cap APRMOLC50
2 Objective Lens Assembly APRMOLA50
3 Connector Cap APRMCNCP
4 Battery Cap APRMBC
5 Turn-pull Switch APRMSWT
6 Eyepiece Assembly APRMEPA
7 Eyecup APRMEC
8 Side Picatinny/ Weaver Rail (not shown) APRMRRL

9 Battery Cassette ARRMBTCS
10 Advanced Wireless Remote Control ANVR000001
11 Picatinny Adapter for Advanced Wireless Remote Control ANRA000002
12 Operation and Maintenance Manual APRMOMM
13 Video Cable APRVCBL
14 Carrying Case APRMCCS

35

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com