Page 1
PVS-14/6015
Night Vision Monocular
OPERATION AND
MAINTENANCE MANUAL
Impor tant Export Res trictions ! Co mmodities, produ cts, technologi es and ser vices of thi s manu al are contro lled by the U.S.
Depar tment o f State Oce of De fense Trade Controls, in accordance with International Trac in Arms (ITAR), Title 22, Code of
Federal Regulati ons Part 120-130 and/or by the Expor t Administration Re gulations (EAR) of U.S. Depar tment of Commerce. At any
time whe n a license or a wri tten approval o f the U.S. Govern ment
is app licable to it, it i s illegal and stric tly forbidd en to exp ort, intend to export, tr ansfer in any other manner whatsoever, sel l any
hardwar e or technical da ta, provide any a ssociated ser vice to any
non-U. S. r esident, beyond or within the United States territory,
until th e valid lice nse or writ ten approval has been i ssued by the
Depar tments of th e U.S. Gover nment h aving j urisdiction . Addi tionall y U.S. law prohibits the sale, transfer, o r export of items to
certai n restri cted parties, des tinations, and embar goed countries,
as iden tied on lis ts maintaine d by the U.S . Departm ent of State,
the U.S. Department of Commerce, and t he U.S. Depar tment of
Treasury. It i s the responsib ility of the Customer to be aw are of
these lis ts. The sale, tran sfer, transport ation, or shipme nt outside of the U.S. of any product prohibited o r restricte d for expor t
without complying with U. S. export c ontrol laws and re gulations,
includin g prope r expor t licen sing, do cumentation or au thorization, is unlaw ful and may result in civil and/or cr iminal pen alties
and/or constitute a fe deral cri me. Diver sion cont rary to U.S. law
is stric tly prohibited .
Page 2
2
SAFETY SUMMARY
Before operating this product, carefully read and study this Operation and Maintenance Manual.
The PVS-14/6015 is a precision electro-optical instrument, and requires careful handling. To avoid damage to the equipment or physical harm to the user when operating the PVS-14/6015, follow all WARNINGS, CAUTIONS and NOTES.
Below you will nd denitions of the following alerts that appear throughout this Manual:
WARN ING — Identies a clear danger to the person operating the equipment.
CAUTION – Identies risk of damage to the equipment.
NOTE – Serves to highlight essential procedures, conditions, and statements, or convey important in-
structional data to the user.
WARNING:
This product contains natural rubber latex which may cause allergic reactions! The FDA
has reported an increase in the number of deaths that are associated with an apparent sensitivity to natural latex proteins. If you are allergic to latex, it is a good idea to learn which products
contain it and strictly avoid exposure to those products.
WARNINGS:
Toxic Material
The image intensier’s phosphor screen contains toxic materials.
• If the image intensier breaks, be extremely careful to avoid inhaling the phosphor screen
material. Do not allow the material to come in contact with the mouth or open wounds on the
skin.
• If the phosphor screen material comes in contact with your skin, wash it o immediately with
soap and water.
• If you inhale/ swallow any phosphor screen material, drink a lot of water, induce vomiting, and
seek medical attention as soon as possible.
WARNINGS:
• The monocular will not turn o automatically when ipped up. The monocular needs to be
turned o with the power switch.
• The compass illuminator is visible to other people using night vision devices.
• Do not use contaminated eyecups or eyeguards. If contaminated, they must be replaced.
• When installing the headmount over the protective mask, be careful not to break the protec-
tive mask’s seal around your face.
The information provided in this manual is for familiarization purposes only; the contents may undergo further
changes with no commitment by Armasight© to notify customers of any updates.
Armasight© assumes no responsibility for any misprints or other errors that this manual may contain.
©2012 by Armasight. Al l rights reserved.
Page 3
3
CAUTION:
• The PVS-14/6015 is a precision optical instrument and must be handled carefully at all times
to prevent damage.
• To prevent damage, be especially careful when leaving the helmet mount in the ipped up
position or removing the helmet mount from the helmet.
• Do not scratch the external lens surfaces or touch them with your ngers.
• Do not wipe the demisting shield with lens paper while it is damp, or using wet lens paper, as
this can damage the coating.
• To protect the image intensier, keep the lens cap securely tted over the objective lens when
the monocular is not in use or when it is being operated in daylight conditions.
• Light from the IR illuminator is invisible to the unaided eye. However, it can be detected by
other night vision devices.
• If you use the rubber eyecups for a long period of time, you may suer skin inammation. If
you develop any symptoms, consult a doctor immediately.
NOTES:
To avoid physical injury and damage to the equipment, carefully read and understand the following safet y precautions.
• The equipment requires some ambient light (moonlight, starlight, etc.) to operate.
• Performance of the device in nighttime conditions depends on the level of ambient light in
the environment. Please remember the following:
— The level of ambient light is reduced by the presence of clouds, shade, or objects that block
natural light (trees, buildings, etc.).
— The equipment is less eective when operated in shadows and other darkened areas.
— The equipment is less eective when operated in rain, fog, sleet, snow, dust or smoke.
— The equipment will not “see” through dense smoke.
• At operating temperatures below -20°C (-4°F), the use of an alkaline battery is not recommended, as the battery life will be severely reduced. Under said conditions, lithium-iron disulde 1.5V AA batteries or their equivalent should be used.
• The IR illuminator is intended for increased illumination, as needed, when viewing at a close
distance of up to 3m.
• For the purpose of returning defective components, retain all packaging materials.
Page 4
4
LIST OF CONTENTS
TITLE PAGE
Safety Summary 2
List of Contents 4
List of Figures 5
How to Use This Manual 6
1. INTRODUCTION 7
1.1 General Information 7
1.1.1 Type of Manual 7
1.1.2 Model Number and Equipment Name 7
1.1.3 Purpose of Equipment 7
1.1.4 Reporting Equipment Improvement Recommendations 7
1.2 Warranty Information and Registration 8
1.2.1 Warranty Information 8
1.2.2 Limitation of Liability 8
1.2.3 Product Warranty Registration 8
1.2.4 Obtaining Warranty Service 9
1.3 Cross References 9
1.4 List of Abbreviations 10
1.5 Glossary 11
2. DESCRIPTION AND DATA 12
2.2 Equipment Description 12
2.2.1 Equipment Characteristics, Capabilities, and Features 12
2.2.2 Location and Description of Major Components 12
2.2.3 Equipment Data 15
2.3 Principles of Operation 16
2.3.1 Mechanical Functions 16
2.3.2 Optical Functions 16
2.3.3 Electronic Circuit Function 17
3. OPERATING INSTRUCTIONS 18
3.1 Description and Use of Operator’s controls and indicators 18
3.1.1 Operator Controls and Indicators 18
3.2 Preventive Maintenance Checks and Service s (PMCS) 20
3.2.1 Preventive Maintenance Checks and Services 20
3.2.2 Resolution Check Using the TS- 4348/UV Test Set 24
3.2.3 Inspection Criteria for Proper Image Intensier Operation 26
3.3 Assembly and Preparation for Use 29
3.3.1 Unpacking 29
3.3.2 Installation of the Battery 29
3.3.3 Installation of the Eyecup Or Eyeguard 30
3.3.4 Installation of the Demist Shield 30
3.3.5 Installation of the Sacricial Window 31
3.3.6 Installation and Adjustment of the Headmount 31
3.3.7 Installation of the Headmount/Helmet Mount Adapter 32
3.3.8 Installation of the Helmet Mount to a Helmet 32
3.3.9 Installation of the Headmount with a Protective Mask 33
Page 5
5
3.3.10 Installation of the Weapon Mount 34
3.3.11 Installation of the Compass Caution 35
3.3.12 Installation of the 3x Magnier 36
3.3.13 Mounting MUNVM to a Weapon with a Quick-Release Picatinny Mount Adapter 36
3.3.14 Mounting a MUNVM to a Weapon with the AIM Advanced Integrated Mount 37
3.4 Operating Procedures 38
3.4.1 Hand-Held Operation 38
3.4.2 Head-Mounted Operation 38
3.4.3 Helmet-Mounted Operation 39
3.4.4 Weapon-Mounted Operation 41
3.4.5 IR Source Operations 42
3.4.6 Operation with a Compass 42
3.4.7 Operation with a 3x Magnier 43
3.4.8 Operation with a Gain Control 43
3.4.9 Preparation for Storage 44
3.5 Operation under Unusual Condition 44
3.5.1 Operation in Dusty or Sandy Areas 44
3.5.2 Operation in Rainy or Humid Conditions 45
3.5.3 Operation in Salt Water Areas 45
3.5.4 Operation in Nuclear, Biological and Chemical (NBC) Environments 45
4. MAINTENANCE PROCEDURES AND TROUBLESHOOTING 46
4.1 Lubrication Instructions 46
4.2 Troubleshooting Procedures 46
4.2.1. Troubleshooting 45
4.3. Operator’s Maintenance Procedures 47
4.3.1 Cleaning the MUNVM 47
4.3.2 Headmount Maintenance 48
4.3.3 Neck Cord Maintenance 49
4.4 Service/Packing and Unpacking 49
4.4.1 Return Instructions 49
APPENDIX 50
A. Components of End Item (COEI) and Basic Issue Items (BII) Lists 50
B. Additional Authorization List (AAL) 52
C. Expendable and Durable Items List 53
D. Product Warranty Registration Card 54
Alphabetical Index 55
LIST OF FIGURES
FIGURE TITLE PAGE
2-1. Components of NVMPS 13
2-2. 3X Magnier and Compass for PVS-14/6015 13
2-3. Shipping and storage cases for PVS-14/6015 14
2-4. Multi-Use Night Vision Monocular 14
2-5. Optional Equipment 14
2-6. Optical Function Diagram 17
Page 6
3-1. Monocular Controls and Indicators 18
3-2. TS-4348/ UV Test Set Pattern 25
3-3. Shading 26
3-4. Edge Glow 27
3-5. Bright Spots and Emission Points 27
3-6. Fixed-Pattern Noise 28
3-7. Chicken Wire 29
3-8. Battery, Eyecup and Eyeguard Installation 30
3-9. MUNVM Headmount Adjustments 31
3-10. Headmount/Helmet Mount Adapter Installation 32
3-11. Installation of Helmet Mount 33
3-12. Helmet Mount 33
3-13. Reassembly of Helmet Mount 33
3-14. Weapon Mount Usage 34
3-15. Locating the Magnet 35
3-16. Compass Installation 35
3-17. 3X Magnier Installation 36
3-18. 3X Magnier Installation with Focus Ring Adapter 36
3-19. Mounting Optional Bracket to the MUNVM 37
3-20. Clamping Device on the Mount Top 37
3-21. QRM Assembled with MUNVM 37
3-22. AIM Assembled with MUNVM 37
3-23. Headmount/Helmet Mount Adapter Operation 39
3-24. Tilt and Flip-up Assembly Mechanisms 40
3-25. View Through Installed Compass 43
3-26. Gain Control 43
4-1. Reinstalling the Neck Pad 48
4-2. Threading the Sliding Bar Buckles 48
A-1. Components of End Item 51
HOW TO USE THIS MANUAL
USAGE
You must familiarize yourself with the entire manual before operating the equipment. Before performing any kind of maintenance on your device, read the section on maintenance in its entirety. Follow all
WARNINGS, CAUTIONS, and NOTES.
MANUAL OVERVIEW
This manual contains sections on Operating and Maintaining the PVS-14/6015 Night Vision Monocular.
The Components of End Items (COEI) and Basic Issue Items (BII) Lists can be found in Appendix A.
The Additional Authorization List (AAL) can be found in Appendix B.
The Expendable and Durable Items List can be found in Appendix C.
The Product Warranty Registration Card can be found in Appendix D.
6
Page 7
7
1
INTRODUCTION
1.1 GENERAL INFORMATION
1.1.1 TYPE OF MANUAL
Operation and Maintenance.
1.1.2 MODEL NUMBER AND EQUIPMENT NAME
PVS-14 Multi-Use Night Vision Monocular.
6015 Multi-Use Night Vision Monocular.
1.1.3 PURPOSE OF EQUIPMENT
To provide the operator with the ability to observe at night under moonlight and starlight conditions.
The PVS-14/6015 can be used as a handheld, head-mounted, helmet-mounted or weapon-mounted
device to allow walking, weapon ring, short-range surveillance, map reading, vehicle maintenance,
and administration of rst aid.
1.1.4 REPORTING EQUIPMENT IMPROVEMENT RECOMMENDATIONS
User recommendations for improvements to the device are encouraged.
Mail your comments to Armasight Inc., 815 Dubuque Avenue, South San Francisco, CA 94080, USA.
Or, send an email to info@armasight.com.
Page 8
8
1.2 WARRANTY INFORMATION AND REGISTRATION
1.2.1 WARRANTY INFORMATION
This product is guaranteed to be free from manufacturing defects in material and workmanship under
normal use for a period of two (2) years from the date of purchase. In the event that a defect covered
by the below warranty occurs during the applicable period stated above, Armasight, at its discretion,
will either repair or replace the product; such action on the part of Armasight shall be the full extent of
Armasight’s liability, and the Customer’s sole and exclusive reparation. This warranty does not cover a
product if it has (a) been used in ways other than its normal and customary manner; (b) subjected to
misuse; (c) subjected to alterations, modications or repairs by the Customer of by any party other than
Armasight without prior written consent of Armasight; (d) special order or “close-out” merchandise
or merchandise sold “as-is” by either Armasight or the Armasight dealer; or (e) merchandise that has
been discontinued by the manufacturer and either parts or replacement units are not available due to
reasons beyond the control of Armasight. Armasight shall not be responsible for any defects or damage that in Armasight’s view are a result from the mishandling, abuse, misuse, improper storage or
improper operation of the device, including use in conjunction with equipment that is electrically or
mechanically incompatible with, or of inferior quality to, the product, as well as failure to maintain the
environmental conditions specied by the manufacturer. CUSTOMER IS HEREBY NOTIFIED THAT OPER-
ATION OF THE EQUIPMENT DURING DAYLIGHT HOURS OR UNDER ANY EXCESSIVE LIGHT CONDITIONS
MAY PERMANENTLY DAMAGE THE INTERNAL COMPONENTS OF THE UNIT AND SAID DAMAGE WILL
NOT BE COVERED UNDER THIS WARRANTY. This warranty is extended only to the original purchaser.
Any breach of this warranty shall be enforced unless the Customer noties Armasight at the address
noted below within the applicable warranty period.
The Customer understands and agrees that except for the foregoing warranty, no other warranties
written or oral, statutory, expressed or implied, including any implied warranty of merchantability or
tness for a particular purpose, shall apply to the product. All such implied warranties are hereby and
expressly disclaimed.
1.2.2 LIMITATION OF LIABILITY
Armasight will not be liable for any claims, actions, suits, proceedings, costs, expenses, damages or
liabilities arising out of the use of this product. Operation and use of the product are the sole responsibility of the Customer. Armasight’s sole undertaking is limited to providing the products and services
outlined herein in accordance with the terms and conditions of this Agreement. The provision of products sold and services performed by Armasight to the Customer shall not be interpreted, construed,
or regarded, either expressly or implied, as being for the benet of or creating any obligation toward
any third party of legal entity outside Armasight and the Customer; Armasight’s obligations under this
Agreement extend solely to the Customer. Armasight’s liability hereunder for damages, regardless of
the form or action, shall not exceed the fees or other charges paid to Armasight by the Customer or
Customer’s dealer. Armasight shall not, in any event, be liable for special, indirect, incidental, or consequential damages, including, but not limited to, lost income, lost revenue, or lost prot, whether such
damages were foreseeable or not at the time of purchase, and whether or not such damages arise
out of a breach of warranty, a breach of agreement, negligence, strict liability or any other theory of
liability.
1.2.3 PRODUCT WARRANTY REGISTRATION
In order to validate the warranty on your product, Armasight must receive a completed Product Warranty Registration Card for each unit, or the Customer can complete a warranty registration on our
website, at www.armasight.com. Please complete the included form (Appendix D) and immediately
mail it to our Service Center:
Armasight Inc.
815 Dubuque Avenue
South San Francisco
CA 94080
United States of America.
Page 9
9
1.2.4 OBTAINING WARRANTY SERVICE
To obtain warranty service on your unit, the End-user (Customer) must notify the Armasight service
department via email. Send any requests to service@armasight.com to receive a Return Merchandise
Authorization number (RMA). When returning any device, please take in the product to your retailer, or
send the product, postage paid and with a copy of your sales receipt, to Armasight Corporation’s service center at the address listed above. All merchandise must be fully insured with the correct postage;
Armasight will not be responsible for improper postage or merchandise that becomes lost or damaged
during shipment. When sending product back, please clearly write the RMA# on the outside of the
shipping box. Please include a letter that indicates your RMA#, the Customer’s Name, a Return Address,
reason for the return, Contact information (valid telephone numbers and/or an e-mail address), and
proof of purchase that will help us to establish the valid start date of the warranty. Product merchandise returns that do not have an RMA# listed may be refused, or a signicant delay in processing may
occur. Estimated Warranty service time is 10-20 business days. The End-user/ Customer is responsible
for postage to Armasight for warranty service. Armasight will cover return postage/ shipping after warranty repair to the End-user/ Customer only if the product is covered by the aforementioned warranty.
Armasight will return the product af ter warranty service by domestic UPS Ground service and/ or domestic mail. Should any other requested, required or international shipping methods be necessary, the
postage/ shipping fee will be the responsibility of the End-user/ Customer.
1.3 CROSS REFERENCES
COMMON NAME OFFICIAL NAME
Allen Wrench Socket Head Screw Key
Battery Compartment Battery Box Cover
Shipping Case Textile Bag
Cotton Swab Disposable Applicator
Neoprene Jack Plug Plug Assembly
O-Ring Gasket
Safety Screw Electrical Dial-Knob Lock
Pattern Generator Optical Instrument Reticle
Lens Covers Exit Port Covers
Paddle Switch Remote Cable Switch
Batteries AA
Technical Manual Operator and Field Maintenance Manual
Tape Fastener Loop Fastener, Loop Tape
Tape Fastener Hook Fastener, Hook Tape
Page 10
10
1.4 LIST OF ABBREVIATIONS
AAL Additional Authorization List
BII Basic Issue Items
CAGEC Commercial and Government Entity Code
cm Centimeters
COEI Components of End Item
CPC Corrosion Prevention and ControlCTA Common Table of AllowancesDA Department of the Army
EIC End Item Code
EIR Equipment Improvement Recommendation
FM Field Manual
Hrs Hours
IR Infrared
JTA Joint Table of Allowances
lbs Pounds
LED Light Emitting Diode
MUNVM Multi-Use Night Vision Monocular
NVMPS Night Vision Multi-Purpose System
MTOE Modied Table of Organization and EquipmentN/A Not Applicable
NBC Nuclear, Biological, and Chemical
NSN National Stock Number
Pam Pamphlet
PASGT Personal Armor System Ground Troops
PMCS Preventive Maintenance Checks and Services
Qty Quantity
Recm Recommended
Rqr Required
SF Standard Form
TDA Table of Distribution and AllowancesTM Technical Manual
TOE Table of Organization and EquipmentU/M Unit of Measure
Vdc Volts, direct current
Page 11
11
1.5 GLOSSARY
BLACK SPOTS. Cosmetic blemishes in the image intensier of the MUNVM, or dirt or debris between
the lenses.
BRIGHT SPOTS. Defects that can appear in the image area of the MUNVM. This condition is caused by
a aw in the lm on the microchannel plate. A bright spot is a small, non-uniform, bright area that may
icker or appear constant. Bright spots are cosmetic blemishes that are signal-induced, and usually
disappear when all light is blocked out.
BROWPADS. Three hook-and-pile browpads are provided to adjust the headmount to t dierent
head sizes. The thin browpad (for larger heads) comes attached to the headmount and the thick, or
medium (for smaller heads) browpads are stored in the carrying case.
CHICKEN WIRE. An irregular pattern of dark thin lines in the eld-of-view either throughout the image
area or in parts of the image area. In the worst cases of Chicken Wire, these lines will form hexagonal or
square, wave-shaped lines.
DARK (OR DARK AREA). A place in which there is very little light. It does not mean total darkness.
Generally, this means conditions similar to a quarter-moon or starlit night.
DARK-ADAPTED. When the user’s eyes have adjusted to the monocular’s output under low light conditions.
DIOPTER. A unit of measure used to dene eye correction. Adjustments to the diopter adjustment will
provide a clearer image for each eye.
EDGE GLOW. A defect in the image area of the monocular. Edge glow is a bright area (sometimes sparkling) in the outer portion of the viewing area.
EMISSION POINT. A steady or uctuating pinpoint of bright light in the image area and does not go
away when all light is blocked from the objective lens of the monocular. The position of an emission
point within the image area of the monocular does not move. An emission point should not be confused with a point light source in the distance.
FIXED-PATTERN NOISE. A cosmetic blemish in the image area characterized by a faint, hexagonal
(honeycomb) pattern throughout the viewing area. It most often occurs in excessive light conditions or
when viewing very bright lights. Fixed-pattern noise is inherent in the structure of the ber optics and
can be seen in every image intensier if the level of light is high enough.
FLASHING. A defect in the image area of the monocular. The image appears to icker or ash.
FLICKERING. See “ashing.”
GAIN. The number of times a night vision device amplies light input.
IMAGE INTENSIFIER. An electro-optical device that detects and amplies ambient light to produce a
visual image.
INFINITY FOCUS. Adjustment of the objective lens so that a distant object, such as a star or the point
light on a distant tower, forms the sharpest image.
INTERMITTENT OPERATION. A defect in the image area of the monocular. See “ashing.”
IR SOURCE. IR Light Emitting Diode (LED). When turned on, the IR source provides additional illumina-
tion to enhance existing light conditions, and should be used only for performing nearby tasks.
MICROCHANNEL PLATE. A current-multiplying optical disk that intensies the electron image produced by the photocathode.
PHOTOCATHODE. The input optic of an image intensier that absorbs light energy and releases electrical energy in the form of an electron image.
SCINTILLATION. A faint, random, sparkling eect throughout the image area. Scintillation is a normal
characteristic of the image intensier and should not be confused with emission points. Scintillation is
more pronounced under low light conditions. Also called “video noise.”
SHADING. The viewed image should be a full circle. If shading is present, you will not see a fully circular
image. Shading is indicative of a dying photocathode and is caused by a defective vacuum seal of the
image intensier. Shading is very dark and you cannot see an image through it.
Page 12
12
2
DESCRIPTION AND DATA
2.1 EQUIPMENT DESCRIPTION
2.2.1. EQUIPMENT CHARACTERISTICS, CAPABILITIES, AND FEATURES
The PVS-14/6015 is a hand-held, head-mounted, helmet mounted, or weapon-mounted night vision
system that enables walking, weapon ring, short-range surveillance, map reading, vehicle maintenance, and administration of rst aid in both moonlight and starlight conditions. Each unit allows for
vertical adjustment (by using the head strap), fore-and-af t adjustment, objective lens focus and eyepiece focus. The monocular is also equipped with an IR source and a low battery indicator. The PVS-14
model is equipped with a manual gain control.
2.2.2. LOCATION AND DESCRIPTION OF MAJOR COMPONENTS
The NVMPS includes the items shown in Figures 1-1, 1-2, 1-3. The major components are the headmount, helmet mount, monocular, carrying case, and the shipping and storage case.
a. Monocular
The monocular (see Figure 2-4) consists of various components such as an objective lens, an image
intensier (not shown), an eyepiece lens and a battery cap.
The monocular also uses the accessories listed below:
Demist Shield – The demist shield (Figure 2-1) is used to prevent the eyepiece lenses from becoming fogged.
Sacricial Window – A replaceable sacricial window (Figure 2-1) is supplied to protect the objective lens during operation in adverse conditions.
Compass – The compass (Figure 2-2) enables the operator to see azimuth readings in the monocular.
Tethering Cord – The tethering cord (Figure 2-1) enables the user to attach the compass or 3X magnier to a button hole or belt loop to guard against dropping or losing these items.
3X Magnier – (Additional Authorized Item) The 3Xmagnier (Figure 2-2) is a lens assembly which
can be added to the monocular to extend the operator’s obser vation ranges.
b. Headmount
The headmount (Figure 2-1) secures the monocular to the operator’s head for night viewing and provides freehand support for use with a weapon, protective mask, or for other purposes in which freehand operation is required. It is adjustable and cushioned. The thin browpad should be used for larger
heads, and comes attached to the headmount; the thick and medium browpads should be used for
smaller heads, and are stored in the carrying case.
Page 13
HEAD/HE LMET MOUNT
ADAPTER
TETHE RING
CORD
THIN BRO WPAD
HEADMOUNT
WEAPON M OUNT
BATTERY CAR -
TRIDGE
NECK CORD
OBJEC TIVE
LENS CAP
HELME T MOUNT
CARRYI NG CASE
DEMIST
EYEGUA RD
SHIELD
SACRIFICIAL
WINDOW
BAT TER Y
MONOCULAR
Figure 2-1. Components of NVMPS
COMPASS
MEDIUM A ND
THICK BR OWPADS
OPERATOR ’S
MANUAL
LENS PAPER
CARRYI NG CASE
STRAP
3X MAGNIFIE R
(ADDIT IONAL ITEM)
Figure 2-2. 3X Magnier and Compass for PVS-14/6015
13
Page 14
14
(SEE FIGUR E 2-1. FOR DETAIL S)
SHIPPING
AND
STORAG E
CASE
Figure 2-3. Shipping and storage cases for PVS-14/6015
EYEPIECE
LENS
OBJECTIVE
LENS
POWER
SWITCH
AIM
BAT TER Y
CAP
Figure 2-4. Multi-Use Night Vision Monocular
BRACK ET
AIM PVS14 KIT
(ANKI000046)
DOUBLE L EVER-LOCK QU ICK RELEASE
PICATINNY M OUNT ADAPTER #26
(ANAM000004)
Figure 2-5. Optional Equipment
GAIN
CONTROL
BRACKE T PVS14 #62
(ANKI000046)
Page 15
15
c. Helmet Mount
The helmet mount (Figure 2-1) secures the monocular to the Personal Armor System Ground Troops
(PASGT) helmet, allowing freehand support for use with a weapon, protective mask and/ or other purposes in which freehand operation is required. The new helmet mount is made of a ruggedized metal,
unlike the older version, which is made of plastic.
d. Headmount/Helmet Mount Adapter
The headmount/ helmet mount adapter (Figure 2-1) is attached to the monocular to allow use with the
headmount or helmet mount. It allows mounting in front of the left or right eye.
e. Weapon Mount
The weapon mount (Figure 2-1) adapts the monocular to the receiver rail as congured for the modular
weapon system kit.
f. Carrying Case
The carrying case (Figure 2-3) is provided for transportation and protection of the monocular, headmount, battery and accessories. Two slide keepers are provided for belt attachment; three D-rings are
provided for shoulder and leg strap attachment. A carrying case strap is also provided, and can be attached to the two D-rings on the back of the carrying case.
g. Shipping and Storage Case
The NVMPS is supplied in a shipping and storage case (Figure 2-3).
h. AIM PVS14 Kit
AIM Advanced Integrated Mount (Figure 2-5) allows the user to quickly convert the PVS-14 into a weapon sight. The Kit includes the AIM and bracket for installing PVS-14 onto the AIM.
i. Double Lever-Lock Quick Release Picatinny Mount Adapter #26
Small arms adapter that allows the PVS-14 to be mounted on a weapon using Picatinny Mil 1913 rail
(Figure 2-5).
j. Bracket PVS14 #62
Allows the PVS-14 to be mounted on the Quick Release Picatinny Mount Adapter (Figure 2-5).
2.2.3. EQUIPMENT DATA
The following tables provide information pertaining to the operational, electrical, mechanical, optical,
and environmental characteristics of the monocular.
TABLE 21. OPERATOR ADJUSTMENT LIMITS
ITEM LIMITS
Diopter Focus +2 to -6 diopters
Objective Focus 25cm (9.8”) to innity
TABLE 22. ELECTRICAL DATA
ITEM DATA
Power Source Battery (1.5 Vdc max ea.)
Battery Requirements 1 AA Alkaline or 1 AA 1.5 Vdc Lithium L91
Page 16
16
TABLE 23. MECHANICAL DATA
ITEM CHARACTERISTICS
Shipping and Storage Case Size: Approx. 356 x 241 x 203 mm (14” x 9.5” x 8”)
Weight: 1.09kg (2.4 lbs.)
Carrying Case Size: Approx. 352 x 240 x 200 mm (14” x 9.5” x 8”)
Monocular (see Note) Weight: 0.39kg (14 ounces)
NOTE:
The weight of the monocular does not include accessories.
TABLE 24. OPTICAL DATA
ITEM DATA
Magnication 1.0X (3X with 3X magnier)
Field-of-View 40° (13° with 3X magnier)
Diopter Focus +2 to -6 diopters
Objective Focus 25cm (9.8”) to innity
TABLE 25. ENVIRONMENTAL DATA
ITEM DATA
Monocular Operating Temperature -51°C to +49°C
Monocular Storage Temperature -51°C to +85°C
Illumination Required Overcast starlight to moonlight
2.3 PRINCIPLES OF OPERATION
2.3.1. MECHANICAL FUNCTIONS
The mechanical functions used to operate the NVMPS adjust to accommodate physical dierences of
individual operators. These functions include the power switch, eye relief adjustment, diopter adjustment, gain control, and objective focus. The mechanical controls are identied in Figure 2-4.
NOTE:
The gain control function is not available with the 6015 or PVS-14NG model.
2.3.2 OPTICAL FUNCTIONS
The optical functions include an objective lens, image intensier, and eyepiece lens (Figure 2- 6). The
objective lens collects light reected from the environment. The image is inverted and focused on the
image intensier. The image intensier converts the captured light into a visible image, re-inverting it
so that it can be viewed through the eyepiece lens.
Page 17
17
PHOTOCATHODE
MICROC HANNEL
PL ATE
FIBER- OPTIC
INVERTER
OBJEC TIVE
LENS
PHOSPHO R
SCREEN
IMAGE
INTENSIFIER
POWER
SUPPLY
EYEPIE CE
LENS
EYE
Figure 2-6. Optical Function Diagram
2.3.3. ELECTRONIC CIRCUIT FUNCTION
The electronic circuit regulates the direct current voltage from the battery to the image intensier and
IR source as required. It also monitors the output voltage of the battery and turns on a low-battery
indicator when the available battery voltage is 1.9 – 2.1 Vdc.
a. Power Source
The electronic circuit is powered by one battery.
b. High Light Cut-O
The monocular will automatically turn o after 70 ±30 seconds of operation in daylight or other brightly lit environments. Individual bright lights (headlights, ashlights, or other concentrated light sources)
will not actuate the high light detector located on the front of the monocular. To turn the monocular
back ON, turn the power switch to RESET/ OFF, and then to ON again.
Page 18
18
3
OPERATING INSTRUCTIONS
3.1 DESCRIPTION AND USE OF OPERATOR’S
CONTROLS AND INDICATORS
NOTE:
The MUNVM is a precision electro-optical instrument, and must be handled carefully. If the
equipment fails to operate, refer to the Troubleshooting Procedures in Chapter 4.
3.1.1. OPERATOR CONTROLS AND INDICATORS
The MUNVM is designed to adjust for dierent users and corrects for most dierences in eyesight. The
controls and indicators for the MUNVM are shown in Figure 3-1, and are described in Table 3-1.
LAT CH
OBJECTIVE
FOCUS
BATTERY POL ARITY
INDIC ATORS (HI DDEN)
DIOPTER
ADJUSTMENT
IR LENS
POWER
SWITCH
GAIN
CONTROL
HIGH LIG HT CUT-OFF WINDO W
Figure 3-1. Monocular Controls and Indicators
EYE RELI EF
ADJUSTMENT
Page 19
NOTE:
The gain control function is not available with the 6015 model.
NOTE:
Indicators showing that the battery is low and that the IR is active are both visible in the eyepiece lens.
TABLE 31. MONOCULAR CONTROLS AND INDICATORS
CONTROLS AND INDICATORS FUNCTIONS
Controls the monocular and IR source, ON or OFF.
Same as system OFF. Also resets monocular after high light
cut- o.
Turn the knob clockwise to momentarily activate the IR source.
For continuous operation of the IR, pull and turn the knob
clockwise from the ON position.
Power Switch
RESET/ OFF
ON Monocular activated.
IR/ PULL
CAUTION
Do not use excessive force when operating the power switch.
Low Battery Indicator
IR Source On Indicator
Gain Control
(PVS-14 only)
Objective Focus Focuses objective lens. Adjusts for sharpest image of viewed object.
Diopter Adjustment
Eye Relief Adjustment Adjusts the distance between your eye and the monocular.
Latch
Battery Polarity Indicators
:
The low battery indicator will blink on and o when there are less than 30
minutes of battery life remaining. It is visible through the eyepiece, just outside the intensied eld-of-view.
The IR Source On indicator will blink when the IR is activated. It is visible
through the eyepiece just outside the intensied eld-of-view.
Adjusts the system gain from a minimum value of approximately 25 to a
maximum value greater than 3,000.
Focuses eyepiece lens for use without a need for glasses. Adjusts for sharpest
image of intensier screen.
Latch used for separation of monocular from head-mount/ helmet mount
adapt er.
This feature, molded into the battery housing, shows the proper orientation
of the batter y. Some versions have a bubble molded into the top of the battery house that indicates polarity.
19
Page 20
20
3.2 PREVENTIVE MAINTENANCE CHECKS AND
SERVICES PMCS
3.2.1. PREVENTIVE MAINTENANCE CHECKS AND SERVICES
a. General
To verify that the MUNVM is mission-ready, perform the preventive maintenance procedures in accordance with Table 2.2 prior to each mission. Preventive maintenance procedures include inspection,
cleaning, and performance of the checkout procedures.
b. Warnings and Cautions
Always observe the WARNINGS and CAUTIONS appearing in the table. Warnings and cautions appear
before any applicable procedures. You must observe the warnings and cautions to prevent serious
injury to yourself and others, and to prevent damage to the equipment.
c. Explanation of Table Entries
(1) Item Number Column. Numbers in this column are for reference. When completing the Equipment
Inspection and Maintenance Worksheet, include the item number for the check/ service indicating a
defect. Item numbers also appear in the order in which checks and services should be performed.
(2) Interval Column. This column tells you when you must do the procedure in the Procedure Column.
BEFORE procedures must be done before you operate or use the equipment for its intended mission.
DURING procedures must be done during the time you are operating or using the equipment for its
intended mission. AFTER procedures must be done immediately after you have operated or used the
equipment.
(3) Location, Check/ Service Column. This column provides the location and the item to be checked
or serviced. The item location is underlined.
(4) Procedure Column. This column describes the procedure you must do to check or service the item
listed in the Check/ Service column, in order to determine if the equipment is ready for operation. You
must do the procedure at the time stated in the interval column.
(5) Not Fully Mission Capable If… Column. Information in this column tells you which defects prevent the equipment from being mission-capable. If you perform check and service procedures that
indicate defects listed in this column, do not operate the equipment. Follow standard operating procedures for maintaining the equipment or reporting equipment failure.
NOTE:
Damaged accessory items (sacricial window, demist shield, compass) do not cause the fully
assembled equipment to be “not fully mission capable.” However, the damaged component
should be replaced as soon as possible to restore full capability to the system.
d. Other Table Entries
Be sure to observe all special information and notes that appear in any tables.
Page 21
21
TABLE 31. PREVENTIVE MAINTENANCE PROCEDURES
ITEM
INTERVAL CHECK/SERVICE PROCEDURE NOT FULLY MISSI ON CAPABLE IF...
NO.
1 Before Open carrying case and inventory the
items.
MONOCULAR
2 Before/
After
Optical
Surfaces
Inspect all lenses (objective, eyepiece,
IR lens and high light cut-o window)
for dirt, ngerprint residue, chips, or
Chips or heavy scratches that
hinder vision with monocular
turned ON; cracks are present.
cracks. If necessary, clean and dry
lenses with water and lens tissue.
3 Before/
After
Battery Cap
Housing
Inspect external sur faces for cracks
or damage. Scratches, cracks, and
gouges are OK if operation is not
Cracks or damage in the bat-
tery housing.
aected.
Inspect battery compartment.
Verify that the battery cap is present.
Remove battery cap and inspect for
moisture, cracks, and corroded or
defective spring contacts. Verify that
Cap is missing, contacts dam-
aged or corroded, o-ring is
missing.
the o-ring present in the cap.
Remove battery and turn the power
switch from RESET/ OFF to ON to IR/
PULL. Each position should have a
denite stopping point. Inspect for
Power switch has no denite
stopping points; knob is bro-
ken or missing.
broken or missing knob.
Install battery per paragraph 2.6 and
check IR source functions (as well as
momentary IR source, if so equipped)
by following the operating instruc-
IR source does not work.
tions in paragraph 3.22.
Check the high light cut-o with
daylight or bright room light (not uo-
If damaged, please contact
Customer Support.
rescent light) by placing the lens cap
on the objective lens. Turn monocular
ON and observe that the system cuts
OFF within 70 ±30 seconds.
Turn the device OFF and then ON to
reenergize it.
NOTE:
If the monocular fails this highlight
cut-o test, it does not cause the
end item to be nonmission capable.
However, it should be sent to higher level of maintenance as soon as
possible.
Check gain control for free movement
and operation per paragraph 3.2.5.
Knob does not move freely, or
does not vary the gain.
Page 22
22
TABLE 31. CONTINU ED
ITEM
INTERVAL CHECK/SERVICE PROCEDURE NOT FULLY MISSI ON CAPABLE IF...
NO.
4 Before/
After
Monocular Inspect for cracks or damage. Scratch-
es, cracks, chips and gouges are OK if
Cracks or damage in the
monocular.
operation is not aected.
5 Before/
After
Eyepiece Lens Rotate diopter adjustment to make
sure the eyepiece lens moves freely
Binding does not move freely
or is too loose.
and is not loose. Range is approximately ½ turn.
6 Before/
After
7 Before/
After
Eyecup Inspect for dirt, dust, cracked or torn
eyecup. Inspect for bent, broken, or
improperly tting eyepiece lens. If
necessary, clean with water.
Eyeguard Inspect for dirt, dust, cracked or torn
eyeguard. Inspect for bent, broken, or
improperly tting eyeguard. If necessary, clean with water.
Chips and cracks are permitted
on the eyecup retaining rings
as long as they do not interfere
with installation of eyecup.
Chips and cracks are permit-
ted on the eyeguard retaining
rings as long as they do not
interfere with installation of
the eyeguard.
8 Before/
After
Objective
Lens
Rotate focus ring to ensure free movement (range is approximately 1/3
turn). Check objective lens for chips,
Focus ring is binding or stuck.
cracks and dents.
Check the innity focus locking ring
for tightness. Check for cracks.
Chips, cracks, or dents prevent
full eld-of-view or the ability
to focus.
Cracked or loose.
9 Before/
After
Neck Cord
and Objective
Lens Cap
Inspect for cracked, torn, or missing
objective lens cap. Inspect neck cord
for cut, damaged, or loose ends.
Damaged.
Re-tie ends if necessary.
10 Before/
After
Viewed Image
NOTE:
Operator may use the TS-4348/
UV to check resolution (paragraph
3.2.2).
11 Before/
After
HEADMOUNT
Straps/Pads
Refer to paragraph 2.2.3 to inspect for
operational defects.
NOTE:
Flickering, ashing, edge glow,
or shading is observed.
If any of the following items are
damaged it does not cause the entire end item to be “not fully mission
capable”. However, the damaged
item should be replaced as soon as
practical to restore full capability of
the system.
Inspect for cuts, tears, fraying, holes,
cracks, or defective fasteners.
Damage causes straps or pads
to be unusable.
Page 23
23
TABLE 31. CONTINU ED
ITEM
INTERVAL CHECK/SERVICE PROCEDURE NOT FULLY MISSI ON CAPABLE IF...
NO.
12 Before/
After
Socket Inspect for dirt, dust, or corrosion.
Insert monocular latch into socket to
Damaged, latch won’t lock or
is too loose.
verify secure attachment of monocular to headmount. If necessary, clean
socket with water.
13 Before
/Af ter
Eye Relief
Adjustment
Press the eye relief adjustment and
check for free motion. Inspect for
Binding, damaged or non-
operational slide mechanism.
damage.
14 Before
/Af ter
15 Before
/Af ter
16 Before
/Af ter
17 Before
/Af ter
18 Before
/Af ter
19 Before/
After
20 Before
/Af ter
HELMET MOUNT
Straps
Inspect for cuts, tears, fraying, holes,
cracks, or defective fasteners.
Socket Inspect for dirt, dust, or corrosion.
Insert monocular latch into socket to
verify secure attachment of monocular to helmet mount. If necessary,
clean socket with water.
Fore-and-Aft
Adjustment
Press the two side buttons on plastic
mount or depress side lever on metal
mount and check for free motion.
Inspect for damage.
MOUNTING ADAPTERS
Headmount/
Helmet
Mount
Adapter
Inspect for dirt, dust or corrosion.
Insert into headmount or helmet
mount socket to verify secure attachment.
Weapon
Mount Inspect for dust, dirt or corrosion.
ACCESSORIES
CAUTION:
IThe coating on the demist shield
can be damaged if cleaned while
wet or if cleaned with wet lens paper. Clean only when the demist
shield is dry and only with dry pape r.
Inspect for dirt, dust, scratches or
damage. If necessary, clean when
shield is dry (use dry lens tissue only).
Sacricial
Window
Inspect for dirt, dust, scratches or
damage. If necessary, clean per paragraph 4.2.
Damage causes straps to be
unserviceable.
Damaged, latch won’t lock or
is too loose.
Binding, damaged or non-
operational slide mechanism.
Damaged, will not latch
securely.
Damaged, will not mount to
monocular or will not mount
to rail.
Damage or scratches hinder
vision when the monocular is
turned on.
Damage or scratches hinder
vision when the monocular is
turned on.
Page 24
24
TABLE 31. CONTINU ED
ITEM
INTERVAL CHECK/SERVICE PROCEDURE NOT FULLY MISSI ON CAPABLE IF...
NO.
21 Before
/Af ter
Compass Inspect for dirt, dust, scratches, or
damage. If necessary, clean with water
Damaged; compass is not
visible.
and dry with lens tissue.
Install compass and turn on monocular. When the illumination button is
depressed, compass should be visible.
22 Before
/Af ter
3X Magnier
(Additional
Inspect optical surface for dirt, dust,
scratches or cracks.
Damage; scratches hinder
vision.
Authorized
Item)
CARRYING CASE
23 Before
/Af ter
Case
Remove all items and shake out loose
dirt or foreign material. Inspect for
tears, cuts, excess wear, or damage to
mounting clips.
24 Before
/After
Shoulder
Strap
Inspect for cuts, tears, or excess wear
or damaged clips.
3.2.2. RESOLUTION CHECK USING THE TS4348/ UV TEST SET
NOTE:
The TS-4348/ UV Test Set can be used by the operator to check the resolution of a monocular
at any time.
NOTE:
The TS-4348/ UV Test Set can be used by Direct Support/Intermediate Level to perform the resolution testing 180 Day Service. If a system fails it must be tested on the TS-3895A/UV Test Set.
NOTE:
Verify the resolution of the monocular using the TS-4348/ UV Test Set at every opportunity. The
resolution cannot be accurately measured without the test set.
The following procedures are designed to check the performance of the image intensier.
a. Setup
Before using the TS-4348/ UV Test Set, familiarize yourself with its operation and specic warnings and
cautions.
Page 25
25
NOTE:
• The resolution test must be performed in a darkened area. Your eyes must be dark-adapted to
perform this test. Review the following test procedure before entering the dark area:
- When viewing through the TS-4348/ UV Test Set on the “high light” level, expect cosmetic
blemishes, such as chicken wire, black spots, and xed-pattern noise, to stand out. This is
acceptable.
- Returns of the MUNVM for cosmetic defects must be based on an outdoor evaluation, not
the TS-4348/ UV Test Set.
b. Low Light and High Light Resolution Test Procedure
Test the monocular for low light and high light resolution performance by performing the following
steps.
(1) Set the HIGH/ LOW switch on the test set to LOW.
(2) Turn o the room light and let your eyes adjust to the dark.
(3) Turn on the test set by setting the “II/ OFF/ III” switch to “III.”
(4) Turn on the monocular and insert it into the test port on the test set.
(5) Look through the monocular and view the projected pattern (see Figure 3-2). If necessary, focus the
eyepiece lens and then the objective lens to obtain the sharpest image.
(6) To pass the test, the MUNVM monocular must be able to resolve Group 2, Element 2, under low light
conditions. If the MUNVM does not pass the test, please contact Customer Support, as you will need
to return the device for repair. The operator must document resolution failures on the maintenance
record.
1
GROUP NU MBER
5
ELEMEN T NUMBERS
READ TH IS FOR LOW
LIGHT RE SOLUTION
FOR MUNVM
NOTE
THE TARGET SH OWN IS FOR EXAMPLE ON LY AND IS NOT DR AWN
TO SCALE .
Figure 3-2. TS-4348/UV Test Set Pattern
2
2
3
4
5
6
4
2
3
4
5
6
1
3
1
2
3
5
1
2
4
3
4
5
6
5
4
1
6
2
1
READ TH IS FOR
HIGH LIG HT
6
RESOLUT ION
FOR MUNVM
NOTE:
For a pattern to be resolvable, three vertical bars and three horizontal bars must be visible.
(7) Flip the HIGH/ LOW switch to HIGH.
(8) Look through the monocular and view the projected pattern (see Figure 3-2). If necessary, refocus
the objective lens and then the eyepiece lens to obtain the sharpest image.
Page 26
26
(9) To pass the test, the MUNVM must be able to resolve Group 3, Element 5, under high light conditions. If the monocular does not pass the test, please contact Customer Support, as you will need to
return the device for repair.
NOTE:
When using the TS-4348/ UV Test Set, you are not viewing the entire image intensier. Therefore, operational and cosmetic inspections must be done without the test set as specied in
paragraph 3.2.3.
(10) Check for ashing, ickering, and other unstable behavior or operational defects (paragraph 3.2.3)
in the image intensier. To view the image intensier under low light conditions, ip the HIGH/ LOW
switch to LOW and allow your eyes to become accustomed to the dark. If any unacceptable conditions
are noted, contact Customer Support
3.2.3. INSPECTION CRITERIA FOR PROPER IMAGE INTENSIFIER OPERATION
a. General
As directed in the Preventive Maintenance Checks and Services table, image intensier operation must
be checked before each mission. This section provides information for the operator concerning what
to look for, how to look for it, and how to determine if the MUNVM should be returned to the manufacturer.
CAUTION:
Perform the following inspection in the dark.
To perform this inspection, attach the monocular to the headmount as described in paragraph 3.3.7,
and turn the device ON. Look through the monocular and observe the image.
There are two groups of “defects” you may encounter – operational defects and cosmetic blemishes.
Operational defects are a denite reason for returning the MUNVM. Cosmetic blemishes are not necessarily a cause for rejection unless they become severe enough to interfere with the device’s operational
ability. The return of any MUNVM for cosmetic defects must be based on an outdoor evaluation and
not the TS- 4348/ UV Test Set.
b. Operational Defects
These defects relate to the reliability of the image intensier and are an indication of instability. If iden-
tied, they are an immediate cause for rejecting the MUNVM. They include shading, edge glow, ashing, ickering, and intermittent operation.
(1) Shading. If shading is present, you will not see a fully circular image (see Figure 3-3). Shading is very dark
and you cannot see an image through it. Shading always begins on the edge and migrates inward eventually
across the entire image area. Shading is a high contrast area with a distinct line of demarcation. Return the
MUNVM to the maintainer.
SHADING
Figure 3-3. Shading
Page 27
27
NOTE:
Always verify that shading is not the result of improper eye-relief adjustment (refer to paragraph 3.4.2).
(2) Edge Glow. Edge glow is a bright area (sometimes sparkling) in the outer portion of the viewing
area (see Figure 3- 4).
To check for edge glow, block out all light by cupping a hand over the objective lens. If the image intensier is displaying edge glow, the bright area will still appear. If edge glow occurs, you will need to
return the MUNVM to the manufacturer.
EDGE
GLOW
Figure 3-4. Edge Glow
(3) Flashing, Flickering, or Intermittent Operation. The image may appear to icker or ash. If there
is more than one icker, check for a loose battery cap or weak battery. If weak or loose batteries are not
the issue, you will need to return the MUNVM to the manufacturer.
c. Cosmetic Blemishes
These are usually the result of manufacturing imperfections that do not aect intensier reliability,
and are not normally a cause for returning an MUNVM. However, some types of blemishes can get
worse over time and interfere with the user’s ability to perform the mission. If you believe a blemish
is cause for returning the device, record the specic nature of the problem on the maintenance forms
and identify the position of the blemish by using the clock method and approximate distance from
the center (e.g., 5 o’clock toward the outside, 2:30 near the center, or 1:00 midway). The following are
cosmetic blemishes:
(1) Bright Spots. A bright spot is a small, non-uniform, bright area that may icker or appear constant
(Figure 3-5). Not all bright spots make the MUNVM returnable. Cup your hand over the objective lens to
block out all light. If the bright spot remains, you will need to return the MUNVM to the manufacturer.
Bright spots typically disappear when all light is blocked out. Verify that any bright spots are not simply
a bright area in the scene you are viewing. Bright spots are acceptable if they do not interfere with the
operator’s ability to view the image or to perform the mission.
EMISSI ON POINTS
BRIGH T SPOTS
Figure 3-5. Bright Spots and Emission Points
Page 28
28
(2) Emission Points. A steady or uctuating pinpoint of bright light in image area that does not go
away when all light is blocked from the objective lens of the monocular (Figure 3-5). The position of an
emission point within the image area does not move.
Not all emission points make the MUNVM returnable. Verify that any emission points are not simply a
point light source in the distance of the scene you are viewing. Emission points are acceptable if they
do not interfere with the operator’s ability to view the image or to perform the mission.
(3) Black Spots. These are cosmetic blemishes in the image intensier, or dirt or debris between the
lenses. Black spots are acceptable as long as they do not interfere with the operator’s ability to view the
image. No action is required if this condition is present, unless the spots interfere with the operator’s
ability to view the image or to perform the mission.
(4) Fixed-Pattern Noise. This is usually a cosmetic blemish characterized by a faint hexagonal (honeycomb) pattern throughout the viewing area. This most often occurs when operating in highly lit environments or when viewing very bright lights (see Figure 3-6). This pattern can be seen in every image
intensier if the level of light is high enough. This condition is acceptable as long as the pattern does
not interfere with the operator’s ability to view the image or to perform the mission.
Figure 3-6. Fixed-Pattern Noise
(5) Chicken Wire. An irregular pattern of dark thin lines in the eld-of-view either throughout the im-
age or in parts of the image area (see Figure 3-7). In the worst cases, these lines will form hexagonal or
square, wave-shaped lines. No action is required if this condition is present, unless it interferes with the
operator’s ability to view the image or to perform the mission.
Figure 3-7. Chicken Wire
Page 29
29
3.3 ASSEMBLY AND PREPARATION FOR USE
3.3.1. UNPACKING
The following steps must be taken prior to each mission in which the MUNVM is used.
CAUTION:
Relieve air pressure from inside the shipping and storage case by compressing opposite sides
of the case before releasing the latches.
(1) Release the latch securing the top of the shipping and storage case and open it.
(2) Verify that all items were shipped (see Figure 2-1).
(3) Open the carrying case (Figure 2-3), remove MUNVM, and inventory the items.
(4) Inspect the monocular for obvious evidence of damage to optical surfaces, body, eyecup, eyeguard,
power switch, battery cap, etc. Ensure that all optical surfaces are clean and ready for use. If necessary,
clean with dry lens paper.
3.3.2. INSTALLATION OF THE BATTERY
CAUTION:
To protect the image intensier, keep the objective lens cap securely tted over the lens when
the monocular is not in use or when it is being operated in daylight conditions.
The MUNVM operates with one AA batter y. The battery is not supplied with the MUNVM and must be
obtained separately.
At operating temperatures below -20°C (-4°F), Alkaline batteries are not recommended, as the battery
life will be severely reduced. Lithium-iron disulde L91 1.5V AA batteries should be used in conditions
below -20°C (-4°F).
TABLE 32. ESTIMATED BATTERY LIFE
BATTERY TYPE TEMPERATURE NEGLIGIBLE
IR SOURCE USAGE
AA Alkaline 21°C (70°F) 60 Hrs 55 Hrs
AA Lithium L91 21°C (70°F) 70 Hrs 65 Hrs
AA Alkaline -20°C (-4°F) 12 Hrs 10 Hrs
AA Lithium L91 -20°C (-4°F) 60 Hrs 55 Hrs
CAUTION:
Verify that the device is OFF before installing the battery.
Install the AA battery into PVS14 or 6015 as follows.
(1) Unscrew the battery cap.
(2) Align the polarity markings on the battery with those etched onto the battery compartment.
(3) Replace the battery cap and tighten it.
IR SOURCE
USAGE 10% OF TH E TIME
Page 30
30
SACRIFICIAL
WINDOW
EYECUP
DEMIST
SHIELD
BATTERY CAP
BATTERY
EYEGUA RD
Figure 3-8. Battery, Eyecup and Eyeguard Installation
3.3.3. INSTALLATION OF THE EYECUP OR EYEGUARD
Perform the following procedure to install eyecup or eyeguard onto the monocular. Refer to Figure
3-8.
(1) Carefully press the eyecup or eyeguard over the end of the eyepiece lens.
(2) Rotate the eyecup or eyeguard into proper viewing position. Adjust for the best t. The eyecup must
seal around your eye, preventing the green glow from leaking out.
3.3.4. INSTALLATION OF THE DEMIST SHIELD
Perform the following to install the demist shield on the eyepiece lens. Refer to Figure 3-8.
CAUTION:
If the demist shield needs to be cleaned, refer to paragraph 4.3.1 for instructions. Do not attempt to clean the demist shield while it is wet, or using wet lens paper; doing so will damage
the coating.
NOTE:
If inclement operating conditions are expected, (e.g. signicant temperature changes, high humidity, etc.), install the demist shield prior to the mission in order to reduce lens fogging.
(1) Carefully remove the eyecup or eyeguard.
(2) Carefully press the demist shield onto the eyepiece. Be careful not to smudge the eyepiece lens or
demist shield with your ngers or hands.
(3) Replace the eyecup or eyeguard (see paragraph 3.3.3).
3.3.5. INSTALLATION OF THE SACRIFICIAL WINDOW
Perform the following to install the sacricial window. Refer to Figure 3-8.
CAUTION:
If adverse operating conditions (e.g., large amounts of dust or sand) are expected, attach the
sacricial window prior to the mission to protect the objective lens from scratches or other
damage.
Page 31
31
(1) If the objective lens cap is in place, remove it.
(2) Carefully push the sacricial window onto the objective lens until it stops. Turn the sacricial window clockwise until it snaps into place.
3.3.6. INSTALLATION AND ADJUSTMENT OF THE HEADMOUNT
Perform the following to install the headmount.
NOTE:
Do not put the headmount on with the monocular attached.
(1) Before putting the headmount on, loosen the four ends of the chinstrap (approximately two inches
from the sliding bar buckles; see Figure 3-9).
(2) Snap the front and rear clasps (Figure 3-9) into place.
NOTE:
If the headmount is too loose, remove the attached thin browpad (Figure 4-3) and replace it
with either the medium or thick browpad (these are stored in the carrying case). Refer to paragraph 4.3.2 for removal and replacement of the browpads.
(3) Using both hands, grab the neck pad (Figure 3-9) and pull the harness over your head, sliding the
neck pad down over the back of your neck.
(4) Holding the chin cup in position, adjust both sides of the chinstrap until you feel it lightly press
against your chin. DO NOT TIGHTEN.
(5) Maintain the position of the chin cup and remove any slack from the chinstrap. DO NOT TIGHTEN.
CROSS-STRAP
CHIN CUP
VERTICAL
ADJUSTMENT
(HIDDEN)
SLIDIN G BAR
BUCKLES
CHINSTRAP
ADJUSTMENT
AND SNAP
NECK PAD
CHINST RAP
ADJUSTMEN T
AND SNAP
CHINST RAP
ADJUSTMENT
BROWPAD
(THICK , MEDIUM
OR THIN)
HEADMO UNT
SOCKET
EYE RELI EF
ADJUSTMENT
CHINST RAP
ADJUSTMENT
HEADBAND
Figure 3-9. MUNVM Headmount Adjustments
(6) Ensure that the cross-strap is not twisted. Remove any slack by adjusting the vertical adjustment of
the neck pad.
(7) Adjust the chinstrap and vertical adjustment until the chin cup and headband are in a comfortable
but rm position.
Page 32
32
NOTE:
After installing the monocular, minor strap adjustments may be necessary to achieve maximum
comfort.
(8) Install the headmount/ helmet mount adapter (refer to paragraph 3.3.7).
(9) Refer to paragraph 3.4.2 for operating procedures.
3.3.7. INSTALLATION OF THE HEADMOUNT/ HELMET MOUNT ADAPTER
To install the headmount/ helmet mount adapter (Figure 2-1) into the monocular, align the thumbscrew to the hole and tighten it as shown in Figure 3-10. An alignment boss on the headmount/ helmet
mount adapter ts into a groove on the monocular. Ensure that the boss on the adapter ts into the
groove on the monocular.
THUMBSCREW
LAT CH
ALIGNM ENT BOSS
(HIDDEN)
ALIGNM ENT BOSS
GROOVE
Figure 3-10. Headmount/Helmet Mount Adapter Installation
3.3.8. INSTALLATION OF THE HELMET MOUNT TO A HELMET
((1) Remove the helmet mount from the carrying case. Refer to Figure 3-11 for helmet mount features.
(2) Press the release (Figure 3-12) to remove the mount from the helmet mount bracket.
(3) Verify that the strap is laced onto the helmet mount bracket, as shown in Figure 3-12.
(4) With the catch pushed forward (see Figure 3-12), place the strap over the top of the helmet center
(see Figure 3-13).
(5) Hook the rear bracket (see Figure 3-12) on the center of the back of the helmet. Lay the strap, now
hooked to the helmet mount bracket, over the top of the helmet.
(6) Hook the helmet mount bracket to the center of the front lip of the helmet and hold it in place (see
Figure 3-13).
(7) With the buckle lever open, use the catch to remove the slack in the strap. Close the buckle lever.
(8) Disengage the neck strap latch on the left side of neck strap.
(9) Put the helmet on. Do not fasten the helmet chinstrap.
(10) Hold the neck strap where the strap meets the latch. Tighten the strap until it ts securely, then
install and tighten the helmet chinstrap. The brow of the helmet should be parallel to the ground, and
the helmet should be stable on the head.
Page 33
33
(11) Insert the top edge of the mount under the keeper on the helmet mount bracket and rotate it
downward until the latch engages (see Figure 3-13). To release the mount from the helmet bracket,
press the release and pull it forward and down.
KEEPER
NAPE
STRAP
HELMET
MOUNT
BRACK ET
REAR
MOUNTING
HOLE
CAT CH
BUCKLE
LEVER
STRAP
REAR
SNAP
REAR
BRACK ET
Figure 3-11. Installation of Helmet Mount
TOP EDGE
OF MOUNT
MOUNT IS R OTATED
MOUNT
RELEASE
90° FOR CL ARITY
KEEPER
HELMET
MOUNT
BRACK ET
STRAP
Figure 3-12. Helmet Mount
TOP EDGE
OF MOUNT
RELEASE
MOUNT
LAT CH
HELMET
MOUNT
BRACK ET
KEEPER
Figure 3-13. Reassembly of Helmet Mount
3.3.9. INSTALLATION OF TGE HEADMOUNT WITH A PROTECTIVE MASK
Perform the following to put the headmount on with a protective mask.
(1) Place the protective mask on your head per the instructions provided with the protective mask.
Page 34
34
WARN ING:
When installing the headmount over the protective mask, be careful that you do not break the
mask’s seal around your face.
(2) Install the headmount per the instructions in paragraph 3.3.6.
NOTE:
It may be necessary to remove the browpad (Figure 3-9) when wearing the headmount over a
protective mask.
3.3.10. INSTALLATION OF THE WEAPON MOUNT
Perform the following to install the weapon mount.
WEAPON
MOUNT
THUMBSCREW
CLAMPI NG KNOB
Figure 3-14. Weapon Mount Usage
ALIGNM ENT BOSS
(HIDDEN)
CAUTION:
The MUNVM is not a weapon sight. However, it can be used in conjunction with a collimated dot
sight or laser aiming device.
NOTE:
Armasight recommends replacing the eyecup with an eyeguard if mounting the device on a
weapon.
(1) Adjust the monocular and weapon mount as shown in Figure 3-14. Be sure to align the alignment
boss on the weapon mount with the alignment groove in the monocular.
(2) Screw in the thumbscrew to secure the monocular to the weapon mount.
(3) Loosen the clamping knob on the weapon mount. Position the weapon mount, now secured with
the monocular, onto the weapon’s mounting rail. Tighten it by turning the clamping knob.
NOTE:
There is a ratchet in the weapon mount that prevents over-tightening of the clamp. Turn it until
the knob clicks
Page 35
35
(4) Check the position of the monocular by holding the weapon in your normal ring position. Adjust
the fore/aft position of the monocular as necessary by loosening the clamping knob and repositioning
the weapon mount on the weapon’s mounting rail.
3.3.11. INSTALLATION OF THE COMPASS
CAUTION:
• Use of the compass with the plastic headmount or the plastic helmet mount will result in inaccurate compass readings. The magnet cannot be removed from these mounts.
• The magnet must be removed from the ruggedized metal helmet mount before installation of
the compass. Failure to do so will result in inaccurate compass readings.
• If the magnet is not removed, contact Customer Support for instructions on returning the ruggedized metal helmet mount for magnet removal. See Figure 3-15 for the location of the magnet.
(1) If the sacricial window or objective lens cap is in place, remove it.
(2) Turn the monocular on.
(3) While looking through the monocular, rotate the objective lens focus completely counterclockwise.
MAGNET
Figure 3-15. Locating the Magnet
Figure 3-16. Compass Installation
NOTE:
The o-ring must be correctly placed in the compass in order for the compass to t properly.
(4) Press the compass onto the objective lens at an angle using your left hand. Slowly turn the compass counterclockwise until it is in the vertical position, with the compass illumination button pointing
down (see Figure 3-16).
Page 36
36
(5) Ensure that the compass ts tightly to the objective lens.
(6) Refer to paragraph 3.4.6 for compass operation.
3.3.12. INSTALLATION OF THE 3X MAGNIFIER
The 3X magnier can be threaded directly into the objective lens. It can also be threaded into the focus
ring adapter and slipped on over the end of the objective lens.
Figures 3-17 and 3-18 illustrate these installation procedures.
THREA D DIRECTLY INTO
OBJEC TIVE LENS AS SHOW N
Figure 3-17. 3X Magnier Installation
FOCUS RIN G
3X MAGNIFIE R
ADAPTER
STEP 1
STEP 2
THREA D 3 X MAGNIFIER
INTO FOCUS R ING ADAPTER
Figure 3-18. 3X Magnier Installation with Focus Ring Adapter
3.3.13. MOUNTING MUNVM TO A WEAPON WITH A QUICKRELEASE PICAT
INNY MOUNT ADAPTER
The MUNVM is mounted to a weapon with a quick-release picatinny mount adapter (QRM) using the
optional bracket.
Mount the MUNVM to the QRM as follows:
1. Loosen the bracket clamp screw (A, Figure 3-19).
2. Put the bracket clamp (B) onto innity focusing stop ring (D) of the MUNVM objective lens.
3. Fix the MUNVM in the bracket clamp (B) by tightening the screw (A).
4. To unlock the clamping device (located on top of the QRM), see Figure 3-20. While pushing the lever
holder (C, Figure 3-20) down, turn the lever (B, Figure 3-20) towards the arrow (forward).
5. Install the MUNVM on the mount so that the stop (A, Figure 3-20) is inserted into the transverse slot
of the NVM rail.
6. Secure the MUNVM to the mount by turning the lever (B) to the locked position, as shown in Figure
3-20.
7. Verify that the clamping device is rmly secured to the MUNVM. If necessary, adjust the clamping
device.
MUNVM installed on the QRM is shown in Figure 3-21.
Page 37
37
C
B
D
A
Figure 3-19. MOUNTING OPTIONAL BRACKET TO THE MUNVM
A
B
C
Figure 3-20. CLAMPING DEVICE ON THE MOUNT TOP
Figure 3-21. QRM ASSEMBLED WITH MUNVM
3.3.14. MOUNTING A MUNVM TO A WEAPON WITH THE AIM ADVANCED
INTEGRATED MOUNT
The MUNVM is mounted to the AIM using the bracket from the AIM PVS14 Kit.
Figure 3-22. AIM ASSEMBLED WITH MUNVM
Page 38
38
The clamping system of the AIM is the same as is seen on the QRM. To mount the MUNVM to a weapon
with an AIM, see Part 3.3.13 of this Manual. This section describes mounting instructions and procedures for the QRM.
MUNVM installed onto the AIM is shown in Figure 3-22.
For more information on the use of an AIM, see the AIM Operation Manual.
3.4 OPERATING PROCEDURES
This section contains operating procedures for using the NVMPS as hand-held, head-mounted, helmetmounted or weapon-mounted monocular. Before operating the monocular, verify that all steps in section 3.3.3, Assembly and Preparation for Use, have been read and performed.
3.4.1. HANDHELD OPERATION
Only operate the monocular in dark environments; if it is necessary to operate the device in daylight,
use the objective lens cap to cover the objective lens.
NOTE:
When using the monocular without a mounting device, make sure to place the neck cord
around your neck.
(1) Ensure that the battery are installed per paragraph 3.3.2.
(2) Turn the power switch to ON.
NOTE:
The sharpest image will be observed only when the objective lens and eyepiece lens are properly focused.
(3) Rotate the diopter adjustment for the clearest view of the image intensier screen.
(4) Focus the objective lens while observing an object until the sharpest image is obtained.
3.4.2. HEAD MOUNTED OPERATION
Perform the following procedures for head mounted operation.
CAUTION:
Only operate the monocular in dark environments; if it is necessary to operate the device in
daylight, use the objective lens cap to cover the objective lens.
(1) Verify that the batteries are installed per paragraph 3.3.2.
(2) Put the headmount on per the instructions in paragraph 3.3.6.
NOTE:
Before attaching the monocular, depress the eye relief adjustment and slide the headmount
socket all the way forward; this will make it easier to align the monocular, eyecup, and eyepiece
lens to the eye.
(3) Align the headmount/ helmet mount adapter’s latch to the headmount socket (Figure 3-19). Hold
the latch lever down while installing the monocular into the headmount socket.
Page 39
39
Release the latch when the monocular is fully engaged in the socket.
(4) To set your eye relief, press down on the eye relief adjustment (Figure 3-19). Move the monocular
back towards your non-dominant eye until the eyecup is comfortably sealed around the eye.
(5) Turn the monocular ON.
(6) Readjust the vertical adjustment (Figure 3-9) of the headmount until the monocular is properly
aligned with your eye.
HEADMOUNT
SOCKET
LAT CH
EYE
RELIEF
ADJUSTMENT
Figure 3-23. Headmount/Helmet Mount Adapter Operation
NOTE:
The sharpest image will be visible only when the objective lens and eyepiece lens are properly
focused
(7) Rotate the diopter adjustment for the clearest view of the image intensier screen.
NOTE:
Any readjustment for eye relief requires readjustment of the diopter.
(8) To adjust the eye relief distance, press down on the eye relief adjustment. Slide the monocular either
forward or backward to obtain a full view of the image. Reset the diopter adjustment for the best image.
(9) While observing an object, adjust the objective lens focus (Figure 3-1) until the image becomes
sharp and clear.
3.4.3. HELMETMOUNTED OPERATION
CAUTION:
Take precaution when using/ handling the helmet mount. Most damage occurs when the helmet mount has been left on the helmet when it is not being used. Observe the following precautions to protect the helmet mount.
Page 40
40
CAUTION:
• To prevent damage, do not use excessive force when changing the up/ down position of the
MUNVM.
• Do not drop or throw the helmet with the helmet mount attached to it.
• If the monocular is ipped up, do not ick the monocular down by shaking the helmet. This
places signicant stress on the helmet mount.
• All Other Services – Return the helmet and the helmet mount to unit maintenance to have the
bracket directly mounted via the helmet screws.
NOTE:
The headmount/ helmet mount adapter allows the MUNVM to be rotated from the left to the
right eye or vice versa. The MUNVM can be ipped up with the headmount/ helmet mount
adapter positioned over either eye
NOTE:
The helmet mount allows the user to position the MUNVM in two ways: ipped up or ipped
down. When ipped down, the device is directly in front of the eyes. When ipped up, the unit
remains out of the line of sight. Both positions have a positive stopping point to indicate that
the device is positioned correctly.
Perform the following for helmet-mounted operation.
(1) Verify that the batteries are installed per paragraph 3.3.2.
(2) Put the helmet mount on per the instructions in paragraph 3.3.8.
(3) Place the monocular in the socket of the helmet mount.
Set your eye relief by depressing the side buttons (or, if using a metal mount, the side lever) (see Figure
3-24) and carefully move the monocular fore or aft until the eyecup comfortably seals around the eye.
Readjust the helmet straps as required for vertical adjustment.
PLASTI C MOUNT
TILT ADJUSTME NT
LOCK KNO B
SOCKET
SIDE
BUTTO NS (2 EA)
(FORE-AN D-AFT
ADJUSTMENT)
METAL MOUN T
TILT ADJUSTME NT
LEVER
SOCKET
SIDE LEV ER
(FORE-AN D-AFT
ADJUSTMENT)
Figure 3-24. Tilt and Flip-up Assembly Mechanisms
(4) Turn to the device ON. Adjust the tilt using the tilt adjustment lock knob, or tilt adjustment lever on
the metal mount (Figure 3-24), until you obtain a comfortable viewing angle.
Page 41
41
NOTE:
The sharpest image will be visible only when the objective lens and eyepiece lens are properly
focused.
(5) Rotate the diopter adjustment for the clearest view of the image intensier screen.
NOTE:
Any readjustment for eye relief requires readjustment of the diopter.
(6) Adjust the eye relief distance by depressing the side buttons (Figure 3-24) (or, if using a metal mount,
the side lever) and sliding the monocular back and forth until you obtain a full view of the image. Reset
the diopter adjustment for the best image.
(7) While observing an object, adjust the objective lens focus (Figure 3-1) until the image becomes
sharp and clear.
(8) To ip it up, grasp the helmet tilt and ip-up assembly and rotate upward and rearward until the
latch is rmly engaged.
WARN ING:
The monocular will not automatically turn o when ipped up. The monocular must be turned
o using the power switch.
(9) To ip the device down, grasp the helmet tilt and ip-up assembly and rotate downward and for-
ward until the latch is rmly engaged.
(10) Turn the device ON to resume viewing.
3.4.4. WEAPONMOUNTED OPERATION
NOTE:
The MUNVM can be used in conjunction with a collimated dot aiming device mounted on the
forward mounting rail. The brightness control for the aiming device should be set at or near its
minimum setting.
Perform the following procedures for weapon-mounted operation:
(1) Verify that the batteries are installed per paragraph 3.3.2.
(2) Attach the weapon mount to the monocular per paragraph 3.3.10, steps 1 and 2.
(3) Mount the monocular, with the adapter, to the M16/ M4 receiver rail, per paragraph 3.3.10, steps 3
and 4.
(4) Rotate the diopter adjustment for the clearest view of the image intensier screen.
(5) While observing an object, adjust the objective lens focus (Figure 3-1) until the image becomes
sharp and clear.
Page 42
42
3.4.5. IR SOURCE OPERATIONS
WARN ING:
The IR source is invisible to the naked eye, and is intended for use in extremely dark conditions.
However, this light can be detected by other night vision devices.
NOTE:
The IR source is intended for viewing at close distances (up to 3 meters) when additional illumination is needed.
(1) Pull the power switch knob out and rotate it clockwise to the IR position. With the monocular held to
the eye, verify that a red light appears in the eyepiece. This indicates that the IR source is operating.
(2) For momentary IR operation, turn the power switch clockwise (without pulling) past the ON position. Obser ve that a red light appears in the eyepiece.
3.4.6. OPERATION WITH A COMPASS
WARN ING:
The compass illuminator can be seen by others using night vision devices.
CAUTION:
You will get inaccurate readings, when using the compass on any head or helmet mount with
the magnet still installed. Only the magnet on the metal mount can be removed without causing damage to the equipment (see paragraph 3.3.11).
NOTE:
• The compass reading is magnetic North, not true North.
• The compass reading is within 2° of correct absolute magnetic bearing. Compass readings
with the mounted monocular (head mount or helmet mount) can be up to 15° of correct absolute magnetic bearing. This occurs mostly in the East (90°) to West (270°) and less in the North
(360°) to South (180°) reading. If the compass is inadvertently magnetized, this could cause an
additional 15° error.
• The objective lens focus can be ne-tuned after installation, but in order to obtain an accurate
reading, the compass must be vertical. (The compass image must be level.)
(1) Install per paragraph 3.3.11.
(2) To view a distant object more clearly, adjust the objective lens focus by gripping the compass and
turning it clockwise.
NOTE:
• Increase brightness slowly. Excessive brightness may burn a temporary image into the image
intensier. Do not increase brightness any more than is necessary to clearly read the compass
heading.
• The monocular must be focused at or near innity for proper compass operation.
Page 43
43
Figure 3-25. View Through Installed Compass
(3) To view the compass through the monocular, grip the compass with your index nger on top and
your thumb on the illumination button on the bottom. Press the button slowly with your thumb until
the proper brightness is obtained. The image should appear as shown in Figure 3-25.
(4) The compass readings should change when you move your head from side to side. Rotate or tap the
compass slightly to ensure that the compass is operating correctly. Hold the monocular in a level position to assure free rotation of the compass scale.
(5) The tick mark closest to the center of the lighted display is the compass bearing. The tick marks are
in degrees, with longer tick marks every ve degrees and bearing labels every 10 degrees.
3.4.7. OPERATION WITH A 3X MAGNIFIER
(1) Install per paragraph 3.3.12.
NOTE:
To allow focusing, the mated 3X magnier and objective lens will turn as a unit.
(2) While observing an object, grab the 3X magnier and adjust the focus until the image becomes
sharp and clear.
3.4.8. OPERATION WITH A GAIN CONTROL PVS14 ONLY
Turn the gain control (Figure 3-26) to balance the illumination input to the eye.
GAIN CONT ROL
Figure 3-26. Gain Control
Page 44
44
3.4.9. PREPARATION FOR STORAGE
(1) Perform the following to shut down the monocular.
(a) Turn the monocular OFF.
(b) Remove the monocular from the headmount, helmet mount or weapon, and remove the weapon mount from the monocular.
WARN ING:
Do not carry batteries in pockets containing metal objects such as coins, keys, etc. Metal objects
can cause the batteries to short circuit and become very hot when inserted into the device.
(2) Packaging After Use.
(a) Remove the battery cap and batter y.
(b) Inspect the battery housing for corrosion or moisture. Clean and dry if necessary.
(c) Replace the battery cap.
(d) If installed, remove the demist shield or sacricial window. Replace the objective lens cap.
NOTE:
• Prior to placing the MUNVM into the carrying case, verify that the MUNVM and the case are
both free of dirt, dust, and moisture.
• The monocular and helmet mount should not be left on the helmet when the helmet is removed.
(e) Refer to Figure 2-1 for proper placement of the demist shield, battery, carrying case strap, lens
paper, sacricial window, manual, browpads, headmount, helmet mount, headmount/ helmet mount
adapter and weapon mount.
(f) Place the monocular into the shallow pocket of the carrying case.
(g) Place the carrying case into the shipping and storage case; close and latch the case (Figure 2-3).
(h) Return the case to the storage area.
3.5 OPERATION UNDER UNUSUAL CONDITIONS
3.5.1. OPERATION IN DUSTY OR SANDY AREAS
CAUTION:
Operation in dusty or sandy areas can gouge and scratch the optical elements, and damage the
mechanical components. unless the below precautions are observed.
(1) Verify that the sacricial window is in place.
(2) Avoid pointing the monocular into the wind unless it is absolutely necessary.
(3) Keep the carrying case closed unless removing or replacing items.
(4) Ensure that all dust and sand is removed from the MUNVM and carrying case after operation.
Page 45
45
3.5.2. OPERATION IN RAINY OR HUMID CONDITIONS
CAUTION:
Operation in rainy or humid conditions can cause corrosion and deterioration of the MUNVM,
unless the below precautions are observed.
(1) Install the demist shield (paragraph 3.3.4).
(2) Keep the carrying case and the shipping and storage case closed unless removing or replacing
items.
(3) Dry the monocular, mounts, and accessories after exposure to rain or high humidity, and always
before storage. This will prevent mildew from forming in the case.
(4) Do not store the monocular in a wet carrying case or in a wet shipping and storage case.
3.5.3. OPERATION IN SALT WATER AREAS
After exposure to salt water, clean the MUNVM (paragraph 4.3.1).
3.5.4. OPERATION IN NUCLEAR, BIOLOGICAL AND CHEMICAL ENVIRON
MENTS
WARN ING:
Never reuse an eyecup or eyeguard that has been contaminated by hazardous materials or
environments. Contaminated eyecups and eyeguards must be replaced.
(1) Decontamination – Always wear a protective mask when decontaminating the MUNVM.
(2) Hardness – Do not use the DS-2 to decontaminate the MUNVM. To decontaminate the device, use
5% sodium hypochlorite and rinse with hot (158°F) soapy water.
Page 46
46
4
MAINTENANCE PROCEDURES
AND TROUBLESHOOTING
4.1 LUBRICATION INSTRUCTIONS
No lubrication is required.
4.2 TROUBLESHOOTING PROCEDURES
4.2.1. TROUBLESHOOTING
Table 4.1 lists common malfunctions that may occur with the equipment. Perform the tests, inspections
and corrective actions in the order they appear in the table.
This table does not list all of the malfunctions that may occur with your device, nor does it include all
tests, inspections, or corrective actions that may be necessary to identify and x defects. If you experience an equipment malfunction that is not listed, or suggested corrective actions do not correct the
fault, please contact Customer Support.
TABLE 41. OPERATOR’S TROUBLESHOOTING
MALFUNCTION TEST OR INSPECTION CORRECTIVE ACTION
1. Monocular fails to activate. Visual.
Check for defective, missing or
improperly installed battery.
2. IR source fails to activate. In a dark location with system turned
3. IR source indicator fails to
activate.
4. Poor image quality. Check objective lens or eyepiece lens
on, activate IR source.
Visually check IR source operation;
scene should brighten.
Visual. Please contac t Customer Support.
focus.
Check for fogging or dir t on objective
lens or eyepiece lens.
Turn the power switch to RESET/ OFF,
and then turn it ON.
Replace battery or install it correctly.
If IR source still fails to ac tivate, please
contact Customer Support.
Refocus.
Clean lens surfaces per paragraph 4.2.
Page 47
TABLE 41. CONTIN UED
MALFUNCTION TEST OR INSPECTION CORRECTIVE ACTION
5. Light visible around eyecup. Check eye relief distance.
Check eyecup for resiliency.
6. Diopter adjustment cannot
be made.
7. Battery cap dicult to open. Visually inspect for the presence of
8. Head straps cannot be tightened.
9. Headmount or helmet mount
socket and headmount/ helmet mount adapter latch does
not catch.
10. Helmet mount will not
tighten to helmet.
11. Helmet mount is damaged. Visual. Please contact Customer Support.
12. Compass will not stay on
the goggles.
13. Compass display is not
cle ar.
14. Monocular does not cut o
when exposed to high light.
Check to see if the diopter adjustment is bent or broken.
an o-ring.
Check for damaged battery cap.
Check for defective buckles, fasteners or straps.
Check socket or latch for dirt.
Check socket or latch for damage.
Inspect mounting hardware for
damage.
Visual. Please contac t Customer Support.
Visual Make sure the monocular is focused
Visual.
Perform the following test under
daylight or bright room light (not
uorescent light).
Place the objective lens cap on the
objective lens. Turn monocular ON
and obser ve that it cuts o within 70
±30 seconds after energized.
Turn monocular OFF and then ON to
reenergize monocular.
Readjust for proper eye relief
distance.
If eyecup is defective, please contact
Customer Support.
If damaged, please contact Customer
Support.
If o-ring is missing, please contact
Customer Support.
If damaged, please contact Customer
Support.
If damaged, please contact Customer
Support.
Clean socket and latch.
If damaged, please contact Customer
Support.
If damaged, please contact Customer
Support.
for innit y. If it is focused but the
compass display is still not clear,
please contact Customer Suppor t.
If damaged, please contact Customer
Support.
4.3 OPERATOR’S MAINTENANCE PROCEDURES
4.3.1. CLEANING THE MUNVM
CAUTION:
• The monocular is a precision electro-optical instrument and must be handled carefully.
• Do not scratch the external lens surfaces or touch them with your ngers.
• Wiping the demist shield with lens paper while wet or with wet lens paper can damage the
coating.
If necessary, clean the monocular with water and dry it thoroughly. Clean the lenses with lens paper
(and, if necessary, water, with the exception of the demist shield).
47
Page 48
48
4.3.2. HEADMOUNT MAINTENANCE
a. Browpad Replacement
Replace the browpad when cracked, torn, or contaminated. Perform the following to remove and replace the browpad.
(1) Firmly grasp the headmount and remove the old browpad.
(2) Gently press on the new browpad. Gently smooth out any wrinkles in the new browpad.
b. Neck Pad Reinstallation
During operation of the MUNVM, it is possible for the neck pad to become separated from its position
on the headband. Perform the following to reinstall the neck pad.
(1) Lift the upper headband strap retention tab (see Figure 4-1), allowing space for the neck pad strap
to be inserted underneath.
(2) Slip the neck pad strap all the way under the upper strap retention tab; pull the lower part of the
neck pad strap under the lower strap retention tab.
(3) If necessary, repeat steps 1 and 2 for the other side of the headband and neckband.
NECK PAD STRA P
UPPER STR AP
RETEN TION TAB
LOWER STR AP
RETEN SION TAB
Figure 4-1. Reinstalling the Neck Pad
c. Lacing the Sliding Bar Buckles
MOVEABLE
SLIDIN G BAR
Figure 4-2. Threading the Sliding Bar Buckles
FIXED
SERRATED B AR
Page 49
49
When putting on and adjusting the headmount, it is possible for the strap to slip out of the slide fastener. Perform the following to adjust the strap and sliding bar buckle.
(1) Thread the strap from the inside of the buckle over the moveable sliding bar (see Figure 4-2.). Thread
the strap back through the buckle; this time, thread it under the moveable sliding bar and over the
serrated part of the buckle.
(2) Pull the strap through the buckle and tighten.
(3) Repeat steps 1 and 2 for other straps and buckles that have come undone.
4.3.3. NECK CORD MAINTENANCE
The neck cord (Figure 2-1) may be broken, frayed, or the ends may come untied.
If loose, re-tie the ends of the cord. If broken or severely frayed, install a new cord as follows:
(1) From the rear, insert the ends of the cord through the holes in the monocular.
(2) Thread the end of the right cord through the hole in the objective lens cap.
(3) Tie a knot at each end of the cord.
4.4 SERVICE/PACKING AND UNPACKING
4.4.1 RETURN INSTRUCTIONS
For service, repair or replacements, please email service@armasight.com.
To assist the Service Representative (SR) in determining if the item is repairable, please provide the
following information:
(1) Serial Number of the defective item.
(2) Thorough description of the malfunction, defect or damage.
(3) An explanation of how the malfunction, defect or damage occurred, if known.
If the SR determines that the item is under warranty or should be returned for repair, a Return
Material Authorization number (RMA#) will be provided. RMA can be obtained via e-mail to
service@armasight.com or via phone by calling Armasight Customer Service at (888)959-2259 Ext. 2 or
via fax (888)959-2260.
When returning the PVS-14/ 6015 for service or repair, the following should be done to prevent any
additional damage:
(1) Verify that the device is free of all contaminants, such as dirt or other foreign material.
(2) Remove the batter y.
(3) Place the cap over the lens.
(4) Place the PVS-14/ 6015 into a hard shipping/ storage case or soft carrying case (if available). If the
hard shipping/ storage case is not available, you will need to individually package each unit being
returned in a suitable container.
Place the PVS-14/ 6015, as well as a copy of the test report or detailed description of the failure, in a suitable packing/ shipping container. Mark the package with the RMA#. Ship the items using the fastest,
most easily traceable, prepaid method to Armasight Inc., 815 Dubuque Avenue, South San Francisco,
CA 94080, USA.
Page 50
50
APPENDIx
A. COMPONENTS OF END ITEM COEI AND BASIC ISSUE
ITEMS BII LISTS
A1. SCOPE
To help you inventory components and to promote safe and ecient operation of the equipment, this
appendix lists COEI and BII for the PVS-14/ 6015.
A2. GENERAL
The COEI and BII information is divided into the following lists:
Components of End Item (COEI). This list is for information purposes only, and is not a basis for requesting returns or replacements. These items are part of the PVS-14/ 6015. As part of the end item,
these items must be with the end item whenever it is issued or transferred between property accounts.
Items of COEI are removed and separately packaged for transportation or shipment only when necessary. Illustrations are furnished to help you locate and identify the items.
Basic Issue Items (BII). These essential items are required to prepare the PVS-14/ 6015 for operation,
properly operate the device, and perform any necessary emergency repairs. Although shipped separately, BII must be used with the
PVS-14/ 6015 during operation and when it is transferred between property accounts. Listing these
items is a basis for requesting replacement items, based on authorization of the end item by the TOE/
MTOE. Illustrations are provided to help you identify the items.
A3. EXPLANATION OF COLUMNS IN THE COEI LIST AND BII LIST
Column (1), Illus. Number. Gives you the number of the item illustrated.
Column (2), National Stock Number. Identies the stock number of the item to be used for requisition-
ing purposes.
Column (3), Description CAGEC and Part Number. Identies the Federal item name (in all capital letters) followed by a minimum description when needed. The stowage location of COEI and BII is also
included in this column. The last line below the description is the CAGEC (commercial and Government
entity code) (in parenthesis) and the part number.
Column (4), Usable on Code. When applicable, gives you a code if the item you need is not the same
for dierent models of equipment.
Column (5), U/M (Unit of Measure). Indicates how the item is issued for the National Stock Number
shown in column (2).
Column (6), Qty Rqr. Indicates the quantit y required.
Page 51
4
3
1
2
5
8
7
6
10
9
20
11
12
15
16
19
13
17
14
18
Figure A-1.Components of End Item
TABLE A1. COMPONENTS OF END ITEM
1
ILLUS.
NUMBER
1 MONOCU LAR ASSEMBLY(80063) A32563 40 EA 1
2 5855 -01-246- 8271 WINDOW, SACRI FICIAL(80063) A3144264 EA 1
3 5855-01-444-1230 LENS, INFRA RED RECEIVER(80 063) A3256353 EA 1
4 5 855- 01-3 79-1410 FILTER, IN FRARED LIGHT(54 490) 5009737 EA 1
5 5855-01-246-8266 HEADSET AS SEMBLY(80063) A3144268 EA 1
6 5 855- 01-297-78 47 BROWPAD ASS Y, THICK(80 063) A3144436 EA 1
7 5855 -01-355-8 600 BROWPAD ASSY, MEDI UM(80063) A3144435 EA 1
8 5855 -01-355-8 599 BROWPAD ASSY, THIN (80063) A3144280 EA 1
9 5965-01-444-1216 ADAPTER, H EADSET(80063) A3256 347 ANAM000019 EA 1
10 5340-01-446-8588 BRACK ET, MOUNTING(80 063) A3256348 ANAM000007 EA 1
11
12 5855 -01-381- 6052 COMPASS ASS EMBLY(8006 3) A3187430 ANKI000009 EA 1
13 6650- 01-444 -1229 EYEGUARD, O PTICAL INSTR UMENT(80063) A3256345 ANEC000004 EA 1
14 534 0- 01-45 1-7737 CLIP, RETAINING(800 63) A3260933 EA 1
15 5855 -01-39 8-428 4 CA SE, INFRARED EQUI PMENT(80063) A3187392 AGHC000003 EA 1
16 534 0-01 -250-24 31 STRA PPING(80063) A3144267 EA 1
17 5340 -01-397-6608 CAP, PROTECT IVE, DUST(80063) A 3144318 EA 1
18 4020-01-446-8097 CORD, FIBR OUS(80063) A3144306 EA 1
19 OPERATOR’S M ANUALTM 11-58 55-306-10 EA 1
20 CASE, SHIPPING & S TORAGE(80063) A326 4350 AGHC000001 EA 1
2
NATIONAL STOCK
NUMBER
5855 -01- 457-2953
5855 -01-4 41-04 01
3 DESC RIPTION, CAGE C, AND PART NUMBE R
MOUNT, VIE WER(80063) A3256368 or
MOUNT, VIE WER(80063) A3260927
4
USABLE ON
CODE
ANHM000005
5
U/M
QTY
RQR
EA 1
6
51
Page 52
52
B. ADDITIONAL AUTHORIZATION LIST AAL
B1. SCOPE
This appendix lists additional items you are authorized to use to supplement the PVS-14/ 6015.
B2. GENERAL
This list identies items that do not have to accompany the PVS-14/ 6015 and that do not have to be
returned with it. These items are all authorized for your use by CTA, MTOE, TDA, or JTA.
B3. EXPLANATION OF COLUMNS IN THE AAL
Column (1), National Stock Number. Identies the stock number of the item to be used for requisition-
ing purposes.
Column (2), Description, Commercial and Government Entity Code (CAGEC), and Part Number
(P/N). Identies the Federal item name (in all capital letters) followed by a minimum description when
needed. The last line below the description is the CAGEC (in parentheses) and the part number.
Column (3), Usable On Code. When applicable, gives you a code if the item you need is not the same
for dierent models of equipment.
Column (4), U/M (Unit of Measure). Indicates how the item is issued for the National Stock Number
shown in column (1).
Column (5), Qty Recm. Indicates the quantity recommended.
TABLE B1. ADDITIONAL AUTHORIZATION LIST
1 NATIONAL STOCK
NUMBER
6135-00-9 85-7845 BATTERY, NONREC HARGEABLE (AA), 1.5 Vdc (8 0058) BA-3058/U EA 2
6135-01-333-6101 BATTERY, NON RECHARGEABLE (A A) (83740) L91, 1.5 Vdc EA 2
6625- 01-323-958 4 TES T SET, ELEC. SYS. TS- 4348/UV (800 63) A3139775 EA 1
5855-01-423 -0817 MAGNIFIER L ENS ASSEMBLY (80063) A3256391 EA 1
2 DESC RIPTION, CAGE C, AND PART NUMBE R
3 USABLE ON
CODE
4
U/M
5
QTY
RECM
Page 53
53
C. EXPENDABLE AND DURABLE ITEMS LIST
C1. SCOPE
This appendix lists expendable and durable items that you will need in order to operate and maintain
the PVS-14/ 6015. This list is for information only and is not basis for requesting returns.
C2. EXPLANATION OF COLUMNS IN THE EXPENDABLE/DURABLE ITEMS
LIST
Column (1) - Item Number. This number is assigned to the entry in the list and is referenced in the nar-
rative instructions to identify the item.
Column (2) - Level. This column includes the lowest level of maintenance that requires the listed item
(C = Operator/Crew).
Column (3) - National Stock Number. This is the NSN assigned to the item, which you can use to requisition it.
Column (4) - Item Name, Description, Commercial and Government Entity Code (CAGEC), and Par t
Number (P/N). This column provides the other information you need to identify the item.
Column (5) - Unit of Measure (U/M). These codes show the physical measurement or count of an item,
such as gallon, dozen, gross, etc.
TABLE C1. EXPENDABLE AND DURABLE ITEMS LIST
1 ITEM
NUMBER
2 LEVEL 3 NATIONAL STOCK NUMBER 4 ITEM NAME, DES CRIPTION, C AGE, PART NUMBER 5 U/M
1 C 6640- 01-459-4239 PAPER, LENS (81348) A-A- 50177, TYPE I, CLASS 5 PK
Page 54
54
D. PRODUCT WARRANTY REGISTRATION CARD
ARMASIGHT PRODUCT WARRANTY REGISTRATION CARD
PRODUCT INFORMATION
CUSTOMER INFORMATION
Product Name
Purchase Date
Name
Purchased From
Product Serial #
Address
City
Day Phone #
E-mail address
Country Zip
Home Phone #
Customer Signature Required
In order to validate the warranty on your product, Armasight must receive a completed Product Warranty Registration Card for each unit, or the user must complete warranty registration on our website
(www.armasight.com). Please complete the included form and immediately mail it to our Service Center: Armasight Inc., 815 Dubuque Avenue, South San Francisco, CA 94080, USA
Page 55
55
ALPHABETICAL INDEX
A
Abbrevi ations, list of 10
Additio nal Authorizati on List 52
Adjustm ent (See specic ad justment)
Ambient te mperature limi ts 11
B
Basic Issu e Items List 50
Batter y
AA size 15
Alkalin e 15
Install ing 29
Life 29
Lithium 15
Low batte ry indicator 12, 19
Polarit y Indicators 29
Voltage 15
Black spo ts 11, 28
Bright sp ots 11, 8
Browpad s 11, 13, 31
C
Capabil ities 12
Charac teristics 15
Check s, preventive maint enance 20
Chicken wi re 11, 25
Cleaning t he MUNVM 47
Compass
Install ation 35
Operat ion 42
Compone nts of End Item List 5 0
Corrosio n prevention and co ntrol 11
D
Dark (or dark a rea) 11, 25
Data 15
Elect rical 15
Environm ental 15
Equipme nt 15
Mechani cal 15
Optical 15
Demist S hield
Descrip tion 12
Install ation 30
Diopter 15
Diopter A djustment 11, 16, 22
E
Edge glow 11, 27
Elect ronic circuit func tion 17
Equipment
Charac teristics, cap abilities and fe atures 12
Data 15
Expen dable and Durab le Items List 53
Eye Relie f 16
Eyecup, ins tallation 30
Eyeguard , installation 30
Eyepiece l ens
Focus 12
Operat ion 16
F
Features 12
Field-of-view 15
Fixed- pattern noise 11, 28
Flashing 11, 22, 26
Flickerin g 11, 22, 26
Focus
Eyepiece (s ee Eyepiece lens)
Objec tive (see Objec tive lens)
G
Gain contr ol 12, 15, 16, 18, 43
Glossa ry 10
H
Hand- held operatio n 38
Headmo unt/Helmet m ount adapter inst allation 38
Head Mou nt
Install ation 38
Maintenance 47
Operat ion 38
Helmet M ount
Install ation and adjustm ent 32
Install ation with protec tive mask 33
Operat ion 40
High Light Cu t-O 17
Honeyco mb (see Fixed-pa ttern noise)
Humid con ditions 45
I, J, K
Illumina tion required 15
Image inte nsier operati on 26
Innit y focus 11
Inspection
Criteria f or proper image i ntensier oper ation 26
Preventiv e maintenance 20
IR source o perations 42
L
Latch 19, 47
LED On Indi cator 11
Lithium b attery (see Bat tery)
Locatio n and descriptio n of major compone nts 12
Low batte ry indicator
Descrip tion 12, 19
Operat ion 19
Lubrica tion 46
M
Magnic ation 15
Maintenance
Cleaning t he MUNVM 47
Headmo unt 47
Neck Cord 49
Mechani cal data 15
Mechani cal function s 16
N
NBC enviro nments 45
Neck cord 13, 48
O
Objec tive lens
Focus 15
Functio n 16
Locatio n 16
Operat ing temperature 15
Operat or adjustment lim its 15
Operat or controls and indi cators 19
Optical
Data 15
Functio ns 15
P
PMCS 20
Power
Source 15, 16
Swi tch 16
Prepara tion for storage 44
Purpose o f equipment 17
R
Rainy cond itions 45
Resolut ion check using th e TS-4348/U V Test Set 24
S
Sacric ial Window
Descrip tion 12
Install ation 31
Salt wate r areas 45
Sandy con ditions 45
Shading 11, 26
Shutdown (s ee Preparation f or storage)
Storage te mperature 15
T
Temperatur e limits 15
Test Set, TS -4348/UV 24
Troublesho oting 46
3X Magnie r
Install ation 38
Operat ion 43
U, V
Unpack ing 29
Vertica l adjustment 40
Voltage 17
W, X, Y, Z
Warning 12
Warrant y Information 8
Weapon mo unt
Descrip tion 15
Install ation 34
Weapon Mo unted
Operat ion 41
Page 56
Armasight Inc.
815 Dubuque Avenue,
South San Francisco,
CA 94080, USA
Phone: (888)959-2259
Fax: (888)959-2260
Intl Phone/Fax: (650)492-7755
info@armasight.com
CAUTION:
This product contains natural rubber latex
which may cause allergic reactions! The FDA
has noted an increase in the number of reported
deaths that are associated with an apparent sensitivity to natural latex proteins. If you are allergic
to latex, it is a good idea to learn which products
contain it and strictly avoid exposure to those
products.
www.armasight.com
Loading...