Assembly&Instruction Manual
10x12ft
ergola
Installation
Guide
10ft
Save this manual for future reference
12ft
INTRODUCTION
Thank you for purchasing ' ! We hope you will find joy in our Aoodor s Patio pergola
product for many years to come.
To ensure your personal safety during installation and to get the most out of your investment, please read this entire
manual before beginning the installation process. If you feel that this process is too di cult to do on your own, we advise ffi
that you seek assistance from a local building or home improvement contractor.
WARNING Improper installation and operation of your awning can result in
severe personal injury as well as product failure not covered by warranty. Please
follow all instructions carefully or contact technical support for assistaince.
We believe that installation can be a simple, streamlined process if you follow the instructions in this manual.
Estimated Assembly Time 1 2 hours
: - .
2
Parts list
Parts Desc Qty Ref No
800 044 001- -
A1
A2
B2
C1
C2
D
S1
S2
4
800 044 002- -
2
800 044-003-
2
800 044-004-
1
800 044-005-
1
800 044-006-
2
800 044-007-
2
800 044-008-
2
Parts Desc Qty Ref No
I 1
I1 2
J 16
K 16
L 4
M 8
N 1
O 6
800-044-020
800 044-021-
800 044-022-
800 044-023-
800 044-024-
800 044-025-
800 044-026-
800-044-027
E1
E2
F1
F2
G
H
H1
H2
AA
800 044-009-
1
800 044-010-
1
800 044-011-
2
800 044-012-
2
800 044-013-
1
800 044-014-
5
800 044-015-
2
800 044-016-
2
800 044-017-
1
P 32
Q 2
R 20
T 4
U 1
V 14
W 4
X 2
Y 4
800 044-028-
800 044 029
- -
800 044-030-
800 044 031
- -
800 044 032
- -
800 044 033
- -
800-044-034
- -
800 044 035
800-044-036
AB
AC
AD
1
2
4
800-044-018
800-044-019
800-044-040
Z 8
Z1 8
AE 3
800-044-037
800-044-038
800-044-039
3
Assembly
1
C
x1
D
x1
E
x1
S
x2
F
x2
K
x16
Step1:Beam assembly.
1.Connect (C1) with (C2) together using screw(K) tightly to beca me Side Bea m(C)
2.Connect (D ) to (D) with connector(AE) together using screw(K) tightly to became M iddle Cross
Beam(D)
3.Connect (E1) with (E2) together using screw(K) tightly to became Side Beam(E)
4.Connect (S1) with (S2) together using screw(R) tightly to became Cross Beam(S)
5.Connect (F1) with (F2) together using screw(K) tightly to beca me cross Beam(F)
R
x16
2
4
Assembly
2
x1
N
x1
Step2:Mi ddle cross beam assembly
Insert the Hook pull ey as the figu re sh own above.(N)x1,(L)x3,(I)x1. And cover the beam c ap(V).
L
x4
I
x1
3
x2
x8
I1
x2
M
I1
Step3:Cross beam assembly
Insert the Hook pull ey (M ) And cover the bea m cap.
Note:Repeat this step for whole Beam(F).
V
x2
V
x4
4
B2
W
x4
W
Step4:Post assembly
1.connect post(A1) to post(B2) with connector( T) and using bolt (R) ,become Post(B)
2.connect post(A1) to post(A2) with connector(T) and using bolt (R),become Post(A)
Note:
1.Before assem bly post, please turn th e bolt (R)o ut of connector(T) firstly.
2.Repeat this step for all post.
A2
T
x4
A1
B
x2
T
A1
A
x2
A1
5
Assembly
5
Step5:Post and Side Beam assembly
1.Connect Post (B) an d Post(A) to beam ( C using bolt( P)）
2.Connect Post (B) an d Post(A) to beam ( E using bolt(P)）
Note:Repeat this step for all posts and beams.
3.Cover the beam cap(V).
V
x16
P
x4
x 1
6
Assembly
6
Fig 6 1. .
J
Fig 6 1. .
Fig 6 3. .
H1
Q
Fig 6 2. .
R
x16
P
Step6:Post and Cross Beam assembly
1.Connect Post (B) and Post(A) to Cross beam ( F using bolt(P),see fig.6.1）
Note:Repeat this step for all Cross beam (F).
2.Insert the post mount to the post an d fix wit h bolt R see fig 6 2( ). . .
3.Connect the support bar(H1)together using bolt(Q ).see fig.6.3
4.Install the suppor t bar(H1) to post(A)and post (B)using bolt (J).
Note:there are 2 positions on ea ch post, and please mounting this according to your sit uation.
J
x8
x4
Q
x2
x 1
7
Assembly
7
Fig.7.1
Fig.7.2
O
x4
Step7:Cross Beam assembly
1.Attach Cross beam (S) to the Side beam (C)and (E) and fix with bo lt(O),see Fi g.7.1 and Fig.7.2
2.Cover the beam cap(V)
Note:Repeat this step for all Cross beam (S).
V
x4
x 1
8
Assembly
8
Fig.8.3
Fig.8.4
Fig.8.1
Fig.8.2
Step8:Fabric roof assembly.
1.Insert the Pole (H)and (G) through the fabric.
2.Insert the pole(H) through the pulley( I) a nd fabric (U ).see Fig.8.1 and connect the pol e(H)
together.see Fig.8.2
3.Insert the pole(G) through the pulley(N) and fab ric (U).see Fig.8.3 and conn ect the p ole(H)
together.see Fig.8.4.
9
J
x4
AD
x4
Step9:Curtain install
1.Attach the bracket(AD) to the cur t ain(H2) usin g bolt(J) .
Note:There are 2 curta ins for thi s pergola
9
Assembly
10
Fig.10.1
Fig.10.1
Fig.10.2
O
x2
Step10:Roof instal l.
1.Attach Middle Cross beam (D) to the Side be am (C)and (E) and fi x with bolt(O),see Fig.10.1
2.Attache the cur tain(H2) to beam(C),and using bolt (J).see Fig.10.2
J
x4
10
Assembly
11
Fig.11.1
Fig.11.1
Step11:Roof instal l.
1.Fasten the tube(G) to th e beam(C),and using bol t (X).see F ig.11.1
X
x2
Assembly
11
I1
Fig.12.3
Fig.12.1
Hard ground
M
Fig.12.2
Soft ground
Step12:Fabric assembly
1.Turn the bol t out from pole (H) see Fig.12.1and insert the pole through the pulley hook(M) , then turn
bolt in.Fig.12.2
Note:Repeat this step for all poles.
2.Turn the plastic bolt cap to fi x the roof.see Fig.12.3
12
Loading...