Arlec ALD023, ALD024, ALD022, ALD021 User Manual

Warranty

Arlec guarantees this product in accordance with the
Australian Consumer Law.

Arlec also warrants to the original first purchaser of this
product (“you”) from a retailer that this product will be free
of defects in materials and workmanship for a period of 12
months from the date of purchase; provided the product
is not used or installed other than for the purpose, or in a
manner not within the scope of the recommendations and
limitations, specified by Arlec, is new and not damaged
at the time of purchase, has been properly installed by
a licensed electrician or contractor who is licensed to
install electrical products in the place in which the product
was installed and in accordance with Arlec’s installation
instructions, has been maintained in accordance with
the recommendations specified by Arlec, has not been
subjected to abuse, misuse, neglect or damage, has not
been modified or repaired without the approval of Arlec
and has not been used for, or installed in premises which
are used for, commercial purposes (“Warranty”).

If you wish to claim on the Warranty, you must, at your
own expense, return the product or that part of the
product which you believe is defective in materials and
workmanship, and provide proof of original purchase, your
name, address and telephone number and a certificate
of installation or other document required by law for the
installation of electrical products in the place in which the
product was installed issued by the licensed electrician
or contractor who installed the product, to Arlec at
the address below within 12 months from the date of
purchase. Please note that the Warranty does not cover
removal or re-installation of the product or that part of the
product which you believe is defective.

Arlec will assess any claim you may make on the Warranty
in the above manner and if, in Arlec’s reasonable opinion,
the Warranty applies, Arlec will at its own option and

expense replace the product (or part of the product) with
the same or similar product (or part of the product) or
repair the product (or part of the product) and return it to
you or refund the price you paid for the product. Arlec will
bear its own expenses of doing those things, and you must
bear any other expenses of claiming on the Warranty.

The Warranty is in addition to other rights and remedies
you may have under a law in relation to the product to
which the Warranty relates.

Our goods come with guarantees that cannot be excluded
under the Australian Consumer Law.
You are entitled to a replacement or refund for a major
failure and for compensation for any other reasonably
foreseeable loss or damage. You are also entitled to have
the goods repaired or replaced if the goods fail to be of
acceptable quality and the failure does not amount to a
major failure.

Arlec Australia Pty. Ltd.
ACN 009 322 105 (“Arlec”) gives the Warranty.
Arlec’s telephone number, address
and email address are:

Customer Service:
New Zealand Toll Free: 0800 003 329

Building 3, 31 – 41 Joseph Street,
Blackburn North, Victoria, 3130

Blackburn North LPO, P.O. Box 1065,
Blackburn North, 3130

Email: [e-mail]

[phone]

Instructions 120mm x 120mm B&W_CPIN002966

LED Downlight

5W

Kit

CPIN 002966

Instructions

ALD021, ALD022, ALD023 & ALD024

Instructions 120mm x 120mm B&W_CPIN002966

Installation Information

WARNING!

Please ensure the following safety warnings are observed:

• This product complies with AS/NZS

60598.2.2 type IC recessed luminaire
requirements, where suitable building
insulation may abut and cover the dowlight
[not the driver].
Refer to the CA 80ºC mark, which appears
on the product below.

• This product is suitable for use with

building insulation that can safely be
continually exposed to temperatures up to
90°C and withstand a 30s needle flame test
carried out in accordance with

AS/NZS 60695.11.5 with the ame applied

to all surfaces of the insulation.

• Loose ll insulation as dened in NZS

4246 is not permitted to abut or cover this
luminaire [including the driver].

• Glass bre insulation is a suitable insulation

for use abutting this luminaire.

• Read the instructions prior to installation or

use. Please retain the instructions for future
reference.

Bulb supplied is LED 5W and is not a dimmable type.

Max bulb is 35W incandesent GU10 type can be used in this luminaire.

LED bulbs are recommended for long life and energy efcient

• Before attempting to install or maintain,

ensure the power is switched OFF.

• Installation in circuits protected by safety

switches (Earth leakage circuit breakers) is
recommended.

• Use only on rated voltage, otherwise

damage may occur.

• Do not allow the xture to come into

contact with liquids.

• Ensure the xture is fully assembled before

energizing.

• There are no user replaceable components
in this xture.

• Not suitable for use near ammable liquids,

vapour, gases or in explosive environments.

• If the supply cord is damaged it must only

be replaced by the service agent or similar

qualied person in order to avoid a hazard.

Complies with AS/NZS 60598.2.2
Insulating Ceiling CA80º C Mark
refer to in stallation i nformation

This luminaire is suitable for permanent
installation indoors. The mounting must
be in a rigid and dry location.

1. Ensure the power to the circuit being
connected to is isolated.

2. Remove xture from carton and remove

all packing materials.

3. Select a suitable mounting position.

4. Allow a minimum clearance of 40mm
between the lamp (top and sides) and
adjacent structural members and
building elements.

5. Cut a 70mm diameter hole in
mounting surface.

6. Wire supply to terminal block.

7. Lift the remaining clips and secure lamp
housing in position.

8. connect bulb supplied to lamp base
connector.

9. Fit bulb into front ring and lock in place.

10. Energise the circuit and check that the

lamp operates.

11. Dispose of any packaging material.

Combustible building element above fitting.

HCB > 10mm

MIC > 20mm

TERMINAL

Thermal Insulation

SCB > 40mm

Ceiling

Joist

RISK OF FIRE

Building insulation must not

cover this luminaire

SCB > 40mm HCB > 10mm MIC>20mm

SCB = Minimum distance between the side

of the recessed luminaire and any building

element as specied in AS/NZS 3000 or as
specied by the luminaire manufacturer.

HCB = Minimum distance as specied by the

luminaire manufacturer between the top of
the recessed luminaire and any building element
above it.

MIC = Minimum distance as specied by the

luminaire manufacturer between the top
of any building insulation and the building
element above it.

70mm

130mm

80mm