Arkon SM523-G User Manual
SM523-G
|
Cup Holder Mount with Flexible Goosneck Shaft with Slim-Grip™ Smartphones
SM050-2 Slim-Grip™
Universal Phone Holder
88mm exp andable to 138mm
with Ex tra Long Suppor t Legs
Cup Holder Mounting
Step 1.
Step 2.
Step 3.
Connect the gooseneck shaft (A) to the cup holder base (B) by
aligning the groove on the base to the ridge inside of the bottom
of the shaft.
(C) Thumb wheel
adjustment
knob
Place the Universal Cup Holder Mount into the designated cup
holder in the vehicle. Adjust the thumb wheel adjuster (C) to open
or close the cup holder prongs to t in the cup holder.
For oversize cup holder openings or the adjustable “pop out” cup
holders use the optional self-adhesive side support pads (D). Install
the pads by removing the adhesive backing and placing it on the
at surface side of the cup holder support leg.
Package Contents:
(1) GN033-SBH - 5” Cup holder mount with exible gooseneck shaft
(1) SM050-2 Universal phone and portable device holder
(1) SP-SM050-LF - Extra Long Support Legs (2 Pack) for larger phones
Holder i ncluded is Univer sal, designed to t nearly ALL non- ip mobile phon es regardless of wh ether a
protec tive case or silicon e sleeve is attac hed to the phone.
SP-SM050-LF
Extra Long
Support Legs
(2 Pack)
GN033-SBH
Cup Holder Mount
• Most smartphones, mobile phones, and cell phones
having heights between 80mm and 138mm tall
• Apple iPhone - All models
• RIM BlackBerry - All non-ip models
• HTC Phones - All non-ip models
• Motorola Phones - All non-ip models
• Nokia Mobile Phones - All non-ip models
• Palm - All non-ip models
• LG Mobile Phones - All non-ip models
• Samsung - All non-ip models
• Sony Ericsson - All non-ip models
• Sanyo - All non-ip models
• Pantech - All non-ip models
• Google - All non-ip models
No tools required for installation.
Note: mount may not work with adjustable, “pop out” cup holders or oversize
cup holder openings found in full-size pickup trucks.
Do not place mount in or near an air bag deployment zone or where it
!
will obstruct view of the road.
All brand n ames and produc t names are tradem arks or registe red trademark s of their respec tive owners.
Install the Support Legs to the Holder
Step 1.
Insert the holder support legs (A) by sliding them into the
support leg grooves (B) on the top and bottom of the holder.
B
(A) Cup Holder
A
A
Neck
A
O N
CLOSE
A
B
(B) Cup Holder Base
iPhone Holder Attachment
Step 1.
Step 2.
Adjust the angle of the dual T head by tightening the adjustment
nut at the top of the cup holder shaft (A).
Install the iPhone holder to the shaft by inserting the dual T-tabs
(B) on the shaft into the T-slots (C) on on the back of the holder.
(B) Cup Holder
(A) Angle
Shaft T-tabs
Adjustment
Nut
(D) Optional
support
pads
Safety Precautions
!
Do not install Arkon products over an air bag cover or within the air
OPEN
CLOSE
bag deployment zone. Arkon Resources, Inc. assumes no responsibility of liability for injury or death as a result of car crashes and / or
air bag deployment.
Arkon is not responsible for any damages caused to your car, your
device, or yourself due to the installation or use of this pedestal mount.
The Mobile Mounting Specialists™
Consumer Hotline:
USA (800) 841-0884
INT’L (626) 254-9005
Monday - Friday 9 am - 5 pm, PST
(C) T-slots
www.arkon.com
Arcadia, CA 91006 USA
Designed in USA | Made in Taiwan & China
© Copyright 2010 Arkon Resources, Inc.
SM523-G
|
Cup Holder Mount with Flexible Goosneck Shaft with Slim-Grip™ for Smartphones
Insert Phone into Holder
Step 1.
Adjusting Holder to Fit Phone
Step 1.
Secure holder with your hand for support, as spring-loaded
mechanism requires signicant force to operate. Hold your
phone and insert into universal holder by pushing down on the
bottom spring-loaded support legs with moderate amount of
pressure (D). Slide the top of the device under the top support
legs (E) until it ts snuggly in the holder.
If necessary, adjust the support legs (F) on top and bottom by
sliding them laterally to avoid any buttons or ports that may be
on your phone.
Fitting for Larger Phones
For larger phones such as the T-Mobile G2 and Motorola Droid X,
install the two included extra long support legs
Step 1.
E
Insert the extra long support legs (A) by sliding them into the
support leg grooves (B) on the top and bottom of the holder.
A
D
(iPhone device
not included)
B
A
Insert Phone into Holder
Step 1.
F
Secure holder with your hand for support, as spring-loaded
mechanism requires signicant force to operate. Hold your
phone and insert into universal holder by pushing down on the
bottom spring-loaded support legs with moderate amount of
pressure (C). Slide the top of the device under the top support
legs (D) until it ts snuggly in the holder.
F
Safety Precautions
!
Do not install Arkon products over an air bag cover or within the air
bag deployment zone. Arkon Resources, Inc. assumes no responsibility of liability for injury or death as a result of car crashes and / or
air bag deployment.
Arkon is not responsible for any damages caused to your car, your
device, or yourself due to the installation or use of this pedestal mount.
The Mobile Mounting Specialists™
Consumer Hotline:
USA (800) 841-0884
INT’L (626) 254-9005
Monday - Friday 9 am - 5 pm, PST
D
www.arkon.com
Arcadia, CA 91006 USA
Designed in USA | Made in Taiwan & China
© Copyright 2010 Arkon Resources, Inc.
Loading...