Arkon IPM525-S User Manual
IPM525-S | Flexible Gooseneck Seat Bolt or Floor Mount for Apple iPhone® and iPod touch®
CM088-TS-2
15” Flexible Floor Mount
SP-CM088-SBH
360º Swivel SBH Head
(opti onal)
Passenger Seat Bolt Mounting
1
SM050-2
Slim-Grip™ Holder for
iPhone & iPod touch
For a simple mount that can be easily moved to another vehicle, install
using the passenger seat track bolt.
Do not place mount in or near an air bag deployment zone or
!
where it will obstruct view of the road.
Step 1.
Step 2.
Screw the fl exible steel shaft into the seat track bolt bracket.
With a socket wrench, loosen the passenger seat track bolt, insert the seat track bolt bracket, and retighten the seat track bolt.
Package Contents:
(1) CM088-TS-2 - 15” Flexible steel gooseneck fl oor or console mount
Includes: (1) Seat Bolt Bracket, (1) Floor / Console Bracket, (4)Screws,
(4) Plastic Caps, and (1) Flexible Steel Shaft with Plastic Tubing
(1) SM050-2 - Slim-Grip™ holder for Apple iPhone and iPod touch®
(1) SP-CM088-SBH - 360º Swivel SBH Head (optional)
Compatible with the following devices:
Apple iPhone® 4•
Apple iPhone® 3GS•
Apple iPhone® 3G•
Apple iPhone® Original•
Apple iPod touch® - All models•
Do not place mount in or near an air bag deployment zone or where it
!
will obstruct view of the road.
*Appl e®, iPhone®, and iPod to uch® are tr ademar ks of App le Compu ter, Inc. Ar kon Resou rces, In c. is not affi li ated wit h Apple Co mputer, In c.
Step 1.
Step 2.
Position the Floor/Console Bracket and drill into the fl oor or console.
Attach the Floor / Console Bracket with screws and cover with
plastic caps.
Step 3.
Screw the steel shaft into the Floor / Console Bracket.
Console Mount
2
Floor or Console Mounting
For a more permanent mount, connect the Floor / Console Mount Bracket
to the fl oor or console. This will require drilling into your vehicle’s
interior surface.
Drilling into the dash, fl oor, or console will permanently damage
!
the vehicle. Use caution and consult a mobile install professional
to avoid drilling into the gas tank, electrical system or other highly
sensitive vehicle components.
Safety Precautions
!
Do not install Arkon products over an air bag cover or within the air
bag deployment zone. Arkon Resources, Inc. assumes no responsibility of liability for injury or death as a result of car crashes and / or
air bag deployment.
Arkon is not responsible for any damages caused to your car, your
device, or yourself due to the installation or use of this pedestal mount.
3
Pedestal Head Adjustments
Step 1.
Adjust the steel shaft by bending with both hands to the
desired location of the male dual T head.
Step 2.
Use the adjustment knob and wing nut on the pedestal head to
swivel or rotate the head position if necessary.
Consumer Hotline:
USA (800) 841-0884
INT’L (626) 254-9005
Monday - Frid ay 9 am - 5 pm, PST
Floor Mount
Continued on other side...
The Mobile Mounting Specialists™
www.arkon.com
Arcadia, CA 91006 USA
Designed in USA | Made in China and Taiwan
© Copyright 2010 Arkon Resources, Inc.
IPM525-S | Flexible Gooseneck Seat Bolt or Floor Mount for Apple iPhone® and iPod touch®
Install the Support Legs to the Holder
Step 1.
Insert the holder support legs (A) by sliding them into the
support leg grooves (B) on the top and bottom of the holder.
B
A
A
B
A
A
iPhone Holder Attachment
Step 1. Connect the dual T-slots (C) on the back of the holder to the
dual T-tabs (D) on the mount pedestal head.
(D) T-tabs
(C) T-slots
Adjusting Holder to Fit Phone
Step 1.
If necessary, adjust the support legs (G) on top and bottom by
sliding them laterally to avoid any buttons or ports that may be
on your phone.
G
G
Using the Optional 360° Swivel SBH Head for Landscape Viewing
Step 1.
To rotate your device in landscape view, install the optional
SP-CM088-SBH 360° swivel SBH head. Unscrew the wing
nut on the gooseneck and remove the already installed tilt
swivel head. Insert the SP-CM088-SBH 360° swivel SBH head
and retighten the gooseneck wing nut. Adjust the angle of
the 360° swivel SBH head with the head wing nut and swivel
adjustment ring as necessary.
Insert Phone into Holder
Step 1.
Secure holder with your hand for support, as spring-loaded
mechanism requires signifi cant force to operate. Hold your
phone and insert into universal holder by pushing down on the
bottom spring-loaded support legs with moderate amount of
pressure (E). Slide the top of the device under the top support
legs (F) until it fi ts snuggly in the holder.
F
E
Safety Precautions
!
Do not install Arkon products over an air bag cover or within the air
bag deployment zone. Arkon Resources, Inc. assumes no responsibility of liability for injury or death as a result of car crashes and / or
air bag deployment.
Arkon is not responsible for any damages caused to your car, your
device, or yourself due to the installation or use of this pedestal mount.
(iPhone device
not included)
Swivel
Adjustment
Ring
Wing Nut
The Mobile Mounting Specialists™
Consumer Hotline:
USA (800) 841-0884
INT’L (626) 254-9005
Monday - Frid ay 9 am - 5 pm, PST
Wing Nut
www.arkon.com
Arcadia, CA 91006 USA
Designed in USA | Made in China and Taiwan
© Copyright 2010 Arkon Resources, Inc.
Loading...