Arizona Industries Field Assembling

TABLE OPERATING FIELD

NSN: 6530-01-321-5592

ASSEMBLY and PACKING

INSTRUCTIONS

INTRODUCTION

The field operating table is manufactured by Arizona Industries for the blind at 3013 W
Lincoln street Phoenix, AZ 85009-5699 Phone: [phone] FAX: [phone],
the current cost for the unit is $5,500.00 it is an AAC-L item and carries a LIN: T00578.

The field operating table is a portable type that is quickly assembled and is used for
surgical procedures in the far forward operations, the table contains 2 adjustable 100 watt
halogen surgical lights, there is no patient transfer required, patient remains on a litter
that rests on the top of two rail assemblies.

The components are easily detached as needed from the table, the table measures 53
inches in length, 26 inches wide and 25 to 33 inches working height when assembled, the
unit weight when unpacked from the container is 80 pounds, also the table is capable of
using all military litters.

COMPONENT LIST

The OR table is issued with the following items:

QTY ITEM DESCRIPTION NSN

2 Right corner leg assemblies 6530-01-455-7585
2 Left corner leg assemblies 6530-01-455-7387
8 Extrusion bars 6530-01-455-7634
4 Rail assemblies 6530-01-455-7638
2 Mesh shelf assemblies 6530-01-453-9076
1 Vinyl drain pad 6530-01453-7698
2 Litter rails 6530-01-455-7642
1 Bag frame 6530-01-455-7646
1 Weld tray assembly 6530-010455-7653
2 Clamp assemblies 6530-01-455-7657
1 Tray clamp assembly 6530-01-455-7907
1 Support posts 6530-01-455-7662
1 Tray post 6530-01-455-7685
1 Guide weldment 6530-01-455-7690
2 Armboard assemblies 6530-01-453-7696
1 Tray-stand assembly 6530-01-455-7692
1 Tray instrument 6530-00-793-9570
2 Arm assemblies 6530-01-455-7695
3 IV poles 6530-01-455-7860
2 Strap assemblies 6530-01-455-7865
2 Halogen Lamp assemblies (surgical lights) 6240-01-455-7873
2 Wrenches for adjustment of the surgical lights 5120-01-455-7901
3 Lights (spare bulbs) 6240-01-463-7057
1 Reusable container 6530-01-432-3173

The step by step instructions are provided to assist in assembly, part identification, and
repackaging of the table back into the reusable storage container. To prepare the table for
assembly do the following:

1. Open the storage container and remove the top tray and center tray from the
container.

2. Complete an inventory of the Operating Table components.

3. Remove all of the components from the storage container.

4. During the removal of the Operating Table components inspect each item for damage.

5. When removing the Surgical Light assemblies use caution not to lay them where they
could accidentally be knocked off and get damaged.

(NOTE)

Be very careful when handling the Surgical Lights if dropped there is a possibility that
the circuit board in the arm assembly could get damaged.

The circuit board is located in the arm assembly of the surgical light.

JT 101 Circuit Board

To assemble and set up the operating table follow the instructions beginning on the next
page.

ASSEMBLY INSTRUCTIONS

Step 1: Obtain the 4 OR table legs.

Step 2: Obtain 4 of the short connecting rails.

Step 3: Attach the 4 short connecting rails to the end side of the table legs.

Step 4: Obtain the 4 remaining short connecting rails and the 4 long connecting rails.

Step 5: Connect the 4 long and the 4 short connecting rails together making 4 single long

connecting rails.

Step 6: Attach the lower mesh shelf to the lower connecting rails.

Step 7: Attach the upper and lower connecting rails to the legs one end at a time.

Step 8: Attach the connecting bars to the remaining legs and the lower mesh shelf Velcro on each

end of the OR table.

Step 9: Attach the drain pad to the upper connecting bars of the OR table.

Step 10: Attach the stretcher rails to the OR table.

Step 11: Attach the 2 clamps to the OR table side connecting bar.

Step 12: Obtain the 2 silver support posts and place into the 2 clamps.

Step 13: Obtain the arm board assemblies and place onto the support posts.

**Upon completion of steps 11, 12, and 13 the OR table should appear as below.

Step 14: Obtain the tray clamp assembly and attach to the OR table upper rail on the opposite

end of the arm boards.

Step 15: Obtain the tray post and insert into the clamp.

Setp16: Obtain the tray stand assembly and position onto the tray post.

Step 17: Obtain the tray and place on top of the tray stand assembly.

**The OR table should appear as below at this point of assembly.

Step 18: Obtain the two arm assemblies and place into the end OR table upper legs.

Step 19: Obtain the IV poles and insert into the arm assembly.

Step 20: Obtain the surgical lights and insert into the arm assembly

**At this point the OR table should appear as below.

Step 21: Obtain the bag frame assembly and attach to the end of the OR table.

Step 22: Obtain the tray assembly and insert onto the OR table end.

**This completes the OR table set up. the OR table should appear as below.

COMPONENT DESCRIPTIONS

Corner (R) Assembly

2 each, Part Number 40212

NSN: 6530-01-455-7585

Corner (L) Assembly

2 each, Part Number 40213

NSN: 6530-01-455-7387

23.62 Extrusion

8 each, Part Number: 30373

NSN:6530-01-455-7634

Shelf

2 each, Part Number: 60157

NSN: 6530-01-453-9076

4 each, Part Number: 40217

Rail Assembly

NSN: 6530-01-455-7638

Rail Assembly

2 each, Part Number: 30381

NSN: 6530-01-455-7642

Bag Frame

1 each, Part Number: 30393

NSN: 6530-01-455-7646

Tray Assembly (weld)

1 each, part Number: 30392

NSN: 6530-01-455-7653

Clamp assembly

2 each, Part Number: 40220

NSN:6530-01-455-7657

Support Post

2 each, Part Number: 30354

NSN: 6530-01-455-7662

Tray Clamp Assembly

1 each, Part Number: 40221

NSN:6530-01-455-7907

Tray Post

1 each, Part Number: 30391

NSN: 6530-01-455-7685

Guide Weldment

1 each, Part Number: 30388

NSN: 6530-01-455-7690

Armboard Assembly

2 each, Part Number: 40218

NSN: 6530-01-453-7696

Tray Stand Assembly

1 each, Part Number: 40219

NSN: 6530-01-455-7692

Arm Assembly

2 each, Part Number: 30379

NSN: 6530-01-455-7695

Tray Instrument

1 each, Part Number: 9570

NSN: 6530-00-793-9570

IV Pole

3 each, Part Number: 40222

NSN: 6530-01-455-7860

Strap

2 each, Part Number: 30394

NSN: 6530-01-455-7865

2 each, Part Number: 64450AX

Halogen Lamps

NSN: 6240-01-455-7873

Wrench

2 each, Part Number: 20404

NSN:5120-01-455-7901

Drain Pad

1 each, Part Number: 60167

NSN: 6530-01453-7698

2 each, Part number: 75W/12V-GY6.35

NSN: 6240-01-463-7057

Lamp Bulb

The Storage Container NSN: 6530-01-432-3173

The table when disassembled stores into a reusable carrying container that weighs
approximately 200 pounds when packed. The cost of the storage container is $1098.00.

STORAGE CONTAINER

TOP TRAY

CENTER TRAY

BOTTOM BASE CUSHION

The container has custom made inserts to cushion the components and accessories of the
operating table and should not be removed.

NOTE

(This is a Custom made Storage Container for the storage of the operating table only).

DISASSEMBLY AND REPACKING INSTRUCTIONS

To disassemble the operating table reverse the order in which the table was assembled. Again,
exercise care to ensure that fragile components are not damaged as the table is disassembled. Before
inserting the components of the table back into the case make sure that each component is thoroughly
cleaned.

Note that the case is manufactured with trays each having inserts for each component of the table built
directly into them. By replacing the components into the proper insert each will be protected during
transport. Beginning on the next page are illustrations of each tray indicating exactly where each
component is to be inserted so that maximum protection for each item is provided.

TOP TRAY LAYOUT

Item No. Description

1 Bulbs
2

1

Shelf
3 Rail Assembly
4 Armboard Assembly
5 Lights, Reynolds Mach and Tool , Melrose, IL 60160

1

Note that item #2 is in the tray insert beneath item #4

CENTER TRAY LAYOUT

Item No. Description

1 Arm Assembly
2 Tray Assembly
3 Bag Frame Assembly
4 20.62 Extrusion
5

1

Support Post
6 Clamp Assembly
7 Wrench
8 Guide Weldment
9 Rail
10 Clamp Assembly
11 Tray Post
12 Straps
A A clamp fits into each insert marked with an “A”

1

Note that items 5 and 11 fit into the same insert

BOTTOM CUSHION INSERT LAYOUT

1 Corner Assembly, Right Side
2 Corner Assembly, Left side
3 I.V. Poles, 3 each
4 Tray Clamp Assembly
5 Tray Stand Assembly
6 Tray, NSN 6530-00-793-9570

Item No. Description