Aries Filterworks AF-10-3690, AF-10-3690-BB, AF-20-3690, AF-20-3690-BB Data Sheet

KEY FEATURES

•

USE OF RESINTECH® PREMIUM HIGH CAPACITY SIR-900 MEDIA

•

EFFECTIVE OVER A WIDE pH RANGES

•

SUPERIOR PHYSICAL STABILITY AND LOWER PRESSURE DROP

FLUORIDE REMOVAL CARTRIDGES

LABORATORY • COMMERCIAL • RESIDENTIAL

AF SERIES

FLUORIDE REMOVAL

Fluoride removal is achieved by utilizing the advanced media technology of
ResinTech

®

SIR-900 media. AF Series cartridges remove Fluoride by a chemical
reaction with the media. ResinTech® SIR-900 is a synthetic aluminum oxide that
is specially processed to have minimum fines and other foreign matter. It has
minimal shrinkage /swelling and low-pressure loss. The product is physically
stable and can be used over a wide pH range.

APPLICATIONS

DRINKING WATER -

Consumers, who are concerned about fluoride in the municipal water supply
for health reasons and require its removal, can benefit by the use of a fluoride
removal cartridge at the Point of Use (POU).

PRIVATE WELLS -

Some areas of the country have high levels of naturally occurring fluoride. Wells
Supply 15% of American populations with drinking water, and these wells are
not subject to EPA regulations. These wells provide safe clean water, but occa­sionally can become contaminated, resulting in illness.

COMPONENT

ABOUT FLUORIDE

Fluoride can occur in drinking water naturally as a result of the geological composition of soils and bedrock. Most water supplies contain some natu­rally occurring fluoride. Fluoride also enters drinking water in discharge from fertilizer or aluminum factories. The decision to fluoridate a water supply
is made by the State or local municipality. EPA has set the level of protection for fluoride at 4.0 mg/L or 4.0 ppm, to prevent potential health risk.

Exposures to fluoride have increased since the early 1960s. At that time, drinking water and food and beverages prepared with fluoridated water
accounted for nearly an individual’s entire fluoride intake. Today, exposure to fluoride comes from fluoridated dental products, as well as the voluntary
addition of fluoride to drinking water.

FEATURES & BENEFITS

• USE OF RESINTECH

®

PREMIUM HIGH CAPACITY SIR-900 RESIN

Extended surface area and pore distribution gives the media highest possible operating capacity and lowest leakage. For best performance,
lower pH water sources are preferred

• FDA DRINKING WATER APPROVED MATERIALS OF CONSTRUCTION

Sonic welded construction is a solvent free method to join and assemble plastic parts, producing the highest quality safest product

• FITS STANDARD RESIDENTIAL AND INDUSTRIAL SIZE HOUSING

AF Series cartridges are double-open end cartridges that fit standard residential and industrial housings

• OVERSIZED CARTRIDGE FOR MAXIMUM MEDIA FILL

AF Series cartridges have up to 50% higher capacity and extend cartridge life, due to the use of larger cartridges

• QUALITY PRODUCED AND MADE IN THE USA

Cartridges are produced by Aries FilterWorks, a division of ResinTech®. Strict quality control over all aspects of cartridge and media production
allows complete traceability of every filter

160 Cooper Road • Building #2, Suite A • West Berlin, NJ 08091-9243, USA • p: 856.626.1550 • f: 856.626.1551 • [e-mail] • ariesfilterworks.com

A Division of ResinTech • Innovations in Ion Exchange

AF SERIES - FLUORIDE REMOVAL

4.5

1

2

4

TECHNICAL DATA

10” SLIM 20” SLIM 10” SUPER BLUE 20” SUPER BLUE

Diameter (in.) 3.0” 2.9” 4.6” 4.6”
Length (in.) 9.9” 20.0” 10.0” 20.0”

3

Temperature (˚F.)
Min. 40˚ 40˚ 40˚ 40˚
Max 100˚ 100˚ 100˚ 100˚

Pressure (psi)
Min. 20 20 20 20
Max. 125 125 125 125

Micron Rating (µ) 25 25 25 25
Materials of Construction

1. Gasket TPE TPE TPE TPE

2. End Caps PP ABS ABS ABS

3. Pads PE PE PE PE

4. Body / Tube PP ABS ABS ABS

5. Media*

PP Polypropylene
ABS Acrylonitrile Butadiene Styrene

ResinTech

®

Premium SIR-900 Synthetic Adsorbent

PE Polyester
TPE Thermoplastic Elastomer

FLUORIDE DELTA P

5

4.0

3.5

3.0

2.5

2.0

1.5

Delta P (psi)

1.0

0.5

0

00.1 0.2

Flow (gpm)

0.30.4 0.5

10” Slim Line

20” Slim Line

10” Super Blue

20” Super Blue

MEDIA

As a division of ResinTech, Inc.®, Aries FilterWorks is the only integrated water filtration media and
cartridge manufacturer providing a premium product at the most competitive cost. Aries builds
technology and knowledge of ion exchange and specialty adsorbents into each cartridge. Strict
quality control over all aspects of cartridge production allows complete traceability of every filter.

3

ORDERING GUIDE

2

MEDIAPART NUMBER STANDARD HOUSING

DIAMETER X LENGTH

SERVICE FLOW

RATE (GPM)

AF-10-3690 2.5” x 10” 0.1 475
AF-20-3690 2.5” x 20” .20 1,100
AF-10-3690-BB 4.5” x 10” .20 1,200

ResinTech® Premium

SIR-900 Synthetic

Adsorbent

AF-20-3690-BB 4.5” x 20” 0.2 2,500

COMPONENT

Filter cartridge Certified to

NSF/ANSI Standard 42 and

NSF/ANSI Standard 61

for material requirement(s) only.

Filter cartridge Certified to

NSF/ANSI Standard 372
for low lead compliance.

Notes: Ordering information subject to change without notice. Please verify all specifications prior to ordering.

To place an order call [phone] or e-mail [e-mail]

The following is made in lieu of all other warranties expressed or implied. Manufacturer’s and Seller’s only obligation shall be to issue credit against the purchase or replacement of the equipment proved to be defective in material or workmanship. Neither Manufacturer nor Seller
shall be liable for any injury, loss or damage, direct or indirect, special or consequential, arising out of the use of, misuse, or the inability to use such product. The information contained herein is based on technical data and tests which we believe to be reliable and is intended for
use by persons having technical skill at their discretion and risk. Since conditions of use are outside ResinTech’s control, we can assume no liability whatsoever for results obtained or damages incurred through the application of the data presented. This information is not intended
as a license to operate under, or a recommendation to infringe upon, any patent of ResinTech’s or others covering any material or use. The foregoing may not be altered except by written agreement signed by officers of the manufacturer.

IMPORTANT NOTICE TO USER:

DS-AFFluoride-rev1.5

CAPACITY

(GALLONS)