Aries Automotive S221007-2 User Manual
(6) 10mm Nut Plates
INSTALLATION INSTRUCTIONS
r
r
PARTS LIST:
Description Qty Description
Qty
1 Driver
1 Passenger/
1 Driver
1 Passenger/
1 Driver
1 Passenger/
1 Driver
1 Passenger/ Rear Mo
6 10mm Nut Plates 12 6mm x 25mm Button Head
12 10mm x 30mm Hex Bolt 24
1 4mm Allen wrench
/Left Side Bar 4 10mm x 25mm Hex Bolt
Right Side Bar 4 10mm ID x 30mm OD Flat Washer
/Left Front Mounting Bracket 12 10mm ID x 23mm OD Flat Washer
Right Front Mounting Bracket 16 10mm Lock Washer
/Left Middle Mounting Bracket 8mm x 35mm Hex Bolt
Middle Mounting Brace Bracket 8mm ID x 24mm OD Flat Washer
/Left Rear Mounting Bracket 8mm Lock Washer
2007-12 JK WRANGLER 4DR & JK 8 TRUCK
(will not fit with factory rocker)
Part # S221007 / S221007-2
unting Bracket 12 6mm Lock Nuts
6
6
6
6mm ID x 18mm OD Flat Washers
senger/Right
Pas
Side ba
Front
Driv
er/Left side
Side ba
Passenger Side Rear
Mounting Bracket (short)
Driver Side Rear Mounting
Bracket (short)
Cap Bolts
Passenger Side
Center (long)
Mounting
Bracket
Passenger Side Front (mid
length) Mounting Bracket
Page 1 of
Driver Side
Center (long)
Mounting
4
Driver Side Front (mid
length) Mounting Bracket
Bracket
Fig 3B Fig 3D
3/8"3/
9 3/8"
Fig 3C
10 1/8"
10 1/8"
8 3/4"
8 3/4"
Passenger side "mid-length"
front Bracket pictured
(Fig 3A) Passenger side "long"
center Bracket pictured
Passenger side "short" rear
Bracket pictured
PROCEDURE:
1. REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. READ INSTRUCTIONS
CAREFULLY BEFORE STARTING INSTALLATION. FACTORY INSTALLED OR AFTERMARKET
"ROCK RAILS," SIDE STEPS OR RUNNING BOARDS MUST BE REMOVED.
2. Start installation toward the front of the passenger side of the vehicle. Determine if the vehicle has an
open floor panel or a threaded hole in the floor panel for the top tab on the Bracket, 1 - 2).
(Fig
Remove any insulation that may be covering the mounting locations.
3. Select the passenger side front Bracket. VERY IMPORTANT: The 6 Mounting Brackets look very
similar. Use the instructions to properly identify the front, center and rear Brackets for either side of the
vehicle. Each bracket has been designed for a specific location for proper installation.
a. Vehicles with open mounting location: Insert (1) 10mm Nut Plate into the large square
opening in the floor panel. Line up the threaded nut with the small hole in line with the tab on the
Bracket, 1). Bolt the Bracket to the Nut Plate with (1) 10mm x 35mm Hex Bolt, (1)
10mm Lock Washer and (1) 10mm Flat Washer, 3A). Do not tighten hardware.
(Fig
(Fig
b. Vehicles with factory threaded hole in floor panel: Bolt the tab on the Bracket to the
threaded hole in the floor panel with (1) 8mm x 35mm Hex Bolt, (1) 8mm Lock Washer and (1)
x 24mm OD Large Flat
8mm Washer, 2 & 3A). Do not tighten hardware.
(Fig
4. Line up the mounting plate on the Bracket with the (2) factory holes in the pinch weld. Bolt the Mounting
Bracket to the back of the pinch weld using the included (2) 6mm x 25mm Button Head Allen Bolts, (2)
6mm Flat Washers, ( Flat Washers ,
(inside against the bracket), and (2) 6mm Nylon Lock Nuts, 3A). Leave loose at this time.
against pinch weld), (2) 6mm x 18mm ODx 18mm
(Fig
5. Repeat Steps 2 – 4 for Center and Rear Mounting Bracket installation. Use the instructions to correctly
identify the Brackets, 3B, 3C, 3D & 4).
(Fig
6. Once all three Mounting Brackets are securely in position, place the passenger Sidebar onto the
Mounting Brackets and secure it with the included ( ,(6) mm Lock Washers
and (6) mm Flat Washers, . NOTE: Mounting cradles on Brackets should be inline and
(Fig 5)10
6)
10,(10mm x 30mm Hex Bolts
pointing toward the rear of the vehicle for proper installation. Snug all hardware but do not tighten at
this time.
7. Adjust and level the Sidebar and tighten all hardware.
8. Repeat Steps 2 - 7 for /left Sidebar installation.
Driver
9. Do periodic inspections to the installation to make sure that all hardware is secure and tight.
To protect your investment, wax this product after installing. Regular waxing is recommended to add a protective layer
over the finish. Do not use any type of polish or wax that may contain abrasives that could damage the finish.
For stainless steel: Aluminum polish may be used to polish small scratches and scuffs on the finish. Mild soap may be
used also to clean the Sidebar.
For gloss black finishes: Mild soap may be used to clean Sidebar.
2
4Page of
Loading...