
10-1.50mm x 30mm Hex Bolts
Driver/Left Mounting Bracket
10mm x 27mm OD x 3mm Flat Washers
Passenger/Right Mounting Bracket
Passenger/Right Top Bracket
8-1.25mm x 25mm Button Head Allen Bolts
Driver/Left Top Inner Support Bracket
8-1.25mm x 30mm Hex Bolts
Passenger/Right Top Inner Support Bracket
8mm x 16mm OD x 1.6mm Flat Washers
Top Support Rear Backing Plates
12-1.75mm x 30mm Double Bolt Plates
12-1.75mm x 35mm Single Bolt Plates
12mm x 24mm OD x 2.5mm Flat Washers
6mm x 18mm OD x 1.6mm Flat Washers
Driver/Left
Mounting Bracket
(2) Frame Mounting
Driver/Left
Passenger/Right
Top Bracket
(2) 12mm x 35mm
Single Bolt Plates
Passenger/Right
Inner Top Bracket
(2) 12mm x 30mm
Double Bolt Plates
Passenger/Right
Mounting Bracket
Driver/Left Inner
Top Bracket
(2) Top Support
Backing Plates
INSTALLATION I N ST R UCTIONS
PARTS LIST:
2014 SILVERADO 1500
PART # P4083
Brackets

PROCEDURE:
1. REMOVE CONTENTS FROM BOX AND VERIFY ALL PARTS ARE PRESENT. READ
INSTRUCTIONS CAREFULLY. DO NO T ATTEM PT INS TALLATION ALONE; PERSONAL INJURY
OR DAMAGE TO THE VEHICLE MAY RESULT. CUTTING MAY BE REQUIRED. ASSISTANCE IS
HIGHLY RECOMMENDED.
2. Start by Selecting your LED light (Sold Separately) mounting hardware & brackets, you will need to
first attached the hardware to the support flange, (Example of LED light attached Fig 1) NOTE: if you
have your own LED light, LED Manufactures will have similar but different mounting styles or
brackets, once you determine you mounting options attach it to the support flange as seen in
(Fig1)
3. With the LED light attached to the support flange select the (2) 8mm nut clips place each nut clip into
the slotted holes on either side of the support flange, as seen in (Fig 2) with the support flange prepare
you will need to lay the grill guard face down to install the support flange NOTE: (it is recommended to
lay out some of the cardboard your grill guard came in or a blanket to protect the grill guard finish).
place the grill guard face down with this done place the support flange with the LED attached into the
Center flange attach each side of the support flange to the inner brackets inside the center flange of the
grill guard with (2) 8mm hex bolts, (2) 8mm flat washers, & (2) 8mm lock washers as seen in (Fig 3)
Snug but do not tighten at this time.
4. Start installation from under the front of the vehicle. Determine if the vehicle is equipped with tow
hooks.
Tow Hook equipped vehicles:
a. Remove the factory tow hook from the end of each frame channel, (Fig 4). NOTE: The driver
side tow hook removal and the reinstallation of both tow hooks with the Grille Guard is difficult
and assistance is highly recommended.
i. Option 1: Remove the hex bolts securing the driver side of the bumpe r to the bracket.
Use a short pry bar or large screwdriver to move the tab on the bumper bracket up and
away to clear the hex bolt and slide it out past the bumper bracket, (Figs 5A, 5B & 8).
ii. Option 2: Remove plastic radiator grille. Loosen and/or completely remove the front
bumper to remove the long hex bolt in the driver side tow hook, (Fig 5B).
b. Reattach the bumper after the tow hooks have been removed and the openings have been
checked for Bracket clearance, (Fig 8). Leave factory hardware loose at this time.
c. Next, select (1) Frame Bracket and the driver side Mounting Bracket, (Fig 12). Bolt the
Mounting Bracket to the bottom of the Frame Bracket with (3) 8mm x 30mm Hex Bolts, (3) 8mm
Lock Washers and (3) 8mm Flat Washers. Snug but do not fully tighten hardware at this time.
d. Insert the Bracket assembly through the opening in the plastic bumper, (Fig 8). Line up the (3)
holes in the Frame Bracket with the holes in the end of the frame channel.
e. Insert the driver side tow hook back into position in the end of the frame above the Bracket
Assembly, (Fig 13). Reattach the tow hook using only the long factory hex bolt inserted through
the Frame Bracket and tow hook at this time. If tow hooks are not going to be reinstalled, skip
ahead to Step i, "Vehicles without tow hooks" installation instructions.
f. Leave hardware loose at this time.
g. Repeat this Steps c - f to install the passenger side Bracket assembly and tow hook. Once both
Bracket assemblies are installed, skip forward to Step 3.
Page 2 of 9

Vehicles without tow hooks:
a. Cut out the indented area in both sides of the plastic bumper insert to clear the Brackets as
pictured, (Figs 6 & 7). IMPORTANT: Make several small cuts for best fit. Do not cut through the
top edge of the panel. NOTE: The plastic panel is held in place with several small screws. The
screws at the top corners are difficult to impossible to reach and remove without damaging the
cover with the bumper in place. If you prefer to remove the panel to cut out the openings, it may
be necessary or easier to remove the plastic grille then the steel bumper assembly with the
plastic panel attached to access all of the small screws and clips.
b. Reattach the bumper and/or bumper insert, (if removed), and grille once openings have been
cut out and checked for clearance, (Fig 8). Tighten all factory bumper hardware at this time.
h. Select (1) Frame Bracket, (Fig 9). Insert the Bracket through the opening in the plastic bumper,
(Fig 8). Line up the (3) holes in the Bracket with the holes in the end of the frame channel.
i. Select (1) 12mm Double Bolt Plate, (Fig 10A). Insert the Bolt Plate into the end of the frame
channel, through the (2) holes in the side of the frame and out through the Bracket. Secure the
Bolt Plate to the Bracket with (2) 12mm Flat Washers, (2) 12mm Lock Washers and (2) 12mm
Hex Nuts, (Fig 10B). Snug but do not fully tighten hardware at this time. Repeat this Step to
install the 12mm x 35mm Single Bolt Plate, (Fig 11A), into the remaining hole in the other side
of the frame channel and Bracket, (Figs 11B & 11C).
j. Next, select the driver side Mounting Bracket. Bolt the Mounting Bracket to the bottom of the
Frame Bracket with (3) 8mm x 30mm Hex Bolts, (3) 8mm Lock Washers and (3) 8mm Flat
Washers, (Figs 12 & 13). Do not tighten hardware at this time.
k. Repeat Steps h - j to install the passenger side Frame and Mounting Brackets.
5. With assistance, hold the Grille Guard up in position on the outside of the Mounting Brackets. Bolt the
Grille Guard to the Brackets with (4) 10mm x 30mm Hex Bolts, (8) 10mm Flat Washers, (4) 10mm Lock
Washers and (4) 10mm Hex Nuts, (Fig 13). Snug but do not tighten hardware at this time.
6. Check the Grille guard side to side alignment with the vehicle. Adjust as required then tighten only the
(6) 8mm Hex Bolts securing the Mounting Brackets to the bottom of the Frame Brackets.
a. Vehicles with tow hooks: Once adjusted side to side and after the 8mm hardware is tightened,
insert the short factory tow hook bolt, (one per tow hook), through the remaining hole in the
Frame Bracket and back into the tow hook. Repeat to reinstall the passenger side tow hook bolt.
7. Tighten all tow hook and/or Frame Mounting Bracket hardware at this time. Do not fully tighten the
Grille Guard to Bracket hardware at this time.
8. Next, open the hood and remove the plastic cover between the top of the grille and the radiator, (Fig
14). NOTE: Use a small flat head screw driver to pop up the center of the plastic clips.
9. Locate the square tube support braces running up at an angle from the top of the frame channel to the
bottom of the hood release mechanism, (Figs 15B, 17 & 18). Select the driver side Inner Top Bracket
and (1) Backing Plate, (Fig 15A). Hold the Inner Bracket up to the bottom of the brace tube with the
Backing Plate over the top. Bolt the Brackets together around the square tube with (2) 6mm x 25mm
Hex Bolts, (2) 6mm Lock Washers and (2) 6m m Flat Washers, (Fig 15B). Leave loose at this time.
10. Repeat Step 9 for passenger side Inner Top Bracket and (1) Backing Plate, (Figs 15A & 15B).
11. Select the driver side Outer Top Bracket, (Fig 16). Insert the Outer Bracket through the grille and up to
the Inner Top Bracket assembly, (Figs 17 & 18). Slide the Bracket assembly up or down the tube to
match up with the Outer Top Bracket . Bolt the Outer Bracket to the top of the Inner Bracket with (2)
6mm x 25mm Hex Bolts, (2) 6mm Lock Washers and (2) 6mm Flat Washers. Leave hardware loose at
this time.
Page 3 of 9

12. Line up the outer bent end of the Top Bracket with the hole in the Grille Guard upright. Bolt the bent
LED light attached to support flange.
Secure support flange into center flange with
end of the Outer Top Bracket to the upright with (1) 10mm x 25mm Button Head Allen Bolt, (2) 10mm
Flat Washers and (1) 10mm Nylon Lock Nut, (Fig 19).
13. Repeat Steps 8 – 12 for passenger side Top Bracket assembly installation.
14. Level and adjust the Grille Guard and fully tighten all hardware including bumper, bumper bracket and
all Grille Guard Bracket hardware. IMPORTANT: Adjust the position of the Top Brackets so that they
cannot come in contact with the plastic grille, (Fig 19).
15. Reinstall the top plastic cover using the factory hardware.
16. Do periodic inspections to the installation to make sure that all hardware is secure and tight.
To protect your investment, wax this product after installing. Regular waxing is recommended to add a
protective layer over the finish. Do not use any type of polish or wax that may contain abrasives that could
damage the finish.
attached (1) per side
NOTE:
but different mounting styles or brackets,
once you determine you mounting options
attach it to the support flange as seen.
(1) 8mm Hex head bolt
(1) 8mm Flat Washers
(1) 8mm Lock washer
LED Manufactures will have similar
Page 4 of 9

Driver Side Mounting Bra cket Installation Pict u red
(Fig 4) Opening for tow hook pictured
(Fig 5A) Driver side pictured from behind bumper
Remove the bolts securing the driver side of
tow hook out of the end of the frame
(Fig 5B) Driver side illustrated from behind bumper to show bumper bolt locations
Page 5 of 9
the bumper to the bumper bracket. Use a large
screwdriver or pry bar to move the mounting
tab up enough to get the long bolt through the

(Fig 6) "No tow hook" model pictured
(Fig 8) Driver side pictured without plastic
panel for instruction purposes only
Mounting holes in end
of frame for tow hook
(Fig 7) Driver side cut out
illustrated for reference only
Driver Side Mounting Bra cket Installation Pict u red
Page 6 of 9
(2) 12mm Flat Washers
(2) 12mm Lock Washers
(2) 12mm Hex Nuts

(Fig 12) Driver side Mounting
Brackets pictured
(Fig 11B) Driver side Bracket installation pictured
(Fig 11C) Driver side Bracket
installation pictured from front
Driver Side Installation Pictured
Page 7 of 9
12mm Flat Washer
12mm Lock Washer
12mm Hex Nut
Bracket to the bottom of
the Frame Bracket with:
(3) 8mm 30mm Hex Bolts
(3) 8mm Lock Washers

(Fig 14) Remove plastic cover on top of grille
(Fig 15A) Passenger side inner Top
Bracket and Backing Plate pictured
Bolt the Top Inner Bracket
(Fig 16) Driver side Top Bracket installation
Page 8 of 9
to the Backing Plate with:
(2) 6mm x 25mm Hex Bolts
(2) 6mm Lock Washers
pictured. Adjust position so that Bracket
cannot come in contact with plastic grille

(Fig 18) Driver side Top Bracket
installation pictured
(Fig 19) Passenger side outer Top Bracket pictured
Bolt the Top Outer Bracket
6mm Lock Washers
6mm Flat Washers
to the Inner Bracket with:
(2) 6mm x 25mm Hex Bolts
(2) 6mm Lock Washers
(2) 8mm Flat Washers
(1) 8mm Nylon Lock Nut
6mm Lock Washers
6mm Flat Washers
Page 9 of 9