Aries Automotive P2062 User Manual

Page 1
1
Grille Guard
4
1
Driver/Left Frame Mounting Bracket
4
1
Passenger/Right Frame Mounting Bracket
4
1
Driver/Left Top Mounting Bracket
4
1
Passenger/Right Top Mounting Bracket
12
1
Driver/Left Top Bracket
6
1
Passenger/Right Top Bracket
2
2
10mm Double Bolt Plates
1
2
10mm Quick Release Bolts
2
2
10mm Special Pivot Washers
2
4
12mm Plastic Washers
2
4
10mm Plastic Washers
2
4
12-1.75mm x 35mm Hex Bolts
(2) 10mm Double Bolt Plates
Driver/Left Side Top
Passenger/Right Side Driver/Left side Frame
Mounting Bracket
Passenger/Right side
10mm Quick Release Bolts Passenger/Right
Driver/Left Side
INSTALLATION I N ST R UCTIONS
PART# P2062
Support Flange
(2) 8mm Nut Clips
PARTS LIST:
Top Mounting Bracket
PROCEDURE:
1. REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. READ INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION. NOT RECOMM ENDED F OR VEHICLES WITH OPTIONAL "ACTIVE" LASER GUIDED CRUISE CONTROL SYSTEMS.

2007-13 TUNDRA 2008-13 SEQUOIA

(Skid plate must be removed if equipped)
Side Top Bracket
Frame Mounting Bracket
Mounting Bracket
Top Bracket
10mm Special Pivot Washer 10mm Flat Washers 10mm Nylon Lock Nut
Page 2
2. Start by Selecting your LED light (Sold Separately) mounting hardware & brackets, you will need to first attached the hardware to the support flange, (Example of LED light attached Fig 1) NOTE: if you have your own LED light, LED Manufactures will have similar but different mounting styles or brackets, once you determine you mounting options attach it to the support flange as seen in (Fig1)
3. With the LED light attached to the support flange select the (2) 8mm nut clips place each nut clip into
the slotted holes on either side of the support flange, as seen in (Fig 2) with the support flange prepare you will need to lay the grill guard face down to install the support flange NOTE: (it is recommended to
lay out some of the cardboard your grill guard came in or a blanket to protect the grill guard finish). place the grill guard face down with this done place the support flange with the LED attached into the Center flange attach each side of the support flange to the inner brackets inside the center flange of the
grill guard with (2) 8mm hex bolts, (2) 8mm flat washers, & (2) 8mm lock washers as seen in (Fig 3)
Snug but do not tighten at this time.
4. WARNING! This Grille Guard is designed to tilt forward by releasing the Quick Release Bolts on the Top Brackets and loosening the upper bolt on the Mounting Bracket when the hood needs to be opened for service. Make sure that all hardware is fully tightened after closing the hood. Read Page 6, "Opening and Closing of Hood," before installing the Grille Guard.
5. Starting from under the front of the vehicle, determine if the vehicle is equipped with small or large tow hooks. Remove the (2) factory tow hooks and set aside, (Figs 4A & 4 B).
6. Select the driver/left Frame Mounting Bracket.
Vehicles with small tow hook: Install the small tow hook over the Mounting Bracket using the factory tow hook hex bolts, (Fig 4A). Vehicles with large tow hooks: Bolt the driver/left side Frame Mounting Bracket to the bottom of the frame with the two factory bolts. NOTE: Large tow hook cannot be reinstalled, (Fig 4B).
7. Repeat the appropriate Step 6 for the passenger side Frame Mounting Bracket installation.
8. Open the hood and locate the two factory holes facing forward on the driver side of the bottom radiator
core support cross member. Insert (1) Double Bolt Plate in from the back of the cross member and out
the front through the (2) holes, (Fig 5).
9. Select the driver side Top Mounting Bracket. Line up the (2) holes in the Top Mounting Bracket with the
previously inserted Double Bolt Plate. Secure the Bracket to the Bolt Plate with (2) 10mm Flat Washers
and (2) 10mm Nylon Lock Nuts, (Figs 6 & 7). Snug but do not tighten hardware at this time.
10. Carefully insert the driver/left Top Bracket through the opening in the bumper and attach it to the tab on
the Top Mounting Bracket with (2) 10mm x 35mm Hex Bolts, (2) 10mm Lock Washers and (2) 10mm
Flat Washers, (Figs 8 & 9). NOTE: Use the included Adhesive Backed Foam Tape to cover any part of the Top Bracket that may come in contact with the vehicle. IMPORTANT: To provide maximum
clearance between the Grille Guard and the vehicle, gently pull the Top Bracket outward away from the
vehicle as you tighten the (2) Hex Bolts, (Fig 10).
11. Repeat Steps 8 - 10 for passenger/right side Top Bracket installation.
12. With assistance, place the Grille Guard face down on a clean surface in front of the vehicle. Position
the mounting tabs on the Grille Guard up to the outside of the driver side Frame Mounting Bracket. Line up the lower hole in the Bracket with the lower hole in the Grille Guard. Insert (1) 12mm Plastic Washer between the Mounting Bracket and the Grille Guard. Line up the Grille Guard, Washer and Bracket and bolt together with the included (1) 12mm x 35mm Hex Bolt, (1) 12mm Lock Washer and (1) 12mm Flat
Washer, (Fig 11).
Page 1 of 7 10/31/2013
Page 3
Fig 1
LED light attached to support flange.
13. Repeat Step 10 to attach the passenger side mounting tab to the Bracket. Snug but do not tighten hardware at this time.
14. Use the (2) previously installed 12mm Hex Bolts to act as a hinge and carefully rotate the Grille Guard
up to the vehicle. Line up the two remaining holes in the Mounting Brackets with the holes in the Grille
Guard and repeat Steps 12 & 13 for installation, (Fig 11). Snug the hardware but do not tighten at this
time.
15. Next, move to the driver side Top Bracket installed in Step 10. Line up the long slot in the Top Bracket with the hole in the Grille Guard upright, (Fig 13). Insert (1) 10mm Plastic Washer between the Top
Bracket and the Grille Guard. Line up the holes in the Grille Guard, Plastic Washer and the slot in the
Top Bracket. Insert (1) 10mm Quick Release Bolt with (1) 10mm Special Pivot Washer, (Fig 13),
through the Grille Guard upright first, the Plastic Washer and through the Top Bracket. Secure the Quick Release Bolt with (1) 10mm Plastic Washer, (to protect the finish on the Top Bracket), (1) 10mm
Flat Washer and (1) 10mm Nylon Lock Nut, (Figs 13 & 14). Snug but do not tighten at this time.
16. Repeat Step 15 to attach the passenger Top Bracket to the Grille Guard.
17. Release/loosen the levers on the Quick Release bolts, (Fig 14), and pull the Grille Guard away from the
vehicle to the "open" position, (Fig 15). Center and level the Grille Guard and tighten all hardware including the Mounting Brackets and Bolt Plates.
18. Adjust the Quick Release Bolt clamping pressure by loosening or tightening the 10mm Nylon Lock Nut. See Steps 23 – 28 for more information.
19. Slowly close the hood and check for clearance. Release both Quick Release bolts. Push the Grille
Guard into the "closed" position. If needed, loosen the upper bolt on each Frame Mounting Bracket,
(Fig 16). WARNING! Do not completely loosen bolts or damage to the truck or Grille Guard may occur.
20. Push the Grille Guard back towards the vehicle and tighten all hardware, (Figs 17 & 18).
21. Do periodic inspections to the installation to make sure that all hardware is secure and tight.
22. For the Led lights wiring please refer to the manufactures installation.
To protect your investment, wax this product after installing. Regular waxing is recommended to add a protective layer over the finish. Do not use any type of polish or wax that may contain abrasives that could damage the finish.
NOTE: but different mounting styles or brackets, once you determine you mounting options attach it to the support flange as seen.
LED Manufactures will have similar
Page 2 of 7 10/31/2013
Page 4
8mm nut clip
Fig 2
Support flange
Secure support flange into center flange with
Per side.
Fig 3
Led Light
attached (1) per side
(1) 8mm Hex head bolt (1) 8mm Flat Washers (1) 8mm Lock washer
Page 3 of 7 10/31/2013
Page 5
Frame Mounting Bracket installed with small factory tow hook and hardware
Insert Double Bolt Plate through the back of radiator core support cross member
Top Mounting Bracket
Fig 4A
Fig 6
(Fig 5B) Driver side pictured from above
Front
Fig 4B
The heavy duty factory tow hooks
Double Bolt Plate
Front
Front
Fig 5A
Page 4 of 7 10/31/2013
Driver/Left Side Installation Pictured
cannot be reinstalled and will not clear the Frame Mounting Brackets
Page 6
07-On Sequoia Pictured
Fig 10
Pull the Top Bracket forward as the
(2) 12mm x 35mm Hex Bolts
Fig
Insert a Plastic Washer
Top Bracket
Fig 8
Front
(1) Double Bolt Plate
Fig 7
Front
Driver side Top
10mm x 35mm Hex Bolts
Fig 9
Top Bracket
Front
(2) 10mm Flat Washers (2) 10mm Nylon Lock Nuts
(2) 12mm Lock Washers (2) 12mm Flat Washers (2) 12mm Plastic Washers
Page 5 of 7 10/31/2013
Driver/Left S ide Installation Pictured
Mounting Bracket (viewed from above)
10mm Lock Washers 10mm Flat Washers
hardware is tightened to provide maximum clearance between Grille Guard and vehicle
between the Grille Guard and the Frame Mounting Bracket on each 12mm Hex Bolt
Page 7
Pull Grille Guard to the
Loosen the top bolts (only if
Fig 15
Fig 16
(2) 10mm Plastic Washers
Insert a 10mm Plastic Washer between the Grille
(Fig 14) Pull handle to "open" Quick Release
10mm Quick Release Front
Front
Fig 12
Fig 13
Driver Side Installation Pictured
10mm Pivot Washer 10mm Flat Washer
necessary) to open the hood
Page 6 of 7 10/31/2013
(1) 10mm Flat Washer (1) 10mm Nylon Lock Nut
Guard and the Top Bracket and under the Flat Washer on each Quick Release Bolt. (2) Plastic Washers are required for each Quick Release
"open" position
Page 8
Push Grille Guard back
Quick Release in
Fig 17
Fig 18
Front
Complete Installation
Driver/Left S ide Installation Pictured
to the "closed" position
"closed" position
Opening and closing the hood
23. Lift the levers on the Quick Release bolt to release the clamping pressure, (Fig 11). Pull the Grille
Guard out and away from the vehicle to the "open" position, (Fig 12). NOTE: If the Grille Guard does not pivot to "open" position, slightly loosen the upper hex bolt on each Mounting Bracket, (Figure
13). WARNING! Do not completely loosen bolts or damage to the truck may occur.
24. Carefully pull on the Grille Guard until it is fully extended away from the vehicle, (Fig 12).
25. Pull the hood release and slowly open the hood.
26. IMPORTANT! Before closing the hood, always make sure that the Grille Guard is in the full open
position and away from the vehicle. Pull on the Grille Guard to verify that it is fully extended away from
the vehicle and slowly close the hood, (Fig 12).
27. Once the hood is completely closed, push the Grille Guard back to its "closed," upright position and tighten all hardware on the Grille Guard, (Fig 14). Push down on the Quick Release lever to tighten, (Fig 15). No tools are required to close the Quick Release levers. It will require some effort to open and
close by hand when properly adjusted. Loosen or tighten the 10mm Nylon Lock Nut on the Quick Release bolt to adjust the clamping pressure.
28. Do periodic inspections to the installation to make sure that all hardware is secure and tight.
Page 7 of 7 10/31/2013
Loading...