Aries Automotive B35-4005 User Manual

PARTS LIST:

1 Bull Bar 3 12mm Lock Washers
1 Driver/Left Mounting Bracket 5 12m ID x 29mm OD x 3mm Flat Washers
1 Passenger/Right Mounting Bracket 3 12mm Hex Nuts
1 12-1.75mm x 35mm Bolt Plate 4 8-1.25mm x 30mm Hex Head Bolts
2 Tube Spacers – 84mm 4 8mm Lock Washers
2 12-1.75mm x 140mm Hex Head Bolts 4 8mm ID x 17mm OD x 1.5mm Flat Washers

INSTALLATION INSTRUCTIONS

2007-10 SILVERADO 1500 TON / 2007-10 SIERRA 1500 TON

PART # B35-4005 / 35-4005

Passenger Side

Mounting Bracket

Tube Spacers

(2 pcs)

Driver Side

Mounting Bracket

12-1.75mm x 35mm

Bolt Plate

(1 pc)

Page 1 of 3 12/06/07 (AM)

PROCEDURE:

1. REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. READ
INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION.

2. NOTE: It may be necessary to remove/relocate front license plate and license plate bracket. It

is not required, but strongly recommended. If local/state law requires a license plate, license
plate relocation kit is available.

3. From underside of vehicle, remove the two bolts holding the driver factory tow hook, then
remove tow hook from vehicle. NOTE: This Bull Bar is not compatible with factory tow hooks,
so you will not be reinstalling factory tow hooks back onto vehicle.

4. Loosely attach Mounting Brackets to Bull Bar using the included (4) 8mm x 30mm Hex Head
Bolts, (4) 8mm Lock Washers, and (4) 8mm Flat Washers (Figure 1). Do not tighten at this
time. NOTE: Refer to figure above for bracket configuration.

5. With help slide the Bull Bar assembly through tow hook cavities and place Mounting Brackets
on the outer side of frame rails.

6. On the driver side you will be using the front tow hook hole that traverses the frame from side
to side to attach Mounting Bracket to frame rail. Insert (1) Tube Spacers through the front of
frame rail and align it with hole that traverses the frame rail (Figure 2). Secure the assembly
with the included (1) 12mm x 140mm Hex Head Bolt, (1) 12mm Lock Washer, (1) 12mm Hex
Nut, and (2) 12mm Flat Washers (Figure 3).

7. On the passenger side use the included (1) 12mm x 35mm Bolt Plate, (1) 12mm Lock
Washer, (1) 12mm Hex Nut, and (1) 12mm Flat Washer to attach Mounting Bracket to rear tow
hook hole. Repeat step 6 to attach Mounting Bracket to front tow hook hole (Figure 4).

8. Adjust Bull Bar properly, and then tighten all hardware at this time. NOTE: If you can’t reach
the Bull Bar Bolts (8mm hardware) from behind of bumper and through tow hook cavity, some
cutting might be necessary to the tow hook cavity in order to tighten the Bull Bar Bolts.

9. Do periodic inspections to the installation to make sure that all hardware is secure and tight.

To protect your investment, wax this product after installing. Regular waxing is recommended to

add a protective layer over the finish. Do not use any type of polish or wax that may contain abrasives
that could damage the finish.
For stainless steel: Aluminum polish may be used to polish small scratches and scuffs on the finish.
Mild soap may be used also to clean the Bull Bar.

For gloss black finishes: Mild soap may be used to clean the Bull Bar.

Fig 1

8mm x 30mm Hex Head Bolts
8mm Lock Washers
8mm Flat Washers

Page 2 of 3 12/06/07 (AM)