Aries Automotive 4081-2 User Manual

PARTS LIST:

1 Grille Guard 12 12mm ID x 30mm OD x 3mm Flat Washers
1 Driver/Left Mounting Bracket 6 12mm Nut
1 Passenger/Right Mounting Bracket 2 10-1.50mm x 40mm Hex Head Bolts
1 Driver/Left Top Bracket 2 10mm-1.50mm x 30mm Button Head bolts
1 Passenger/Right Top Bracket 4 10mm Nuts
6 12-1.75mm x 30m Hex Head Bolts 8 10mm ID x 26mm OD x 3mm Flat Washers
2 3mm x 49mm x 64mm Shims 4 10mm Lock Washers
6 12mm Lock Washers

INSTALLATION INSTRUCTIONS

GRILLE GUARD

2011 CHEVY SILVERADO HD2500/3500

4081/4081-2

Driver/ left

Mount bracket

Driver/ left

Upper bracket

Upper bracket

Shims

Passenger/ right

Mount bracket

Passenger/ right

Upper bracket

Page 1 of 3

PROCEDURE:

1. REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. READ INSTRUCTIONS
CAREFULLY BEFORE STARTING INSTALLATION.

2. Starting with the passenger/right side from underside of vehicle, remove the two bolts holding
the passenger factory tow hook, then remove tow hook from vehicle and set aside.

3. Determine driver and passenger side Mounting Brackets. NOTE: Refer to Figure above for

bracket configuration. From behind factory bumper, slide passenger side Mounting Bracket
through factory tow hook cavity, Insert factory tow hook back into frame. Secure Passenger
Mounting Bracket to frame using the same bolts to install the tow hook as shown in (Fig 1).
Snug but do not tighten at this time.

4. Repeat step 2-4 for driver/left side Mounting Bracket.

5. Open the hood and using a flat screw driver remove the ten push pin fasteners from plastic

shroud located on top of the radiator. Passenger/right side shown in (Fig 2) Remove plastic
shroud and set aside. With the shroud removed locate the tab of the bumper on the bottom
inner of the grill as shown in (Fig 3)

6. Select the passenger/right side upper bracket, NOTE: Refer to Figure above for bracket
configuration. Position top bracket through the bumper and grill opening, add the 3mm shim
between the bumper tab and bracket secure them using the (1) 10mm Hex bolt (2) 10mm flat
washers (1) 10mm lock washer and (1) 10mm nut. As shown in (Fig 4) Snug but do not tighten
at this time.

7. With help position Grille Guard on the outer side of Mounting Brackets. Align holes on the
Mounting Brackets with holes on the Grille Guard. Attach Grille Guard to Mounting Bracket
using the included (6) 12mm x 30mm Hex Head Bolts, (6) 12mm Nuts, and (12) 12mm Flat
Washers and (6) 12mm lock washers (Fig 5). Snug but do not tighten at this time.

8. Attach Grille Guard to Top Brackets using the included (2) 10mm x 30mm Button Head Bolts,
(2) 10mm Nuts, (2) 10mm lock washers and (4) 10mm Flat Washers as shown in (Fig 6). Snug
but do not tighten at this time.

9. Level and adjust Grille Guard, then tighten all hardware at this time.

10. Reinstall the plastic shroud back onto vehicle with the plastic push pins.

11. Do periodic inspections to the installation to make sure that all hardware is secure and tight.

To protect your investment, wax this product after installing. Regular waxing is recommended to

add a protective layer over the finish. Do not use any type of polish or wax that may contain abrasives
that could damage the finish.

For stainless steel: Aluminum polish may be used to polish small scratches and scuffs on the finish.
Mild soap may be used also to clean the Product.

For gloss black finishes: Mild soap may be used to clean the Product.

Page 2 of 3