Aries Automotive 3064-2 User Manual
Qty
Description
Qty
Description
1
Grill Guard
6
12mm Lock Washers
1
Driver/Left Lower Mount ing Bracket
6
12mm Nuts
1
Passenger/Right Lower Mount ing Bracket
2
10mm x mm Hex Bolts
1
Driver/Left Upper Brace B r ac k et
4
10mm Washers
1
Passenger/Right Upper B r ac e B r ac k et
2
10mm Lock Washers
6
12mm x 40mm Hex Bolts
2
10mm Nuts
12
12mm Flat Washers
INSTAL LATION INSTRUCTIONS
NOTE: (Vehicle Retains Tow Hook)
Passenger/Right
Driver/Left Side
Driver/left side
Passenger/right side
PARTS LIST:
Mounting
Upper brace bracket
2011-14 FORD SUPER DUTY
3064 / 3064-2
Side Mounting
Bracket
upper brace bracket
Page 1 of 3 8/13/2014
PROCEDURE:
1. REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. READ INSTRUCTIONS
CAREFULLY BEFORE STARTING INSTALLATION.
2. Starting with the Driver/Left side Begin your install by removing the bumper mount bolts
WARNING, Do not remove Passenger & Driver side bumper bolts at the same time as
bumper will drop down. Remove and install only one side at a time. (Fig 1) shows factory
bolts location. Select the Driver side mount bracket from the list of parts above and secure it to
the bumper with the factory bolts & nut plates (Fig 1 A) shows mount bracket attached. Snug,
but do not tighten hardware at this time. Repeat this step for the Passenger/Right side
installation
3. Proceed to install the upper brace brackets by first removing the black plastic trim cover on the
top edge of the trucks bumper (there are plastic tabs securing this down, by going through the
front opening of the bumper, pinch the tabs together and lift the plastic cover. Remove each
tab one at a time). Once plastic trim is removed, located on the inside top edge of the bumper,
there are 13mm bolts that need to be removed (Fig 2 shows plastic trim removed and
location of factory bolt). From the list above select the Driver/Left side upper brace bracket
and secure it to vehicle with the 13mm factory bolt (Fig 2A shows bracket attached). Snug
but do not tighten hardware at this time. Repeat this step for the Passenger/Right side
installation. In order to reinstall the plastic trim, a small section off the back edge must be
trimmed. Once brackets are in place overlay the plastic trim and mark the area where it
comes in contact with the upper brackets (inner edge under grill). Using a utility knife, tr im a
small section off the back. Trim before reattaching so it does not interfere with the upper
brackets. (Fig 3) shows Passenger side area to be trimmed, repeat for driver side.
4. With assistance begin to install Grill Guard. To mount brackets, move the Driver/Left side and
Passenger/Right side Mounting Brackets towards each other. The hardware should be kept
slightly loose to adjust. Position the bottom mounting holes of the Driver side Grill Guard to the
out side of the Mounting Brackets. Line up the three holes of the mount brackets w ith the lower
holes of the Grille Guard. Bolt them together with the included (3) 12mm Hex bolts, (6) 12mm
Flat Washers (3) 12mm lock washers and (3) 12mm Hex Nut per side (Fig 4 & 4A). Snug but
do not tighten hardware at this time. Repeat this step for the Passenger/Right side.
5. From step 3, bolt the brace brackets to the grill guard. Line up the hol e in the top brace bracket
with the one slotted in the upright plate of the Grill Guard. Secure with (1) 10mm hex bolt, (2)
10mm flat washer, (1) 10mm lock washer and (1) 10mm nut (FIG 2A Show Driver/S ide
brace bracket attached). Snug but do not tighten at this time. Repeat this step for the
passenger/right si de instal latio n.
6. Level and align Product properly. Tighten all hardware at this time. Do periodic inspections
making sure all hardware is secure and tight.
To protect your investment, wax this product after installing. Regular waxing is recommended to
add a protective layer over the finish. Do not use any type of polish or wax that may contain abrasives
that could damage the finish.
For stainless steel: Aluminum polish may be used to polish small scratches and scuffs on the finish.
Mild soap may be used also to clean the Product.
For gloss black finishes: Mild soap may be used to clean the Product.
Page 2 of 3 8/13/2014
Loading...