Aries Automotive 224046-2 User Manual

INSTALLATION INSTRUCTIONS

4” OVAL

ROCKER PANEL MOUNT

2014 1500 SILVERADO/SIERRA DOUBLE CAB

07-13 1500 SILVERADO/SIERRA EXTENDED CAB

07-14 25-3500 SILVERADO/SIERRA EXTENDED CAB

EXCLUDES DIESEL W/DEF

PART#224046-2 / S224046

5" OVAL BENT END SIDEBARS

r

r

ROCKER PANEL MOUNT

2014 1500 SILVERADO/SIERRA DOUBLE CAB

07-13 1500 SILVERADO/SIERRA EXTENDED CAB

07-14 25-3500 SILVERADO/SIERRA EXTENDED CAB

EXCLUDES DIESEL W/DEF

PARTS LIST:

Qty Description Qty Description

1 Driver side tube assembly 12 M8-1.25 Clip-On Nuts
1 Passenger side tube assembly 24 M8-1.25 x 25mm Hex Bolt
6 4” oval brackets 24 8mm lock washer

24 8mm x 24mm x 2mm flat washer

(6) Universal Mounting Brackets (NOTE: same
bracket used for left or right side installation)

Passenger/right sideba

Driver/left sideba

Front

PROCEDURE:
REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. READ INSTALLATION
INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION.

1. Start the installation under the driver side of the vehicle. Locate the 1st, 2nd and 4th mounting tabs

along the bottom edge of the body, (Figure 1). If necessary, hold the driver side Sidebar up in place to
help determine the correct mounting holes to use along the bottom of the body.

Vehicles with flat tab, no threaded hole: Select (1) 8mm Clip Nut. Slide the Clip Nut over the
first tab with the nut facing up behind the tab, (Figure 1). Line up threaded nut with hole in tab.
Vehicles with factory installed threaded insert in tab: Thread hex bolt into threaded insert
from the backside-down to clear paint as required.

2. Locate the inner mounting location on the back of the rocker panel directly above the flat tab in Step 1.
Vehicles without threaded hole: Remove the rubber plug from the larger hole, (Figure 2).

Select (1) 8mm Clip Nut. Slide the Clip Nut into the larger hole. Line up the threaded nut with
the smaller hole, (Figure 3).
Vehicles with factory installed threaded insert: Thread 8mm Hex Bolt into threaded insert to
clear paint as required. Use a small amount of oil if necessary, (Figure 1).

3. Select (1) Mounting Bracket. NOTE: Brackets are universal and will fit left or right side. Bolt the

Mounting Bracket to the Clip Nuts and/or the factory threaded holes with (2) 8mm Hex Bolts, (2) 8mm
Lock Washers and (2) 8mm Flat Washers, (Figure 4). Snug but do not fully tighten the hardware.

4. Repeat Steps 1 – 3 for all Bracket installations.

5. Carefully position the Driver Sidebar onto the (3) Mounting Brackets. Attach the Sidebar to the

Mounting Brackets with (6) 8mm x 25mm Hex Bolts, (6) 8mm Lock Washers and (6) 8mm Flat
Washers, (Figures 4). Do not tighten hardware at this time.

6. Level and adjust the Sidebar and tighten all hardware.

7. Repeat Steps 2 – 6 for passenger Sidebar installation.

8. Do periodic inspections to the installation to make sure that all hardware is secure and tight.

To protect your investment, wax this product after installing. Regular waxing is recommended to add a protective layer
over the finish. Do not use any type of polish or wax that may contain abrasives that could damage the finish.
For stainless steel: Aluminum polish may be used to polish small scratches and scuffs on the finish. Mild soap may be

used also to clean the Sidebar.
For gloss black finishes: Mild soap may be used to clean the Sidebar.

Page 1 of 2 7/23/13 (DP)