Aries Automotive 206010-2 User Manual

PARTS LIST:

INSTALLATION INSTRUCTIONS

2012 HONDA CRV

PART# 206010/206010-2

1 Driver Side Bar 8-1.25mm x 30mm Hex Head Bolts
1 Passenger Side Bar 8mm Lock Washers
1 Rear Driver Side Mounting Bracket (A) 8mm x 22mm x 3mm Flat Washers
1 Front Driver Side Mounting Bracket (B)
1 Front Passenger Side Mounting Bracket (C)
1 Rear Passenger Side Mounting Bracket (D)

PROCEDURE:

12
12
12

10mm x 30mm Hex Head Bolts

8

10mm Lock Washers

8

10mm x 22mm x 3mm Flat Washers

8

(A)

(B)

(C)

(D)

1. REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. READ

INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION.

2. Determine driver and passenger Mounting Brackets.

3. Hang the inner side of the driver front Mounting Bracket into position by partially threading (1)

8mm x 30mm Hex Head Bolt, (1) 8mm Lock Washer, and (1) 8mm Flat Washer into factory
threaded hole on the frame . NOTE: There are two threaded holes by the front mounting

(Fig 1)

location on the frame, use the one towards the rear of vehicle.

4. Attach the opposite side of the driver front Mounting Bracket to the threaded holes on the floor

panel of the vehicle by partially threading (2) 8mm x 30mm Hex Head Bolts, (2) 8mm Lock
Washers, and (2) 8mm Flat Washers .

(Fig 1)

5. Locate and cut out the openings in the driver and passenger side trimming templates with a pair of

scissors (Page 3 & 4)

6. Fit the driver’s side template onto its respective side plastic rock shields. Position them using two

each of the 8mm bolts. Transfer the openings
in the templates onto the plastic cover using a magic marker.

7. Now remove the rock shield from the undercarriage of the car. The three front screws can be
removed with a 10MM socket. The plastic retainer plugs can be removed with a flat blade
screwdriver.

8. Using a sharp knife or pair of shares, cut out the shields as marked using the templates

(Fig

2).

9. Insert the inner side of driver rear Mounting Bracket through previously cut out hole on the plastic

cover. Hang Mounting Bracket by partially threading (1) 8mm x 30mm Hex Head Bolt, (1) 8mm
Lock Washer, and (1) 8mm Flat Washer into factory threaded hole on the frame .

(Fig 3)

NOTE: There are two threaded holes on the frame, use the one towards the rear of vehicle.

10. Attach the opposite side on the driver rear Mounting Bracket by partially threading (2) 8mm x

30mm Hex Head Bolts, (2) 8mm Lock Washers, and (2) 8mm Flat Washers into factory threaded
holes on the floor panel.

11. Position Driver Side Bar onto Mounting Brackets. Attach Side Bar to Mounting Brackets using the

included (4) 10mm x 30mm Hex Head Bolts, (4) 10mm Lock Washers, and (4) 10mm Flat Washers

(Fig 1)

. Do not tighten at this time.

12. Level and adjust Side Bar; then tighten all hardware at this time.

13. Re-install the rest of fastener on the rock shield.

14. Repeat steps 2-13 for passenger Side Bar.

15. Do periodic inspections to the installation to make sure that all hardware is secure and tight.

Page 1

4 of

Fig 1

Do not use this hole

8mm x 30mm Hex Head Bolt,

8mm Lock Washer, &

8mm Flat Washer

Front Driver Side Mounting Bracket Shown

8mm x 30mm Hex Head Bolt,

NOTE: This picture is

for reference only. Rock
shield should be

hanging from rear
bracket at this point

8mm Lock Washer, &
8mm Flat Washer

10mm x 30mm Hex Bolts

8mm x 30mm Hex Head Bolt,

10mm Flat Washers &

8mm Lock Washer, &

10mm Lock Washers

Fig 2

Cut out the marked

location on the plastic

cover. See Drawings

below

Fig 3

Rear Driver Side Mounting Bracket Shown

Do not use these holes

8mm x 30mm Hex Head Bolt,

8mm Lock Washer, &

8mm Flat Washer

Page 2 of

4