Aries Automotive 2058-2 User Manual

INSTALLATION INSTRUCTIONS

GRILLE GUARD PART NUMBER

PARTS LIST:

1 Grille Guard 2
1 Passenger Side Mounting Bracket (D) 4 10-1.50mm x 25mm Hex Bolts
1 Driver Side Mounting Bracket (A) 6
1 Passenger Side Top Bracket (C) 10 10mm Flat Washers
1 Driver Side Top Bracket (B) 6
4 8-125mm x 115mm Hex Bolts 6 12mm Nylock Nuts
4 8mm Nylock Nuts 12 12mm Flat Washers
8 8mm Flat Washers

PROCEDURE:

1. REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. READ
INSTRUCTIONS CAREFULLY.

2. Locate the two existing holes on the front of the frame rail.

3. Position Passenger Side Mounting Bracket onto frame rail. NOTE: Mounting Bracket mounts
on the outer side of frame rails.

4. Line up holes on the Mounting Bracket with holes on the frame rail. Secure Mounting Bracket

with the included (2) 8-1.25mm x 115mm Hex Bolts, (2) 8mm Nylock Nuts, and (4) 8mm Flat
Washers (Figure 1 & 2). Do not tighten at this time.

5. Repeat steps 1-3 for driver side.

6. Once Both Mounting Brackets are installed, proceed to install the Top Brackets. Insert flat side

of Top Brackets through the upper section on the factory grille shell. Attach Top Brackets to
Mounting Brackets by using the included (4) 10-1.50mm x 25mm Hex bolts, (4) 10mm Nylock
Nuts, and (8) 10mm Flat Washers (Figure 3). Do not tighten at this time.

7. With help position Grille Guard on the outer side of Mounting Brackets. Line up holes on the
Mounting Bracket with holes on the Grille Guard.

8. Attach Grille Guard to Mounting Brackets using the included (6) 12-1.75mm x 30mm Hex
Bolts, (6) 12mm Nylock Nuts, and (12) 12mm Flat Washers (Figure 3). Do not tighten at this
time.

9. Once the bottom brackets are loosely installed, proceed to attach Grille Guard to Top Brackets
by using the included (2) 10-1.50mm Button Head Bolts, (2) 10mm Nylock Nuts, and (2) 10mm
Flat Washers (Figure 4). Do not tighten at this time.

10. Level and adjust grille guard; then proceed to tighten all hardware at this time.

11. Do periodic inspections to the installation to make sure that all hardware is secure and tight.

03-07 TOYOTA 4RUNNER

10-1.50mm x 25mm Button Head Bolts

10mm Nylock Nuts

12-1.75mm x 30mm Hex Bolts

2058/2058-2

(A)

(B)

(D)

(C)

Page 1 of 2 1/31/07 (AM)

g

g

p

Bottom view of Passenger Side

Mountin

Bracket

Top view of Passenger Side

Mountin

Bracket

Figure 1 Figure 2

8mm x 115mm Hex Bolts,

8mm Nylock Nuts, &

Passenger Side Shown

Passenger Side

Bracket

To

10mm x 25mm Hex Bolts,

10mm Nylock Nuts, &

12mm x 30mm Hex Bolts,

12mm Nylock Nuts, &

Figure 3

Installation Complete Passenger Side Shown

Plate

Figure 4 Figure 5

Page 2 of 2 1/31/07 (AM)

10mm x 25mm Button Bolt,

10mm Nylock Nuts, &