Page 1
# 2030
030
INSTALLATION INSTRUCTIONS
3" SIDEBARS
2013 FORD ESCAPE
PART
42-2/2
42
Page 2
2013 FORD ESCAPE
PARTS LIST: -
Qty Description Qty Description
1 Driver / Left Sidebar 2 12mm Plastic Retainers
1 Passenger / Right Sidebar 8 10mm Plastic Retainers
1 Driver / Left Front Mounting Bracket 2 12mm x 32mm OD x 3mm Flat Washers
1 Passenger / Right Front Mounting Bracket 2 12mm Lock Washers
1 Driver / Left Center Mounting Bracket 2 12mm Hex Nuts
1 Passenger / Right Center Mounting Bracket 8 10mm x 27mm OD x 3mm Flat Washers
1 Driver / Left Rear Mounting Bracket 8 10mm Lock Washers
1 Passenger / Right Rear Mounting Bracket 8 10mm Hex Nuts
2 12mm x 35mm Special Bolt Plate (Rear) 12 8-1.25mm x 30mm Hex Bolts
5 10mm x 30mm Button Head Bolt Plates 12 8mm x 24mm OD x 2mm Flat Washers
2 10mm x 30mm T-Bolts (Both Front Outer) 12 8mm Lock Washers
10mm x 35mm Small T-Bolts (Driver Front Inner
1
only)
Passenger/Right
Rear Mounting
Bracket
Driver/Left Rear
Mounting Bracket
(2) 12mm x 35mm Bolt Plate
(Rear Brackets)
Passenger/Right
Center Bracket
(5) 10mm x 30mm Bolt Plates
(1) 10mm x 35mm Small T-Bolt
(Driver Front Bracket Only)
Driver/Left
Center Bracket
Passenger/Right Front
Mounting Bracket
Driver/Left Front
Mounting Bracket
(2) 10mm x 30mm Large T-Bolt
(Outer Front Brackets)
PROCEDURE:
Driver/Left Sidebar
1. REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. READ INSTRUCTIONS
CAREFULLY BEFORE STARTING INSTALLATION. CUTTING IS REQUIRED. ASSISTANCE IS
RECOMMENDED.
2. Start installation under the driver side of the vehicle. NOTE: To help determine the correct mounting
holes to use, hold the front Bracket up in position against the floor panel and line up the Bracket with
the correct holes, (Fig. 1).
a. Driver side front Bracket installation:
Select (1) 10mm x 30mm Small T-Bolt and (1) 10mm Plastic Retainer, (Fig. 2A). Partially thread
the Retainer onto the T-Bolt. Insert the T-Bolt into the inner factory oval hole, (Fig. 1 & 3). Rotate
Passenger/Right Sidebar
Front
3" SIDEBARS
Page 1 of 7 9/26/12 (DP)
Page 3
3" SIDEBARS
2013 FORD ESCAPE
the T-Bolt 90-degrees so that the plate is across the slot. Thread the Retainer down until it is tight
against the floor panel. The Retainer is designed to help hold the T-Bolt in place during Bracket
installation.
Next, insert (1) 10mm x 35mm Large T-Bolt with (1) Plastic Retainer into the outer oval hole in the
floor panel next to the pinch weld as previously described, (Fig. 2B & 3).
b. Passenger side front Bracket installation:
IMPORTANT-Repeat the previous Step 2a for passenger side Bracket installation but note that
the inner mounting tab on the front Bracket will use (1) 10mm x 30mm Button Head Bolt Plate,
(same bolt plate as used on center and rear Brackets), inserted into a round hole in place of the
10mm Small T-Bolt, (Fig. 2B, 4 & 5). Do not use the Small T-Bolt for passenger side Bracket.
3. Hang the driver side Front Bracket from the T-Bolts with (2) 10mm Flat Washers, (2) 10mm Lock
Washers and (2) 10mm Hex Nuts, (Fig. 6). Do not tighten hardware at this time.
4. Release the plastic clips attaching the lower plastic rocker panel cover to the body, (Fig. 7).
5. Measure 40" back from the bottom corner of the wheel opening to locate the correct factory hole under
the plastic rocker cover for the center Bracket, (Fig. 8). Pull plastic cover outward to access the hole,
(Fig. 10). Partially thread (1) 10mm Plastic Retainer onto (1) 10mm x 30mm Button Head Bolt Plate,
(Fig. 9). Insert Bolt Plate into the round hole and thread the Retainer down against the body, (Fig. 10).
6. Select the driver side center Bracket, (Fig. 11A). Insert the Center Bracket into the approximate
position, (Fig. 11B). Mark the Bracket location on the bottom edge of the plastic cover, (Fig. 12). Cut a
small slot in the bottom edge of the cover to clear the Bracket. Bolt the Bracket to the Bolt Plate with (1)
10mm Flat Washer, (1) 10mm Lock Washer and (1) 10mm Hex Nut, (Fig. 13). Do not tighten hardware
at this time.
7. Move to the rear location and remove the plastic cover on the floor panel, (Fig. 14). Locate the small
round hole under the plastic rocker cover, (Fig. 16). Select (1) 10mm x 30mm Button Head Bolt Plate
and (1) 10mm Plastic Retainer (Fig. 15). Insert the Bolt Plate into the round hole as described in Step
5, (Fig. 16 & 17).
8. Next, locate the large round hole in the floor panel. Insert (1) 12mm x 35mm Bolt Plate into the large
round hole and out the smaller hole toward the front, (Fig. 18 & 19). Slide the driver side Rear Bracket
under the plastic rocker cover and over the (2) Bolt Plates, (Fig. 20). Secure the Bracket to the outer
10mm Bolt Plate with (1) 10mm Flat Washer, (1) 10mm Lock Washer and (1) 10mm Hex Nut. Attach
the Bracket to the Larger 12mm Bolt Plate with (1) 12mm Flat Washer, (1) 12mm Lock Washer and (1)
12mm Hex Nut. , (Fig. 20). Do not tighten hardware at this time.
9. Hold the plastic cover removed in Step 7, up in position. Trace the location of the rear Bracket onto the
cover, (Fig. 21). Carefully cut the cover to clear the Bracket, (Fig. 22A & 22B). IMPORTANT: Cut as
little as possible from the cover. Do not cut off the mounting area for the factory hardware, (Fig. 22B).
Reinstall the plastic cover and all plastic clips holding the bottom of the rocker cover to the body panel.
Check the direction of the cradles on all Brackets before proceeding, (Fig. 23).
10. Carefully unwrap and select the driver Sidebar. Place the Sidebar in position on top of the (3) Brackets.
NOTE: It may be necessary to loosen the Brackets slightly to line up the cradles with the threaded
inserts in the Sidebars. Bolt the Sidebar to the Brackets with (6) 8mm x 30mm Hex Bolts, (6) 8mm Lock
Washers and (6) 8mm flat washers, (Fig. 24).
11. Level and adjust the Sidebar and tighten all hardware.
12.
Repeat Steps 2 – 11 for passenger Sidebar installation. NOTE: See specific passenger side front
Bracket installation info in Step 2b.
13. Do periodic inspections to the installation to make sure that all hardware is secure and tight.
To protect your investment, wax this product after installing. Regular waxing is recommended to add a protective layer
over the finish. Do not use any type of polish or wax that may contain abrasives that could damage the finish.
For stainless steel: Aluminum polish may be used to polish small scratches and scuffs on the finish. Mild soap may be
used also to clean the Sidebar.
For gloss black finishes: Mild soap may be used to clean the Sidebar.
Page 2 of 7 9/26/12 (DP)
Page 4
3" SIDEBARS
2013 FORD ESCAPE
Driver/Left Side Installation Pictured
Front
(Fig 2A) Small 10mm x 35mm T-Bolt
for driver side inner front bracket only
(Fig 1) Driver side front
mounting location pictured
(Fig 2B) Large 10mm x 30mm T-Bolt
for driver and passenger side outer
location on front brackets only
Front
(Fig 3) Driver side pictured
(Fig 4) Passenger side front
mounting location pictured
(Fig 5) Use 10mm x 30mm Bolt Plate for
passenger side inner location (same bolt
plate used on center and rear brackets)
Page 3 of 7 9/26/12 (DP)
Page 5
Driver Side Installation Pictured
(2) 10mm Flat Washers
(2) 10mm Lock Washers
(2) 10mm Hex Nuts
Fig 6
40"
(Fig 8) Measure approximately 40 inches from
bottom corner of wheel opening along rocker
panel to locate factory hole for center Bracket
(Fig 10) 10mm x 30mm Bolt
Plate with Plastic Retainer
3" SIDEBARS
2013 FORD ESCAPE
Front
Rear
(Fig 7) Release all clips along
bottom of rocker panel cover
(Fig 9) 10mm x 30mm Bolt Plate
Page 4 of 7 9/26/12 (DP)
Page 6
0
ut
Driver Side Installation Pictured
Driver/Left
Bracket
Passenger/Right
Bracket
Fig 11A
Front
Fig 12
Dotted line represents area to cut from bottom
edge of rocker panel cover to clear center Bracket
Rear
(Fig 14) Remove plastic cover
3" SIDEBARS
2013 FORD ESCAPE
(Fig 11B) Hold correct center Bracket up
in place to determine area to cut from
bottom edge of rocker panel cover
10mm Flat Washer
10mm Lock Washer
1
mm Hex N
Front
Fig 13
Page 5 of 7 9/26/12 (DP)
Page 7
3" SIDEBARS
e
ut
0
ut
2013 FORD ESCAPE
Driver Side Installation Pictured
(Fig 15) 10mm x 30mm Bolt Plate
Rear
(Fig 16) Rear mounting location with
Bolt Plate pictured from below
Rear
(Fig 17) Rear mounting location with
Bolt Plate pictured from below
(Fig 18) 12mm x 35mm Bolt
Plate for rear Bracket only
12mm Flat Washer
12mm Lock Washer
12mm H
x N
10mm Flat Washer
10mm Lock Washer
1
mm Hex N
Rear
Rear
(Fig 19) Insert 12mm Bolt Plate into
large hole and out smaller hole
(Fig 20) Rear Bracket pictured from below
Page 6 of 7 9/26/12 (DP)
Page 8
Driver Side Installation Pictured
(Fig 21) Hold plastic cover up in position
to determine area to cut from cover
(Fig 22B) Do not cut mounting area off of cover
Fig 24
Complete Installation
3" SIDEBARS
2013 FORD ESCAPE
Rear
(Fig 22A) Dashed line represents
area to cut from cover to clear
Front
(Fig 23) Note correct direction
of cradles on Brackets
8mm x 30mm Hex Bolts
8mm Flat Washers
8mm Lock Washers
Page 7 of 7 9/26/12 (DP)
Loading...