Aries Automotive 203033-2 User Manual
1998-09 RANGER EDGE SUPER CAB
1998-09 MAZDAB-SERIES P/U SUPER CAB
Part # 203033 / 203033-2
EXT. CAB
REG. CAB
ITEM
1,2 2 STEP BAR, PASSENGER (1)ANDDRIVER
3,4
5,6 2 REAR BRACKET
7,8 2 MOUNT PLATEASSEMBLY, PASSENGER (7) AND DRIVER (8)
9,10 2 SUPPORT BRACE
11 2 1/2-13 X 2.50” HEX HEAD BOLT
12 2 1/2-13 X 2.00” HEX HEAD BOLT
13 4
14 4
15 10 3/8-16 X 1.25” HEX HEAD BOLT
16 16 3/8” FLATWASHER
17 10 3/8” LOCK WASHER
18 6 3/8-16 HEX NUT
QTY
2 FRONT BRACKET, PASSENGER(3)AND DRIVER (4)
1/2” FLATWASHER
1/2” LOCK WASHER
Step 1.
Step 2.
Step 3.
Step 4.
Step 5.
Step 6.
Remove the contents from box and check for damage. Verify all parts are present. Read instructions completely
before beginning.
Attach front brackets and support braces using 3/8” fasteners as shown.
Temporarily attach rear bracket to vehicle through hole as shown. Carefully cut out templates
and align with visible portionof rear bracket. Tape template in place and mark center of top hole with center
punch. Remove template and bracket from vehicle. Drill 7/16” diameter hole at this location.
NOTE:
quired.
Attach rear brackets to the backside of rocker panel using 3/8” fasteners as shown.
Attach step bars to brackets using 1/2” fasteners as shown.
Make sure step bar and brackets are properly aligned with vehicle and tighten fasteners. Recommended torque
value is 26 Ft. Lbs. for 3/8” fasteners and 64 Ft. Lbs. for 1/2” fasteners.
CONTENTS -
(2)
, PASSENGER (5) AND DRIVER (6)
, PASSENGER (9) AND DRIVER (10)
If hole on rocker panel aligns with T-Slot on mount bracket fasten at this location. Drilling is not re-
SEE FIGURE 6.
3
4
SEE FIGURE 4.
5 7 9
6 8
SEE FIGURES 1 THROUGH 3.
10
TOOLS -
3/4” SOCKET
9/16” SOCKET
9/16” WRENCH
*7/16” DRILL BIT
*DRILL
CENTER PUNCH
HAMMER
RATCHET
TORQUE WRENCH
*NOTE: A SHORT 7/16” BIT WITH A 3/8”
SHANK AND A SMALL OR RIGHT ANGLE
DRILL MAY BE NECESSARY FOR EASIER
INSTALLATION.
SEE FIGURE 5.
FINISH PROTECTION- ARIES PRODUCTS HAVE A HIGH FINISH THAT MUST BE MAINTAINED SUCH AS
ANY OTHER HIGH FINISH PRODUCT ON THE VEHICLE. PROTECT THE FINISH WITH A NON-ABRASIVE
AUTOMOTIVE WAX. THE USE OF SOAP, POLISH, OR WAX THAT CONTAINS ABRASIVES IS DETRIMENTAL,
AS THE COMPOUNDS SCRATCH THE FINISH AND OPEN IT TO CORROSION.
DISCLAIMER- BUYER ASSUMES ALL RISK AND LIABILITY WHATSOEVER FROM THE INSTALLATION
AND USE OF ARIES PRODUCTS. ARIES PRODUCTS ARE SOLD AS DECORATIVE ACCESSORIES AND
SHOULD NOT BE RELIED UPON AS PROTECTION FOR THE VEHICLE OR OCCUPANTS IN THE EVENT OF A
COLLISION OR ROLL OVER. ARIES AUTOMOTIVE ASSUMES NO LIABILITY FOR INJURY, LOSS.
1
2
3
7
16
17
15
3
17
18
16
4
9
DRILL IF REQUIRED
16
15
5
16
15
6
ALIGN TEMPLATE
5
18
17
16
INSTALLATION VIEW OF PASSENGER SIDE SHOWN, DRIVER SIDE OPPOSITE
Aries Automotive Accessories, Inc.
P.O. Box 1687 Lomita, CA 90717
14
13
11
12
13
14
1
Customer Service Phone # (888) 800-2743
Loading...