Page 1
Power Brush 36
E10
Owner/Operator Manual
Manuel Du Propriétaire/Utilisate ur
Model
926057 – Power Brush 36
(Serial No. 000101 +)
The use of any gasoline exceeding 10% ethanol (E10) or
10% MTBE will void the product warranty.
L’utilisation d’une essence contenant plus de 10% d’éthanol
(E10) ou de 10% de MTBE annulent la garantie.
ENGLISH
FRANÇAIS
04653900 4/13
Printed in USA
Page 2
TABLE OF CONTENTS
Figure 1
OS7010
Serial Number Label
Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Assembly . . . . . . . . . . . . . . . . . . . . . . . . 8
Controls & Features. . . . . . . . . . . . . . . 10
Operation . . . . . . . . . . . . . . . . . . . . . . . 11
Maintenance. . . . . . . . . . . . . . . . . . . . . 16
Service & Adjustments . . . . . . . . . . . . 20
INTRODUCTION
Storage . . . . . . . . . . . . . . . . . . . . . . . . . 27
Trouble s hooting. . . . . . . . . . . . . . . . . . 28
Service Parts . . . . . . . . . . . . . . . . . . . . 28
Specifications . . . . . . . . . . . . . . . . . . . 29
Warranty. . . . . . . . . . . . . . . . . . . . . . . . 30
THE MANUAL
Before operation of unit, carefully and
completely read your manuals. If used
improperly, this unit could be dangerous and
cause personal injury or property damage.
The contents will provide you with safety
instructions for the safe use of your unit
during normal operation and maintenance.
All reference to left, right, front, or rear are
given from operator standing in operation
position and facing the direction of forward
travel.
ENGINE MANUAL
The engine on this unit is covered by a
separate manual specific to the engine. This
manual is included in the literature package
that shipped with the unit. Refer to this
manual for engine service recommendations.
If the engine manual is not available, contact
the engine manufacturer for a replacement
manual.
MODEL AND SERIAL NUMBERS
When ordering replacement parts or making
service inquiries, know the Model and Serial
numbers of your unit and engine.
Numbers are located on the product
registration form in the unit literature
package. They are printed on a serial number
label, located on the frame of your unit.
• Record Unit Model and Serial number
here.
• Record Engine Model and Serial
number here.
PRODUCT REGISTRATION
The Ariens dealer must register the product
at the time of purchase. Registering the
product will help the company process
warranty claims or contact you with the latest
service information. All claims meeting
requirements during the limited warranty
period will be honored, whether or not the
product registration card is returned. Keep a
proof of purchase if you do not register your
unit.
Customer Note: If Dealer does not register
your product, please fill out, sign and return
the product registration card to Ariens or go
to www.ariens.com.
UNAUTHORIZED REPLACEMENT
PARTS
Use only Ariens replacement parts. The
replacement of any part on this unit with
anything other than an Ariens authorized
replacement part may adversely affect the
performance, durability, or safety of this unit
and may void the warranty. Ariens disclaims
liability for any claims or damages, whether
warranty, property damage, personal injury or
death arising out of the use of unauthorized
replacement parts. To locate your nearest
Ariens Dealer, go to www.ariens.com on the
Internet.
EN - 2
Page 3
DISCLAIMER
Ariens reserves the right to discontinue,
make changes to, and add improvements
upon its products at any time without public
notice or obligation. The descriptions and
specifications contained in this manual were
in effect at printing. Equipment described
within this manual may be optional. Some
illustrations may not be applicable to your
unit.
DELIVERY
Customer Note: If you have purchased this
product without complete assembly and
instruction by your retailer, it is your
responsibility to:
1. Read and understand all assembly
instructions in this manual. If you do not
understand or have difficulty following
the instructions, contact your nearest
Ariens Dealer for assistance. Make sure
all assembly has been properly
completed.
SAFETY
NOTE: To locate your nearest Ariens Dealer,
go to www.ariens.com on the Internet.
WARNING: Improper assembly or
adjustments can cause serious
injury.
2. Understand all Safety Precautions
provided in the manuals.
3. Review control functions and operation
of the unit. Do not operate the unit
unless all controls function as described
in this manual.
4. Review recommended lubrication,
maintenance and adjustments.
5. Review Limited Warranty Policy.
6. Fill out Original Purchaser Registration
Card and return the card to Ariens
Company or go to www.ariens.com on
the internet.
WARNING: To avoid injury to
hands and feet, always disengage
clutches, shut off engine, and wait
for all movement to stop before
unclogging or working on brush.
Keep hands and feet away from
brush.
SAFETY ALERT SYMBOL
These are safety alert
symbols. They mean:
• ATTENTION!
• YOUR SAFETY IS
INVOLVED!
When you see this symbol:
• BECOME ALERT!
• OBEY THE MESSAGE!
SIGNAL WORDS
The safety alert symbols above and signal
words below are used on decals and in this
manual.
Read and understand all safety messages.
DANGER: IMMINENTLY
HAZARDOUS SITUATION! If not
avoided, WILL RESULT in death or
serious injury.
WARNING: POTENTIALLY
HAZARDOUS SITUATION! If not
avoided, COULD RESULT in death
or serious injury.
CAUTION: POTENTIALLY
HAZARDOUS SITUATION! If not
avoided, MAY RESULT in minor or
moderate injury. It may also be used
to alert against unsafe practices.
NOTATIONS
NOTE: General reference information for
proper operation and maintenance practices.
IMPORTANT: Specific procedures or
information required to prevent damage to
unit or attachment.
PRACTICES AND LAWS
Practice usual and customary safe working
precautions, for the benefit of yourself and
others. Understand and follow all safety
messages. Be alert to unsafe conditions and
the possibility of minor, moderate, or serious
injury or death. Learn applicable rules and
laws in your area. Always follow the practices
set forth in this manua l .
EN - 3
Page 4
REQUIRED OPERATOR
077541
07800330
12
07800331
Figure 2
1
2
3
4
5
TRAINING
Original purchaser of this unit was instructed
by the seller on safe and proper operation. If
unit is to be used by someone other than
original purchaser; loaned, rented or sold,
ALWAYS provide this manual and any
needed safety training before operation.
1. WARNING!
Danger!
SAFETY DECALS AND
LOCATIONS
ALW AYS replace missing or damaged Safety
Decals. Re fe r to Figure 2 for Safety Deca l
locations.
Never direct discharge
towards persons or
property that may be
injured or damaged by
thrown objects.
Keep children and people
away. Keep children out of
work area and under
watchful care of a
responsible adult.
Stop engine, remove key,
read manual before
making any repairs or
adjustments.
Read Owner/Operator
Manual.
Allow operation only by
properly trained adult,
never children.
Wear appropriate hearing
protection. Always wear
safety goggles or safety
glasses with side shields
when operating.
Operator should wear a
dust particle mask at all
times while clearing debris
EN - 4
Page 5
2. CAUTION!
1
2
3. DANGER!
Danger!
Be sure to engage the
traction drive clutch first.
Engaging the attachment
clutch before traction drive
clutch can cause the unit to
travel backwards.
Danger!
Keep clear of brush while
engine is running.
NEVER use your hands to
clear blockages.
Operating on irregular
terrain could cause the
brush to dig in and drive
the machine rearward.
Read Owner/Operator
Manual.
Allow operation only by
properly trained adult,
never children.
4. HOT SURFACES!
DO NOT touch parts which
are hot from operation.
ALWAYS allow parts to
cool.
5. DANGER!
Danger!
Always keep hands and
feet away from all pinch
points.
EMISSION CONTROL SYSTEM
This equipment and/or its engine may include
exhaust and evaporative emissions control
system components required to meet U.S.
Environmental Protection Agency (EPA)
and/or California Air Resources Board
(CARB) regulations. Tampering with
emission controls and components by
unauthorized personnel may result in severe
fines or penalties. Emission controls and
components can only be adjusted by an
Ariens Company dealer or an authorized
engine manufacturer's service center.
Contact your Ariens Company Equipment
Retailer concerning emission controls and
component questions.
SAFETY RULES
Read, understand, and follow all safety
practices in Owner/Operator Manual before
beginning assembly or operating. Failure to
follow instructions could result in personal
injury and/or damage to unit.
ALWAYS remove key and/or wire from spark
plug before assembly, maintenance or
service. Unintentional engine start up can
cause death or serious injury.
Complete a walk around inspection of unit
and work area to understand:
• Work area • Your unit • All safety decals
ALWAYS check overhead and side
clearances carefully before operation.
ALWAYS be aware of traffic when operating
along streets or curbs.
EN - 5
Page 6
Keep children and people away. Keep
children out of work area and under watchful
care of a responsible adult.
NEVER allow children to operate or play on
or near unit. Be alert and shut off unit if
children enter area.
DO NOT allow adults to operate unit without
proper training. Only trained adults may
operate unit. Training includes being familiar
with controls and actual operation.
Keep area of operation clear of all toys, pets,
and debris. Thrown objects can cause injury.
Check for weak spots on docks, ramps or
floors. Avoid uneven work areas and rough
terrain. Stay alert for hidden hazards.
DO NOT operate near drop-offs, ditches, or
embankments. Unit can suddenly turn over if
a wheel is over the edge of a cliff or ditch, or if
an edge caves in.
Falling snow, fog, etc. can reduce vision and
cause an accident. Operate unit only when
there is good visibility and light.
NEVER operate unit after or during the use of
medication, drugs or alcohol. Safe operation
requires your complete and unimpaired
attention at all times.
NEVER allow anyone to operate this unit
when their alertness or coordination is
impaired.
DO NOT operate unit without wearing
adequate outer garments. Wear adequate
safety gear, including safety glasses with side
shields, and protective gloves. Wear proper
footwear to improve footing on slippery
surfaces.
DO NOT wear loose clothing or jewelry and
tie back hair that may get caught in rotating
parts.
Protect eyes, face and head from objects that
may be thrown from unit. Wear appropriate
hearing protection.
Avoid sharp edges. Sharp edges can cut.
Moving parts can cut off fingers or a hand.
ALWAYS keep hands and feet away from all
rotating parts during operation. Rotating parts
can cut off body parts.
NEVER place your hands or any part of your
body or clothing inside or near any moving
part while unit is running.
ALWAYS keep hands away from all pinch
points.
DO NOT touch unit parts which might be hot
from operation. Allow parts to cool before
attempting to maintain, adjust or service.
Never direct discharge towards persons or
property that may be injured or damaged by
thrown objects. Use extreme caution on
gravel surfaces. Stay alert for hidden hazards
or traffic.
Deflected materials can cause injury and
property damage.
Always stand clear of the discharge area
when operating this unit.
Fumes from engine exhaust can cause injury
or death. DO NOT run engine in an enclosed
area. Always provide good ventilation.
ALWAYS disengage attachment, stop unit
and engine, remove key and allow moving
parts to stop before leaving operator’s
position.
Read, understand, and follow all instructions
in the manual and on the machine before
starting.
Understand:
• How to operate all controls.
• The functions of all controls.
• How to STOP in an emergency.
Before starting engine, disengage control(s).
Use only approved extension cords and
receptacles when starting units equipped with
electric starter. DO NOT connect electric
starter cord to any wiring system that is not a
three-wire grounded system.
ALWAYS allow unit and engine to adjust to
outdoor temperatures before clearing snow.
Always be sure of your footing, especially
when operating in reverse or leaving the
operator’s position. Walk, never run during
operation.
DO NOT overload the machine capacity by
attempting to clear debris at too fast a rate.
Slow down and turn corners slowly.
Do not operate in reverse unless absolutely
necessary. ALWAYS back up slowly. Always
look down and behind before and while
backing.
Disengage attachment drive when traveling
from one work area to another.
Abnormal vibrations are a warning of trouble.
Striking a foreign object can damage unit.
Immediately stop unit and engine. Remove
key and wait for all moving parts to stop.
Remove wire from spark plug. Inspect unit
and make any necessary repairs before
restart.
Before cleaning, removing clogs or making
any inspections, repairs, etc.: disengage
clutch(es), stop unit and engine, remove key,
allow moving parts to stop. Allow hot parts to
cool.
Run unit a few minutes after clearing snow to
prevent freeze-up of attachment.
Disengage attachment when not in use.
Disengage all clutches before starting engine.
Never leave a running unit unattended.
ALWAYS shut off engine before leaving unit.
ALW A YS remove key to prevent unauthorized
use.
Never carry passengers.
EN - 6
Page 7
Adjust brush height before operating. Engage
traction drive clutch before attachment clutch.
If brush is set too low or if terrain is irregular
brush can drive machine rearward.
DO NOT operate on steep slopes.
DO NOT clear debris across the face of
slopes. Keep all movement on slopes slow
and gradual. DO NOT make sudden changes
in speed or direction. Use a slow speed to
avoid stops or shifts on slopes. Avoid starting
or stopping on a slope.
DO NOT park unit on a slope unless
absolutely necessary. When parking on a
slope always block the wheels.
ALWAYS shut off engine, remove key, and
close fuel shut-off valve or drain fuel when
transporting unit on a truck or trailer.
Use extra care when loading or unloading
unit onto trailer or truck.
Secure unit chassis to transport vehicle.
NEVER secure from rods or linkages that
could be damaged.
DO NOT transport machine while engine is
running.
Keep unit free of ice or other debris. Clean up
oil or fuel spills.
This product is equipped with an internal
combustion type engine. DO NOT use unit on
or near any unimproved, forest-covered or
brush covered land unless exhaust system is
equipped with a spark arrester meeting
applicable local, state or federal laws. A spark
arrester, if it is used, must be maintained in
effective working order by operator.
Fuel is highly flammable and its vapors are
explosive. Handle with care. Use an
approved fuel container with an appropriately
sized dispensing spout.
NO smoking, NO sparks, NO flames.
ALWAYS allow engine to cool before
servicing.
NEVER fill fuel tank when engine is running
or hot from operation.
NEVER fill or drain fuel tank indoors.
Replace fuel cap securely and clean up
spilled fuel.
Never fill containers inside a vehicle or on a
truck or trailer bed with a plastic liner. Always
place containers on the ground away from
your vehicle before filling.
When practical, remove gas-powered
equipment from the truck or trailer and refuel
it on the ground. If this is not possible, then
refuel such equipment on a trailer with a
portable container, rather than from a
gasoline dispenser nozzle.
Keep the nozzle in contact with the rim of the
fuel tank or container opening at all times until
fueling is complete. Do not use a nozzle lockopen device.
If fuel is spilled on clothing, change clothing
immediately.
Adjust brush height before operating. Refer to
Operation.
Before separating brush attachment from unit
frame, remove fuel so no spills will occur.
Ensure unit is secure and will not tip over
during maintenance.
ALWAYS keep protective structures, guards,
and panels in good repair, in place and
securely fastened. NEVER modify or remove
safety devices.
DO NOT change engine governor settings or
over-speed engine.
Fumes from engine exhaust can cause injury
or death. DO NOT run engine in an enclosed
area. Always provide good ventilation.
ALWAYS maintain unit in safe operating
condition. Damaged or worn out muffler can
cause fire or explosion.
Keep all hardware properly tightened.
Maintain or replace safety and instruction
labels, as necessary.
NEVER store unit with fuel in fuel tank, inside
a building where any ignition sources are
present such as hot water heaters, space
heaters, or clothes dryers. Allow the engine to
cool before storing in any enclosure.
Shut off fuel and allow engine to cool
completely before storing in closed area or
covering unit.
For extended storage, clean unit thoroughly.
See Engine Manual for proper storage.
Use only attachments or accessories
designed for your unit.
Check components frequently. If worn or
damaged, replace with manufacturer’s
recommended parts.
EN - 7
Page 8
ASSEMBLY
Figure 3
1.Handlebar Hardware
2.Shift Rod Hardware
3.Shift Rod
4.Speed Selector Lever
1
3
2
4
WARNING: AVOID INJURY. Read
and understand the entire Safety
section before proceeding.
Tools Required:
•Tire Gauge
• Pliers
• 1/2-In. 3/8-In, 7/16-In, and 9/16-In
Wrench and/or Adjustable Wrench
Unpacking Unit
WARNING: Dropping or tipping
over boxed unit could result in
personal injury or damage to unit.
Unfold Handlebar
(Figure 3)
1. Remove the lower and loosen the upper
hardware on the handlebar assembly.
2. Loosen the hardware on the shift rod.
3. Put the speed selector lever in the
second reverse position.
4. Rotate the handlebars into operating
position.
IMPORTANT: Be careful not to damage cable
spring hooks when rotating handlebars
upward.
5. Install and tighten all hardware on the
handlebar assembly and shift rod.
Check Function of Dual Handle
Interlock
Without the engine running, press down
(engage) both clutch levers. Release
attachment clutch lever. Attachment clutch
should remain engaged until traction clutch
lever is released, then both clutches must
disengage. If they do not, contact your Dealer
for repairs.
EN - 8
Page 9
Check Tire Pressure
Check tire pressure and adjust to the
pressure listed on tire sidewall.
CAUTION: Avoid injury! Explosive
separation of tire and rim parts is
possible when they are serviced
incorrectly:
• Do not attempt to mount a tire
without the proper equipment
and experience to perform
the job.
• Do not inflate the tires above
the recommended pressure.
• Do not weld or heat a wheel
and tire assembly. Heat can
cause an increase in air
pressure resulting in an
explosion. Welding can
structurally weaken or deform
the wheel.
• Do not stand in front or over
the tire assembly when
inflating. Use a clip-on chuck
and extension hose long
enough to allow you to stand
to one side.
Check Engine Crankcase Oil
IMPORTANT: Engine is shipped with 5W-30
oil in crankcase. Refer to Engine Manual for
detailed instructions.
Fill Engine Fuel Tank
Refer to Engine Manual for proper fuel type
and tank capacity. Refer to FILLING FUEL
TANK on page 13.
Check Function of all Controls
Ensure unit runs and performs properly. Refer
to Operation on page 11.
Run-in Attachment Belt
1. Start unit in a well-ventilated area
according to Starting and Shut Off on
page 14.
2. Engage attachment clutch lever and run
attachment for about 15 minutes.
3. Stop unit, wait for all moving parts to
stop, and remove spark plug wire.
4. Adjust clutch idler according to
Attachment Clutch Adjustment on
page 21.
5. Adjust belt finger, if necessary. See
Check Belt Finger Clearance on
page 22.
EN - 9
Page 10
Figure 4
1
2
3
4
9
11
10
5
16
6
13
12
14
7
17
18
15
8
CONTROLS AND FEATURES
1. Traction Drive Clutch Lever
2. Speed Selector Lever
3. Attachment Clutch Lever
4. Brush Angle Lock Lever
5. Recoil Starter Handle
6. Engine Shut Off Switch
7. Engine Throttle
8. Oil Fill/Dipstick
9. Brush Guard
10. Brush
11.Height Adjustment Wheels
12. Fuel Shut Off Valv e
13. Fuel Fill Cap
14. Choke
15. Oil Drain Plug
16. Electric Start Push Button
17. Muffler
18. Air Filter
EN - 10
Page 11
OPERATION
1
2
1
2
ON
OFF
Figure 5
Dual Handle Interlock
WARNING: AVOID INJURY . Read
and understand the entire Safety
section before proceeding.
WARNING: To avoid injury to
hands and feet, always disengage
clutches, shut off engine, and wait
for all movement to stop before
unclogging or working on brush.
Keep hands and feet away from
brush.
STANDARD CONTROLS
See Controls and Features on page 10.
Traction Drive Cl utch Left Hand Lever
Squeeze the Traction
Drive Clutch Lever
against the handlebar
(1) to engage wheel
drive for propelling unit.
Release lever (2) to
stop movement.
IMPORTANT: When traveling to or from an
area to be cleared, press down on the
handlebars enough to raise the front of the
unit slightly off the surface. Engage the
traction drive clutch without engaging the
attachment drive clutch.
NOTE: Traction drive clutch should be
engaged before the attachment clutch when
brushing.
Attachment Drive Clutch - Right Hand
Lever
Squeeze Attachment Clutch
Lever against handlebar (1) to
engage attachment. Release
both clutch levers (2) to
disengage power to
attachment.
IMPORTANT: If the bel t
squeals when the attachment
clutch lever is engaged, the
attachment drive may be
frozen. Immediately release
the attachment clutch lever
and move the unit into a
heated area to thaw.
NOTE: If belt squeals when brush runs freely ,
(see Attachment Clutch Adjustment on
page 21).
When Attachment Clutch and then Traction
Drive Clutch are engaged, the Attachment
Clutch Lever will remain engaged (down) if
released. To stop attachment, release
Traction Drive Clutch Lever and both clutches
will disengage.
Choke Control Lever
1.Choke Closed position (lever
to left): chokes off air to engine
for easier start.
2.Choke Open position (lever to
right): allows for normal
operation.
Gradually open choke after
engine starts.
Engine Shut-Off Switch
(Figure 5)
1. Set the engine shut off switch to the On
position to start and operate the engine.
2. Set the engine shut off switch to the Off
position to shut off a running engine.
EN - 11
Page 12
Throttle Lever
12 3
6
1
1
2
Open Position: Use
this position to run the
unit.
Closed Position: Use
this position to service,
transport, or store the
unit.
Brush Position Locked
Brush Position Unlocked
The throttle controls the engine speed. To
increase or decrease engine speed, adjust to:
1. Fast (normal or warm starts) to left
2. Part-Throttle at center
3. Slow (cold weather starts) to right
Electric Starter
The electric starter will start a properly
choked engine when the starter button is
pushed. Refer to Starting and Shut Off on
page 14.
Recoil Starter Handle
When pulled, handle will turn engine over.
IMPORTANT: DO NOT let handle snap back
against starter.
NOTE: When operating unit in the winter
months recoil guard foam cover must be
installed. See Recoil Guard Foam Cover
Installation on page 20.
Speed Selector Lever
Position lever in the appropriate notch to
control speed of forward and reverse travel.
Fuel Shut-Off Valve
IMPORTANT: The fuel shut-off valve MUST
be in the closed position prior to transporting
the unit.
The fuel shut-off valve has two positions:
BRUSH ANGLE ADJUSTMENT
Brush can be positioned either straight ahead
or angled 20º to either right or left. To change
the angle of the brush:
1. Release both clutch levers and wait for
all moving parts to come to a complete
stop.
2. Pull up on the Brush Angle Lock Lever
and hold. This will release the cableoperated lock pin.
FORWARD
(6) Fastest
(1) Slowest
IMPORTANT: DO NOT
change motion from
forward to reverse with
clutch engaged.
Forward or reverse speed
can be changed without
de-clutching.
REVERSE
(1) Slow
(2) Fast
:
:
3. With the brush assembly resting on
ground, push/pull on handlebars to
rotate brush right or left.
4. With brush in the desired position,
release Brush Angle Lock Lever to lock
brush in position.
BRUSH HEIGHT ADJUSTMENT
IMPORTANT: If brush height is set too low,
brush can drive machine rearward when
attachment clutch is engaged. Engage brush
slowly with brush set at proper height.
The brush works best with the brush properly
leveled. To adjust the brush height:
1. Move the brush to a dusty, flat surface.
Leave the engine running.
2. Start the brush at a slow speed. Run the
brush in a stationary position for 30
seconds.
EN - 12
Page 13
3. Lift the brush head assembly off the
Figure 6
1.Caster Wheel
2.Brush Height Spacers
1
2
2 – 3 in. (5.08 – 7.6 cm)
Swept Area
ground and reverse the unit to move it
away from the swept area.
4. Stop engine and allow all moving parts
to stop.
5. Check the width of the swept area. The
brush pattern should be 2 – 3 inches
(5.08 – 7.6 cm) wide, running the length
of the brush (Figure 6).
6. To adjust, remove the lock pin from the
top of the caster fork. Raise the caster
arm high enough to expose the flats and
lower pin hole on the caster fork spindle.
Insert the lock pin into the lower hole to
support the arm while adjusting the
brush height spacers (Figure 6).
7. Align the open ends of the spacers with
the flats on the caster spindle and
remove the spacers one at a time until
enough are left at the bottom for the
desired brush height.
8. Remove the lock pin while supporting
the caster arm. Lower the arm on top of
the remaining spacers. Put the spacers
that were removed in the caster spindle
above the support tube as shown
(Figure 6).
9. Reinstall the lock pin into the top hole
and flip over the lock ring to secure the
remaining spacers and pin.
10. Repeat steps 1 – 10 until proper
adjustment is attained.
NOTE: Set both wheels at the same height
for a level brush.
FILLING FUEL TANK
WARNING: AVOID INJURY. Read
and understand the entire Safety
section before proceeding.
GASOLINE
IMPORTANT: ALWAYS use gasoline that
meets the following guidelines:
• Clean, fresh gasoline.
• A minimum of 87 octane/87 AKI (91
RON). High altitude use may require a
different octane. Consult your engine
manual.
• Gasoline with up to 10% ethanol
(gasohol) or up to 10% MTBE (methyl
tertiary butyl ether) is acceptable.
• Use of any gasoline other than those
approved above will void the engine
warranty. If the pumps are not marked
for the content of alcohol or ethers,
check ethanol and MTBE levels with
the fuel supplier.
• Do not modify the fuel system to use
different fuels.
• Never mix oil and gasoline.
NOTE: All gasoline is not the same. If the
engine experiences starting or performance
problems after using a new gasoline, switch
to a different fuel provider or fuel brand.
IMPORTANT: Excessively oxygenated or
reformulated fuels (fuels blended with
alcohols or ethers) can damage the fuel
system or cause performance problems. If
any undesirable operating problems occur,
use a gasoline with a lower percentage of
alcohol or ether.
Add Fuel to Fuel Tank
WARNING: FLAMMABLE FUEL
and its EXPLOSIVE VAPORS
can result in death or serious
injury. Handle fuel with extreme
care. ALWAYS use an approved
fuel container. NO Smoking! NO
Lighted Materials! No Open
Flames! Allow engine to cool
before any service.
1. ALWAYS place unit in open or wellventilated area.
2. Stop engine and allow to cool.
3. Clean Fuel Cap and surrounding area to
prevent dust, dirt and debris from
entering Fuel T ank.
4. Remove fuel cap.
IMPORTANT: Refer to Engine Manual for
correct type and grade of fuel.
EN - 13
Page 14
5. Fill fuel tank to within 1/2 in (1.27 cm)
below bottom of filler neck. See
Specifications on page 29 for fuel tank
capacity.
IMPORTANT: DO NOT OVERFILL! This
equipment and/or its engine may include
evaporative emissions control system
components, required to meet EPA and/or
CARB regulations, that will only function
properly when the fuel tank has been filled to
the recommended level. Overfilling may
cause permanent damage to evaporative
emissions control system components. Filling
to the recommended level ensures a vapor
gap required to allow for fuel expansion. Pay
close attention while filling the fuel tank to
ensure that the recommended fuel level
inside the tank is not exceeded. Use a
portable gasoline container with an
appropriately sized dispensing spout when
filling the tank. Do not use a funnel or other
device that obstructs the view of the tank
filling process.
6. Replace fuel cap and tighten.
7. ALWAYS clean up spilled fuel.
Fuel Stabilizer
IMPORTANT: Fuel st abilizer is recommended
for extended storage (see Add Fuel Stabilizer
on page 27).
Gasoline left in the fuel system for extended
periods without a stabilizer will deteriorate,
resulting in gum deposits in the system.
These deposits can damage the carburetor
and the fuel hoses, filter and tank. Prevent
deposits from forming in the fuel system
during storage by adding a quality fuel
stabilizer to the fuel. Follow the
recommended mix ratio found on the fuel
stabilizer container.
PRE-START
1.Check Function of Clutches
Brush must stop quickly when attachment
clutch lever is released.
Wheels must stop quickly when traction
clutch lever is released.
If clutches do not engage or disengage
properly, adjust or repair before operation
See Attachment Clutch Adjustment on
page 21 and Traction Drive Clutch
Adjustment on page 23.
2.Check Dual Handle Interlock
Without the engine running, press down
(engage) both clutch levers. Release
attachment clutch lever. Attachment clutch
should remain engaged until traction clutch
lever is released, then both clutches must
disengage.
If clutches do not engage or disengage
properly, adjust or repair before operation
See Attachment Clutch Adjustment on
page 21. and Traction Drive Clutch
Adjustment on page 23.
3.Adjust Brush
Adjust brush height and angle before
operation. See Brush Angle Adjustment on
page 12 and Brush Height Adjustment on
page 12.
4.Check Engine Fuel and Crankcase
Oil Levels
WARNING: AVOID INJURY . Read
and understand the entire Safety
section before proceeding.
Check and add fuel if required. Check that
the engine crankcase oil is full using dipstick.
Refer to Engine Manual for detailed
instructions.
TO STOP IN AN EMERGENCY
Immediately release both control levers to
stop unit in an emergency. Stop engine and
wait for all rotating parts to stop before
leaving operator’s position.
STARTING AND SHUT OFF
WARNING: FAILURE TO FOLLOW
INSTRUCTIONS could result in
personal injury and/or damage to
unit. DO NOT attempt to start you r
unit at this time. Read entire
Owner/Operator Manual and the
Engine Manual first.
IMPORTANT: At start-up, allow unit and
engine to adjust to the outside temperature
before operating. Before shut-off, run unit a
few minutes to prevent freeze-up.
NOTE: Try out each control without the
engine running to see how they work and
what they do.
Manual Start
1. Make sure that traction clutch lever and
attachment clutch lever are fully
disengaged.
2. Turn engine shut-off switch to “ON”
position.
3. If engine is cold, apply choke. A warm
engine requires less choking than a cold
engine. See Engine Manual for detailed
instructions.
4. Set throttle to proper starting position.
EN - 14
Page 15
5. Pull recoil starter handle with a rapid
continuous full arm stroke. Let rope
rewind slowly.
IMPORTANT: DO NOT let Starter Handle
snap against Starter.
NOTE: When operating unit in the winter
months, recoil guard foam cover must be
installed. See Recoil Guard Foam Cover
Installation on page 20.
6. Repeat until engine starts. (If engine
does not start, refer to Troubleshooting
on page 28.)
7. Adjust choke as needed.
8. Set throttle to Part Throttle or Slow
position to adapt to outside temperature
or travel speed. Set throttle to Fast
position for normal operation.
Electric Start (120V)
1. Connect extension cord to starter.
IMPORTANT: Prevent damage to unit. Know
voltage of your starter and only use matching
outlets.
2. Plug extension cord into 120V, 3-wire,
grounded outlet.
IMPORTANT: Use only Ariens extension cord
(P/N 02483100) or an equivalent cord that is
rated for a minimum of 13 amps, grounded,
UL listed, CSA certified and labeled as
suitable for outdoor use.
3. Make sure that traction clutch lever and
attachment clutch lever are fully
disengaged.
4. Turn engine shut-off switch to “ON”
position.
5. If engine is cold, apply choke. A warm
engine requires less choking than a cold
engine. See Engine Manual for detailed
instructions.
6. Set throttle to proper starting position.
7. Press starter button on engine until
engine starts.
IMPORTANT: DO NOT operate starter more
than 15 seconds per minute, as overheating
and damage can occur. (If engine does not
start, refer to Troubleshooting on page 28.)
8. Adjust choke as needed.
9. Disconnect power cord from outlet, then
starter.
10. Set throttle to Part Throttle or Slow
position to adapt to outside temperature
or travel speed. Set throttle to Fast
position for normal operation.
Shut Off
1. Release both clutch levers and wait for
all moving parts to come to a complete
stop.
2. Run unit a few minutes after use to
prevent freeze-up.
3. Move throttle to STOP position.
4. Turn engine shut-off switch to “OFF”
position.
USING THE BRUSH
After proper Pre-Start and Starting:
1. Select speed control position and
direction.
IMPORTANT: DO NOT overload unit capacity
by sweeping at too fast a rate.
2. Engage the traction drive clutch first.
3. Engage the attachment clutch next.
Tips for Sweeping
To clear an area, run unit in an overlapping
series of paths. For large areas, start in the
middle and sweep debris to each side, so it is
not cleared more than once.
ALWAYS direct discharge away from area to
be cleared and with direction of the wind.
Snow is best removed as soon as possible
after snow fall.
Tips for De-thatching
De-thatch in the spring to clear winter
undergrowth.
Adjust brush height so it just touches the
grass.
Set the brush angle full left or full right so
thatch gets cleared only once.
De-thatch dry grass.
Use a slow speed to clear thatch without
damaging the lawn.
TRAVELING
To travel from one work area to another:
1. Set throttle to SLOW position or slightly
higher.
2. Press down the handlebars enough to
raise the front of the unit slightly off the
surface.
3. Engage traction clutch without engaging
the attachment drive clutch.
TRANSPORT
ALWAYS shut off engine and close fuel shutoff when transporting unit on a truck or trailer.
Use extra care when loading or unloading
unit onto trailer or truck.
Secure unit chassis to transport vehicle.
NEVER secure from rods or linkages that
could be damaged.
DO NOT transport machine while engine is
running.
EN - 15
Page 16
MAINTENANCE
Figure 7
1
2
7
6
544
3
1.Belt Cover
2.Bottom Cover Rear Cap Screws
3.Bottom Cover
4.Bottom Cover Side Cap Screws
5.Pivot Rod
6.Brush Frame Adapter
7.Brush Frame Adapter Mounting Cap Screws
Ariens Dealers will provide any service or
adjustments which may be required to keep
your unit operating at peak efficiency. Should
engine service be required, contact a Ariens
dealer or an authorized engine
manufacturer's service center.
WARNING: AVOID INJURY . Read
and understand the entire Safety
section before proceeding.
2. Remove belt cover.
3. Remove hardware attaching remote
trigger cable to brush assembly and
detach cable.
4. Remove six cap screws securing bottom
cover of traction unit and remove cover.
5. Remove cap screws and belt finger.
6. Remove attachment drive belts from
engine sheave (it may be necessary to
turn engine sheave using recoil starter
handle).
SERVICE POSITION
(Figure 7)
WARNING: ALWAYS remove key
and/or wire from spark plug before
assembly, maintenance or
service. Unintentional engine start
up can cause death or serious
injury.
IMPORTANT: DO NOT tip unit up onto brush.
Remove the brush if maintenance requires
tipping the unit forward. Ensure unit is secure
and will not tip over. Strap or clamp unit onto
bench if required.
To separate the brush attachment from
traction unit:
1. Shut off engine, close fuel shut-off valve,
disconnect spark plug wire and allow
unit to cool completely. Place unit on a
flat level surface.
CAUTION: Always support unit
frame and brush attachment when
loosening the cap screws holding
them together.
7. Remove cap screws securing brush
attachment to traction unit (one on each
side at top).
8. Tip traction unit back so that it comes
apart from brush attachment.
9. While brush attachment is supported on
traction unit lower pivot rod, remove
attachment drive belts from attachment
pulley.
10. Separate brush attachment from traction
unit.
EN - 16
Page 17
OPERATING POSITION
(Figure 7)
To connect the brush attachment to traction
unit:
1. Place attachment belts onto attachment
pulley.
NOTE: Holding down the attachment clutch
lever will make it easier to reconnect the
brush attachment to traction unit.
2. Tip traction unit back while guiding brush
attachment up and onto lower pivot rod.
3. Tilt traction unit back up level to bring it
together with brush attachment.
4. Install cap screws (one on each side at
top) to secure brush attachment to
traction unit.
5. Place attachment drive belts onto engine
sheave. It may be necessary to turn
engine sheave using recoil starter
handle (Figure 12).
6. Reinstall belt finger. Check belt finger
clearance (See Check Belt Finger
Clearance on page 22).
IMPORTANT: DO NOT bend belt finger out of
shape.
7. Install bottom cover with six cap screw s.
8. Install belt cover.
9. Reinstall remote trigger cable to brush
assembly.
MAINTENANCE SCHEDULE
The chart below shows the recommended
maintenance schedule that should be
performed on a regular basis. More frequent
service may be required due to working
conditions (heavy loads, high ambient
temperatures, dusty conditions, or airborne
debris).
MAINTENANCE SCHEDULE
Yearly
Service
Performed
Check Dual
Handle
Interlock
Check
Fasteners
Check
Clutch
Operation
Clean
Engine
Clean Recoil
Guard Foam
Cover
Check
Engine Oil
General
Lubrication
Check
Clutch Cable
Adjustments
Check Tire
Pressure
Change
Engine Oil
Each
Daily
Use
•
•
•
•
•
(8 hrs.)
Every
25 hrs
•
•
**
* After first 5 hours of operation.
** Refer to Engine Manual for detailed
instructions.
CHECK DUAL HANDLE
INTERLOCK
Without the engine running, press down
(engage) both clutch levers. Release
attachment clutch lever. Attachment clutch
should remain engaged until traction clutch
lever is released, then both clutches must
disengage.
or
100
hrs
*•
•
CHECK FASTENERS
Make sure all hardware is tightened properly.
EN - 17
Page 18
CHECK CLUTCH OPERATION
Brush must stop quickly when attachment
clutch lever is released.
Wheels must stop quickly when traction drive
clutch lever is released.
If clutches do not engage or disengage
properly, adjust or repair before operation
(seeAttachment Clutch Adjustment on
page 21 and Traction Drive Clutch
Adjustment on page 23).
CHECK CLUTCH CABLE
ADJUSTMENT
Make sure the attachment clutch and traction
drive clutch are adjusted as specified in
Attachment Clutch Adjustment on page 21
and Traction Drive Clutch Adjustment on
page 23.
CLEAN ENGINE
Refer to Engine Manual for detailed
instructions.
CLEAN RECOIL GUARD FOAM
COVER
Make sure the recoil guard foam cover is
always kept clean and free of snow and
debris.
If cover becomes clogged with debris gently
vacuum the foam or wash with warm water.
NOTE: Cover is not necessary for operation
during the non-winter months.
If cover is clogged with snow remove it
immediately and allow foam to thaw or rinse
with warm water.
IMPORTANT: Allow foa m to dry completely
before reinstallation.
See Recoil Guard Foam Cover Installation on
page 20.
CHECK ENGINE OIL
The engine crankcase oil should be checked
every 8 hours of operation. Oil level MUST be
maintained in safe operating range on
dipstick at all times or engine damage will
result (See Engine Manual).
Park unit on a level surface. Refer to Engine
Manual for detailed instructions.
CHANGE ENGINE OIL
Refer to Engine Manual for detailed
instructions.
CHECK TIRE PRESSURE
CAUTION: A void injury! Explosive
separation of tire and rim parts is
possible when they are serviced
incorrectly:
• Do not attempt to mount a tire
without the proper equipment
and experience to perform the
job.
• Do not inflate the tires above the
recommended pressure.
• Do not weld or heat a wheel and
tire assembly. Heat can cause
an increase in air pressure
resulting in an explosion.
Welding can structurally weaken
or deform the wheel.
• Do not stand in front or over the
tire assembly when inflating.
Use a clip-on chuck and
extension hose long enough to
allow you to stand to one side.
Check tire pressure and adjust to the
pressure listed on tire sidewall.
EN - 18
Page 19
GENERAL LUBRICATION
Figure 8
OS0743
Oil
Grease
(Figure 8)
1. Place unit into the service position (See
Service Pos i tion on page 16).
IMPORTANT: Wipe each fitting clean before
and after lubrication. DO NOT allow grease or
oil to get on friction disc, friction plate or belts.
2. Apply Hi-Temp Grease or equivalent to
the lubrication fittings after the first 16
hours of use and every 8 hours
thereafter. See Service Parts on
page 28.
3. Apply a few drops of oil to the roller
chain at the beginning of the season or
every 25 operating hours.
NOTE: Brush attachment gear case is
lubricated at the factory and should not
require additional lubrication.
4. Place unit into the operating position
(See Operating Position on page 17).
EN - 19
Page 20
SERVICE AND ADJUSTMENTS
Figure 9
2
1
3
1.Recoil Guard Foam Cover
2.Velcro
®
3.Recoil Guard
WARNING: AVOID INJURY.
Read and understand the entire
Safety section before
proceeding.
RECOIL GUARD FOAM COVER
INSTALLATION
(Figure 9)
The recoil foam cover slides over the starter
handle and attaches to the recoil guard with
Velcro®.
NOTE: The recoil guard foam cover is not
necessary for operation during the non-winter
months.
IMPORTANT: When using the unit in the
winter months the cover must be installed.
The foam prevents snow from getting into the
recoil guard and freezing the recoil pawls.
IMPORTANT: Be sure to keep the recoil foam
cover clean and clear of snow and debris at
all times. See Clean Recoil Guard Foam
Cover on page 18.
SPEED SELECTOR
ADJUSTMENT
(Figure 8)
To adjust:
1. Disconnect adjustment pivot pin from
speed selector lever.
2. Place the speed selector in the fastest
forward speed position.
3. Turn the speed selector lever straight
down towards the ground as far as it will
go.
4. Thread the adjustment pivot pin along
the shift rod until it aligns with the mating
hole on the speed selector lever. Insert
the pivot pin into hole.
5. Secure adjustment pivot pin with hairpin.
6. Make sure the speed selector shifts into
each speed position.
7. Check forward and reverse speeds:
a. Start unit.
b. Shift speed selector into the first
forward speed.
c. Engage the traction clutch. Unit
should move forward.
d. Stop unit.
e. Shift speed selector into first
reverse speed.
f. Engage the traction clutch. Unit
should move backward.
g. Shut off unit.
8. Adjust pivot pin on the shift rod as
necessary so unit travels forward when
speed selector is in first forward position
and travels backward when speed
selector is in first reverse position.
9. Connect the pivot pin to the speed
selector arm with the hardware removed
in step 1.
EN - 20
Page 21
ATTACHMENT CLUTCH
Figure 10
2
3
1
4
1.Shift Rod
2.Adjustment Pivot Pin
3.Speed Selector Lever
4.Hairpin
Figure 11
1.Attachment Clutch Cable
2.Adjustment Barrel
3.Jam Nut
2
3
OS7185
1
OS7191
Figure 12
OS7196
With the attachment clutch
DISENGAGED, check the attachment
idler arm position here. The attachment
idler arm should lightly touch the frame.
4
5
2
3
1
1.Engine Sheave
2. Attachment Drive Belts
3.Idler Pulley Adjustment Nut
4.Idler Arm
5.Frame
ADJUSTMENT
(Figures 11, 12 and 13)
WARNING: IMPROPER
ADJUSTMENT could result in
unexpected movement of brush
causing death or serious injury.
BRUSH MUST STOP within 5
seconds when Attachment Clutch
Lever is released.
3. With the attachment clutch disengaged,
check that the attachment idler arm
lightly touches the frame (Figure 12).
4. Tighten jam nut on the adjustment barrel
(Figure 11).
requires the engine to be run with
the belt cover off. AVOID INJURY.
Read and understand the entire
Safety section before proceeding.
Remove Attachment Cable Slack
WARNING: Adjustment procedure
1. Remove the belt cover.
2. Loosen jam nut on cable adjustment
barrel, and then turn the adjustment
barrel down to shorten cable and
remove all cable slack (Figure 1 1).
EN - 21
Page 22
Check Attachment Idler Arm
Figure 13
Some components removed for
clarity of illustration.
Roller should be 1/2 – 7/8 in. (13 – 22 mm)
from the frame when the attachment clutch
is ENGAGED.
2
3
4
1
1.Frame
2.Idler Adjustment Nut
3.Attachment Idler Arm
4.Roller
Roller Clearance
(Figure 13)
NOTE: It will be difficult to check the
measurement inside the frame. Use a 1/2 in.
(12.7 mm) minimum spacer as a gauge to
check the clearance between the roller and
the frame.
1. Remove bottom cover.
2. With the attachment clutch lever
engaged, check the clearance between
the frame and plastic roller on the lower
end of the attachment idler arm
(Figure 13).
• If roller is 1/2 – 7/8 in. (12.7 –
22.2 mm) from frame, no further
adjustment is required.
• If roller is less than 1/2 in. (12.7 mm)
from frame, loosen idler adjustment
nut and move idler closer to the belt.
Tighten adjustment nut and recheck
the roller clearance.
• If roller is more than 7/8 in. (22.2 mm)
from frame, loosen idler adjustment
nut and move idler away from the belt.
Tighten adjustment nut and recheck
roller clearance.
Check Belt Finger Clearance
1. With attachment clutch lever engaged,
the belt finger located opposite the belt
idler must be less than 1/8 in. (3 mm)
from belts, but not touching the belts
(Figure 14).
2. Remove the belt cover.
3. To adjust belt finger , loosen the bolts and
move the finger to the proper position.
Tighten the bolts and recheck the belt
finger clearance.
4. Replace the belt cover.
EN - 22
Page 23
TRACTION DRIVE CLUTCH
Figure 14
Check belt finger clearance here. With the
attachment clutch engaged, there should
be less than 1/8 in. (3 mm) clearance
between the belts and the belt finger. The
belt finger should not touch the belts.
1. Mounting Hardware
2. Belt Finger
1
2
Figure 15
1.T r action Drive Belt
2.Engine Sheave
3.Attachment Drive Belts
4.Belt Finger
5.Attachment Belts Idler
6.Attachment Pulley
7.Attachment Idler Adjustment Nut
8.T r action Belt Idler
9.T r action Drive Pulley
10.Drive Plate Assembly Stop Screw
1
2
3
4
5
8
9
6
Some components removed for clarity
of illustration.
7
10
ADJUSTMENT
(Figure 15)
If drive slips, adjust traction clutch to
compensate for friction disc wear.
To adjust traction clutch:
1. Loosen jam nut on traction cable
adjustment barrel. Turn the adjustment
barrel down to shorten cable and
remove all cable slack.
2. With the traction clutch disengaged
check that the drive plate assembly
lightly touches to stop screw inside the
frame (Figure 15).
ATTACHMENT DRIVE BELTS
REPLACEMENT
WARNING: ALWAYS remove
key and-or wire from spark plug
before assembly, maintenance
or service. Unintentional engine
start up can cause death or
serious injury.
1. Place the unit into the service position
(See Service Position on page 16).
2. Using new attachment drive belts , place
unit into the operating position (See
Operating Position on page 17).
TRACTION DRIVE BELT
REPLACEMENT
(Figure 15 and 16)
1. Remove attachment drive belts (See
Attachment Drive Belts Replacement on
page 23).
NOTE: Make sure the drive plate assembly
return spring remains connected to the frame.
EN - 23
Page 24
2. To gain belt clearance, back out the stop
Figure 16
1.Attachment Drive Belts Idler
2.Traction Drive Belt Idler
3.Engine Sheave
3
2
1
screw from the frame until the drive plate
assembly can swing past it (Figure 15).
3. Pull idler away from traction drive belt
and remove belt from engine sheave. It
may be necessary to turn engine pulley
using recoil handle (Figure 16).
4. Remove traction drive belt from drive
plate assembly pulley (Figure 17).
5. Install new traction drive belt onto drive
plate assembly pulley and engine
sheave.
6. Pull the drive plate assembly toward the
friction disc and turn stop screw all the
way in.
7. Replace attachment drive belts (see
Attachment Drive Belts Replacement on
page 23).
FRICTION DISC REPLACEMENT
(Figure 17)
1. Place the unit into the service position
(See Service Position on page 16).
2. With axle locked, hold one wheel/tire so
friction disc will not rotate and remove
three self-tapping screws holding friction
disc to carrier.
3. Remove both wheel/tires.
4. Remove two spring clip pins from hex
shaft.
NOTE: Bearings are retained by flanges.
5. Remove right and left bearing flanges
from frame.
6. Slide hex shaft to the left enough to
remove pinion sprocket from hex shaft.
NOTE: Outside bearing will fall free from hex
shaft.
7. Slide hex shaft to the right enough to
remove friction disc.
8. Slide new friction disc onto hex shaft.
9. Slide hex shaft to the left and install
pinion sprocket and chain on hex shaft.
10. Slide hex shaft to the right until centered
in frame and install bearings on shaft
ends and retain with bearing flanges.
11.Install both wheel/tires.
12. Hold wheel/tire so friction disc will not
rotate and secure new friction disc to
carrier with three self-tapping screws.
13. Place unit into the operating position
(See Operating Position on page 17).
14. Adjust traction drive clutch (See Traction
Drive Clutch Adjustment on page 23).
EN - 24
Page 25
Figure 17
OS7225
1.Friction Disc
2.Self-Tapping Screws
3.Carrier
4.Spring Clip Pin
5.Hex Shaft
6.Bearing Flange
7.Pinion Sprocket
8.Drive Plate Assembly
9.Chain
10.Bottom Cover Rear Cap Screws
11.Bottom Cover Side Cap Screws
12.Drive Plate Assembly Stop Screw
2
3
6
5
1
7
4
9
11
12
8
10
10
11
Figure 18
1.Nyloc Nut
2.End Plate
3.Flanged Bearing
4.Brush End Support
1
1
4
3
2
BRUSH SEGMENT
REPLACEMENT
(Figure 18, 19, and 20)
WARNING: ALWAYS remove key
and/or wire from spark plug before
assembly, maintenance or
service. Unintentional engine start
up can cause death or serious
injury.
1. Shut off engine, close fuel shut-off valve,
disconnect spark plug wire and allow
unit to cool completely. Place unit on a
flat level surface.
2. Remove two nyloc nuts and round head
square neck bolts securing flanged
bearing to horizontal end support at
each side of brush (Figure 18).
EN - 25
Page 26
3. Loosen each bearing setscrew and slide
Figure 19
2
3
1.Brush Segment
2.U-Joint
3.Splined Shaft
4.Gearbox
1
4
Figure 20
5
4
3
2
1.Flanged Bolts
2.Engagement Fingers
3.Support Shaft Assembly
4.Brush Segment
5.End Plate
1
bearings inward, away from horizontal
end supports.
IMPORTANT: Brush gearbox splined shaft
will separate from brush housing u-joint.
Support splined shaft to prevent damage
(Figure 19).
4. Manually move traction unit backwards,
pulling brush housing away from brush
assembly.
NOTE: The gearbox at the center of the
brush allows only half the brush segments to
be removed from each end.
5. Stand brush assembly upright on one
end.
6. Remove three flanged bolts securing
end plate to support shaft assembly.
Remove the end plate (Figure 20).
EN - 26
Page 27
IMPORTANT: Brush segments must be
aligned properly so they do not nest together
(Figure 19).
7. Remove used brush segments and
replace with new segments.
IMPORTANT: For each brush segment, align
the pair of engagement fingers on alternating
support shafts. This will evenly spread the
rotating force throughout the support shaft
assembly.
8. Install end plate on support shaft
assembly and secure with three flanged
head bolts (Figure 20).
9. Position brush back down horizontally.
10. Repeat steps 5 through 8 to replace
segments for opposite end of brush.
11. Manually move traction unit forward
while guiding brush gearbox splined
shaft into brush housing u-joint.
12. Slide brush shaft bearings outward,
against brush housing. Tighten each
bearing setscrew to lock it in place on
center shaft.
13. Install two round head square neck bolts
and nyloc nuts to secure each flanged
bearing to the brush housing
(Figure 18).
STORAGE
WARNING: AVOID INJURY. Read
and understand the entire Safety
section before proceeding.
FUEL SYSTEM
Gasoline left in the fuel system for extended
periods without a stabilizer will deteriorate,
resulting in gum deposits in the system.
These deposits can damage the carburetor
and the fuel hoses, filter and tank. Prevent
deposits from forming in the fuel system
during storage by adding a quality fuel
stabilizer to the fuel. Follow the
recommended mix ratio found on the fuel
stabilizer container.
IMPORTANT: NEVER store the engine with
fuel in the fuel tank inside of a building with
potential sources of ignition.
Add Fuel Stabilizer
1. Turn the fuel valve off while engine is
running and allow the engine to run until
it stops. Turn engine OFF when it begins
surging to avoid engine damage.
2. Add fuel stabilizer, following the
manufacturer’s instructions.
3. Turn fuel valve on after adding fuel
stabilizer.
4. Re-start engine.
5. Run the engine outdoors for 5 minutes to
be sure that treated gasoline has
replaced the untreated gasoline in the
carburetor.
6. Slow the engine to an idle speed.
SHORT TERM
IMPORTANT: NEVER spray unit with high-
pressure water or store unit outdoors.
Run unit a few minutes after each use to free
unit of any debris.
Inspect unit for visible signs of wear,
breakage or damage.
Keep all nuts, bolts and screws properly
tightened and know unit is in safe working
condition.
Close fuel shut-off valve.
Store unit in a cool, dry protected area.
LONG TERM
Clean unit thoroughly with mild soap and low
pressure water and lubricate (See
Maintenance on page 16). Touch up all
scratched painted surfaces.
Remove weight from wheels by putting
blocks under frame or axle.
EN - 27
Page 28
TROUBLESHOOTING
PROBLEM PROBABLE CAUSE CORRECTION
Engine will
not
crank/start.
Engine stops.
Engine
problems.
Does not
operate in
Forward/
Reverse.
Small ru bb er
beads collect
in frame
U-joint is
noisy
1. Fuel tank is empty.
2. Fuel shut-off valve
closed.
3. Engine shut off switch
turned off.
4. Engine ignition
problems.
5. Recoil pawls frozen.
1. Out of fuel.
2. Mechanical jam in
brush.
3. Polluted fuel supply.
4. Faulty spark plug.
1. See Engine Manual. 1. See Engine Manual.
1. Friction disc not
adjusted properly.
2. Traction belt not
functioning.
1. Friction disc wear. 1. Normal friction disc wear. Chunks or
1. Friction.
2. Wear.
1. Fill fuel tank.
2. Open fuel shut-off valve.
3. Turn on engine shut off switch.
4. See Engine Manual.
5. Remove snow and debris screen and
clean. See Clean Recoil Guard Foam
Cover on page 18. Bring unit into a warm
area and allow the recoil assembly to
thaw. Let recoil assembly dry completely
before operating the unit.
1. Fill fuel tank.
2. Turn off engine and wait for all moving
parts to stop. Check for and remove
obstruction and repair before restart.
3. Replace with clean fuel.
4. Replace or clean spark plug.
1. Repair or replace friction disc. See
Service and Adjustments on page 20.
2. Repair or replace traction drive belt. See
Service and Adjustments on page 20.
large pieces of rubber mean friction disc
should be checked and replaced as
necessary.
1. Lubricate u-joint.
2. Replace worn parts.
SERVICE PARTS
Order the following parts through your
Dealer:
Part No. Description
07231000 Traction Drive Belt
07200601 Attachment Drive Belt (Set of 2)
21547200 Spark Plug
00170800 Friction Disc
00036800 Ariens Hi-Temp Grease (Three
03972500 Recoil Guard Foam Cover
To obtain a complete parts manual, find your
model and serial number. Then go to
www.ariens.com.
EN - 28
3 oz. cartridges)
Page 29
SPECIFICATIONS
Model Number 926057
Engine Subaru EX27
Engine Displacement – in
Fast Idle Speed – RPM 3800 ±100
Starter 120VAC Electric and Recoil
Fuel See Engine Manual
Tank Capacity – qts. (L) 6.3 (6.1)
Clearing Width – in. (cm) 36 (91.44)
Brush Diameter – in. (cm) 25 (63.5)
Brush Rotation Speed – RPM 200
Drive (Traction Unit) Disc-O-Matic
Drive Speeds (Traction Unit) 6 Forward 2 Reverse
Pneumatic Tires – in 16 x 6.50-8
Brush Angle 40° Total (20° left/ right)
Size
Length – in (cm) 72 (183)
Hei ght – in ( cm) 43.0 (109.2)
Width – in (cm) 44.0 (111.8)
Weight – lbs. (kg) 325 (147.4)
3
(cc)
16.2 (265)
®
EN - 29
Page 30
Sno-Thro®, Sno-Tek® and
Chore Performing Equipment
Limited Warranty
Ariens Company (Ariens) warrants to the original purchaser that Ariens, Gravely, Parker, and Countax
brand chore performing equipment (including Sno-Thro
1/1/2013 will be free from defects in material and workmanship for the time period noted in the chart below.
Equipment put to personal use around a single household or residence is considered “Consumer Use”;
equipment put to any business use (agricultural, commercial, or industrial) or used at multiple locations is
considered “Commercial Use.” If any product is rented or leased, then the duration of these warranties shall
be 90 days after the date of purchase.
An authorized Ariens dealer (Ariens brand products), Gravely dealer (Gravely brand products), Parker dealer
(Parker brand products), or Countax dealer (Countax brand products) will repair any defect in material or
workmanship, and repair or replace any defective part, subject to the conditions, limitations and exclusions
set forth herein. Such repair or replacement will be free of charge (labor and parts) to the original purchaser
except as noted below.
Warranty
Code
PA Log Splitters, Brushes, String Trimmers, Edgers 3 Years 90 Days
PB Professional Powered Brushes 3 Years 1 Year
PC Tillers 2 Years 90 Days
Vacuums, Blowers, Sweepers, Truck Loaders,
PD
Lawn Rakes, Sprayers, Aerators, etc.
PE Pressure Washer, Generators 3 Years 1 Year
SA
Professional Sno-Thro
SB
Compact, Deluxe, Platinum, AMP™ Sno-Thro
SC
Sno-Tek
UA Utility Vehicles 1 Yea r 1 Year
N/A Service (Replacement) Parts 90 Days (no labor) 90 Days (no labor)
Product Group
®
®
®
and Sno-Tek® equipment) purchased on or after
Warranty Period
®
Consumer Use
1 Year 1 Year
3 Years 1 Year
3 Years 9 0 Days
2 Years 9 0 Days
Warranty Period
Commercial Use
Special Extensions
The chart below details special extensions to this warranty:
Warranty
Code
SA
SB
SB
Warranty Exception
Cast Iron Auger
Gear Case
Cast Iron Auger
Gear Case
Batteries for AMP™
®
Sno-Thro
Warranty
Period
5 Years All
5 Years Consumer
2 Years Consumer 100% first year; prorated second year.
Use Detail
5 Years for all users including
Commercial
5 Years for Consumer use;
1 Year for Commercial Use
Sno-Chore 2013EN - 30
Page 31
Exceptions and Limitations
The chart below details special exceptions to this warranty:
Warranty
Code
SA, SB,
Warranty Exception
All Batteries 1 Year All Prorated
All Belts, Muffler, Tires None Commercial
Cloth, Plastic, and
Rubber Components
All
(Including Belts and
Cables)
Idlers
SC
All Engines
Warranty
Period
Maximum
2 Years
Maximum
2 Years
See Engine
Manufacturer’s
Warranty
Use Detail
These components are not covered
when used commercially.
Warranty is limited to 2 years for
consumer use. (1 year fo r warranty
All
code "PD".) Except as noted above,
these components are covered for
defect, not for wear.
Warranty is limited on idlers to
All
2 years for consumer use.
Engines are covered by engine
manufacturer’s warranty. Refer to
All
engine manufacturer’s warranty
statement.
Customer Responsibilities
Register the product immediately at the time of sale. If the dealer does not register the product, the
customer must complete the product registration card in the literature package and return it to Ariens
Company, or register the unit online at www.ariens.com, www.gravely.com, www.countax.com or
www.parkersweeper.com.
To obtain warranty service, the original purchaser must:
• Perform the maintenance and adjustments explained in the Owner's Manual.
• Promptly notify Ariens or an authorized Ariens, Gravely, Parker or Countax service representative of
the need for warranty service.
• Transport the product to and from the place of warranty service at owner's expense.
• Have the warranty service performed by an authorized Ariens, Gravely, Parker or Countax service
representative.
To Find an Authorized Service Representative:
In the U.S. and Canada:
Use the dealer locator on our websites: www.ariens.com • www.gravely.com
Or contact us by mail or by phone:
In the U.S., Ca n a da , M ex i co , Ca r i bb ea n,
Central and South America:
Ariens Company
655 W. Ryan Street
Brillion, WI 54110
Phone: (920) 756 - 4688
www.ariens.com
In Europe, Asia, Africa or
the Middle East:
Countax Ltd, Countax House
Great Haseley, Oxfordshire,
OX44 7PF
Phone: 0800 597 7777
www.countax.com
In Australia or New Zealand:
Ariens Company
Building 2
6 Wedgewood Rd.
Hallam, Victoria 3803 Australia
Phone: (03) 9796 4244
1800 335 489
www.ariens.com.au
Sno-Chore 2013EN - 31
Page 32
Exclusions – Items Not Covered by This Warranty
• Parts that are not genuine Ariens, Gravely, Parker or Countax service parts are not covered by this
warranty and may void the warranty.
• Damages resulting from the installation or use of any part, accessory, or attachment which is not
approved by the Ariens Company for use with product(s) identified herein are not covered by this
warranty.
• The following maintenance, service and replacement items are not covered by this warranty unless
they are noted in the Limitations section above: lubricants, spark plugs, oil, oil filters, air filters, fuel
filters, brake linings, brake arms, brake shoes, skid shoes, scraper blades, shear bolts, mower
blades, mower vanes, brushes, headlights, light bulbs, knives, cutters, and single-stage impellers.
• Any misuse, alteration, improper assembly, improper adjustment, neglect, or accident which
requires repair is not covered by this warranty.
• Use of gasoline blends exceeding 10% ethanol voids any and all warranties.
• Products are designed to the specifications in the area that the product was originally distributed.
Different areas may have significantly different legal and design requirements. This warranty is limited to the requirements in the area in which the unit was originally distributed. Ariens Company
does not warrant this product to the requirements of any other area. Warranty service is limited to
service within the area originally distributed.
• In countries other than the United States and Canada, contact the Ariens Company dealer for war-
ranty policies that govern within your country. Rights may vary from country to country and within
any one country.
• Normal Wear: This warranty does not cover repair when normal use has exhausted the useful life of
a part such as a high pressure hose, spray wand, nozzles, trigger handle, supply hoses, quick couplers, gaskets, valves, pistons, pump valve assemblies, o-rings, water and oil seals.
Special Exclusions on Utility Vehicles
The following uses void the warranty terms on Utility Vehicles (Warranty Code UA):
• Renting or leasing the utility vehicle.
• Using the utility vehicle to tow or carry loads in excess of the limits specified in the Owner/Operator
Manual.
• Modifying the utility vehicle with parts and accessories that are not genuine or authorized Ariens or
Gravely parts or accessories.
• Modifying the utility vehicle without express written authorization from Ariens Company.
• Operating the utility vehicle when it has not been completely and properly assembled and
pre-delivered by an authorized Gravely dealer.
Disclaimer
Ariens Company may from time to time change the design of its products. Nothing contained in this warranty
shall be construed as obligating Ariens Company to incorporate such design changes into previously
manufactured products, nor shall such changes be construed as an admission that previous designs were
defective.
LIMITATION OF REMEDY AND DAMAGES
Ariens Company's liability under this warranty, and under any implied warranty that may exist, is limited to
repair of any defect in workmanship, and repair or replacement of any defective part. Ariens Company shall
not be liable for incidental, special, or consequential damages (including lost profits). Some states do not
allow the exclusion of incidental or consequential damages, so the above limitation or exclusion may not
apply to you.
AUSTRALIAN CONSUMER LAW
The following applies solely to warranties subject to Subsection 102(1) of the Australian Consumer Law: Our
goods come with guarantees that cannot be excluded by the Australian Consumer Law. You are entitled to a
replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or
damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable
quality and failure does not amount to a major failure.
DISCLAIMER OF FURTHER WARRANTY
Ariens Company makes no warranty, express or implied, other than what is expressly made in this
warranty. If the law of your state provides that an implied warranty of merchantability, or an implied
warranty of fitness for particular purpose, or any other implied warranty, applies to Ariens Company,
then any such implied warranty is limited to the duration of this warranty. Some states do not allow
limitations on how long an implied warranty lasts, so the above limitation may not apply to you.
This warranty gives you specific legal rights, and you may also have other rights which vary from region to region.
Sno-Chore 2013EN - 32
Page 33
Page 34
Ariens Company
655 West Ryan Street
Brillion, WI 54110
920-756-4688
Fax 920-756-2407
www.ariens.com
Loading...