Ariens 911094 - Pro 21SCH, 911095 - Pro 21CH, 911098 - LM21S, 911100 - LM21SW, 911394 - Pro 21SCH User Manual

Download

Page 1

Walk Behind Lawn Mower

Owner/Operator Manual

Models

911094 - Pro 21SCH 911095 - Pro 21CH 911098 - LM21S 911100 - LM21SW 911394 - Pro 21SCH

ENGLIS FRANÇAI ESPAÑO

Transfer model & serial number label from product registration here.

Coller l’autocollant du modèle et du numéro de série dans cet encadré.

Transferir aquí la etiqueta del modelo y número de serie del registro del producto.

01241000C 12/03

Supersedes 01241000, A, B

Printed in USA

Page 2

Ariens Company 655 West Ryan Street P.O. Box 157 Brillion, Wisconsin

54110-0157 USA Telephone (920) 756-2141 Facsimile (920) 756-2407

We the undersigned, ARIENS COMPANY, certify that:

Der Unterzeichnete, ARIENS COMP ANY, bescheinigt, dass: Wij, de ondergetekenden, ARIENS COMPANY, verklaren dat: Undertegnede, ARIENS COMPANY, attesterer, at: La sottoscritta società ARIENS COMPANY certifica che: Nosotros, los abajo firmantes, ARIENS COMPANY , certificamos que: Undertegnede, ARIENS COMPANY , bekrefter at: Undertecknad, ARIENS COMPANY, intygar att: Allekirjoittanut, ARIENS COMP ANY, vakuuttaa, että: My, nijej podpisani, ARIENS COMPANY, oświadczamy, że: Nós, abaixo assinados, certificamos em nome da ARIENS COMPANY, que:

EC DECLARA TION OF CONFORMITY ISSUED BY THE MANUF ACTURER – DÉCLARATION DE CONFORMITÉ CE ÉMISE PAR LE F ABR ICANT – EU-ÜBEREINSTIMMUNGSERKLÄRUNG DES HERSTELLERS – VERKLARING VAN OVEREENSTEMMING VOOR DE EU, AFGEGEVEN DOOR DE FABRIKANT – EF OVERENSSTEMMELSESERKLÆRING UDSTEDT AF FABRIKANTEN – DICHIARAZIONE DI CONFORMITÀ CE RILASCIAT A DAL PRODUTTORE – DECLARACIÓN DE CONFORMIDAD CE EMITIDA POR EL FABRICANTE – EF-SAMSVARSERKLÆRING FRA PRODUSENTEN – EG-DEKLARATIONEN OM ÖVERENSSTÄMMELSE UTFÄRDAD AV TILLVERKAREN – VALMISTAJAN ANTAMA EYVAATIMUSTENMUKAISUUSVAKUUTUS – DEKLARACJA ZGODNO PRZEPISAMI EC WYDANA PRZEZ PRODUCENTA – DECLARAÇÃO DE CONFORMIDADE CE EMITIDA PELO FABRICANTE –

Nous, soussignés ARIENS COMPANY, certifions que :

CI Z

Type: Type : Typ: Type: Type: Tipo:

Tipo: Type: Typ: Tyyppi: Typ: Tipo:

Trade Name:

Firmanavn: Nome commerciale: Nombre comercial: Handelsnavn: Handelsbeteckning: Kauppanimi: Nazwa handlowa: Nome da Marca:

Model:

Modèle : Modell: Model: Model: Modello: Modelo: Modell: Modell:

Malli: Model: Modelo: Cutting Width: Largeur de coupe : Schnittbreite: Maaibreedte: Klippebredde:

Larghezza di taglio: Ancho de corte: Klippebredde: Klippbredd: Leikkuuleveys: Szerokość cięcia: Largura de corte:

Conforms to:

overensstemmelse med: È conforme a: Cumple con: Er i samsvar med: Överensstämmer med: Täyttää seuraavat vaatimukset: Jest zgodny z: De acordo com:

Walk Behind Lawn Mower –

– Duwgrasmaaier – Selvkørende plæneklipper – Tosaerba semovente – Cortacésped de empuje manual – Gressklipper – Självgående gräsklippare – Käsinohjailtava ruohonleikkuri – Kosiarka trawnikowa – Cortador de Relva Convencional

Appellation commerciale : Handelsbezeichnung: Handelsnaam:

Est conforme à : Mit den Anforderungen der folgenden Richtlinien übereinstimmt: Voldoet aan: Er i

Tondeuse à gazon autotractée – Handgeführter Rasenmäher

Gravely

911394

53.3 cm

98/37/EC, 89/336/EEC; 2000/14/EC Conformity Assessment Annex VI. Annexe VI de l'évaluation de conformité.

Konformitätsbewertung, Anhang VI. Bijlage VI voor beoordeling van overeenstemming. Vurdering af overensstemmelse Anneks VI. Annesso VI della valutazione di conformità. Anexo VI de la evaluación de la conformidad. Samsvarsvurdering etter vedlegg VI. Bedömning av överensstämmelse Bilaga VI. Vaatimustenmukaisuuden arviointi, liite VI. Dodatek VI, Ocena zgodno

ci. Anexo VI da Avaliação de Conformidade.

Page 3

Notified Body – Organisme notifié – Zertifizierungsstelle – Aangemelde instantie – Bemyndiget organ – Organismo not i ficato – Organismo notificado – Teknisk kontrollorgan – Anmält organ – Ilmoitettu laitos – Organ zaświadczający – Organismo Certificador –

SNCH 11, Route de Luxembourg L-5230 Sandweiler

Representative Measured Sound Power Level (Lwa) – Niveau de puissance acoustique représentatif mesuré

) – Repräsentativer gemessener Geräuschpegel

) – Representatief gemeten geluidsniveau (Lwa) –

Repræsentativt, målt støjeffektniveau (L potenza sonora rappresentativo rilevato (L potencia acústica representativo medido (L Representativt målt lydeffektnivå (L uppmätt ljudnivå (L

) – Zmierzony reprezentatywny poziom mocy

akustycznej (L Representativo (L

) – Tyypillinen mitattu äänitehotaso

) – Nível de Potência de Som Medido

) –

) – Livello di

) – Nivel de

) –

) – Representativ

911394 : 98 dB

Philip J. Smucker Quality and Conformance Manager (Keeper of Technical File): Responsable de la qualité et de la conformité des produits (Dépositaire de la fiche technique): Manager Qualitätssicherung und Konformität (Archivar der technischen Akte): Kwaliteits- en normalisatiemanager (Beheerder van technische bestand): Chef for kvalitet og overensstemmelse (Indehaver af tekniske data ): Responsabile della qualità e della conformità del prodotto (Depositario del file tecnico): Gerente de calidad y conformidad (Depositariodelarch ivo técnico): Kvalitet- og samsvarsansvarlig (innehaver av teknisk fil): Chef för kvalitet och produktöverensstämmelse (Innehavare av tekniska data): Laadusta ja vaatimustenmu kaisu udes ta vastaava johtaja (Teknisen tiedoston haltija): Kierownik do spraw jakości i zgodności (Przechowujący Dokumentację Techniczną): Gestor de Qualidade e Conformidade (Zelador de Arquivos Técnicos):

CE Sound and Vibration – Bruits et vibrations CE – CE Geräusch- und Vibrationswerte – CE Geluid en trilling – CE støj og vibration – Livello sonoro e vibrazioni CE – Sonido y vibración

Guaranteed Sound Power Level (L Niveau de puissance acoustique garanti (L Garantierter Geräuschpegel (L geluidsniveau (L Livello di potenza sonora garantito (L acústica garantizado (L Garanterad uppmätt ljudnivå (L äänitehotaso (L poziom mocy akustycznej (L Som Garantido (L

) – Garanteret støjeffektniveau (Lwa) –

) – Garantert lydeffektnivå (Lwa) –

) – Gwarantowany reprezentatywny

) –

Ariens Company Brillion, WI 54110-0157 USA Signature Signature Unterschrift Handtekening Underskrift Firma

Firma Signatur Namnteckning Allekirjoitus Podpis Assinatura

) –

) – Gegarandeerd

) – Nivel de pot encia

) – Taattu

) – Nível de Potência de

911394 : 100 dB

11/24/2 003 Date Date Datum Datum Dato Data Fecha Dato Datum Päiväys Data Data

CE – CE-lyd og -vibrasjon – CE ljudnivå och vibrationer – CE, melu ja tärinä – CE Dźwięku i Wibracji – Som e Vibração CE – (Ref. EN836-2001)

911394

Oper. Ear Sound Pressure (Lpa) in dBA –

Geräuschpegel am Ohr des Bedieners (L Strøjtryk ved brugeren s ør e (L de sonido en el oído (L

– Kuljettajan korvaan kohdistuva äänenpaine (Lpa), dBA – Robocze ciśnienie akustyczne na uch u (Lpa) w

decybelach

– Oper. Pressão do Som no O uvido (Lpa) em dBA –

) målt i dBA – Pressione sonora all’orecchio dell’operatore (Lpa) in dBA – Presión

) in dBA – Lydtrykk ved førerens øre (Lpa) inn dBA – Ljudeffekt vid förarens öron (Lpa) i

Pression acoustique aux oreilles de l’opérateur (Lpa) en dBA –

) in dBA – Geluidsdruk bij het oor van de gebruiker (Lpa) in dBA –

Vibration Measure (m/sec2) at Operator:

) an des Bedieners: Gemeten trilling bij (m/sec2): Vibrationsmålinger (m/s2) ved brugerens: Vibrazioni

(m/s percepite dall’operatore (m/sec førerens: Vibrationsmått (m/s Medida de Vibração (m/seg.

Hands –

Mains – Hände – De handen van de gebruiker – Hænder – Mani – Manos – Hender – Händer –

): Medida de vibrac ión (m/s eg2) en el operador: Vibrasjonsmåling (m/s2) ved

) vid förarens: Tärinä (m/s2) kuljettajan: Pomiar wibracji (m/sec2) u operatora:

) no Operador:

Käsissä – Ręce – Mãos –

Mesure des vibrations (m/s2) au niveau de l’opérateur: Vibration

X3.6 Y5.5 Z4.4

Page 4

Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Assembly . . . . . . . . . . . . . . . . . . . . . . . . 9

Controls and Features . . . . . . . . . . . . 10

Operation . . . . . . . . . . . . . . . . . . . . . . . 11

Maintenance. . . . . . . . . . . . . . . . . . . . . 15

Service and Adjustment s. . . . . . . . . . 17

INTRODUCTION

Storage. . . . . . . . . . . . . . . . . . . . . . . . . 21

Troubleshooting . . . . . . . . . . . . . . . . . 21

Service Par ts . . . . . . . . . . . . . . . . . . . . 22

Accessories. . . . . . . . . . . . . . . . . . . . . 22

Specifications . . . . . . . . . . . . . . . . . . . 23

Warranty. . . . . . . . . . . . . . . . . . . . . . . . 24

THE MANUAL

Before using the unit, carefully and completely read your manuals. The contents will give you an understanding of safety instructions and controls during normal operation and maintenance.

All reference to left, right, front, or rear are given from the operator’s position, facing the direction of forward travel.

SERVICE AND REPLACEMENT PARTS

When ordering replacement parts or making service inquiries, know the Model and Serial numbers of your unit and engine.

Numbers are located on the product registration form in the unit literature package. They are also printed on a serial number label, located on the frame of your unit (Figure 1 and Figure 2).

Serial Number Label

Figure 1

OM1600

Unit Serial Number Label

Engine Serial Number Label

Figure 2

• Record Unit Model and Serial numbers here:

• Record Engine Model & Serial numbers here:

OM1825

PRODUCT REGISTRATION

The Gravely dealer must register the product at the time of purchase. Registering the product will help the company process warranty claims or contact you with the latest service information. All claims meeting requirements during the limited warranty period will be honored, whether or not the product registration card is returned. Keep a proof of purchase if you do not register your unit.

Customer Note: If the Dealer does not register your product, please fill out, sign and return the product registration card to Gravely or go to www.Gravely.com on the internet.

GB - 4

Page 5

UNAUTHORIZED REPLACEMENT PARTS

Use only Gravely replacement parts. Replacing any part on this vehicle with anything other than a Gravely authorized replacement part may adversely affect the performance, durability, or safety of this unit and may void the warranty. Gravely disclaims liability for any claims or damages, whether warranty, property damage, personal injury or death arising out of the use of unauthorized replacement parts. To locate your nearest Gravely Dealer, call 1-800-472-8359 or go to www.Gravely.com on the internet.

DEALER DELIVERY

Dealer should:

1. Check that all assembly and adjustments have been properly completed.

2. Fill out Original Purchaser Registration Card and return the card to Gravely.

SAFETY

WARNING: This cutting machine

is capable of amputating hands and feet and throwing objects. Failure to observe the safety instructions in the manuals and on decals could result in serious injury or death.

Slopes are a major factor related to slip and fall accidents. Operation on all slopes requires extra caution.

Tragic accidents can occur if the operator is not alert to the presence of children. Never assume that children will remain where you last saw them.

Gasoline is extremely flammable and the vapors are explosive, handle with care.

Stop unit and engine and allow moving parts to stop before leaving operator’s position.

3. Explain Gravely Limited Warranty Policy.

4. Explain recommended lubrication and maintenance. Advise customer on adjustments. Remind customer to change oil in 4 cycle engine crankcase after first five (5) hours of operation.

5. Instruct customer on controls and operation of unit. Discuss and emphasize the Safety Rules. Give customer Owner/Operator, Parts, and Engine manuals. Advise customer to thoroughly read and understand them.

DISCLAIMER

Gravely reserves the right to discontinue, make changes to, and add improvements upon its products at any time without public notice or obligation.The descriptions and specifications contained in this manual were in effect at printing. Equipment described within this manual may be optional. Some illustrations may not apply to your unit.

SAFETY ALERTS

Look for these symbols to point out important safety precautions. They mean:

Attention! Personal Safety Is Involved! Become Alert! Obey The Message!

The safety alert symbols above and signal words below are used on decals and in this manual.

Read and understand all safety messages.

DANGER: IMMINENTLY HAZARDOUS SITUATION! If not avoided, WILL RESULT in death or serious injury.

WARNING: POTENTIALLY HAZARDOUS SITUATION! If not avoided, COULD RESULT in death or serious injury.

GB - 5

CAUTION: POTENTIALLY HAZARDOUS SITUATION! If not avoided, MAY RESULT in minor or moderate injury. It may also be used to alert against unsafe practices.

Page 6

NOTATIONS

NOTE: General reference information for

proper operation and maintenance practices. IMPORTANT: Specific procedures or

information required to prevent damage to unit or attachment.

PRACTICES AND LAWS

Practice usual and customary safe working precautions, for the benefit of yourself and others. Understand and follow all safety messages. Be alert to unsafe conditions and the possibility of minor, moderate, or serious injury or death. Learn applicable rules and laws in your area.

REQUIRED OPERATOR TRAINING

Original purchaser of this unit was instructed by the seller on safe and proper operation. If anyone other than the original purchaser will use the unit, ALW AYS provide this manual and any needed safety training before operation.

SAFETY DECALS AND LOCATIONS

ALWAYS replace missing or damaged safety decals. Refer to Figure 3 for safety decal locations.

1. DANGER!

TO AVOID SERIOUS INJURY OR DEATH

Read the operator’s manual.

OL1801

Keep children and others away from unit while operating.

OL4370

Never direct discharge toward other people. Thrown objects can

OL0910

OL3030

cause injury.

Do not operate mower unless guards are in operating position or entire bagger is attached.

OL4540

Keep safety devices (guards, shields, switches, etc.) in place and working.

• Go across slopes, not up and down.

• Look down and behind before and while moving backward.

• Do not park on a slope unless chocked or blocked.

• Do not allow operation of machine by untrained personnel.

KEEP HANDS AND FEET AWAY

Do not operate mower unless guards are in operating position or bagger is attached.

3. CAUTION!

2. DANGER!

• Bag is subject to wear and deterioration.

• Check bag frequently, replace when necessary.

• Use original bag to comply with safety specifications.

SAFETY RULES

If unit is to be used by someone other than

Figure 3

OM1830

original purchaser; loaned, rented or sold, ALWAYS provide this manual and any needed safety training before operation.

GB - 6

Page 7

Read, understand and follow all safety practices in Owner/Operator Manual before beginning assembly. Failure to follow instructions could result in personal injury and/or damage to unit.

ALWAYS disconnect wire from spark plug before assembly. Unintentional engine start up can cause death or serious injury.

Complete a walk around inspection of unit and work area to understand:

• work area

• your unit

• all safety decals. Clear work area of stones, sticks, wire and foreign objects which might be picked up and thrown. Tall grass can hid e obstacles.

Know the work area. Stay alert for holes, rocks, rough terrain and hidden hazards.

Keep away from drop-offs, ditches, or embankments that could cause operator to lose footing or control of unit.

ALWAYS be aware of traffic when operating along streets or curbs.

Keep work area clear of all persons, children and pets.

Keep children out of the work area and under the watchful care of a responsible adult.

ALWAYS operate unit when there is good visibility and light.

DO NOT mow wet grass. ALWAYS be sure of your footing. Keep a firm

hold on handlebar. Walk, NEVER run. Engine/blade control feature on mower stops

engine and blade within 3 seconds whenever operator releases handlebar. Check this feature frequently. If feature fails to operate, disconnect spark plug wire and adjust or have it repaired before using unit.

Only trained adults may operate unit. Training includes actual operation.

NEVER operate after or during the use of medication, drugs or alcohol. Unit requires complete and unimpaired attention.

NEVER allow children to use mower. ALWAYS keep hands and feet away from

rotating parts. Rotating parts can cut off body parts.

ALWAYS keep hands away from pinch points. Fumes from engine exhaust can cause death

or serious injury. DO NOT run engine in an enclosed area.

ALWAYS protect eyes, face, and body with adequate safety gear and protective clothes. Wear sturdy footwear, gloves and safety goggles or safety glasses with side shields while operating mower.

NEVER operate mower barefoot or when wearing open sandals or canvas shoes.

NEVER wear loose clothes, long hair or jewelry that may get caught in rotating parts.

ALWAYS stand clear of discharge when operating unit.

NEVER direct discharge toward bystanders. Operator is responsible for bystander safety. DO NOT touch hot parts. Allow parts to cool. Keep safety devices or guards in place and

functioning properly. NEVER modify or remove safety devices.

Read, understand, and follow all instructions in the manual and on the machine before starting. Understand:

• How to operate all controls

• The functions of all controls

• How to STOP in an emergency. DO NOT attempt to start your engine until you know what the controls do and how they work.

DO NOT tilt mower when starting it. Keep feet away when starting engine. DO NOT start the engine or operate mower

without side discharge cover or side discharge deflector installed.

Take all possible precautions when leaving unit unattended.

ALWAYS shut off engine and disconnect spark plug wire to prevent accidental starting or unauthorized use.

Stop engine if anyone enters the work area. NEVER attempt to make any adjustments to

unit while engine is running (except where specifically recommended). Stop engine and wait for all moving parts to stop before servicing.

DO NOT make cutting height wheel adjustments while the engine is running.

If you strike an object, or if equipment vibrates abnormally, stop engine at once, wait for moving parts to stop and disconnect wire from spark plug. Repair any damage before restarting unit.

Keep rear door closed when engine is running unless the grass bag is in place.

Stop engine before removing and emptying grass bag.

When mulching or bagging, ALWAYS install discharge cover.

GB - 7

Page 8

When side discharging, ALWAYS install side discharge deflector.

ALWAYS shut off engine, allow blade to stop and disconnect spark plug wire before clearing clogs or cleaning unit.

Check grass bag for wear, damage, and/or deterioration. Replace only with Gravely original equipment replacement parts for safety.

To reduce fire hazar d and overheating, keep equipment free of grass, leaves, debris or excessive lubricants.

Use extra care when approaching blind corners, shrubs, trees, or other objects which may obscure vision.

DO NOT mow at too fast a rate. DO NOT change engine governor setting or overspeed the engine.

Do not operate mower on gravel or loose material such as sand. Stop mower when crossing drives, walks, or roads to prevent damage or injury from thrown objects.

DO NOT pull mower backwards unless absolutely necessary. Look down and back, especially for small children, before and while moving backwards.

On self-propelled models, releasing wheel drive control must stop mower’s forward movement. Releasing wheel drive control must stop mower’s forward movement. If this feature fails to operate, disconnect spark plug wire and repair before using unit.

On self-propelled models, wheel drive must be disengaged when starting engine.

DO NOT operate on steep slopes. NEVER leave unit unattended on a slope.

Chock wheels if parking on a slope. Mow across the face of slopes, never up and

down. Be especially cautious when changing direction on slopes.

This product is equipped with an internal combustion engine. DO NOT use on or near any unimproved, forest or brush covered land unless the exhaust system is equipped with a spark arrestor meeting applicable local, state or federal laws. A spark arrestor, if used, must be maintained in effective working order by the operator. See your Gravely Dealer or engine manufacturer’s service center.

Fuel is highly flammable and its vapors can explode. ONLY use approved fuel containers.

• NO Smoking!

• NO Sparks!

• NO Flames!

• Allow engine to cool before filling fuel tank.

Never fill containers inside a vehicle or on a truck or trailer bed with a plastic liner. Always place containers on the ground away from your vehicle before filling.

When practical, remove gas-powered equipment from the truck or trailer and refuel it on the ground. If this is not possible, then refuel such equipment on a trailer with a portable container, rather than from a gasoline dispenser nozzle.

Keep the nozzle in contact with the rim of the fuel tank or container opening at all times until fueling is complete. Do not use a nozzle lock-open device.

Check fuel supply before starting engine. DO NOT fill gasoline tank indoors, when

engine is running, or while engine is hot. Allow engine to cool several minutes before

removing fuel cap. DO NOT overfill. Allow about 1/4" (6 mm) of

tank space for fuel expansion. Replace gasoline tank cap securely and

clean any spilled fuel before starting engine. If fuel is spilled on clothing, change clothing

immediately. NEVER store fuel inside where there is an

open flame, such as a water heater. ALWAYS drain fuel outdoors away from

ignition sources. ALWAYS shut off engine when transporting

unit on a truck or trailer. Avoid Electric Shock. DO NOT disconnect

wire from spark plug while engine is running. Accidental engine start up can cause death or

serious injury. Except where specifically recommended, ALWAYS stop engine, wait for moving parts to stop, allow parts to cool and disconnect spark plug wire before inspecting, servicing, adjusting or repairing unit.

Keep mower free of grass, leaves, or other debris build-up.

Keep equipment in good condition. Maintain or replace safety and instruction

labels, as necessary. Follow engine manufacturer’s safety

instruction when servicing engine. Check all hardware at regular intervals,

especially blade attachment bolts. Keep all hardware properly tightened.

Before tipping unit, remove fuel. Ensure all wheel blocks, jack stands and tie

downs will support unit during maintenance. Replace worn-out mufflers immediately.

Continued use could result in fire or explosion.

GB - 8

Page 9

Sharp edges can cut or amputate fingers or a hand. Wrap blade or wear sturdy gloves to service.

Use only replacement parts designed for your unit. See your Gravely Dealer.

Allow engine to cool before storing in any enclosure.

ALW AYS clean unit before extended storage. See engine manual for proper storage.

ASSEMBLY

CAUTION: AVOID INJURY. Read

and understand the entire Safety section before proceeding.

CARTON CONTENTS

DO NOT store unit inside a building with fuel in the fuel tank where any ignition sources are present.

Use only accessories which have been approved by Gravely and are properly installed.

Check attachments frequently and replace worn or damaged components with manufacturer’s recommended parts.

ASSEMBLY

1. Unfold and adjust handlebar. See Handlebar Height on page 17.

NOTE: DO NOT bend the speed control rod (if equipped) when unfolding the handlebars.

2. Fill engine crankcase with oil. See engine manual.

3. Set-up mower for bagging, side discharge (911098, 100) or mulching. See Mower Set-Up on page 13.

4. Fill fuel tank. See Filling Fuel Tank on page 13.

5. Connect spark plug wire.

6. Check the engine/blade control feature. Try starting the engine without the engine/blade control held against the handlebar. Engine must not start. If engine starts, stop engine and adjust or repair engine/blade control. See Engine/Blade Control Adjustment on page 18.

1. Mower Unit

2. Side Discharge Cover (911098, 100)

3. Side Discharge Deflector (911098, 100)

4. Grass Bag Frame

5. Literature Pack

6. Mulch Plug

7. Grass Bag

Figure 4

OM1620

GB - 9

Page 10

CONTROLS AND FEATURES

1. Engine/Blade Control

2. Wheel Drive Control (911094, 098, 100,

394)

3. Adjustable and Folding Handlebars

4. Swivel Wheel Lock (911100)

5. Grass Bag

6. Rear Door

7. Fuel Tank and Cap

8. Fuel Shutoff Valve (911094, 095, 394)

9. Height Adjustment Pins

10. Muffler and Muffler Guard

11.Oil Fill/Dipstick

12. Oil Filter

13. Cutting Height Levers (2 Rear Wheel Adjusters, 2 Front Wheel Adjusters)

14. Primer Bulb (911098, 100)

15. Air Filter

16. Side Discharge Cover (911098, 100)

17. Side Discharge Deflector (911098, 100)

18. Mulch Plug

19. Handlebar Adjustment Holes

20. Recoil Starter Handle

21. Speed Control Rod (911094, 098, 100,

394)

22. Throttle Control (911094, 095, 394)

Figure 5

GB - 10

Page 11

OPERATION

CONTROLS AND FEATURES

See Figure 5 for locations.

WARNING: Improper operation can lead to injury. Learn what the controls do and how they work. Thoroughly read and understand entire Operator Manual.

CAUTION: AVOID INJURY. Read and understand the entire Safety section before proceeding.

Engine/Blade Control

CAUTION: Check function of

Engine/Blade Control regularly. Improper function of control could cause injury.

The engine/blade control must be held against the handlebar to start the engine and blade.

Engine/blade control feature on mower stops engine and blade within 3 seconds whenever operator releases handlebar. Check this feature frequently. If feature fails to operate, disconnect spark plug wire and adjust or have it repaired before using unit.

CAUTION: Both rear wheels must be set at same height or traction drive may not work properly.

Cutting Height Settings Chart

Notch Cut grass length LOW 1" (25 mm) 2 1-3/8" (35 mm) 3 1-3/4" (45 mm) 4 2-1/4" (57 mm) 5 2-3/4" (70 mm) HIGH 3-1/4" (83 mm)

Standard Models

T o change cutting height, move cutting height levers one notch at a time on each wheel to set desired height (Figure 6).

NOTE: Each wheel on mower must be set at the same height for a level cut.

High

Low

STOP START and RUN

OM1230

Handlebar

Adjust handlebar to a safe and comfortable height. See Handlebar Height on page 17.

Recoil Starter Handle

When pulled, handle will turn engine over.

CUTTING HEIGHT ADJUSTMENT

DANGER: Avoid injury from

rotating blade. ALWAYS shut off engine before adjusting cutting height.

GB - 11

Low

1. Cutting Height Lever Figure 6

Rear

High

Front

OM0165

Page 12

Swivel Wheel Models (911100)

To change fron t wheel cutting height, insert height adjuster pin into the holes that match the desired cutting height and fasten with key ring (Figure 7).

To change rear wheel cutting height, move cutting height levers one notch at a time to set the desired cutting height.

High Low

Speed Control (self-propelled models)

Speed control rod changes the mower’s forward travel speeds.

High –Push rod all the way forward.

Rear

Front

1. Cutting Height Lever

2. Height Adjuster Pin

3. Key Ring Figure 7

Primer Bulb (911098, 100)

Push the primer bulb in to add fuel for easier engine start.

Throttle (911094, 095, 394)

The throttle controls the engine speed and chokes

engine for starting.

1.Start - Push lever all the way forward.

2.Fast.

3.Slow - Pull lever all the way rearward.

OM1270

OM0480

Low –Pull rod all the way rearward.

Start mowing slowly and use speed control rod to gradually increase speed to a safe, comfortable walking pace.

Speed control rod should hold the desired speed. If not, adjust speed control bell crank. (See Speed Control Bell Crank (self- propelled models) on page 20.)

Wheel Drive Control (self-propelled models)

CAUTION: Unit will move forward

at engine start if wheel drive control is engaged. ALWAYS release wheel drive control before starting unit.

NOTE: Engine must be running for wheel drive to propel unit.

To drive forward: Slowly squeeze and hold wheel drive control

against handlebar. To stop: Release wheel drive control.

OL2074

GB - 12

STOP

OM1240

Page 13

Swivel Wheel Lock (911100)

CAUTION: Avoid loss of control.

Lock swivel wheels when mowing on a slope or hill. Do not mow on steep slopes.

To hold wheel straight:

1. Push swivel wheel lock forward.

2. Push unit forward until wheel locks in place.

To allow wheel to swivel:

1. Pull swivel wheel lock back.

Unlock - Wheel Swivels

Lock - Wheel Held Straight

FILLING FUEL TANK

To add fuel to fuel tank:

1. Put unit in open or well-ventilated area.

2. Stop engine and allow to cool.

3. Clean fuel cap and surrounding area.

4. Remove cap.

IMPORTANT: See engine manual for correct type and grade of fuel.

5. Fill fuel tank. (see Specifications on page 23 for tank capacity.)

6. Replace fuel cap and tighten.

7. ALWAYS clean any spilled fuel.

MOWER SET-UP

CAUTION: DO NOT operate

mower unless either side discharge cover or side discharge deflector is installed. Thrown objects may cause damage or injury. Never operate unit with rear door open unless grass bag is in place.

OM1700

Fuel Shutoff Valve (911094, 095, 394)

IMPORTANT: The fuel shutoff valve MUST

be in the closed position prior to transporting the unit.

Open the fuel shutoff valve to operate the unit. Close the fuel shutoff valve when storing, transporting or servicing the unit.

Fuel shutoff valve open.

Fuel shutoff valve closed.

CAUTION: If clog or obstruction prevents grass flow, release engine/blade control and disconnect spark plug wire before attempting to clear away any clogs.

To Bag

CAUTION: Check grass bag

frequently for wear or deterioration. Replace worn or damaged bag with Gravely original equipment replacement bag only.

1. Shut off unit.

2. Install side discharge cover (911098,

100).

3. Lift rear door.

4. Hook grass bag frame on mounting flange.

5. Lower rear door.

If necessary, lift rear of grass bag frame to lock in position.

There should be no openings between bag and mounting surface after installing bag. If necessary, clear debris from bag mounting surface.

GB - 13

Page 14

Grass Bag Removal

1. Shut off unit.

2. Lift rear door.

3. Use handle to lift bag off mounting flange.

4. Close rear door.

NOTE: Empty grass bag and clean mower pan after each use. DO NOT allow grass clumps or a grass coating to collect inside of grass bag or mower pan. Remove grass bag from mower, wash bag with hose and allow to dry.

To Side Discharge (911098, 100)

1. Shut off unit.

2. Remove grass bag.

3. Install Mulchmaster plug (see below).

4. Remove side discharge cover and keep hardware.

5. Attach side discharge deflector to studs on mower. Make sure deflector covers discharge opening.

6. Secure with cover hardware from step 4.

To Mulch

1. Shut off unit.

2. Remove grass bag and install side discharge cover (911098, 100).

3. Open rear door and insert Mulchmaster plug with the beveled face to the left.

4. Close rear door.

NOTE: Rear door must close flush. NOTE: For maximum mulching performance,

install the Mulchmaster Mulching Kit. See Accessories.

EMERGENCY STOPPING

To stop the mower in an emergency:

1. Release the engine/blade control.

2. Release the wheel drive control (selfpropelled models).

3. Allow all moving parts to stop before leaving operator’s position.

STARTING AND SHUT OFF

WARNING: Improper operation

can lead to injury. Learn what the controls do and how they work. Thoroughly read and understand entire Operator Manual.

SeeFigure 5 for all Controls and Features. NOTE: Start engine on a level surface that is

free of debris.

Manual Start

1. Check each item under Before Each Use in the Maintenance Schedule on page 15.

2. Open fuel shutoff valve (911094, 095,

394).

3. For engines with a primer, push primer bulb 2 or 3 times for a cold engine.

NOTE: It is unnecessary to prime or choke a warm engine.

4. For engines with a throttle, place throttle control in the choke position. Once the engine has started, place throttle in the high speed detent.

5. With engine/blade control held against the handlebar, grasp starter handle and pull rope slowly until it pulls harder. This is the compression stroke. Let rope rewind slowly.

6. Pull rope with rapid continuous full arm stroke to start engine. Allow rope to rewind slowly.

IMPORTANT: DO NOT let starter handle snap against bracket.

7. Repeat steps 4 and 5 until engine starts. (If engine does not start, see Troubleshooting on page 21.)

Shut Off

1. Release wheel drive control and allow unit to stop completely (self-propelled models).

2. Release engine/blade control.

3. Set throttle control to "Stop."

Mowing Tips

Cut grass when it is dry. Keep mower blades sharp. Do not set cutting height too low. For tall

grass, mow twice. Do not mow too fast. Mow with engine at full throttle. Discharge

clippings into areas already cut. Vary cutting pattern with each mowing. NOTE: To prevent dirt and grass from

collecting on mower pan, avoid operating over bare ground with only patches of grass.

GB - 14

Page 15

Mulching Tips

For best mulching performance, cut no more than 1 inch (2.54 cm) of grass per cutting.

MAINTENANCE

CAUTION: AVOID INJURY. Read

and understand the entire Safety section before proceeding.

Gravely Dealers will provide any service, parts or adjustments which may be required to keep your unit operating at peak efficiency . Should engine require service, contact a Gravely Dealer or an authorized engine manufacturer's service center.

MAINTENANCE SCHEDULE

NOTE: Some working conditions (heavy

loads, high ambient temperatures, dusty conditions, or airborne debris) may require more frequent service.

See engine manual for further maintenance and troubleshooting information.

CHECK WHEEL DRIVE CONTROL (self-propelled models)

The unit must stop quickly and completely when the control is released. Adjust or repair if necessary. See Wheel Drive Control Adjustment (self-propelled models) on page 20.

CHECK GRASS BAG

Check grass bag frequently for wear or deterioration. Replace worn or damaged bag with Gravely original equipment replacement bag only.

CLEAN UNIT

Before each use clean unit, muffler and engine surfaces of debris, oil or fuel spills to ensure proper cooling and prevent fires.

MAINTENANCE

SCHEDULE

Service Performed Check Engine/Blade

Control Check Wheel Drive Control Check Grass Bag • Clean Unit • Check Engine Oil • Check Mower Blade • Check Drive Belt • Check Fasteners • Check Air Cleaner • Change Engine Oil

General Lubrication • Check Spark Plug • Check Engine Cooling Check Muffler •

After first 5 Hours of operation

Before

Each

Use

CHECK ENGINE/BLADE CONTROL

The engine and blade must stop within 3 seconds after releasing the control. If the engine and blade continue to run, adjust or repair control immediately. See Engine/Blade Control Adjustment on page 18.

25 100

•

CHECK ENGINE OIL

IMPORTANT: Maintain proper oil level at all

times or engine damage will result. Check the level of the engine crankcase oil

before each use. Make sure engine is level when checking oil.

See engine manual for instructions.

CHECK MOWER BLADE

See Figure 8. Check blade mounting: blade must be secure

and bolt torqued to 37.5 - 50 lbf-ft (51-68 N•m) (bolt should fully compress lock washer).

Check blade for nicks and dull cutting edges. Sharpen if necessary.

Check blade for rounded or broken ends, thinned metal or other damage. Replace if necessary.

NOTE: Blades should be sharpened and balanced professionally. Contact your Gravely Dealer.

To remove blade:

1. Stop engine, wait for all moving parts to stop, and disconnect spark plug wire.

2. Block blade to prevent rotation.

3. Remove bolt, lock washer, flat washer and blade from shaft.

To install blade:

1. Replace blade, flat washer, lock washer and bolt on shaft.

GB - 15

Page 16

2. Torque bolt to 37.5 - 50 lbf-ft (51-68 N•m) (bolt should fully compress lock washer).

3. Connect spark plug wire.

Sharpen the Mower Blades

CAUTION: DO NOT sharpen

mower blades while on unit. An imbalanced mower blade will cause excessive vibration and eventual damage to unit. Check mower blade balance before reinstalling blades.

NEVER weld or straighten bent blades.

1. Remove mower blade from unit.

Discard mower blade if:

• More than 1/2 in. (1.27 cm) of metal is removed.

• Air lifts become eroded.

• Blade is bent or broken.

2. Sharpen mower blade by removing an equal amount of material from each end of mower blade. DO NOT change angle of cutting edge or round the corner of the mower blade.

DO NOT Sharpen to This Pattern

3. Check mower blade balance. Slide mower blade on an unthreaded

bolt. A balanced blade should remain in a horizontal position. If either end of mower blade moves downward, sharpen the heavy end until blade is balanced (Figure 9).

4. Install mower blade on unit.

5. Tighten the bolts to a torque of 37.5 50 lbf-ft (51-68 N•m).

Blade

Bolt

Figure 9

OA0013

CHECK DRIVE BELT (self-

propelled models)

Check drive belt and replace if worn or damaged. See Drive Belt Replacement (self- propelled models) on page 19.

DISCARD if More Than 1/2 in. (1.27 cm)

Sharpen to This Pattern

1. Square Corner

2. Cutting Edge

3. Air Lift

4. Air Lift Erosion Figure 8

CHECK FASTENERS

Check all fasteners for proper tightness. Pay special attention to blade hardware and all guards, shields and safety devices.

CHECK AIR CLEANER

See engine manual for specific information.

OT0792

CHANGE ENGINE OIL

IMPORTANT: Change engine crankcase oil

after first five (5) hours of operation. Then change oil after every 25 hours of operation.

Refer to engine manual for instructions and proper oil type.

IMPORTANT: Proper oil level must be maintained at all times or engine damage will result. DO NOT overfill. Be sure engine is level when adding oil.

GENERAL LUBRICATION

NOTE: LM21SCH has lube fittings on drive

mount for use in commercial applications. Lubricate as needed.

GB - 16

Page 17

Swivel Wheels (911100)

See Figure 10. Use Sten Mix Hi-Temp Grease or equivalent

on the lube fittings. Order P/N: 00036800 - 3 pack of 3 oz. cartridges.

Lube Fitting

Figure 10

OM1282

CHECK SPARK PLUG

Spark plug should be replaced every 100 hours of operation or each year.

NOTE: Loose spark plug wire terminals can cause sparking. Replace terminal if damaged.

CHECK ENGINE COOLING

WARNING: HOT SURFACES can

cause death or serious injury. DO NOT TOUCH parts which are hot from operation. ALWAYS allow parts to cool.

To prevent overheating, air must circulate freely around the cooling fins, cylinder head and block.

Every 100 hours of operation or yearly (more often if conditions require) remove blower housing and clean cooling fins. See engine manual for instructions.

CHECK MUFFLER

Check muffler for debris, cracks, wear, or other damage.

CAUTION: Replace worn-out mufflers immediately. Continued use could result in fire or explosion.

SERVICE AND ADJUSTMENTS

CAUTION: AVOID INJURY. Read

and understand the entire Safety section before proceeding.

SERVICE POSITI ON

Put unit into service position for easy access to underneath the deck.

CAUTION: Avoid fuel spills. Follow steps below to help prevent fuel spills. If fuel leaks into air cleaner, replace air cleaner. ALWAYS clean up any spilled fuel.

1. Place unit on a flat, level surface.

2. Disconnect spark plug wire.

3. Remove fuel cap, place a piece of plastic bag over the opening and tighten cap securely.

4. Tip unit onto left side, opposite the discharge opening (911098, 100).

Tip unit onto right side (911094, 095,

394). Make sure unit is secure and will not tip

over.

IMPORTANT: Remove plastic from fuel cap after unit is upright and service is complete.

HANDLEBAR HEIGHT

To adjust (Figure 11 and Figure 12):

1. Place a hole at the bottom of the braces over the pins on the bracket (911098,

100).

2. Use the fasteners to attach one of the holes at the top and one of the holes at the bottom (911094, 095, 394).

NOTE: To fold handlebars flat for storage, pull the speed control rod (if equipped) all the way back, disconnect braces from support bracket, and fold handlebar forward. Do not bend speed control rod.

GB - 17

Page 18

Hole

911098, 100

ENGINE/BLADE CONTROL ADJUSTMENT

To adjust engine/blade control:

1. Loosen cable nuts away from bracket.

1. Handlebar

2. Adjustment Hole

3. Support Bracket

Figure 11

911094, 095, 394

4. Fasteners

5. Brace

Figure 12

OM1660

OM1800

OM1010

2. Squeeze z-bend bracket at engine end of cable toward front of unit and hold in place.

OM1040

3. Pull cable down from bracket until there is no slack in cable.

No slack

OM106

GB - 18

Page 19

4. Tighten lower

cable nut to 1/8" (3 mm) below bracket.

1/8

(3 mm)

Release z-bend bracket.

OM1020

5. Tighten upper cable nut until bracket is secure between cable nuts.

OM1030

6. Engage engine/blade control. Measure distance between middle of z-bend and cable bracket. Measurement should be as shown below.

Briggs Engines:1.325"-1.788" (3.4 cm - 4.5 cm) Honda Engines: 1.65"-1.69" (4.2 cm - 4.3 cm)

OM10

7. If correct measurement cannot be set, contact your local dealer.

DRIVE BELT REPLACEMENT

(self-propelled models)

To remove drive belt:

1. Disconnect spark plug wire.

2. Set the right rear wheel to its lowest cutting height, and the left rear wheel to the third cutting height. This position provides clearance between friction disc and drive sheave.

3. Remove belt from the idler, then the drive sheave, and finally, the engine pulley (Figure 13).

4. Pull belt through opening under mower pan and over blade.

5. Make sure the idler pulley turns and the idler arm moves freely.

6. Reinstall drive belt in reverse order.

IMPORTANT: Be sure the belt seats in sheave and pulley grooves with the idler touching the back (flat) side of belt.

7. Adjust rear wheels to the same cutting height.

1. Blade

2. Idler

3. Drive Sheave

4. Drive Belt

5. Engine Pulley

6. Bolt, Lock Washer & Flat Washer

Figure 13

GB - 19

Page 20

WHEEL DRIVE CONTROL ADJUSTMENT

models)

See Figure 14.

2-1/4" to 2-3/4" (5.7 to 7 cm)

1. Handlebar Indentation

2. Wheel Drive Control

3. Traction Cable

4. Cable Nuts

The wheel drive must start to engage when wheel drive control is between 2-1/4" and 2-3/4" (5.7 and 7 cm) away from the handlebar.

To check :

1. With engine off, select a slow speed.

2. Slowly pull unit backwards.

3. Slowly squeeze wheel drive control until wheels stop.

4. Measure the distance between the wheel drive control and handlebar at the handlebar indentation.

To adjust:

1. If the measurement is more than 2-3/4" (7 cm), loosen the lower cable nut and then tighten the upper cable nut against the adjuster bracket.

2. If the measurement is less than 2-1/4" (5.7 cm), loosen the upper cable nut and then tighten the lower nut against the adjuster bracket.

3. Recheck measurem ent with the slowest and fastest speeds selected.

4. Repeat adjustment until wheel drive control is properly adjusted.

IMPORTANT: If there is not enough thread length for proper adjustment, contact your Dealer for repairs before operating unit.

(self-propelled

OM0294

Figure 14

SPEED CONTROL BELL CRANK

(self-propelled models)

The speed control bell crank holds the speed control rod in position after a speed has been set. The spring washers may become loose with normal wear. If the speed control rod does not stay firmly in position, adjust the speed control bell crank. See Figure 15.

To adjust:

1. Remove cover, fully compress the helical spring lock washers with lock nut and then back lock nut off, one quarter turn.

2. If the speed control rod is still too loose, tighten lock nut by small increments until it holds its position. Tightening the lock nut too much will not allow the speed control rod to move at all.

3. Align notch in left hand side of cover with bolt and secure with knob.

1. Lock Nut

2. Helical Spring Lock Washers

3. Speed Control Bell Crank

4. Swivel

5. Hair Pin

6. Speed Control

Figure 15

OM1670

Rod

GB - 20

Page 21

STORAGE

CAUTION: AVOID INJURY. Read

and understand the entire Safety section before proceeding.

IMPORTANT: NEVER spray unit with highpressure water or store unit outdoors. Store mower in a cool, dry, protected location.

Cleaning

Clean unit thoroughly with mild soap and low pressure water. Brush off dirt and debris from all surfaces. Touch up all scratched surfaces to prevent rust. Matching touch-up paint is available from your Gravely Dealer. Do not use abrasives, solvents, or harsh cleaners.

Inspection

Inspect mower and repair or replace worn or damaged parts to avoid delays when beginning use again.

Regularly check all hardware and keep fasteners tight. Know unit is in safe working condition.

Grass Bag

Wash out grass bag and allow to dry before storage. Grass bag may be stored in position on mower.

Engine

When storing unit for extended periods of time, remove all fuel from tank and carburetor (run dry). Refer to engine manual.

TROUBLESHOOTING

PROBLEM PROBABLE CAUSE CORRECTION Engine will not

start

Engine is difficult to restart

Cut is poor

Grass does not disperse evenly

Mower does not bag clippings

1. Fuel tank empty or low.

2. Spark plug wire loose or off.

3. Throttle control not in proper position.

4. Engine/Blade control cable detached, broken, or not adjusted properly.

1. Mower clogged with grass. 1. Clear clippings from under

1. Worn blade.

2. Too much grass is being removed per cutting.

3. Grass is too wet.

4. Mowing speed is too fast.

1. Too much grass is being removed per cutting.

2. Grass is too wet.

3. Mowing speed is too fast.

1. Grass bag is overfilled.

2. Mulching plug is installed.

1. Check fuel level. Fill tank if necessary.

2. Check connection.

3. Adjust throttle to FAST position.

4. Check cable. Adjust, repair or replace as necessary.

mower. (Allow the mower to clear clippings before shutting off engine.)

1. Check blade (see Check Mower Blade on page 15).

2. Raise cutting height.

3. Allow grass to dry.

4. Mow slower.

1. Raise cutting height.

2. Allow grass to dry.

3. Mow slower.

1. Empty grass bag and do not allow it to overfill.

2. Remove mulching plug.

GB - 21

Page 22

PROBLEM PROBABLE CAUSE CORRECTION Wheel drive

does not engage (SelfPropelled models)

1. Wheel drive control not engaged.

2. Drive belt out of position.

3. Drive belt worn or damaged.

4. Rear wheels in different cutting heights.

5. Idler spring detached.

6. Wheel drive control cable detached or broken.

7. Friction disc not adjusted properly or damaged.

8. Bearings damaged.

9. Debris in gear set.

1. Engage wheel drive control.

2. Check drive belt. Adjust as necessary (see Check Drive Belt (self-propelled models) on page 16).

3. Replace belt (see Check

Drive Belt (self-propelled models) on page 16).

4. Adjust rear wheels to same cutting height (see Cutting Height Adjustment on page 11).

5. Attach idler spring to notch on idler arm. Contact your Dealer.

6. Check wheel drive control cable. Adjust or replace as needed. See Check Wheel

Drive Control (self-propelled models) on page 15.

7. Contact your Dealer.

8. Contact your Dealer.

9. Contact your Dealer.

SERVICE PARTS

Always use genuine Gravely parts to keep your mower running like new.

Description Part Number Air Filter 08270501 (911094, 095, 394)

21535600 (911098, 100)

Spark Plug 08270502 (911094, 095, 394)

21534100 (911098, 100)

Blade 01137000 (Standard)

01182400 (Tungs ten) Drive Belt 07217100 (094, 911098, 100) Friction

Disc

03248300 (911094) 51102500 (911098, 100)

ACCESSORIES

See your authorized Gravely Dealer to add these optional accessories.

71102400 Dethatcher 71102700 Mulchmaster Plug 71103000 Grass Bag 71103200 Rear Discharge Chute 71103500 Mulchmaster Mulching Kit 71103700 Leaf Shredder 71104100 Front Swivel Wheel Kit 71104700 Bag-N-Drag Bagger Kit

GB - 22

Page 23

SPECIFICATIONS

Model Number 911094 911095 911098 911100 911394 Description PRO21SCH PRO21CH LM21S LM21SW PRO21SCH Length - in (cm) 61.5 (156) Height - in (cm) 38 (96.5) Width - in (cm) 23 (58.4) Actual Weight - lbs (kg) 115 (52.2) 99 (44.9) 97 (44) 109 (49.5) 115 (52.2) Cutting Width 21 (53.3) Cutting Height - in. (cm) 6 Positions: 1.00-3.25 (2.5 - 8.3) Engine Honda 4 cycle Briggs & Stratton 4 cycle Honda 4

Model GXV160KA12 126602-0146E1 GXV160Engine Power - HP (kW) @

Maximum RPM Max Rotation Speed of Cutting Edge - RPM (min Governed RPM 3200 +/- 150 2800 +/- 100 2850 +/- 50

Displacement Cu. In. (cc)

Cylinder Bore Cast Iron Sleeve Aluminum Cast Iron Engine Oil Type See engine manual.

Crank Case Capacity - Oz. (Liter)

Oil System Forced/Splash Splash Forced/ Spark Plug Gap - in (mm) 0.028 - 0.031 (0.70 -

Fuel Type Unleaded Fuel Tank Capacity - qt

(Liter) Throttle Standard N/A Standard Air Cleaner Paper Element w/ Foam Paper Element Paper

Starting Recoil Differential Standard N/A Standard Variable Speeds - MPH

(km/hr) Mower Deck 14 Gauge - Stamped Steel Front Wheel Dia - in (cm) 7.5 (19.1) 7.0 (17.8) 7.5 (19.1) Rear Wheel Dia - in (cm) 10.5 (26.7) 10.0 (25.4) 10.5 (26.7)

-1

)

5.5 (4.0) 6.75 (5.0) 5.5 (4.0) 3350 2900 2900

9.9 (163.4) 11.57 (190) 9.9 (163.4)

22 (0.65) 20 (0,59) 22 (0.65)

0.020 (0.51) 0.028 -

0.80)

1.06 (1.0) 1.6 (1.5) 1.06 (1.0)

0-4 (0-6.4) N/A 0-4 (0-6.4)

cycle

KA12

Sleeve

Splash

0.031 (0.70

- 0.80)

Element w/

Foam

GB - 23

Page 24

Warranty for Models 911094, 095

GB - 24

Page 25

Warranty for Models 911098, 100

GB - 25

Page 26

GRAVELY A Division of Ariens Company 655 West Ryan Street

P.O. Box 157 Brillion, WI 54110-0157 920-756-2141 Fax 920-756-2407 www.gravely.com

Ariens 911094 - Pro 21SCH, 911095 - Pro 21CH, 911098 - LM21S, 911100 - LM21SW, 911394 - Pro 21SCH User Manual

TABLE OF CONTENTS

INTRODUCTION

SAFETY

ASSEMBLY

CONTROLS AND FEATURES

OPERATION

MAINTENANCE

MAINTENANCE SCHEDULE

SERVICE AND ADJUSTMENTS

STORAGE

TROUBLESHOOTING

SERVICE PARTS

ACCESSORIES

SPECIFICATIONS