Ariens 008-1540, 010-1540 User Manual
Specifications and Main Features
- Model Options:
-VP919008: 15HP Briggs & Stratton Engine + 40" Deck.
-VP919009: 16HP Briggs & Stratton Engine + 48" Deck.
-VP919010: 15HP Kohler Engine + 40" Deck.
- Engine Types:
– Model 915008: 15 HP OHV Truck Lima Engines Range: 10 - 37.5 Nm
- model915009: 16 HP OHV Truck Lima Engines Range: 10 - 37.5 Nm
- model9150010: 15 HP Kohler Range: 10 - 37.5 Nm
3.10 Speed:
– Engine RPM is 3250
- Fuel Tank Capacity:
– All models has 3.5 gallons which is approximately 13.3 litres.
- Crankcase Capacity: Author/Engine Manual Read the small print on the cups.
- 915008: 56 oz which is approx 1.66 litres
- 915009: 64 oz which is approx 1.89 litres
- 915010: 4 pts which is approx 1.9 litres
Fuel Type: Refer to Engine Manual Lubricant Type:
– Refer to Engine Manual
Frequently Asked Questions
– Rear Tires: 18 x 8.50-8 4ply rating
– Front Tires: 11.0 x 4.00-5
Recommended Tire Pressure: between 10 to 12 psi (83-103kN/M2).
- Hydrostatic System:
– Lubricant Type: 20W - 50.
- Speed Capacities (3200 RPM):
– Forward: 0 to 5.7 mph which is approx 9.1 km/hr
– Reverse: 0 to 4.1 mph which is approx 6.6km/hr
- Dimensions:
– Length 71.88 inches (182.5cm)
– Widths 52 inches (132 cm) for model 915008 and 915010 and 60 inches (152.4cm) for model 915009
- Height: 44.7 in, 113.5 cm
- Weight
- 915008: 588 lbs (267 kg)
- 915009: 628 lbs (285 kg)
- 915010: 588 lbs (267 kg)
2) Frequently asked questions
- Which fuel is ideal for the engine?
- For the fuel type intended to be used on your model please refer to the Engine manual.
- How much tire pressure should the unit otherwise have?
- The recommended pressure is from 10-12psi, been 83-103kN/m².
- Outline the steps of starting the unit.
- Make sure that the operator is seated, the control levers are in NEUTRAL LOCK, PTO switch is OFF and choke applied if the engine is cold, throttle set to proper starting position, switch to TURN START and release as the engine has started.
- In the scenario that the engine does not start, what should I do?
- Verify that the battery is charged and the connections are checked. Confirm the PTO switch is OFF and control levers in NEUTRAL LOCK.
- When do I need to check the engine oil?
- To ensure that all is sustained within the safe working condition, engine oil should be checked on a daily basis or at a maximum interval of 5 hours of operation.
- How are mower blades maintained?
- Maintenance of mower blades is dependent on rotation. When it occurs at a slower velocity, the blades are maintained by sharpening them in a regular fashion and checking the blades for any imbalance. Sharp blades assist in better and healthier grass cutting.
- What is the procedure for adjusting the cutting height?
- An adjustment can be made directly via the attachment lift lever over a corresponding range of 1.38 inches to 5 inches.
- Is the unit suitable for steep slope usage?
- If the unit is used on slopes over an angle of 10 degrees then there are high chances of injury thus it is not recommended.
- What do I need to do if I detect abnormal vibrations?
- Just turn off the sensitivity and check for any loose components or damaged features then you are ready to go again.
- Where to obtain spare parts?
- Spare or additional parts can be purchased at a local Ariens vendor or service center that is registered.
User Manual
Loading...