Argos ZWINTD-WHO-AR ASSEMBLY INSTRUCTIONS
MADE IN
BRITAIN
Dimensions
If you need help or have damaged or missing parts, please visit www.argos-support.co.uk
or email: Help@ClickSpares.co.uk (quoting your original order number)
Alternatively, call the Spares Helpline on: 0370 112 1928.
For any other queries please contact the Customer Helpline on: 0345 640 2020
Important - Please read these instructions fully before starting assembly
Winchester - Tall Display Unit
Assembly Instructions - Please keep for future reference
413/9348
Width - 73.3cm
Depth - 32.7cm
Height - 182.5cm
Issue 2 - 29/07/15
Safety and Care Advice
Important - Please read these instructions fully before starting assembly
• Warning: This unit weighs
approximately 38kgs.
Please lift with care.
• Check you have all the
components and tools listed on
pages 1, 2 and 3.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Parts of the assembly will be
easier with 2 people.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close to
its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor (use opened
out unit carton).
1
Care and maintenance
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Safety note: It is
recommended that this unit is
secured to a wall using the
overbalance protector kit
supplied or, an alternative fixing
method of your choice.
• Dispose of all packaging
carefully and responsibly.
Drawer Front (DF3368)
(31.8 x 12.9cm) x 2
Left Drawer
Side (W280-95LH)
(28 x 9.5cm) x 2
Right Drawer Side
(W280-95RH)
(28 x 9.5cm) x 2
Drawer Back
(W291-95)
(29.1 x 9.5cm) x 2
Drawer Base
(T302-277)
(30.2 x 27.7cm) x 2
Please check you have all the panels listed below
1
2
3
4
5
Rail (DF2834)
(66.3 x 8.8cm) x 5
Front Plinth (DF2837)
(72.5 x 9.2cm)
Side Plinth (DF2838)
(30.7 x 9.1cm) x 2
6
7
8
Tools required
Scissors / Rule / Hammer / Cross-head screwdriver / Square / Spirit level
Eye protection (when using a hammer or drill) / Electric drill (only use when drilling into walls)
Components - Panels
Please check you have all the panels listed below
If you need help or have damaged or missing parts, please visit www.argos-support.co.uk
or email: Help@ClickSpares.co.uk (quoting your original order number)
Alternatively, call the Spares Helpline on: 0370 112 1928.
For any other queries please contact the Customer Helpline on: 0345 640 2020
2
9
10 12
Small Back (X663-688)
(66.3 x 68.8cm)
Left Side (DF3363)
(74.6 x 30.7cm)
Loose Shelf (DF3362)
(66.3 x 28.1cm)
Divider (DF3371)
(13.7 x 30.5cm)
Right Side (DF3364)
(74.6 x 30.7cm)
Base (DF2835)
(66.3 x 30.6cm)
Split Top (DF3365)
(73.3 X 32.7cm)
Door (DF3280)
(46.6 x 32.7cm) x 2
Top Left
Side (DF3366)
(103.5 x 25.7cm)
Large Back (X1066-688)
(106.6 x 68.8cm)
Shelf (DF3370)
(66.3 x 25.6cm) x 2
Top Right
Side (DF3367)
(103.5 x 25.7cm)
11
Top (DF3369)
(73.3 X 27.7cm)
14 15
13
16
18 19
17
20
21
Please check you have all the fittings listed below
Note: The quantities below are the correct amount to complete the assembly. In some cases
more fittings may be supplied than are required.
Components - Fittings
If you need help or have damaged or missing parts, please visit www.argos-support.co.uk
or email: Help@ClickSpares.co.uk (quoting your original order number)
Alternatively, call the Spares Helpline on: 0370 112 1928.
For any other queries please contact the Customer Helpline on: 0345 640 2020
3
Ruler - Use this ruler to help correctly identify the screws
mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
A B
D F
G H I
L
N
Small locking
nut (F3) x 4
C
M
J K
O
Drawer runner (F1004) x 4
Large locking
nut (F900) x 31
Metal dowel (F901) x 35
Wooden dowel (F22) x 39
25mm Screw (F50) x 4 9mm Screw (F74) x 4
9mm Screw (F73) x 8
Plastic Nail (F91) x 4
P Q
Hinge plate
(F523) x 4
Hinge (F522) x 4
S
Shelf stud (F110) x 4
13mm Screw (F63) x 8
Wedgefix (F639) x 4
R
Knock-in Peg (F171GY) x 8
E
Bag of Nails
(F51) x 2
Handle
(F463) x 4
38mm Screw (F81) x 4
40mm Screw (F910) x 8
T
Strap Screw Washer x 2
Overbalance protector kit (F269) x 1
1
Assembly Instructions
4
Step 1
x 2
x 2
x 2
x 2
A
B
A
C
C
C
C
2
3
Step 2
Prepare the 2 drawer
frontS
Screw 2 metal dowels
into each of the drawer
fronts .
Note: Tighten the metal
dowels up fully against
the panels.
A
1
Prepare the drawer
sides
Insert a small locking
nut into the hole
shown on the left drawer
side and the right
drawer side .
Note: The arrow on the
locking nut must point
towards the hole in the
edge of the panel.
Step 3
C
2
3
Attach the drawer
sides to the drawer
frontS
Push the left drawer side
. and right drawer side
. onto the back of the
drawer front .
Turn the small locking
nuts on the left
drawer side and right
drawer side .
Note: Turn the locking
nuts clockwise to
secure panels - more
than 1/2 a turn.
2
3
1
C
C
2
3
2
3
A
A
1
1
Assembly Instructions
5
O
O
Fit the drawer base
Slide the drawer base
down the grooves in the
drawer sides and
and down into the
groove in the drawer
front .
Step 5
Step 4
Fit the drawer back
Fit the drawer back .
between the drawer
sides and .
Make sure that the
drawer base fits into
the groove in the drawer
back .
Hold the drawer back
in position and tap the
knock-in pegs
through the holes in the
drawer sides and .
Step 6
5
2 3
1
4
2 3
5
4
4
O
2 3
Step 7
Fit the wedgefixes
Turn the top drawer
assembly over and slide
2 wedgefixes into the
front and back grooves,
as shown, and tighten up
the screws.
n
O
O
K
5
2
4
2
11
3
3
G
5
Attach the handles
Attach a handle to
each of the drawer fronts
. using screw .
Note: Do not
overtighten the screw.
G
1
N
N
S
S
1
x 2
x 2
x 2
x 2
D
D
Finished
front edge
D
D
Assembly Instructions
6
Step 8
D
10mm
A
D
Prepare top left side
Screw 5 metal dowels
into the top left side .
Tap 4 wooden dowels
into the top left side .
Note: Wooden dowels
must not stick out from
the edge by more than
10mm or they may
damage other panels.
A
9
D
9
Prepare top right side
Screw 5 metal dowels
into the top right side .
Tap 4 wooden dowels
into the top right side .
A
10
D
10
B
A
A
A
A
9
Step 9
Finished
front edge
D
D
A
A
A
A
A
10
D
D
Step 10
B
B
Prepare the 2 shelves
Insert 4 large locking
nuts into the 2
shelves .
Note: The arrow on the
locking nut must point
towards the hole in the
edge of the panel.
Tap 4 wooden dowels
into the 2 shelves .
C
B
B
D
D
B
12
12
D
12
Finished
front edge
x 2
Finished
front edge
Finished
front edge
Finished
front edge
Assembly Instructions
7
Step 11
Step 12
D
Step 13
Prepare 1 of the rails
Insert 2 large locking
nuts into 1 of the rails
. .
Tap 2 wooden dowels
into 1 of the rails .
B
6
6
D
B
B
D
6
Finished
front edge
A
B
Fit a shelf to the top
right side
Push 1 of the shelves
onto the top right side .
Use a screwdriver to
tighten the 2 large
locking nuts fitted to
the shelf .
Note: Turn the large
locking nuts as far as
they will go - more than
1/2 a turn.
10
12
B
B
12
Fit the other shelf
Push the shelf onto
the top right side .
Use a screwdriver to
tighten the 2 large
locking nuts fitted to
the shelf .
10
12
B
12
10
12
12
10
Loading...