Page 1
MADE IN
BRITAIN
Dimensions
Width - 121cm
Depth - 59.5cm
Height - 74cm
Walton - Desk
Assembly Instructions - Please keep for future reference
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
Issue 1 - 17/10/13
Important - Please read these instructions fully before starting assembly
143/6886
Page 2
Safety and Care Advice
Important - Please read these instructions fully before starting assembly
• Warning: This unit weighs
approximately 22kgs.
Please lift with care.
• Check you have all the
components and tools listed on
pages 2 and 3.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Parts of the assembly will be
easier with 2 people.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close to
its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor (use opened
out unit carton).
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Safety note: If there is any
chance of this unit being pulled
over by children etc. it is
recommended that the unit is
secured to a wall using suitable
fixings (not supplied).
• Dispose of all packaging
carefully and responsibly.
1
Care and maintenance
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
Note: If required the next page
can be cut out and used as
reference throughout the
assembly. Keep this page with
these instructions for future
reference.
Page 3
Components - Panels
Please check you have all the panels listed below
2
1
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Top (D1429A)
(1209 x 593mm)
Left Side (D1432A)
(718 x 570mm)
Top Rail (D1430A)
(1174 x 192mm)
Base Rail (D1431A)
(1174 x 120mm)
4
5
2 3
Right Side (D1433A)
(718 x 570mm)
Page 4
Please check you have all the fittings listed below
Tools required
3
Components - Fittings
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Note: The quantities below are the correct amount to complete the assembly. In some cases
more fittings may be supplied than are required.
A
Wooden dowel (F22) x 4
B
Metal dowel (F901) x 12
C
D
Large locking
nut (F900) x 12
Rule Scissors Hammer
Eye protection
(when using a
hammer or drill)
Cross-head
screwdriver
Ruler - Use this ruler to help correctly identify the screws
mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
Mini block (F25) x 2
Page 5
Assembly Instructions
4
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Step 1
Step 2
Finished
front edge
A
A
C
C
C
10mm
A
Prepare the left side
Tap 2 wooden dowels
into the left side .
Note: Wooden dowels
must not stick out from
the edge by more than
10mm or they may
damage other panels.
Screw 4 metal dowels
into the left side .
Note: Tighten the metal
dowels up fully against
the panels.
Insert 2 large locking
nuts into the left side
. .
Note: The arrow on the
locking nut must point
towards the hole in the
edge of the panel.
2
A
2
B
B
B
B
B
2
C
2
B
A
A
Prepare the right side
Tap 2 wooden dowels
into the right side .
Screw 4 metal dowels
into the right side .
Insert 2 large locking
nuts into the right
side .
C
C
B
B
B
B
3
Finished
front edge
A
3
B
3
C
3
Page 6
Assembly Instructions
5
Step 3
C
Prepare the top rail
Insert 4 large locking
nuts into the top rail
. .
Gently tap the 2 mini
blocks into the holes
on the top rail ,
orientated as shown.
D
D
D
C
C
C
C
4
Finished
front edge
C
4
D
4
Prepare the base rail
Insert 4 large locking
nuts into the base rail
. .
C
5
3
4
Step 4
Join the top rail and
right side
Push the top rail
onto the right side .
Use a screwdriver to
tighten the 2 large
locking nuts fitted to
the top rail .
Step 5
4
3
C
4
C
C
C
Finished
front edge
5
Finished
front edge
Page 7
Assembly Instructions
6
Step 6
Step 7
3
Finished
front edge
Fit the base rail
Push the base rail
onto the right side .
Use a screwdriver to
tighten the 2 large
locking nuts fitted to
the base rail .
5
3
C
5
5
Note: Support the base
rail until the left side has
been fitted in the next step.
Fit the left side
Push the left side
onto the top rail and
base rail .
Use a screwdriver to
tighten the 4 large
locking nuts fitted to
the top rail and base
rail .
2
5
4
2
5
4
C
5
4
Page 8
Assembly Instructions
7
Step 8
Step 9
Fit the top
2 people are needed
here
Lower the assembly onto
the top .
Use a screwdriver to
tighten the 4 large
locking nuts fitted to
the left side and right
side .
Finished
front edge
Prepare the top
Screw 4 metal dowels
into the top .
B
B
B
B
1
plain chipboard surface
B
1
1
Finished
front edge
1
3
2
C
2
3
Page 9
Assembly Instructions
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
and quote the reference numbers on the component pages.
Argos Ltd, 489-499 Avebury Boulevard, Central Milton Keynes, MK9 2NW
8
Step 10
Step 11
Secure the top rail to
the top
Tighten up the screws in
the 2 mini blocks ,
fitted to the top rail ,
into the holes in the top
. .
D
1
4
1
4
Stand the unit up
2 people are needed
here
Carefully lift the unit up
and turn it the correct
way up.
Assembly is complete
Page 10
Page 11
Page 12
ALR2916
Loading...