MADE IN
BRITAIN
Dimensions
Width - 50cm
Depth - 59cm
Height - 200cm
Athina - 500 Tall Cupboard
Assembly Instructions - Please keep for future reference
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
Issue 1 - 04/01/10
Important - Please read these instructions fully before starting assembly
608/0794
608/0914
608/0859
608/0976
Safety and Care Advice
Important - Please read these instructions fully before starting assembly
• Warning: This unit weighs
approximately 51kgs.
Please lift with care.
• Check you have all the
components and tools listed on
pages 2 and 3.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close to
its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor (use opened
out unit carton).
1
Care and maintenance
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
Note: If required the next page
can be cut out and used as
reference throughout the
assembly. Keep this page with
these instructions for future
reference.
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Safety note: It is
recommended that this unit is
secured to a wall using the
brackets supplied.
• Dispose of all packaging
carefully and responsibly.
Components - Panels
Please check you have all the panels listed below
2
1
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Plinth (D0322A)
(470 x 150mm)
Shelf (D0320A)
(469 x 427mm) x 2
2
Horizontal (D0319A)
(470 X 499mm) x 3
3
4
5
Left Side (D0328A)
(2000 X 570mm)
Right Side (D0329A)
(2000 X 570mm)
6
7
Back (X741)
(1848 x 480mm)
Small Door (D0317A)
(716 x 497mm)
Large Door (D0330A)
(1126 x 497mm)
8
Please check you have all the fittings listed below
Tools required
3
Components - Fittings
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Note: The quantities below are the correct amount to complete the assembly. In some cases
more fittings may be supplied than are required.
A
Wooden dowel (F22) x 20
B
Metal dowel (F901) x 14
C
D
Shelf support (F110) x 8
E F
G H I
Rule Scissors Hammer Eye protection
(when using a
hammer or drill)
Cross-head
screwdriver
Nail (F51) x 8
Ruler - Use this ruler to help correctly identify the screws
mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
J
Electric drill
Large locking
nut (F900) x 14
Bracket (F945) x 2
13mm Screw (F63) x 813mm Screw (F79) x 2
K
Hinge (F852) x 4
L
Handle (F847a ) x 2
a
L
Handle Screw (F847b) x 4
b
Door Buffer (F137) x 4
Hinge Plate
(F853) x 4
Assembly Instructions
4
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Step 1
Choose which way
you would like the
doors to open
You can fit the doors to
the left side or right side.
If you would
like your doors
to open this
way, fit the
hinge plates to
the left side
If you would like
your doors to
open this way,
fit the hinge
plates to the
right side
Step 2
B
1
J
Step 3
a:
b:
J
Prepare the left side
a: Refer to step 1 and if
required, fit 4 hinge
plates onto the left
side , making sure
that the slot is facing
towards the front edge.
b: Screw 7 metal
dowels into the holes
shown on the left side
. .
Note: Tighten metal
dowels up fully against
the panels.
1
B
1
Fit a bracket to the
left side
Fit a bracket to the
left side , 10mm down
from the top edge, see
diagram.
Secure the bracket
using screw .
Note: The bracket must
be flush with the back
edge of the panel.
1
F
F
H
J
B
B
B
B
B
J
J
J
B
F
F
H
10mm
1
1
B
Assembly Instructions
5
Step 4
Step 5
2
J
J
Prepare the right side
a: Refer to step 1 and if
required, fit 4 hinge
plates onto the right
side , making sure
that the slot is facing
towards the front edge.
b: Screw 7 metal
dowels into the holes
shown on the right side
. .
Note: Tighten metal
dowels up fully against
the panels.
2
B
2
F
F
H
Fit 2 brackets to the
right side
Fit a bracket to the
right side , 10mm
down from the top edge,
see diagram.
Secure the bracket
using screw .
Note: The bracket must
be flush with the back
edge of the panel.
2
F
F
H
B
B
B
B
B
B
J
J
J
J
2
2
Front
edge
10mm
B
A
A
A
Finished
front edge
Assembly Instructions
6
Prepare the 3
horizontals
Insert 4 large locking
nuts into each
horizontal as shown.
Note: Arrow on locking
nut must point towards
hole in edge of panel.
Tap 6 wooden dowels
into each horizontal
as shown.
Note: Wooden dowels
must not stick out from
the edge by more than
10mm or they may
damage other panels.
Step 6
Step 7
C
C
C
3
Fit the 3 horizontals
to the right side
Push the horizontals
onto the right side .
Use a screwdriver to
tighten the 2 large
locking nuts fitted to
each horizontal .
Note: Turn the large
locking nuts as far as
they will go - more than
1/2 a turn.
Step 8
B
C
3
2
C
3
C
10mm
A
C
C
5
Prepare the plinth
Insert 2 large locking
nuts into the plinth
as shown.
Tap 2 wooden dowels
into the plinth as
shown.
C
A
3
3
3
3
A
A
A
A
A
C
C
C
Finished
front edge
Finished
front edge
2
3
A
5
5
Assembly Instructions
7
Fit the plinth to the
right side
Push the plinth onto
the right side , as
shown.
Use a screwdriver to
tighten the large locking
nut fitted to the
plinth , as shown.
Note: Turn the large
locking nut as far as
they will go - more than
1/2 a turn.
Step 9
C
Step 10
Fit the left side
Push the left side
onto the assembly.
Use a screwdriver to
tighten the 7 large
locking nuts fitted to
the 3 horizontals and
plinth .
Note: Turn the large
locking nuts as far as
they will go - more than
1/2 a turn.
1
C
C
C
5
2
5
5
3
3
5
2
5
1
3
3
Assembly Instructions
8
Fit the back
a: Square up the unit by
making sure that
measurement x to x
equals y to y.
b: Slide the back
into the grooves along
the left and right
sides, as shown.
c: Secure the back
by tapping 4 nails
down into the back edge
of the top horizontal
and 4 nails into the
back edge of the bottom
horizontal .
Stand the unit up for
the next stage.
Step 11
The measurement from top corner X to bottom corner X must be
equal to the measurement from top corner Y to bottom corner Y
a:
b:
c:
y
yy
x
1 2
D
8
3
3
D
8
3
1
2
1
2
x
8
8
3
D
Assembly Instructions
9
Step 12
Step 13
Secure the unit to the
wall
Using the brackets
fitted to the back edge of
the sides and
screw the unit to the
wall.
Fixings are not supplied
as they will need to suit
the wall type, and the
length of screw will
depend on the distance
of the back of the Unit to
the wall.
Warning: Take
care when
drilling the wall
that you do not drill into
any pipes, wires etc. If in
doubt, consult an expert.
F
2
1
2
1
2
1
E
x 4
E
x 4
Fit the shelf studs
Choose the height
required for the 2
shelves.
For each shelf, push 4
shelf studs into the
holes in the side panels
. and .
E
1 2
F
F