Argos ZVK500TC-B-AR ASSEMBLY INSTRUCTIONS

MADE IN

BRITAIN

Dimensions

Width - 50cm

Depth - 59cm

Height - 200cm

Athina - 500 Tall Cupboard

Assembly Instructions - Please keep for future reference

If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800

Issue 2 - 25/03/11

Important - Please read these instructions fully before starting assembly

608/0794

608/0914

608/0859

608/2967

608/0976

Safety and Care Advice

Important - Please read these instructions fully before starting assembly

• Warning: This unit weighs approximately 51kgs. Please lift with care.

• Check you have all the components and tools listed on pages 2 and 3.

• Remove all fittings from the plastic bags and separate them into their groups.

• Keep children and animals away from the work area, small parts could choke if swallowed.

• Make sure you have enough space to layout the parts before starting.

• Do not stand or put weight on the product, this could cause damage.

• Assemble the item as close to its final position (in the same room) as possible.

• Assemble on a soft level surface to avoid damaging the unit or your floor (use opened out unit carton).

Care and maintenance

• Only clean using a damp cloth and mild detergent, do no use bleach or abrasive cleaners.

• From time to time check that there are no loose screws on this unit.

• This product should not be discarded with household waste. Take to your local authority waste disposal centre.

Note: If required the next page can be cut out and used as reference throughout the assembly. Keep this page with these instructions for future reference.

• We do not recommend the use of power drill/drivers for

inserting screws, as this could damage the unit. Only use hand screwdrivers.

• Safety note: It is recommended that this unit is secured to a wall using the brackets supplied.

• Dispose of all packaging carefully and responsibly.

Components - Panels

Please check you have all the panels listed below

If you have damaged or missing components, call the

Customer Helpline: 08456 400800 quoting the reference

numbers below

Plinth (D0322A)

(470 x 150mm)

Shelf (D0320A)

(469 x 427mm) x 3

Horizontal (D0319A)

(470 X 499mm) x 3

Left Side (D0328A)

(2000 X 570mm)

Right Side (D0329A)

(2000 X 570mm)

Back (X741)

(1848 x 480mm)

Small Door (D0317A)

(716 x 497mm)

Large Door (D0330A)

(1126 x 497mm)

Please check you have all the fittings listed below

Tools required

Components - Fittings

If you have damaged or missing components, call the

Customer Helpline: 08456 400800 quoting the reference

numbers below

Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings may be supplied than are required.

Wooden dowel (F22) x 20

Metal dowel (F901) x 14

Shelf support (F110) x 12

E F

G H I

Rule Scissors Hammer Eye protection

(when using a hammer or drill)

Cross-head screwdriver

Nail (F51) x 8

Ruler - Use this ruler to help correctly identify the screws

mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170

Electric drill

Large locking nut (F900) x 14

Bracket (F945) x 2

13mm Screw (F63) x 813mm Screw (F79) x 2

Hinge (F852) x 4

Handle (F847a ) x 2

Handle Screw (F847b) x 4

Door Buffer (F137) x 4

Hinge Plate (F853) x 4

Assembly Instructions

If you have damaged or missing components, call the

Customer Helpline: 08456 400800 quoting the reference

numbers below

Step 1

Choose which way you would like the doors to open

You can fit the doors to the left side or right side.

If you would

like your doors

to open this

way, fit the

hinge plates to

the left side

If you would like

your doors to

open this way,

fit the hinge

plates to the

right side

Step 2

Step 3

Prepare the left side

a: Refer to step 1 and if

required, fit 4 hinge plates onto the left side , making sure that the slot is facing towards the front edge.

b: Screw 7 metal

dowels into the holes shown on the left side . .

Note: Tighten metal dowels up fully against the panels.

Fit a bracket to the left side

Fit a bracket to the left side , 10mm down from the top edge, see diagram.

Secure the bracket using screw .

Note: The bracket must be flush with the back edge of the panel.

10mm

+ 11 hidden pages