Argos ZVK500BU-HO-AR ASSEMBLY INSTRUCTIONS

MADE IN

BRITAIN

Dimensions

Width - 50cm

Depth - 59cm

Height - 89.5cm

Athina - 500 Base Unit

Assembly Instructions - Please keep for future reference

If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800

Issue 1 - 14/01/10

Important - Please read these instructions fully before starting assembly

608/0828

608/0945

608/0880

608/1009

Safety and Care Advice

Important - Please read these instructions fully before starting assembly

• Warning: This unit weighs approximately 26kgs. Please lift with care.

• Check you have all the components and tools listed on pages 2 and 3.

• Remove all fittings from the plastic bags and separate them into their groups.

• Keep children and animals away from the work area, small parts could choke if swallowed.

• Make sure you have enough space to layout the parts before starting.

• Do not stand or put weight on the product, this could cause damage.

• Assemble the item as close to its final position (in the same room) as possible.

• Assemble on a soft level surface to avoid damaging the unit or your floor (use opened out unit carton).

1

Care and maintenance

• Only clean using a damp cloth and mild detergent, do no use bleach or abrasive cleaners.

• From time to time check that there are no loose screws on this unit.

• This product should not be discarded with household waste. Take to your local authority waste disposal centre.

Note: If required the next page can be cut out and used as reference throughout the assembly. Keep this page with these instructions for future reference.

• We do not recommend the use of power drill/drivers for

inserting screws, as this could damage the unit. Only use hand screwdrivers.

• Safety note: It is recommended that this unit is secured to a wall using the bracket supplied.

• Dispose of all packaging carefully and responsibly.

Components - Panels

Please check you have all the panels listed below

2

1

If you have damaged or missing components, call the

Customer Helpline: 08456 400800 quoting the reference

numbers below

Left Side (D0315A)

(870 X 570mm)

Back (X739)

(480 x 533mm)

Rail (D0321A)

(470 x 60mm) x 2

Plinth (D0322A)

(470 x 150mm)

Right Side (D0316A)

(870 x 570mm)

Top (D0338A)

(500 x 590mm)

Shelf (D0320A)

(469 x 427mm)

Door (D0317A)

(716 x 497mm)

2 3

Base (D0319A)

(470 X 499mm)

4 5

6

8 9

7

Please check you have all the fittings listed below

Tools required

3

Components - Fittings

If you have damaged or missing components, call the

Customer Helpline: 08456 400800 quoting the reference

numbers below

Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings may be supplied than are required.

A

Wooden dowel (F22) x 12

B

Metal dowel (F901) x 10

C

D

Shelf support (F110) x 4

E F

G H I

Rule Scissors Hammer Eye protection

(when using a hammer or drill)

Cross-head screwdriver

Nail (F51) x 8

Ruler - Use this ruler to help correctly identify the screws

mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170

J

Door Buffer (F137) x 2

L

Electric drill

Large locking nut (F900) x 10

Bracket (F945) x 4

25mm Screw (F50) x 2

13mm Screw (F63) x 413mm Screw (F79) x 6

K

Hinge Plate (F853) x 2

Hinge (F852) x 2

M

Handle (F847a ) x 1

a

M

Handle Screw (F847b) x 2

b

Assembly Instructions

4

If you have damaged or missing components, call the

Customer Helpline: 08456 400800 quoting the reference

numbers below

Step 1

Choose which way you would like the door to open

You can fit the door to the left side or right side.

If you would

like your door

to open this

way, fit the

hinge plates

to the left side

If you would

like your door

to open this

way, fit the

hinge plates to

the right side

Step 2

B

1

K

Front edge

Step 3

a:

b:

K

Prepare the left side

a: Refer to step 1 and, if

required, fit 2 hinge plates onto the left side , making sure that the slot is facing towards the front edge.

b: Screw 5 metal

dowels into the holes shown on the left side . .

Note: Tighten metal dowels up fully against the panels.

1

B

1

Fit 2 brackets to the left side

Fit a bracket to the left side , 100mm in from the back edge, see diagram.

Fit another bracket to the left side , 100mm down from the top edge, see diagram.

Secure each bracket using screw .

Note: The brackets must be flush with the edges of the panel.

1

F

H

1

100mm

F

H

F

H

Assembly Instructions

5

Step 4

Step 5

B

2

Front edge

K

2

K

Prepare the right side

a: Refer to step 1 and, if

required, fit 2 hinge plates onto the right side , making sure that the slot is facing towards the front edge.

b: Screw 5 metal

dowels into the holes shown on the right side . .

Note: Tighten metal dowels up fully against the panels.

2

B

2

100mm

F

HH

Fit 2 brackets to the right side

Fit a bracket to the right side , 100mm down from the back edge, see diagram.

Fit another bracket to the right side , 100mm down from the top edge, see diagram.

Secure each bracket using screw .

Note: The brackets must be flush with the edges of the panel.

2

F

H

2

F

A

Finished

front edge

Assembly Instructions

6

Prepare the base

Insert 4 large locking nuts into the base as shown.

Note: Arrow on locking nut must point towards hole in edge of panel.

Tap 6 wooden dowels into the base as shown.

Note: Wooden dowels must not stick out from the edge by more than 10mm or they may damage other panels.

Step 6

Step 7

C

4

C

4

Fit the base to the right side

Push the base onto the right side .

Use a screwdriver to tighten the 2 large locking nuts fitted to the base .

Note: Turn the large locking nuts as far as they will go - more than 1/2 a turn.

Step 8

B

4

C

2

4

2

C

4

C

A

C

A

6

10mm

A

C

7

Prepare the 2 rails and plinth

Insert 2 large locking nuts into each of the 2 rails and plinth as shown.

Tap 2 wooden dowels into the 2 rails and plinth as shown.

C

6

7

6

7

A

4

Assembly Instructions

7

Fit the 2 rails and plinth

One at a time, push the 2 rails and plinth onto the right side as shown.

Use a screwdriver to tighten the 3 large locking nuts fitted to the 3 panels, as shown.

Note: Turn the large locking nuts as far as they will go - more than 1/2 a turn.

Step 9

2

6

7

6 7

2

C

Step 10

Fit the left side

Push the left side onto the assembly.

Use a screwdriver to tighten the 5 large locking nuts fitted to the base , rails and plinth .

Note: Turn the large locking nuts as far as they will go - more than 1/2 a turn.

6

7

1

4

C

6

1

4

C

Assembly Instructions

8

Fit the back

a: Square up the unit by

making sure that measurement x to x

equals y to y.

b: Slide the back

into the grooves along the left and right sides, as shown.

c: Secure the back

by tapping 4 nails down into the back edge of the base and 4 nails into the back edge of the rail .

Step 11

9

D

The measurement from top corner X to bottom corner X must be

equal to the measurement from top corner Y to bottom corner Y

a:

b:

c:

x

y

yy

x

1 2

D

9

4

6

D

4

6

9

Assembly Instructions

9

Step 12

Step 13

Secure the front of the top

To secure the front of the top , screw up through the 2 holes in the rail at the front of the unit using screws .

3

H

F

3

2

1

Fit the top

Position the top onto the unit, making sure that the back edge is flush with the back edge of the sides and .

Secure the top using screw through the 2 brackets fitted at the top edge of the side panels and .

H

3

2

1

3

F

2

1

3

1

3

6

G