Argos ZVK100BU-B-AR ASSEMBLY INSTRUCTIONS

Page 1
MADE IN
BRITAIN
Dimensions
Width - 100cm
Depth - 59cm
Height - 89.5cm
Athina - 1000 Base Unit
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
Issue 3 - 01/02/12
Important - Please read these instructions fully before starting assembly
608/0811
608/0938
608/0873
608/2981
608/0990
Page 2
Safety and Care Advice
Important - Please read these instructions fully before starting assembly
Warning: This unit weighs approximately 42kgs. Please lift with care.
• Check you have all the components and tools listed on pages 2 and 3.
• Remove all fittings from the plastic bags and separate them into their groups.
• Keep children and animals away from the work area, small parts could choke if swallowed.
• Make sure you have enough space to layout the parts before starting.
• Do not stand or put weight on the product, this could cause damage.
• Assemble the item as close to its final position (in the same room) as possible.
• Assemble on a soft level surface to avoid damaging the unit or your floor (use opened out unit carton).
1
Care and maintenance
• Only clean using a damp cloth and mild detergent, do no use bleach or abrasive cleaners.
• From time to time check that there are no loose screws on this unit.
• This product should not be discarded with household waste. Take to your local authority waste disposal centre.
Note: If required the next page can be cut out and used as reference throughout the assembly. Keep this page with these instructions for future reference.
• We do not recommend the use of power drill/drivers for
inserting screws, as this could damage the unit. Only use hand screwdrivers.
Safety note: It is recommended that this unit is secured to a wall using the brackets supplied.
• Dispose of all packaging carefully and responsibly.
Page 3
Components - Panels
Please check you have all the panels listed below
2
1
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Door (D0317A)
(716 x 497mm) x 2
2
9
Base (D0323A)
(970 X 499mm)
Shelf (D0324A)
(969 X 427mm)
Top (D0339A)
(1000 x 590mm)
Back (X740)
(980 x 533mm)
3
4 5
6 7
8
10
Left Side (D0315B)
(870 X 570mm)
Right Side (D0316B)
(870 x 570mm)
Rail (D0325A)
(970 x 60mm) x 2
Plinth (D0326A)
(970 x 150mm)
Munting (D0327A)
(689 x 59mm)
Page 4
Please check you have all the fittings listed below
Tools required
3
Components - Fittings
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings may be supplied than are required.
A
Wooden dowel (F22) x 14
B
Metal dowel (F901) x 10
C
D
Shelf support (F110) x 4
E F
G H I
Rule Scissors Hammer Eye protection
(when using a hammer or drill)
Cross-head screwdriver
Nail (F51) x 14
Ruler - Use this ruler to help correctly identify the screws
mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
J
Door Buffer (F137) x 4
L
Electric drill
Large locking nut (F900) x 10
Bracket (F945) x 4
25mm Screw (F50) x 4
13mm Screw (F63) x 813mm Screw (F79) x 6
K
Hinge Plate (F853) x 4
Hinge (F852) x 4
M
Handle (F847a ) x 2
a
M
Handle Screw (F847b) x 4
b N
40mm Screw (F910) x 2
Page 5
Front edge
Assembly Instructions
4
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Step 1
B
B
B
B
B
B
1
1
1
K
K
K
Front edge
Step 2
a:
b:
K
Prepare the left side
a: Fit 2 hinge plates
onto the left side , making sure that the slot is facing towards the front edge.
b: Screw 5 metal
dowels into the holes shown on the left side . .
Note: Tighten metal dowels up fully against the panels.
1
B
1
Fit 2 brackets to the left side
Fit a bracket to the left side , 100mm in from the back edge, see diagram.
Fit another bracket to the left side , 100mm down from the top edge, see diagram.
Secure each bracket using screw .
Note: The brackets must be flush with the edges of the panel.
1
F
F
H
1
100mm
100mm
F
F
F
H
F
H
Page 6
Assembly Instructions
5
Step 3
Step 4
B
B
B
B
B
2
2
Front edge
K
K
2
K
K
Prepare the right side
a: Fit 2 hinge plates
onto the right side , making sure that the slot is facing towards the front edge.
b: Screw 5 metal
dowels into the holes shown on the right side . .
Note: Tighten metal dowels up fully against the panels.
2
B
2
100mm
100mm
F
F
HH
Fit 2 brackets to the right side
Fit a bracket to the right side , 100mm down from the back edge, see diagram.
Fit another bracket to the right side , 100mm down from the top edge, see diagram.
Secure each bracket using screw .
Note: The brackets must be flush with the edges of the panel.
2
F
F
H
2
F
F
Front edge
Page 7
Assembly Instructions
6
Prepare the base
Insert 4 large locking nuts into the base as shown.
Note: Arrow on locking nut must point towards hole in edge of panel.
Tap 6 wooden dowels into the base as shown.
Note: Wooden dowels must not stick out from the edge by more than 10mm or they may damage other panels.
Step 5
Step 6
C
C
4
Fit the base to the right side
Push the base onto the right side .
Use a screwdriver to tighten the 2 large locking nuts fitted to the base .
Note: Turn the large locking nuts as far as they will go - more than 1/2 a turn.
4
2
C
4
C
10mm
A
A
4
A
A
A
C
C
A
A
A
C
C
4
Finished
front edge
B
4
C
2
Page 8
Assembly Instructions
7
Step 7
Step 8
Fit a rail to the right side
Push one of the rails onto the right side as shown.
Use a screwdriver to tighten the large locking nut .
Note: Turn the large locking nuts as far as they will go - more than 1/2 a turn.
6
2
C
C
A
C
C
A
6
Prepare the 2 rails and munting
Insert 2 large locking nuts and 2 wooden dowels into each of the 2 rails .
Tap 2 wooden dowels into the munting .
C
6
8
A
A
8
A
A
2
6
Page 9
Assembly Instructions
8
Step 9
A
A
C
C
7
Prepare the plinth
Insert 2 large locking nuts and 2 wooden dowels into the plinth . .
C
7
A
Fit the munting
Fit the munting to the rail and base and secure using 2 screws . .
8
N
6 4
Step 10
N
8
N
6
4
Page 10
Assembly Instructions
9
Step 11
Step 12
6
Fit the rail and plinth
Push the rail and plinth onto the right side as shown.
Use a screwdriver to tighten the 2 large locking nuts fitted to the 2 panels, as shown.
Note: Turn the large locking nuts as far as they will go - more than 1/2 a turn.
Note: Support the rail . until the left side has been fitted in the next stage.
7
2
C
C
6
Fit the left side
Push the left side onto the assembly.
Use a screwdriver to tighten the 5 large locking nuts fitted to the base , rails and plinth .
Note: Turn the large locking nuts as far as they will go - more than 1/2 a turn.
6
7
1
4
C
C
2
6
7
6
6
6
7
4
1
Page 11
Assembly Instructions
10
Step 13
Fit the back
a: Square up the unit by
making sure that measurement x to x
equals y to y.
b: Slide the back
into the grooves along the left and right sides, as shown.
c: Secure the back
by tapping 7 nails down into the back edge of the base and 7 nails into the back edge of the rail .
Stand the unit up for the next stage.
The measurement from top corner X to bottom corner X must be
equal to the measurement from top corner Y to bottom corner Y
a:
1 2
D
10
4
6
D
10
b:
c:
x
y
y
x
10
10
D
1
2
6
4
Page 12
Assembly Instructions
Step 14
11
Step 15
Secure the front of the top
To secure the front of the top , screw up through the 4 holes in the rail at the front of the unit using screws .
Fit the top
Position the top onto the unit, making sure that the back edge is flush with the back edge of the sides and .
Secure the top using screw through the 2 brackets fitted at the top edge of the side panels and .
H
3
2
1
3
F
2
1
3
6
G
H
F
H
F
G
G
G
G
3
6
3
2
1
Page 13
Assembly Instructions
12
Step 16
Secure the unit to the wall
Using the brackets fitted to the back edge of the sides and screw the unit to the wall.
Fixings are not supplied as they will need to suit the wall type, and the length of screw will depend on the distance of the back of the Unit to the wall.
Warning: Take care when
drilling the wall that you do not drill into any pipes, wires etc. If in doubt, consult an expert.
Step 17
F
2
1
Fit the shelf studs
Push 4 shelf studs into the holes in the side panels and at the desired height.
E
1 2
F
F
E
E
E
E
2
1
2
1
Page 14
Assembly Instructions
13
Step 18
Step 19
Fit the shelf
Manouvre the shelf into the unit onto the shelf studs .
5
E
Prepare the 2 doors
Push fit the 2 hinges into the door .
Secure each hinge with 2 screws .
Note: Before securing with the screws, make sure that the hinges are positioned at 90 degrees with the front edge of the door.
I
L
9
9
L
I
I
L
I
I
90
L
5
Page 15
Assembly Instructions
14
Step 20
Small piece of
waste wood
Small piece of
waste wood
ONLY drill
these 2 holes
ONLY drill
these 2 holes
DO NOT drill
these holes
DO NOT drill
these holes
9
9
Drill the handle holes in the door
Important: Please follow these instructions carefully.
Lay the doors down onto a smooth surface.
Important: Check that the holes and hinges are in the same place as the diagrams.
Note: We recommend the use of a small piece of waste wood, placed behind the hole while drilling, to reduce the possibility of any breakout.
Using the pilot hole in the rear face of the door , drill through the holes indicated opposite, using a 2.5mm diameter drill.
Turn the door over and open out the 2.5mm holes that you have just drilled by drilling back through them with a 5mm drill.
This will be
the left door
This will be
the right door
9
9
9
IMPORTANT
Carefully choose which 2 holes you
need to drill in each of the doors
Page 16
Assembly Instructions
Step 21
screw A
a: b:
c: d:
A
screw B
L
L
LL
K
K
K
K
e:
Fit doors and handles
2 people are needed here
Note: The easiest way to
attach the door is to fit the top hinge first, then align and fit the other hinges.
a: Push the hinge
onto the front part of the hinge plate .
b: Keep the hinge
FLAT against the hinge plate as you slide it across as far as it will go. Tighten screw A.
c: The hinge must be
flat against the hinge plate prior to any adjustment.
d: The hinge must
NOT be AT AN ANGLE to the hinge plate when assembled. This would indicate that the recess at the bottom of screw B had not located in the slot in the hinge plate and the hinge would not be secure. Remove the hinge from the hinge plate and then re-assemble being careful to follow instructions a-c.
e: Attach a
handle to the door . using 2 screws .
L
L
L
K
K
K
L
K
9
M a
9
M b
9
M a
M b
M b
15
M a
Page 17
Assembly Instructions
16
Step 22
Adjust the doors if needed
a: Height adjustment.
Loosen screws A on hinge plates and move door up or down as required. Retighten screw A.
b: Forward and Back
adjustment. Loosen screw B on hinge plate and move door in or out as required. Retighten screw B.
c: Sideways
adjustment. To move door ‘out’ loosen screw C. To move door ‘in’ tighten screw C
Fit the door buffers to both doors
Stick a door buffer onto each corner of the door so that they hit the edge of the side panel when the door is closed.
Step 23
J
9
a:
b:
c:
A
A
B
C
9
J
J
Page 18
Assembly Instructions
17
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
and quote the reference numbers on the component pages.
Argos Ltd, 489-499 Avebury Boulevard, Central Milton Keynes, MK9 2NW
Step 24
Assembly is complete
Warning: The
unit is heavy.
Lift with care.
Page 19
Page 20
ALR2458
Loading...